General Electric UVW9301BLTS Use & Care
SAFETY INFORMATION .............3
USING THE HOOD
Controls ..................................5
Chef Connect ............................ 6
Wi-Fi Connect ............................ 6
CARE AND CLEANING
Filters ....................................7
Surfaces ..................................8
Lights ....................................8
INSTALLATION INSTRUCTIONS ... 9
TROUBLESHOOTING TIPS ..........21
WARRANTY ......................... 22
ACCESSORIES ...................... 23
CONSUMER SUPPORT ............. 24
OWNER’S MANUAL &
INSTALLATION
INSTRUCTIONS
UVW9301
UVW9361
Write the model and serial
numbers here:
WALL HOODS
GE is a trademark of the General Electric Company. Manufactured under trademark license.
Model # _________________
Serial # _________________
You can find them on a label
on the inside of the hood.
Para consultar una version en
español de este manual de
instrucciones, visite nuestro sitio de
internet GEAppliances.com.
49-80795-1 03-18 GEA
ESPAÑOL
THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.
Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.
We take pride in the craftsmanship, innovation and design that goes into every GE Appliances
product, and we think you will too. Among other things, registration of your appliance ensures that we
can deliver important product information and warranty details when you need them.
Register your GE appliance now online. Helpful websites and phone numbers are available in the
Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration
card included in the packing material.
2 49-80795-1
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING
SAFETY INFORMATION
WARNING
ELECTRIC SHOCK OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
A. Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
B. Before servicing or cleaning unit, switch power off
at service panel and lock the service disconnecting
means to prevent power from being switched
on accidentally. When the service disconnecting
means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the
service panel.
C. Do not use this unit with any solid-state speed
control device.
D. This unit must be grounded.
CAUTION
ONLY. DO NOT USE TO EXHAUST HAZARDOUS
OR EXPLOSIVE MATERIALS AND VAPORS.
CAUTION
TO PROPERLY EXHAUST AIR, BE SURE TO DUCT
AIR OUTSIDE. DO NOT VENT EXHAUST AIR INTO
SPACES WITHIN WALLS OR CEILINGS OR INTO
ATTICS, CRAWL SPACES OR GARAGES.
TO REDUCE THE RISK OF FIRE,
FOR GENERAL VENTILATING USE
TO REDUCE RISK OF FIRE AND
WARNING
TO PERSONS IN THE EVENT OF A RANGE TOP
GREASE FIRE, OBSERVE THE FOLLOWING*:
A. SMOTHER FLAMES with a close-fitting lid, cookie
sheet or metal tray, then turn off the burner. BE
CAREFUL TO PREVENT BURNS. If the flames do
not go out immediately, EVACUATE AND CALL
THE FIRE DEPARTMENT.
B. NEVER PICK UP A FLAMING PAN—You may be
burned.
C. DO NOT USE WATER, including wet dishcloths or
towels—a violent steam explosion will result.
D. Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher,
and you already know how to operate it.
2. The fire is small and contained in the area where
it started.
3. The fire department is being called.
4. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety” published by NFPA.
TO REDUCE THE RISK OF INJURY
READ AND SAVE THESE INSTRUCTIONS
49-80795-1 3
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING
WARNING
RANGE TOP GREASE FIRE:
A. Never leave surface units unattended at high
settings. Boilovers cause smoking and greasy
spillovers that may ignite. Heat oils slowly on
medium settings.
B. Always turn hood ON when cooking at high heat or
when flambéing food (i.e. Crepes Suzette, Cherries
Jubilee, Peppercorn Beef Flambé).
C. Clean ventilating fans frequently. Grease should not
be allowed to accumulate on fan or filter.
SAFETY INFORMATION
D. Use proper pan size. Always use cookware
appropriate for the size of the surface element.
WARNING
ELECTRIC SHOCK OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
A. Installation work and electrical wiring must be
done by qualified person(s) in accordance with all
applicable codes and standards, including fire-rated
construction.
B. Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of
fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer’s
guidelines and safety standards such as those
published by the National Fire Protection
Association (NFPA), the American Society for
Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE) and the local code authorities.
TO REDUCE THE RISK OF A
TO REDUCE THE RISK OF FIRE,
C. When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
D. Ducted fans must always be vented to the outdoors.
E. When applicable, install any makeup (replacement)
air system in accordance with local building
code requirements. Visit GEAppliances.com for
available makeup air solutions.
F. Turn off breaker to adjacent rooms while working.
WARNING
USE ONLY METAL DUCTWORK.
Ŷ'RQRWDWWHPSWWRUHSDLURUUHSODFHDQ\SDUWRI\RXU
hood unless it is specifically recommended in this
manual. All other servicing should be referred to a
qualified technician.
TO REDUCE THE RISK OF FIRE,
How to Remove Protective Shipping Film and Packaging Tape
Carefully grasp a corner of the protective shipping film
with your fingers and slowly peel it from the appliance
surface. Do not use any sharp items to remove the film.
Remove all of the film before using the appliance for the
first time.
To assure no damage is done to the finish of the
product, the safest way to remove the adhesive from
packaging tape on new appliances is an application of
a household liquid dishwashing detergent. Apply with a
soft cloth and allow to soak.
NOTE: The adhesive must be removed from all parts.
NOTE: For further cleaning instructions/suggestions,
please refer to the Care And Cleaning section.
READ AND SAVE THESE INSTRUCTIONS
4 49-80795-1
Controls
1 9
USING THE HOOD: Controls
3
6
25678
3
4
1. Rangehood Control Panel: The control
panel is located on the front of the canopy. The
position and function of each control pad are
noted below.
2. On/Off: On/Off switch for the fan and lighting up
the display. The fan can be operated by tapping
any of the fan setting pads. Hold On/Off pad for
3 seconds to activate Delay Off feature, which
automatically turns the fan off after 15 minutes.
3. Fan Setting: Speed control for fan. Tap Low
for LOW speed. Med for MEDIUM speed and High
for HIGH speed. Press and hold the High pad for 3
seconds to activate the BOOST speed that will run
for 10 minutes. On Remote, press Up to increase
fan speed, press Down to decrease fan speed,
including Boost.
4. Plus and Minus: The plus (+) and minus (–)
pads control the time for the clock and the timer.
To add time, tap the + pad. To subtract time, tap
the – pad.
5. Timer: Sets a timer for cooking or sets the clock.
To start the timer, tap the Timer pad and the clock
will show “HR” and “MIN”. Tap + or – to add or
subtract time. Tap on the Timer again to start the
countdown. To cancel the timer, tap the Timer pad
again. Hold the Timer pad down for 3 seconds to
set the clock. Tap the + or – to set the the hour.
Tap on the Timer again to set minutes. Tap on the
Timer again to lock in the time. Clock will sync once
the unit is connected to Wi-Fi.
10
9
7
2
Remote Control
6. Light: Controls the lights. Tap the Light pad to
turn the lights on fully. Tap the Light pad again and
the lights will dim. Tap the Light pad a third time to
turn off the lights.
7. Chef Connect: Hold the Chef Connect pad
down for 3 seconds to activate the Bluetooth®. This
is a Bluetooth® pairing feature for use with other
compatible Chef Connect enabled products on a
cooktop or range. When the device is paired, the light
and fan will turn ON at the Default Sync Settings upon
receiving a command from the range or cooktop. It
will remain ON at that setting until the user changes
it. See the Chef Connect section for more details.
8. Reset Filter: The red LED indicator above the
Reset Filter pad turns on as a reminder to change
/clean the filter. Hold the Reset Filter pad for 3
seconds to turn off. Tap the Reset Filter pad again
to begin recalculating the time. While this indicator
reminds user to change/clean filters, the filters
should be cleaned regularly. Please refer to the
Filters section.
