General Electric PVX7300EJES Use & Care

SAFETY INFORMATION ...........3

USING THE HOOD

Controls ................................5

Chef Connect ...........................6

CARE AND CLEANING

Filters ..................................7

Surfaces ................................8

Lights ..................................8

INSTALLATION INSTRUCTIONS ..9

TROUBLESHOOTING TIPS ........ 21

WARRANTY ........................22

ACCESSORIES .....................23

CONSUMER SUPPORT ............24

OWNER’S MANUAL &

INSTALLATION INSTRUCTIONS

JVX3240 JVX3300 JVX5300 JVX5360 JVX5305 JVX5365 PVX7300 PVX7360

Write the model and serial numbers here:

Model # _________________

Serial # _________________

RANGE HOODS

You can find them on a label on the inside of the hood.

Para consultar una version en

español de este manual de

instrucciones, visite nuestro sitio de

internet GEAppliances.com.

ESPAÑOL

991.0480.237

GE is a trademark of the General Electric Company. Manufactured under trademark license.

49-80783-4 05-17 GEA

THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.

Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.

We take pride in the craftsmanship, innovation and design that goes into every GE Appliances

product, and we think you will too. Among other things, registration of your appliance ensures that we

can deliver important product information and warranty details when you need them.

Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration

card included in the packing material.

2 49-80783-4

IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING

SAFETY INFORMATION

WARNING

ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

A. Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the manufacturer.

B. Before servicing or cleaning unit, switch power off

at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

C. Do not use this unit with any solid-state speed

control device.

D. This unit must be grounded.

WARNING

RANGE TOP GREASE FIRE:

A. Never leave surface units unattended at high

settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on medium settings.

B. Always turn hood ON when cooking at high heat or

when flambéing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flanbé).

C. Clean ventilating fans frequently. Grease should not

be allowed to accumulate on fan or filter.

D. Use proper pan size. Always use cookware

appropriate for the size of the surface element.

TO REDUCE THE RISK OF FIRE,

TO REDUCE THE RISK OF A

WARNING

TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:

A. SMOTHER FLAMES with a close-fitting lid, cookie

sheet or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

B. NEVER PICK UP A FLAMING PAN—You may be

burned.

C. DO NOT USE WATER, including wet dishcloths or

towels—a violent steam explosion will result.

D. Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate it.

2. The fire is small and contained in the area where it started.

3. The fire department is being called.

4. You can fight the fire with your back to an exit.

* Based on “Kitchen Fire Safety” published by NFPA.

CAUTION

ONLY. DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS AND VAPORS.

TO REDUCE THE RISK OF INJURY

FOR GENERAL VENTILATING USE

READ AND SAVE THESE INSTRUCTIONS

49-80783-4 3

IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING

REMOTE ENABLE EQUIPMENT (on some models)

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The wireless communication equipment installed on this hood has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to:

(a) provide reasonable protection against harmful interference in a residential installation. This

SAFETY INFORMATION

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Ŷ5HRULHQWRUUHORFDWHWKHUHFHLYLQJDQWHQQD Ŷ,QFUHDVHWKHVHSDUDWLRQEHWZHHQWKHHTXLSPHQWDQG

receiver.

Ŷ&RQQHFWWKHHTXLSPHQWLQWRDQRXWOHWRQDFLUFXLW

different from that to which the receiver is connected.

Ŷ&RQVXOWWKHGHDOHURUDQH[SHULHQFHGUDGLR79

technician for help.

(b) accept any interference received, including interference that may cause undesired operation of the device.

Note that any changes or modifications to the wireless communication device installed on this oven that are not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

How to Remove Protective Shipping Film and Packaging Tape

Carefully grasp a corner of the protective shipping film with your fingers and slowly peel it from the appliance surface. Do not use any sharp items to remove the film. Remove all of the film before using the appliance for the first time.

To assure no damage is done to the finish of the product, the safest way to remove the adhesive from packaging tape on new appliances is an application of a household liquid dishwashing detergent. Apply with a soft cloth and allow to soak.

NOTE: The adhesive must be removed from all parts.

READ AND SAVE THESE INSTRUCTIONS

4 49-80783-4

Controls

On Some Models

USING THE HOOD: Controls

Light Fan

Off

1. Rangehood Control Panel: The control panel

is located on the front of the canopy.

