General Electric PVM9005FMDS Installation

尺寸:770*505mm

NOTE: IT IS VERY IMPORTANT TO READ
AND FOLLOW THE DIRECTIONS IN THE
INSTALLATION INSTRUCTIONS BEFORE
PROCEEDING WITH THIS REAR WALL
TEMPLATE.
CUT WALL TEMPLATE FROM TOP CABINET
TEMPLATE ALONG WITH THE DASHED
CUTTINGLINE. REFER TO

A.

This template is for locating the horizontal exhaust
cutout. Do not use this template for vertical or
recirculation exhaust.

CUT ALONG THIS LINE

(

3/8″″ TO EDGE

12″

)

F. CUT OUT FOR HORIZONTAL

4″

OUTSIDE EXHAUST

B.

LINE UP WITH
PREVIOUSLY
DRILLED HOLE.

CUT ALONG THIS LINE

1.Place the template flat against the rear wall, aligning
the circles A. and B. with the corresponding holes
previously drilled in the rear wall for holes A. and B.
of the wall plate.

2.With the template aligned to the holes. tape the
template to the rear wall.

3.Use a saber or keyhole saw to cut out the shaded
area F. through the rear wall.

4.Remove the template from the rear wall.

5.RETURN TO AND PROCEED WITH THE

INSTALLATION INSTRUCTIONS

Printed in China PN: 261800313994

CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR

REAR WALL TEMPLATE

30

CAUTION– IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE

RECOMMENDED DIMENSION，GREASE-LADEN AIR WILL

DISCHARGE INTO HOUSE STRUCTURE.

″ MINIMUM WIDTH REQUIRED

CUT ALONG THIS LINE CUT ALONG THIS LINE

LINE UP WITH
PREVIOUSLY
DRILLED HOLE.

Publish No: 31-41080

1

AREA

BLOCK

FILLER

A.

F.

DRILL

3/8＂

DIAMETER 3/8＂

NOTE: IT IS VERY IMPORTANT TO READ AND FOLLOW THE DIRECTIONS IN
THE INSTALLATION INSTRUCTIONS BEFORE PROCEEDING WITH THIS TOP
CABINET TEMPLATE.

This template is used to locate the power cord clearance hole, cabinet mounting holes, and the vertical
exhaust cutout.

1. Determine if your cabinet has a recessed area (Fig. 1) or a smooth, flat bottom (Fig. 3). If smooth, tape
template onto the bottom surface (Fig. 4) and proceed to Step 3.

13-3/8＂

8-1/4＂

TOP CABINET TOP CABINET TOP CABINET TOP CABINET TOP CABINET

NOTE: IT IS VERY IMPORTANT TO READ AND FOLLOW THE DIRECTIONS IN THE INSTALLATION
INSTRUCTIONS BEFORE PROCEEDING WITH THIS TOP CABINET TEMPLATE.
This template is used to locate the power cord clearance hole, cabinet mounting holes, and the vertical

exhaust cutout.

FIGURE 1

Recessed
Bottom
Cabinet

1. Determine if your cabinet has a recessed area (Fig. 1) or a smooth, flat bottom (Fig. 3). If smooth, tape
template onto the bottom surface (Fig. 4) and proceed to Step 3.

2. If it is recessed, cut the edges of the template to fit in the recessed bottom of the cabinet. It is
important that the edges of the cabinets permit level installation of the oven. Follow directions below
for cutting and mounting:

RECOMMENDED CUTTING PROCEDURE
Measure cabinet thickness of the sides A & C and the back B. Cut the edge of the template to

allow for cabinet thickness (guideline is marked in 1⁄4″ increments for your convenience).

NOTE: On some cabinets a small bracket or glue block is used between the overhang and the
underside of the cabinet bottom. Cut the template to fit around the bracket or glue block so
that template will lie flat against the bottom of the cabinet.

Tape the Top Cabinet Template to the underside of the top cabinet in the recessed area. (Fig. 2)
NOTE: Make sure the rear of the template touches the back wall (for smooth, flat bottom cabinets) or
the back of the recess (for recessed bottom cabinets) after cutting the edges of the template.

3. Drill 3/8″ diameter holes at A., B. & C.

CAUTION: Wear safety goggles when drilling holes in the cabinet bottom.

4. Cut out the 2″ diameter hole at D for power cord. If cabinets are metal, use the nylon grommet (see

the Parts Included section in the Installation Instructions) to surround the opening to protect the cord.

5. FOR VERTICAL EXHAUST ONLY. (Skip for horizontal exhaust or recirculation exhaust.)
Cut out shaded area labeled E. in the cabinet bottom for Vertical (Outside) Exhaust location.

6. Remove the top cabinet template.

7. For recessed cabinets, make 2 filler blocks out of scrap wood the size of the shaded areas F. & G.

These filler blocks must have a thickness equal to the depth of the cabinet recess. Drill 3/8″ diameter

holes in these blocks to line up with A. & C. Place the blocks so that the holes in each block line up with
the corresponding holes in the cabinet. The filler blocks should be at the same level as the bottom edge
of the wall cabinet frame (Fig. 5).