9. Wi-Fi: Hold down the Light and Chef Connect
pads for three seconds to activate the Wi-Fi connect
mode. The Wi-Fi symbol above the clock blinks for
3 seconds and then becomes solid. See the Wi-Fi
section for more details. On Remote, press Wi-Fi to
toggle Wi-Fi function.
10. Delay Off (Remote only): Press and hold
Delay Off to toggle Delay Off function.
49-80795-1 5
Chef Connect
Chef Connect Operation Bluetooth® Connection
To pair with another device:
To start the pairing process on the hood, press and hold
the Chef Connect button for 3 seconds. The backlight
for all the icons will light up until the hood is paired with
the range or other device. If the pairing is successful,
the Bluetooth
become solid.
It will time out after 2 minutes if the pairing is not
completed, after which the pairing sequence will need to
be restarted.
To cancel pairing:
To cancel the pairing, hold the Chef Connect button
down for 3 seconds and then turn off the hood.
®
symbol above the clock will turn on and
Default Sync Settings:
The factory default setting for the light will be the brightest.
The factory default setting for the fan sync will be OFF.
The user can change the Default Sync Settings by
pressing and holding the Low button for 3 seconds. This
will enter the Default Settings Mode. Once in this mode,
the backlights for all buttons will blink on/off indefinitely
and the fan and light will switch to the current Default
Sync Setting, so the user knows what the current default
value is. At this time, set the light and fan to the desired
default levels. Once the user is satisfied with the selection,
press and hold the Off button for 3 seconds. This will exit
this mode. At that time the backlights will stop blinking and
the state of the fan and light will change back to their prior
state before entering the Default Settings Mode.
Wi-Fi Connect
Connecting your Wi-Fi Connect Enabled hood (on some models)
Your GE Appliances hood is designed to provide you with two-way communication between your appliance and smart
device. By using the GE Appliances Wi-Fi Connect features, you will be able to control essential hood operations such
as fan speed, light functions, timer/clock function, delay off and filter reset using your smartphone or tablet.*
What you will need
Your GE Appliances hood uses your existing home Wi-Fi
network to communicate between the appliance and your
smart device. In order to setup your GE Appliances hood,
you will need to gather some information:
1. Each GE Appliances hood has a connected
appliance information label that includes an
Appliance Network Name and Password. These
USING THE HOOD: Chef Connect / Wi-Fi Connect
are the two important details that you will need to
connect to the appliance. The label is located on the
side of the unit behind the filters.
Connected Appliance Information
FCC ID: ZKJ-WCATA005
IC: 10229A-WCATA001
MAC ID: ************
Sample Label
2. Have your smart phone or tablet ready with the ability
to access the internet and download apps.
3. You will need to know the password of your home
Wi-Fi router. Have this password ready while you are
setting up your GE Appliances hood.
Network: ************
Password: **********
Connect your GE Appliances hood
1. On your smart phone or tablet visit
www.GEAppliances.com/connect to learn more about
connected appliance features and to download the
appropriate app.
2. Follow the app onscreen instructions to connect your
GE Appliances hood.
3. Once the process is complete, the connection light
located on your GE Appliances hood display will stay
on solid and the app will confirm you are connected.
4. If the connection light does not turn on or is blinking,
follow the instructions on the app to reconnect. If
issues continue please call 800.220.6899 and ask for
assistance regarding hood wireless connectivity.
To connect additional smart devices, repeat steps 1 and 2.
Note that any changes or modifications to the remote
enable device installed on this hood that are not
expressly approved by the manufacturer could void the
user’s authority to operate the equipment.
* Compatible Apple or Android devices and home Wi-Fi network required.
6 49-80795-1
Filters
Be sure the circuit breaker is off and all surfaces are cool before cleaning or servicing any part of the vent hood.
Metal Grease Filter
The metal filters trap grease during cooking.
The filters must ALWAYS be in place when the hood
is in use. The grease filters are dishwasher-safe and
should be cleaned every month, depending on the
usage of the hood.
To remove:
Open the filter cover panel and disengage the filter lock
to release the filter.