2. Light Switch: Light switch toggles between

On and Off.

On Some Models

Off

3. Fan Power Switch: The power switch toggles

between fan settings Hi, Lo, and Off.

1. Rangehood Control Panel: The control panel

is located on the front of the canopy.

2. Light Button: 2Q1LJKW2IIVZLWFKIRUWKHOLJKWV

Press the LIGHT button to turn the lights on, again to set the lights to night setting, and again to turn off.

3. Fan Off Button: Off switch for the fan. The fan

can be operated by pressing any of the fan setting buttons. Hold for 3 seconds to activate auto off after 15 minutes.

4. Fan Settings Buttons: Speed control for

fan. Press the button Lo for LOW speed, Med for MEDIUM speed and Hi for HIGH speed. Hold down the Hi button for 3 seconds to activate the BOOST SPEED that will run for 10 minutes.

49-80783-4 5

Controls

On Some Models

1. Rangehood Control Panel: The glass touch

control panel is located on the front of the canopy.

2. Light Pad: 2Q1LJKW2IIVZLWFKIRUWKHOLJKWV

Press the LIGHT pad to turn the lights on, again to set the lights to night setting, and again to turn off.

3. Auto Off Pad: Off switch for the fan. The fan

can be operated by pressing any of the fan setting pads. Hold for 3 seconds to activate auto off after 15 minutes.

Chef Connect

4. Fan Settings Pads: Speed control for fan.

Press the pad Lo for LOW speed, Med for MEDIUM speed and Hi for HIGH speed. Hold down the Hi button for 3 seconds to activate the BOOST SPEED that will run for 10 minutes.

5. Chef Connect: This is a Bluetooth

feature for use with other compatible Chef Connect enabled products on a cooktop or a range. When the device is paired, the light and fan will turn ON at the Default Sync Settings upon receiving a command from the range or cooktop. It will remain ON at that setting until the user changes it.

pairing

Chef Connect Operation Bluetooth® Connection

To pair with another device:

USING THE HOOD: &RQWUROV&KHI&RQQHFW

To start the pairing process on the hood, press and hold the Light pad for 3 seconds. The backlight for the Lo – Med – Hi – Light will flash in that sequence until the hood is paired with the range or other device. If the pairing is successful, all 4 lights (Lo, Med, Hi, and Light) will flash three times simultaneously and then turn off.

It will time out after 2 minutes if pairing is not completed. After which the pairing sequence will need to be restarted.

To cancel pairing:

To cancel the pairing hold the Light pad for 3 seconds and then turn off the hood.

Default Sync Settings:

The factory default setting for the light will be the brightest.

The factory default setting for the fan sync will be OFF. The user can change the Default Sync Settings by

pressing and holding the Lo pad for 3 seconds. This will enter the Default Settings Mode. Once in this mode, the backlights for all buttons (Lo, Med, Hi, and Light) will

EOLQN2Q2IILQGHILQLWHO\DQGWKHIDQDQGOLJKWZLOOVZLWFK

to the current Default Sync Setting, so the user knows what the current default value is. At this time, set the light and fan to the desired default levels. Once the user is satisfied with the selection, press and hold the Off pad for 3 seconds. This will exit this mode. At that time the backlights will stop blinking and the state of the fan and light will change back to their prior state before entering the Default Settings Mode.

6 49-80783-4

Filters

Be sure the circuit breaker is off and all surfaces are cool before cleaning or servicing any part of the vent hood.

Metal Grease Filter

The metal filters trap grease during cooking. The filter must ALWAYS be in place when the hood is in

use. The grease filter is dishwasher-safe and should be cleaned every 6 months, or as needed.

To remove:

Pull downward on the filter lock to release the filter.

To replace:

Fit the tabs at the bottom of the filter into the slots in the back of the filter opening. Lift up the front side of the filter and push gently until the filter locks into place. Make sure the filter lock is in the closed position to secure the filter.

To clean, swish the filter in hot soapy water and rinse in clean water or wash it in the dishwasher. Do not use abrasive cleansers.

NOTE: Some discoloration may occur in the dishwasher.

NOTE: For this

configuration one grease filter is only used in the vented mode.

CARE AND CLEANING: Filters

Charcoal Filter (for recirculation installation only)

If the model is not vented to the outside, the air needs to be recirculated through a disposable charcoal filter that helps remove smoke and odors.