8. Return to and proceed with the Installation Instructions.

FIGURE 2 FIGURE 3 FIGURE 4

Recessed
Bottom
Cabinet
With
Template

Smooth
Flat Bottom
Cabinet

NOTE: IT IS VERY IMPORTANT TO READ AND FOLLOW THE DIRECTIONS IN THE INSTALLATION
INSTRUCTIONS BEFORE PROCEEDING WITH THIS TOP CABINET TEMPLATE.
This template is used to locate the power cord clearance hole, cabinet mounting holes, and the vertical

exhaust cutout.

1. Determine if your cabinet has a recessed area (Fig. 1) or a smooth, flat bottom (Fig. 3). If smooth, tape
template onto the bottom surface (Fig. 4) and proceed to Step 3.

2. If it is recessed, cut the edges of the template to fit in the recessed bottom of the cabinet. It is
important that the edges of the cabinets permit level installation of the oven. Follow directions below
for cutting and mounting:

RECOMMENDED CUTTING PROCEDURE
Measure cabinet thickness of the sides A & C and the back B. Cut the edge of the template to

allow for cabinet thickness (guideline is marked in 1⁄4″ increments for your convenience).

NOTE: On some cabinets a small bracket or glue block is used between the overhang and the
underside of the cabinet bottom. Cut the template to fit around the bracket or glue block so
that template will lie flat against the bottom of the cabinet.

Tape the Top Cabinet Template to the underside of the top cabinet in the recessed area. (Fig. 2)
NOTE: Make sure the rear of the template touches the back wall (for smooth, flat bottom cabinets) or
the back of the recess (for recessed bottom cabinets) after cutting the edges of the template.

3. Drill 3/8″ diameter holes at A., B. & C.

CAUTION: Wear safety goggles when drilling holes in the cabinet bottom.

4. Cut out the 2″ diameter hole at D for power cord. If cabinets are metal, use the nylon grommet (see

the Parts Included section in the Installation Instructions) to surround the opening to protect the cord.

5. FOR VERTICAL EXHAUST ONLY. (Skip for horizontal exhaust or recirculation exhaust.)
Cut out shaded area labeled E. in the cabinet bottom for Vertical (Outside) Exhaust location.

6. Remove the top cabinet template.

7. For recessed cabinets, make 2 filler blocks out of scrap wood the size of the shaded areas F. & G.

These filler blocks must have a thickness equal to the depth of the cabinet recess. Drill 3/8″ diameter

holes in these blocks to line up with A. & C. Place the blocks so that the holes in each block line up with
the corresponding holes in the cabinet. The filler blocks should be at the same level as the bottom edge
of the wall cabinet frame (Fig. 5).

8. Return to and proceed with the Installation Instructions.

10 1/2” (26.67cm)

must be maintained

to rea wall

Smooth
Flat Bottom
Cabinet
With
Template

FILLER BLOCKS

FIGURE 5

13-3/8＂

B.

3/8＂

DRILL
DIAMETER 3/8＂

C.

DRILL

3/8＂

DIAMETER 3/8＂

G.

AREA

BLOCK

FILLER

1/4’’

1/2’’

1’’

2. If it is recessed, cut the edges of the template to fit in the recessed bottom of the cabinet. It is
important that the edges of the cabinets permit level installation of the oven. Follow directions below
for cutting and mounting:

RECOMMENDED CUTTING PROCEDURE
Measure cabinet thickness of the sides A & C and the back B. Cut the edge of the template to

allow for cabinet thickness (guideline is marked in 1⁄4″ increments for your convenience).

NOTE: On some cabinets a small bracket or glue block is used between the overhang and the
underside of the cabinet bottom. Cut the template to fit around the bracket or glue block so
that template will lie flat against the bottom of the cabinet.
Tape the Top Cabinet Template to the underside of the top cabinet in the recessed area. (Fig. 2)

NOTE: Make sure the rear of the template touches the back wall (for smooth, flat bottom cabinets) or
the back of the recess (for recessed bottom cabinets) after cutting the edges of the template.

3. Drill 3/8″ diameter holes at A., B. & C.

CAUTION: Wear safety goggles when drilling holes in the cabinet bottom.

4. Cut out the 2″ diameter hole at D for power cord. If cabinets are metal, use the nylon grommet (see

the Parts Included section in the Installation Instructions) to surround the opening to protect the cord.

5. FOR VERTICAL EXHAUST ONLY. (Skip for horizontal exhaust or recirculation exhaust.)
Cut out shaded area labeled E. in the cabinet bottom for Vertical (Outside) Exhaust location.

6. Remove the top cabinet template.

7. For recessed cabinets, make 2 filler blocks out of scrap wood the size of the shaded areas F. & G.

These filler blocks must have a thickness equal to the depth of the cabinet recess. Drill 3/8″ diameter

holes in these blocks to line up with A. & C. Place the blocks so that the holes in each block line up with
the corresponding holes in the cabinet. The filler blocks should be at the same level as the bottom edge
of the wall cabinet frame (Fig. 5).

8. Return to and proceed with the Installation Instructions.

TOP CABINET TEMPLATE

D.

2＂

E. CUT OUT FOR VERTICAL (OUTSIDE)

EXHAUST ONLY

＂2/1-4

CUT HOLE THROUGH CARBINET BOTTOM FOR EXHAUST ADAPTOR

6-1/4＂

12-1/2＂

DRILL
DIAMETER 2＂

＂4/1-4

＂23/72-9

Publish No: 31-41080

1/4’’

1/2’’

1’’

1/4’’

1/2’’

1’’

WALL WALL