To replace:
Fit the tabs at the bottom of the filter into the slots in the
back of the filter opening. Lift up the front side of the filter
and push gently until the filter locks into place. Make sure
the filter lock is in the closed position to secure the filter.
NOTE: The front panel covers the filters and must be
pressed up and then pulled down to access the filters.
To clean:
Swish the filter in hot soapy water and rinse in clean
water or wash it in the dishwasher. Do not use abrasive
cleansers.
NOTE: Some discoloration of the filter may occur in the
dishwasher.
CARE AND CLEANING: Filters
Charcoal Filter (for recirculation installation only)
If the model is not vented to the outside, the air needs to
be recirculated through a disposable charcoal filter that
helps remove smoke and odors.
NOTE: DO NOT rinse, or put charcoal filter in an
automatic dishwasher.
The charcoal filter is included with the unit. It cannot
be cleaned, It must be replaced when Reset Filter
LED indicator comes on. It is recommended that the
charcoal filter be replaced every 6 months or if it is
noticeably dirty or discolored.
Order Charcoal Filter UXCF91
To inquire about purchasing replacement charcoal filters
or to find the location of a dealer nearest you, please call
our toll-free number:
National Parts Center 800.626.2002
To install:
1. Remove the metal filters—see Metal Grease Filter
section.
2. Install the charcoal filter mounts to either side of the
motor using three screws per side.
3. Insert the tab on the charcoal filter into the triangular
slot on the mount.
4. Clip the charcoal filter in until it is locked.
5. Repeat with second filter on the other side of the motor.
6. Replace the metal filters - See Metal Grease Filter section.
To remove:
1. Remove the metal filters—see Metal grease filter
section.
2. Unclip the charcoal filter by pressing the release clip.
3. Carefully remove charcoal filter from tab.
Charcoal
Filter Mount
49-80795-1 7
Surfaces
Stainless Steel Surfaces (on some models)
Do not use a steel wool pad; it will scratch the
surface.
To clean the stainless steel surface, use warm sudsy
water or a stainless steel cleaner or polish. Always wipe
the surface in the direction of the brush line. Follow
the cleaner instructions for cleaning the stainless steel
surface. Cleaners with oxalic acid such as Bar Keepers
Friend Soft Cleanser™ will
remove surface rust, tarnish, and
small blemishes. To receive a
coupon for a trial sample of Bar
Keepers Friend Soft Cleanser™
follow the link below or scan the
QR Code.
www.barkeepersfriend.com/ge
Painted Surfaces and Black Stainless Color (on some models)
Do not use a steel wool pads or other abrasive
cleaners; they will scratch the surface.
Clean grease-laden surfaces of the hood frequently. To
clean the hood surface, use a hot, damp cloth with a
mild detergent suitable for painted surfaces. About one
tablespoon of ammonia may be added to the water. Use
a clean, hot, damp cloth to remove soap. Dry with a dry,
clean cloth.
CARE AND CLEANING: Surfaces / Lights
Use only a liquid cleanser free of grit and rub in the
direction of the brush lines with a damp soft sponge.
To inquire about purchasing stainless steel appliance
cleaner or polish, or to find the location of a dealer
nearest you, please call our toll-free number:
National Parts Center
800.626.2002
GEApplianceParts.com
NOTE: When cleaning, take care not to come in contact
with filters and other surfaces.
CAUTION
be certain that you do not touch the light with moist
hands or cloth. A warm or hot light may break if
touched with a moist surface. Always let the light
cool completely before cleaning around it.
When cleaning the hood surfaces,
Lights
CAUTION
1. Before attempting to replace the lights, make sure that
the light switch is turned off.
2. Rotate light counterclockwise to unlock and pull out.
Wearing latex gloves may offer a better grip.
3. Replace with new light of same type, making sure
pins are inserted properly into the sockets of the lamp
holder and turn clockwise to lock.
All lamps need to be GU10 compatible.
Allow lights to cool before touching.
Lamp
Holder
Rotate the lamp until the
pins are located in narrow
neck of the socket to lock.