NOTE: DO NOT rinse, or put charcoal filter in an automatic dishwasher.

The charcoal filter cannot be cleaned. It must be replaced. It is recommended that the charcoal filter be replaced every 6-12 months or if it is noticeably dirty or discolored.

To inquire about purchasing replacement charcoal filters or to find the location of a dealer nearest you, please visit GEApplianceParts.com

NOTE: For this configuration charcoal filter is installed in place of grease filter.

To install (on some models):

1. Remove the metal filters—see Metal Grease Filter section.

2. Place the side of the charcoal filter with the tabs against the bottom of the blower.

3. Drive screws in the 2 locations shown in the picture.

4. Replace the metal filters—see Metal Grease Filter section.

To remove:

1. Remove the metal filters—see Metal Grease Filter section.

2. Remove the 2 screws holding the charcoal filter in place to remove.

Charcoal filter included on models:

JVX3240 and JVX3300

49-80783-4 7

Charcoal filter not included on this model.

Visit GEAppliances.com to order.

Surfaces

Stainless Steel Surfaces (on some models)

Do not use a steel wool pad; it will scratch the surface.

To clean the stainless steel surface, use warm sudsy water or a stainless steel cleaner or polish. Always wipe the surface in the direction of the brush line. Follow the cleaner instructions for cleaning the stainless steel surface. Cleaners with oxalic acid such as Bar Keepers Friend Soft Cleanser™ will remove surface rust, tarnish, and small blemishes. To receive a $2.00 coupon for a trial sample of Bar Keepers Friend Soft Cleanser™ follow the link below or scan the QR Code.

www.barkeepersfriend.com/ge

Painted Surfaces (on some models)

Do not use a steel wool pads or other abrasive cleaners; they will scratch the surface.

Clean grease-laden surfaces of the hood frequently. To clean the hood surface, use a hot, damp cloth with a mild detergent suitable for painted surfaces. About one tablespoon of ammonia may be added to the water. Use a clean, hot, damp cloth to remove soap. Dry with a dry, clean cloth.

CARE AND CLEANING:6XUIDFHV/LJKWV

Lights

Use only a liquid cleanser free of grit and rub in the direction of the brush lines with a damp soft sponge.

To inquire about purchasing stainless steel appliance cleaner or polish, or to find the location of a dealer nearest you, please visit GEApplianceParts.com

NOTE: When cleaning, take care not to come in contact with filters and other surfaces.

CAUTION

be certain that you do not touch the light with moist hands or cloth. A warm or hot light may break if touched with a moist surface. Always let the light cool completely before cleaning around it.

When cleaning the hood surfaces,

CAUTION

Allow lights to cool before touching.

On Some Models

1. Before attempting to replace the lights, make sure that the light switch is turned off.

2. Remove light cover.

3. Unscrew light counterclockwise to unlock light and pull out.

4. Replace with new light of same type (standard incandescent), making sure socket is properly inserted into the housing of the lamp holder.

On Some Models

1. Before attempting to replace the lights, make sure that the light switch is turned off.

2. Rotate light counterclockwise to unlock and pull out. Wearing latex gloves may offer a better grip.

3. Replace with new light of same type, making sure pins are inserted properly into the sockets of the lamp holder and turn clockwise to lock.

All lamps need to be GU10 compatible.

Light Cover

Sockets

Lamp Holder

Rotate the lamp until the pins are located in narrow neck of the socket.

8 49-80783-4

INSTALLATION INSTRUCTIONS

Installation

Under the Cabinet (UTC) Hoods

JVX3240, JVX3300, JVX5300, JVX5360, JVX5305,

Instructions

“If you have questions, call GE Appliances at 800.GE.CARES (800.432.2737)

or visit our website at: GEAppliances.com”

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT — Save these

instructions for local inspector’s use.

•

IMPORTANT — Observe all governing

codes and ordinances.

• Note to Installer – Be sure to leave these instructions with the Consumer.

• Note to Consumer – Keep these instructions for future reference.

• Skill level – Installation of this vent hood requires basic mechanical and electrical skills.

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not covered under the Warranty.

JVX5365, PVX7300, PVX7360

WARNING

ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

A. Installation work and electrical wiring must be

done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.

