Page 1
Model:LBT-HS310M
1: Volume up
2: Volume down
3: mini USB jack.
4: Indicate LED
5: MFB button
6: Microphone
7. NFC area
1 2 3
5 6 4
7
Brand:ELECOM
Bluetooth headset
Bluetooth™ headset connect with your cellular phone (with Bluetooth™
function) give you a safety way to none stop communication in driving.
It supports NFC easy pairing function(Receive tag only).
Headset instruction:
Page 2
Function Keys
Location
Keys
Function
Volume up
Volume up or forward function
Volume down
Volume down or backward function
MFB button
Power on / off / Play/Pause/ call function
Color
LED Status
Function
Blue
Status LED flashes 2 times
every 5 seconds
Linked
Status LED and Charging LED
Flash alternative
Pairing state
Red
Red LED flashes 1 time every 5
seconds
Standby(no connection )
Charging LED flashes slowly
every 3 seconds
Low battery
Charging LED lights up steady
Charging (Indicator turns off when
charging is completed.)
LED indicators
How to start
After opening the package, please make sure to do the following steps
1. Full charge the headset by charge it first time at least 2 hours.
The Red LED will be steady on when charging. The LED will go off when
battery is fully charged. Press MFB key about 3 seconds to power on the
headset. When the headset power on the blue led will flash 3 times and you
can hear a rising tone. When headset already power on, press MFB key
about 3~5 seconds will power off the headset. When the headset power off
the red led will flash 3 times and you can hear a falling tone.
2. Link (Pairing) headset to your Bluetooth™ mobile phone or other
Bluetooth™ devices for the first time only.
Press and hold the MFB button for three seconds to wait for the Blue led
steady on that indicates the headset is into the paring mode.
Operate your Bluetooth™ mobile phone or other Bluetooth™ device to start
Bluetooth™ function. Find the headset “LBT-HS310M”, press the pairing
Page 3
code “0000” The blue LED is start flashing, the headset is in connected
mode
3. Standby mode :
Double click MFB key to initiate voice dial
Long press main key to power off headset
Short press Vol+ and Vol- key to initiate Last Number redial
Short press MFB key for play/pause function
Long press MFB and Vol+ for proximity pairing
Long press MFB and Vol- for clear paired information
4. Music play:
Short press MFB key for play/pause function
Long press Vol+ key for forward function
Long press Vol- key for backward function
5. Incoming call:
Short press MFB key to accept call
Long press MFB key till hear beep tone to reject call
6. In Talking:
Short press volume up key to adjust volume up
Short press volume down key to adjust volume down
Long press MFB key to toggle call between headset and
cellular phone
Short press MFB key to end call
long press Vol+ and Vol- to toggle microphone mute function
7. NFC easy pairing (Receive tag only).
Power On: Mobile phone short touch the BEC3470, blue and
red LED flash alternatively for into pairing mode. You
can auto-connect to the headset.
Connect: Mobile phone short touch with the BEC3470 when
headset is disconnected
Power Off: Mobile phone short touch with the BEC3470 when
headset is connected.
Page 4
8. Led statuses
POWER ON
Blue led flash 3 times
POWER OFF
Red led flash 3 times
PAIRING
Blue and red led flash alternatively
STANDBY MODE
Red led flash once every 5 seconds
A2DP SBC MODE
Blue led flash twice every 5 seconds
HEADSET ACTIVE MODE
Blue led flash once( 1 second dim led)every 5 seconds
LOW BATTERY INDICATION
Red led flash twice every 3 seconds
AUTO SHUTDOWN
Red led flash 3 times and power off (5 minutes no any
connection)
9. Troubleshooting
If the Bluetooth Headset does not work, try the following:
-Ensure connecting devices are charged
-Turn off all devices and then turn them on in order to shown in this guide
-Ensure devices are within 10 meter range
-Ensure the Headset is connected by check the blue LED flash
Note 1: Some A2DP source like 3.5mm interface transmitter cannot support
AVRCP profile, so it cannot do remote control function.
Note 2: Only cellular phone supports hands free profile can use voice dial, last
number redial, call transfer function
Page 5
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.
Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in
this manual. The further RF exposure reduction can be achieved if the product
can be kept as far as possible from the user body or set the device to lower
output power if such function is available.
Page 6
電信管制射頻器材警語：
低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商
號或使用者均不得擅自變更頻率、加大功率或變更原設計之
特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通
信；經發現有干擾現象時，應立即停用，並改善至無干擾時
方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波
輻射性電機設備之干擾。
Loading...