8 49-80795-1
INSTALLATION INSTRUCTIONS
Installation
Wall Hoods
UVW9301, UVW9361
Instructions
“If you have questions, call GE Appliances at 800.GE.CARES (800.432.2737)
or visit our website at: GEAppliances.com”
BEFORE YOU BEGIN
Read these instructions completely and carefully.
Ŷ
IMPORTANT — Save these
instructions for local inspector’s use.
Ŷ
IMPORTANT — Observe all governing
codes and ordinances.
Ŷ
Note to Installer – Be sure to leave these
instructions with the Consumer.
Ŷ
Note to Consumer – Keep these instructions for
future reference.
Ŷ
Skill level – Installation of this vent hood requires
basic mechanical and electrical skills.
Ŷ
Completion time – Approximately 1 to 3 hours
Ŷ
Proper installation is the responsibility of the
installer.
Ŷ
Product failure due to improper installation is not
covered under the Warranty.
CAUTION
these vent hoods and to reduce the risk of personal
injury or damage to the product, TWO PEOPLE
ARE REQUIRED FOR PROPER INSTALLATION.
Due to the weight and size of
WARNING
ELECTRIC SHOCK OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
A. Installation work and electrical wiring must be
done by qualified person(s) in accordance with
all applicable codes and standards, including
fire-rated construction.
B. Sufficient air is needed for proper combustion
and exhausting of gases through the flue
(chimney) of fuel burning equipment to prevent
back drafting. Follow the heating equipment
manufacturer’s guidelines and safety standards
such as those published by the National Fire
Protection Association (NFPA), the American
Society for Heating, Refrigeration and Air
Conditioning Engineers (ASHRAE) and the local
code authorities.
C. When cutting or drilling into wall or ceiling, do
not damage electrical wiring and other hidden
utilities.
D. Ducted fans must always be vented to the
outdoors.
E. Turn off breaker to adjacent rooms while
working.
WARNING
USE ONLY METAL DUCT WORK.
TO REDUCE THE RISK OF FIRE,
TO REDUCE THE RISK OF FIRE,
FOR YOUR SAFETY
WARNING
WARNING
switch power off at service panel and lock the
service disconnecting means to prevent power from
being switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag,
to the service panel.
49-80795-1 9
Before beginning the installation,
at the main circuit breaker or fuse box before
installing.
Disconnect all electrical power
Installation Preparation
PRODUCT DIMENSIONS
12-1/4Ǝ
4-5/8Ǝ
25-3/4Ǝ
13-13/16Ǝ
2-3/4Ǝ
INSTALLATION PREPARATION
Filter Cover Panel
30ƎRUƎ
8Ǝ
12-1/8Ǝ
6-15/16Ǝ
10-5/8Ǝ
26-5/8Ǝ min. - 50-7/8Ǝ max.
20Ǝ
20Ǝ
INSTALLATION CLEARANCES
These vent hoods are designed to be installed onto
a wall with no above cabinets.
24” Required Min.
36” Recommended Max.
The vent hood must be installed between the 24”
required minimum and 36” recommended maximum
above the cooking surface. For supplied duct cover
ceiling heights, see Installation Height Table.
NOTE: Installation height should be measured from
the cooking surface to the lowest part of the hood.
The hood must be installed onto a wall. It can be
vented to the outdoors, or it can be installed for
recirculating operation. For recirculation operation,
see Recirculation Install Planning.
30ƎRUƎ
10 49-80795-1
Installation Preparation
INSTALLATION PREPARATION
TOOLS AND MATERIALS REQUIRED
(NOT SUPPLIED)
Safety glasses
Pencil and tape measure
Phillips screwdriver
Level
Wire cutter/stripper
Electric drill with #2 Phillips
and 1/8" drill bits
UL listed wire nuts
8" round duct
(length will vary)
Aluminized
duct tape
Strain relief for
junction box
Gloves
REMOVE THE PACKAGING
PLAN THE INSTALLATION
CAUTION
properly exhaust air, be sure to duct the air outside.