B. Sufficient air is needed for proper combustion

and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guidelines and safety standards such as those published by the National Fire Protection Association (NFPA), the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

C. When cutting or drilling into wall or ceiling, do

not damage electrical wiring and other hidden utilities.

D. Ducted fans must always be vented to the

outdoors.

TO REDUCE THE RISK OF FIRE,

FOR YOUR SAFETY

WARNING

switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

Before beginning the installation,

WARNING

USE ONLY METAL DUCT WORK.

WARNING

at the main circuit breaker or fuse box before installing.

TO REDUCE THE RISK OF FIRE,

Disconnect all electrical power

CAUTION

properly exhaust air, be sure to duct air outside. Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces or garages.

49-80783-4 9

To reduce risk of fire and to

Installation Preparation

DUCTWORK REQUIREMENTS

WARNING

NOTE: Read the ductwork sections only if you do not have existing ductwork. If you have existing ductwork, skip to the “Damage” section and proceed.

The venting system must exhaust to the outside. This hood can be vented vertically through upper cabinets or horizontally through an outside wall. Ductwork is

not included.

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

Exhaust connection

This hood is designed to be vented vertically using a 7" round duct or a 3 1»4” x 10” rectangular duct or horizontally using a 3 1»4” x 10” rectangular duct.

Duct length

The ducting from this fan to the outside of the building has a strong effect on the air flow, noise and energy use of the fan. Use the shortest, straightest duct routing possible for best performance, and avoid installing the fan with smaller ducts than recommended. Insulation around the ducts can reduce energy loss and inhibit mold growth. Fans installed with existing ducts may not achieve their rated air flow.

NOTE: For an ENERGY STAR

INSTALLATION PREPARATION

Also, for these models do not use less than 7” diameter duct.

model, unit must be vented mode to be considered ENERGY STAR® certified.

INSULATION AND/OR CAULK AROUND THE DUCTS

Add Insulation

DQGRU&DXON

Add tape to joint

Hood

Roof Cap

Round or Rectangular Duct

Cabinet

Wall Cap

Add Insulation

DQGRU&DXON

10 49-80783-4

Installation Preparation

INSTALLATION PREPARATION

PRODUCT DIMENSIONS

5 1»2”

Size X

24” 23 30” 29 15»16” 36” 35 15»16”

ø 7”

12”

X20”

*Controls may vary

»16”

MOUNTING SPACE

Bottom edge

of cabinet

needs to

be 30” or

more from

the cooking

surface

34"-36" Typical

ƎƎRUƎ to match cooktop width

24" Min required 30" Max recommended to the bottom of the hood

4”

»4”

5”7 1»2”

3 1»4”

»2”

NOTES:

• Hood width may be greater than the width of the

Top View

range or cooktop, but it may not be smaller.

• Installation height should be measured from the cooking surface to the lowest part of the hood.

5”7 1»2”

»4”

This hood must be installed onto a cabinet. It can be vented to the outdoors, or it can be installed for recirculating operation.

Back View

49-80783-4 11

Installation Preparation

TOOLS AND MATERIALS REQUIRED (NOT SUPPLIED)

Pencil and tape measure

Spirit level

Electric drill, #2 Phillips,

flat head, and 9»32" drill bit

INSTALLATION PREPARATION

Torx 10, 15, 20 driver

Safety glasses

:LUHFXWWHUVWULSSHU

UL listed wire nuts

Strain relief for

junction box

PLAN THE INSTALLATION

CAUTION

properly exhaust air, be sure to duct the air outside – Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages.

To reduce risk of fire and to

PARTS SUPPLIED FOR INSTALLATION

• 1 Hardware Package

• 1 Literature Package

• 1 Vented Mode Deflector Part

PARTS NEEDED FOR INSTALLATION

• 1 Strain Relief

• Power Supply Cable

• 1 Wall or Roof Cap (for external venting only)

• All Metal Ductwork (for external venting only) NOTE: This range hood can be installed as either

ducted or recirculation. In a ducted application, this range hood can be vented through the wall or ceiling. When installed for recirculation, the range hood vents out the front of the hood.

NOTE: Before making any cuts or holes for installation, determine which venting method will be used and carefully calculate all measurements.

Aluminized

Charcoal Filter (required for some

models in recirculation mode)

Duct tape

REMOVE THE PACKAGING

CAUTION

sharp edges.