Do not vent exhaust air into spaces within walls or
ceilings or into attics, crawl spaces, or garages.
PARTS SUPPLIED FOR INSTALLATION
Ŷ 1 Hardware Package
Ŷ 1 Literature Package
Ŷ Recirculation Duct (for recirculation install only)
Ŷ Charcoal filters (recirculation mode)
PARTS NEEDED FOR INSTALLATION
Ŷ 1 Strain Relief
Ŷ 1 Wall or Roof Cap (for ducted venting only)
Ŷ All Metal Ductwork (for ducted venting only)
WARNING
PERSONAL INJURY HAZARD
Because of the weight and size of the rangehood
canopy. It is recommended that 2 people are used
to install the range hood. Failure to properly lift
rangehood could result in damage to the product or
personal injury.
NOTE: This rangehood can be installed as either
ducted or recirculation. In a ducted application,
this rangehood can be vented through the wall
or ceiling. When installed for recirculation, the
rangehood vents out the sides of the duct cover.
NOTE: Before making any cuts or holes for
installation, determine which venting method will be
used and carefully calculate all measurements.
To reduce risk of fire and to
CAUTION
sharp edges.
Ŷ Remove the duct covers.
Ŷ Remove the hardware bag, literature package
and other boxed parts.
Ŷ Remove and properly discard the protective
plastic wrapping and other packaging materials.
49-80795-1 11
Wear gloves to protect against
Installation Preparation
RANGE HOOD COMPONENTS
A. Wall Hood
B. Upper Duct Cover
C. Lower Duct Cover
D. Mounting Screws
E. Duct Cover
Mounting Bracket
F. Damper
J
B
INSTALLATION PREPARATION
C
J
G. Hood Mounting
Bracket
H. Mounting Anchors
J. Machine Screws
K. Recirculation Box
L. Wood Screws
H
J
J
F
E
D
K
INSTALLATION DIMENSIONS
The Wall Hoods duct covers can be adjusted for
different ceiling heights depending on the distance
between the bottom of the hood and the cooktop
(distance X). See Installation Height Table.
Upper Duct
7/8Ǝ min
25-1/8Ǝ max
25-3/4Ǝ
2-3/4Ǝ
X
36”
X = Distance From Hood To
(Varies depending on installation)
Recommended Max - 36”
manufacturer’s recommendation
Cover
Required Min & Recommended
Max Ceiling Height Examples
Lower
Duct Cover
Hood Body
Cooktop
Required Min - 24”,
Also consult cooktop
Typical Range
X = 24" X = 36"
Min Min
7' 6" 9' 6"
Max Max
8' 6" 10' 5"
Required Min Ceiling
Height for Recirculation
X = 24" X = 36"
Min Min
7' 10" 8' 10"
For higher ceiling
installations up to
12', use the 12' High
Ceiling Duct Cover
kit (UX12DC93) for
your model.
For higher ceiling
installations up to
14', use the 14' High
Ceiling Duct Cover
kit (UX14DC93) for
your model.
J
L
D
A
J
H
H
G
L
D
RECIRCULATION COMPONENTS
K
HARDWARE COMPONENTS
NOTE: The chimney extension replaces the upper
and lower chimney shipped with the range hood.
The hardware included with the hood should be
saved and also used with the chimney extension.
L
Phillips Head
Wood Screw
3/16" x 1-15/16"
(QTY: 4)
Mounting Anchors
H
(QTY: 6)
E
Phillips Head
Mounting Anchors
Screws
3/16" x 1-1/2"
(QTY: 6)
J
Phillips Head
Machine Screw
1/8" x 3/8"
(QTY: 14)
D
12 49-80795-1
Installation Preparation
INSTALLATION PREPARATION
INSTALLATION HEIGHT TABLE
(UX12DC93SS or
UX12DC93TS)
Optional High Ceiling Duct Cover
Installation Height with Supplied Duct Covers
Possible Vented
Ceiling
Height (ft./in.)
7' 6" 24 24 9' 3" 24 12' 24-36
7' 7" 24-25 24-25 9' 4" 24-25 12' 1" 24-36
7' 8" 24-26 24-26 9' 5" 24-26 12' 2" 24-36
7' 9" 24-27 24-27 9' 6" 24-27 12' 3" 24-36
7' 10" 24-28 24-28 24 9' 7" 24-28 12' 4" 24-36
7' 11" 24-29 24-29 24-25 9' 8" 24-29 12' 5" 24-36
8' 24-30 24-30 24-26 9' 9" 24-30 12' 6" 24-36
8' 1" 24-31 24-31 24-27 9' 10" 24-31 12' 7" 24-36
8' 2" 24-32 24-32 24-28 9' 11" 24-32 12' 8" 24-36
8' 3" 24-33 24-33 24-29 10' 24-33 12' 9" 24-36
8' 4" 24-34 24-34 24-30 10' 1" 24-34 12' 10" 24-36
8' 5" 24-35 24-35 24-31 10' 2" 24-35 12' 11" 24-36
8' 6" 24-36 24-36 24-32 10' 3" 24-36 13' 24-36
8' 7" 24-36 24-36 24-33 10' 4" 24-36 13' 1" 25-36
8' 8" 24-36 24-36 24-34 10'5"-11'3" 24-36 13' 2" 26-36
8' 9" 24-36 24-36 24-35 11' 4" 24-36 13' 3" 27-36
8' 10" 24-36 24-36 24-36 11'5" 24-36 13' 4" 28-36
8' 11" 24-36 24-36 24-36 11'6" 24-36 13' 5" 29-36
9' 24-36 24-36 24-36 11'7" 24-36 13' 6" 30-36
9' 1" 24-36 24-36 24-36 11'8" 25-36 13' 7" 31-36
9' 2" 24-36 25-36 24-36 11'9" 26-36 13' 8" 32-36
9' 3" 24-36 26-36 24-36 11'10" 27-36 13' 9" 33-36
9' 4" 24-36 27-36 24-36 11' 11" 28-36 13' 10" 34-36
9' 5" 24-36 28-36 24-36 12' 29-36 13' 11" 35-36
9' 6" 25-36 29-36 25-36 14' 36
9' 7" 26-36 30-36 26-36
9' 8" 27-36 31-36 27-36
9' 9" 28-36 32-36 28-36
9' 10" 29-36 33-36 29-36
9' 11" 30-36 34-36 30-36
10' 31-36 35-36 31-36
10' 1" 32-36 36 32-36
10' 2" 33-36 33-36
10' 3" 34-36 34-36
10' 4" 35-36 35-36
10' 5" 36 36
Possible Vented
Install Height
(in.)
Install Height
(Recirculation
vented Holes
Hidden) (in.)
Possible
Recirculation
Install
Height (in.)
Height (ft./in.)
up to 12 ft.
(not included with unit)
Ceiling
Vented and
Recirculation
Height (in.)
(UX14DC93SS or
UX14DC93TS)
Optional High Ceiling Duct Cover
up to 14 ft.
(not included with unit)
Ceiling
Height (in.)
Vented and
Recirculation
Install
Height (in.)
*Based on a 36" electric range height.
7/8Ǝ min
46-1/4Ǝ max
Upper
Duct Cover
7/8Ǝ min
29-7/16Ǝ max
For gas range, start chart at 92" and subtract 2" for the maximum install height for each block.
Upper
Duct Cover
46-7/8" 46-7/8"
Lower
Duct Cover
Lower
Duct Cover
Hood Body Hood Body
12" High Ceiling Duct Cover Kit 14" High Ceiling Duct Cover Kit
49-80795-1 13
Installation Preparation
ADVANCE PLANNING
Duct Install Planning
Ŷ This hood is designed to be vented vertically
through the ceiling. Use an 8" round duct. Use
locally supplied elbows to vent horizontally
through the rear wall.
Ŷ Use metal ductwork only.