• Remove the hardware bag, literature package and other boxed parts.

• Remove and properly discard the protective plastic wrapping and other packaging materials.

Wear gloves to protect against

12 49-80783-4

Installation Preparation

INSTALLATION PREPARATION

RANGE HOOD COMPONENTS

A. Hood Body B. 'DPSHU'XFW&RQQHFWRU C. Mounting Bracket D. Screws (4) E. Screws (4) F. Screws (6)

For vented mode only

INSTALLATION DIMENSIONS

12"

34"-36" Typical

X = Distance from hood to cooktop

(varies depending on installation) Required Min. = 24" Recommended Max. = 30"

HARDWARE COMPONENTS

DE F

The hood is designed to fit 12" deep cabinets. For 15" deep cabinets, filler panel kits are available from GEApplianceParts.com:

JXS50SS for 30" wide hoods JXS56SS for 36" wide hoods

49-80783-4 13

Installation Preparation

ADVANCE PLANNING

Vented Install Planning

• This hood is designed to be vented vertically using a 7" round duct or a 3 1»4" x 10" rectangular duct or horizontally using a 3

• Use metal ductwork only.

• Determine the exact location of the vent hood.

• Plan the route for venting exhaust to the outdoors. To maximize the ventilation performance of the vent system:

1. Minimize the duct run length and number of transitions and elbows.

2. Maintain a constant duct size.

3. Seal all joints with duct tape to prevent any leaks.

4. Do not use any type of flexible ducting.

• Install a wall cap or roof cap at the exterior

INSTALLATION PREPARATION

opening. Purchase the wall or roof cap and any transition and length of duct needed in advance.

• When applicable, install any makeup (replacement) air system in accordance with local building code requirements. Visit GEAppliances.com for available makeup air solutions.

Recirculation Install Planning

This hood may be installed in recirculation mode and is shipped in this configuration. The charcoal filter is necessary for recirculation installation.

This part may need to be ordered separately depending on model.

Power Supply Planning

The location of the power supply connection is called out in the Prepare for Electrical and Venting section on page 15.

»4" x 10" rectangular duct.

POWER SUPPLY

IMPORTANT – (Please read carefully)

WARNING

FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.

Remove house fuse or open circuit breaker before beginning installation.

Do not use an extension cord or adapter plug with this appliance. Follow National Electrical Codes or prevailing local codes and ordinances.

Electrical supply

These vent hoods must be supplied with 120V, 60Hz, and connected to an individual, properly grounded branch circuit, and protected by a 15 or 20 amp circuit breaker or time delay fuse.

• Wiring must be 2 wire with ground.

• If the electrical supply does not meet the above requirements, call a licensed electrician before proceeding.

• Route house wiring as close to the installation location as possible in the ceiling or wall.

• Connect the wiring to the house wiring in accordance with local codes.

Grounding instructions

The grounding conductor must be connected to a ground metal, permanent wiring system, or an equipment-grounding terminal or lead on the hood.

WARNING

equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded.

The improper connection of the

14 49-80783-4

Installation Preparation

INSTALLATION PREPARATION

SELECT VENT OPTION THAT

YOUR INSTALLATION WILL REQUIRE (A-D)

Outside top exhaust

(Vertical duct—3 1»4” x 10” Rectangular)

Outside top exhaust

(Vertical duct—7” Round)

PREPARING MOUNTING

For cabinets with dimensions below, the

mounting bracket may be used for any model. Otherwise, the hood must mount directly to bottom of cabinet. Wood shims may be needed for cabinets with a recessed bottom. Skip to step B.

Cabinet X

24” 22 30” 28 1»2”

»4" Depth

To install the mounting bracket

Drive (E) screws in partway into mounting

bracket. The bracket labeled "R" will be used on the right side of the cabinet and the bracket labeled "L" will be used on the left side of the cabinet.

36” 34 1»2”

»2”

Outside rear exhaust

(Horizontal duct—3 1»4” x 10” Rectangular)

Recirculating

(Unit is configured from factory in this mode)

Under the cabinet that you are placing the

range hood, attach the mounting bracket as shown below with (F) screws. Make sure orientation is correct. Brackets should be located against the back wall and flush with the bottom of the cabinet.

Flush with

Push

against

wall

cabinet

NOTE: Repeat on left side.

49-80783-4 15

+ 33 hidden pages