Ŷ Determine the exact location of the vent hood.
Ŷ Plan the route for venting exhaust to the
outdoors. To maximize the ventilation
performance of the vent system:
1. Minimize the duct run length and number of
transitions and elbows.
2. Maintain a constant duct size.
3. Seal all joints with duct tape to prevent any leaks.
NOTE: Flexible vent is not recommended. Flexible
vent creates back pressure and air turbulence that
INSTALLATION PREPARATION
greatly reduces performance.
Ŷ Maximum equivalent duct length for 100 CFM:
150 foot for vent hoods.
Ŷ Install a wall cap or roof cap with damper at the
exterior opening. Purchase the wall or roof cap
and any transition and length of duct needed in
advance.
Ŷ When applicable, install any makeup (replacement)
air system in accordance with local building code
requirements. Use makeup air kit JXMUA8.
Vent system can terminate either through the roof
RUWKHZDOO7RYHQWWKURXJKDZDOODHOERZLV
needed and installed immediately above the hood.
Roof Cap
Add Insulation
and/or Caulk
Round Duct
POWER SUPPLY
IMPORTANT – (Please read carefully)
WARNING
FOR PERSONAL SAFETY, THIS APPLIANCE
MUST BE PROPERLY GROUNDED.
Remove house fuse or open circuit breaker before
beginning installation.
Do not use an extension cord or adapter plug with
this appliance. Follow National Electrical Codes or
prevailing local codes and ordinances.
Electrical supply
These vent hoods must be supplied with 120V,
60Hz, and connected to an individual, properly
grounded branch circuit, and protected by a 15 or
20 amp circuit breaker or time delay fuse.
Ŷ Wiring must be 2 wire with ground.
Ŷ If the electrical supply does not meet the above
requirements, call a licensed electrician before
proceeding.
Ŷ Route house wiring as close to the installation
location as possible in the ceiling or wall.
Ŷ Connect the wiring to the house wiring in
accordance with local codes.
Grounding instructions
The grounding conductor must be connected to
a ground metal, permanent wiring system, or an
equipment-grounding terminal or lead on the hood.
WARNING
equipment-grounding conductor can result in a risk
of electric shock. Check with a qualified electrician
or service representative if you are in doubt whether
the appliance is properly grounded.
The improper connection of the
Wall Cap
Add tape to joint
Hood
Recirculation Install Planning
A recirculation duct (included) and charcoal
filter (included) are necessary for recirculation
installation.
Power Supply Planning
The location of the power supply connection is called
out in the Installing The Hood Bracket Mount section.
Add Insulation
and/or Caulk
14 49-80795-1
Installation
NEW CONSTRUCTION, PRE-PLANNING, OR REMODELING
NOTE: For existing construction, skip to the section, Installing The Hood Bracket Mount.
Ŷ Install horizontal wood supports between 2 wall
studs that align with the vertical mounting height
locations shown in the illustration.
Ŷ The horizontal supports must be flush with the room
side studs.
Ŷ For ducted installation, the hole for the duct in the
ceiling must be centered 5" away from the finished
rear wall.
From the lower left corner of
the gray shaded area, it is
recommended to have at least
20" of house electrical wiring.
5"
Ŷ The bottom support aligns with the hood mounting
bracket. This height depends on the desired height
of the hood.
Ŷ The top support must be flush with the ceiling.
Ŷ The electrical wiring can be located 5-1/2” to the left
or right (junction box is on the left) of the centerline.
Must remain 7/16” above the back panel and 5” from
the ceiling, refer to illustration on next page.
INSTALLATION
Acceptable
area for
electrical
wiring
14-3/8"
11"
24-36" + 1-1/8"
See the Installation
Height Table for possible
installation heights.
* 36” or 38” Range
Wood Supports
• 36" minimum
width centered
• 4" height
* Typical electrical range is 36"
and typical gas range is 38"
5"
11"
Acceptable
area for
electrical
wiring
14-3/8"
49-80795-1 15
Loading...