GENERAL ELECTRIC PSJC5YGXWV, PSHS6YGXSS, PSHS6TGXSS, PSHS6RGXSS, PSFW3YGXSS User Manual
...
ge.com
Refrigerators
Profile Side-by-Side
200D8074P018 49-60573 09-08 JR
La section française commence à la page 46
La sección en español empieza en la página 88
Safety Instructions . . . . . . . . . . .2–4
Operating Instructions
Automatic Icemaker . . . . . . . . . . . . . . .14
Care and Cleaning . . . . . . . . . . . . .16, 17
ClimateKeeper2
™
. . . . . . . . . . . . . . . . . . . .6
Crispers and Pans . . . . . . . . . . . . . . . . .13
CustomCool
™
. . . . . . . . . . . . . . . . . . . . .7, 8
Ice and Water Dispenser . . . . . . .15, 16
QuickFreeze
™
. . . . . . . . . . . . . . . . . . . . . . .9
Quick Ice . . . . . . . . . . . . . . . . . . . . . . . . . .15
Refrigerator Doors . . . . . . . . . . . . . . . . .12
Replacing the Light Bulbs . . . . . . . . . .18
Set Features . . . . . . . . . . . . . . . . . . . . . . . .6
Shelves and Bins . . . . . . . . . . . . . . .10, 11
Temperature Controls . . . . . . . . . . . . . . .5
TurboCool
™
. . . . . . . . . . . . . . . . . . . . . . . . .6
Water Filter . . . . . . . . . . . . . . . . . . . . . . . . .9
Installation Instructions
Installing the Refrigerator . . . . . . .28–31
Moving the Refrigerator . . . . . . . .24–27
Preparing to Install
the Refrigerator . . . . . . . . . . . . . . . . . . . .23
Trim Kits and Panels . . . . . . . . . . . .19–22
Water Line Installation . . . . . . . . .32–34
Troubleshooting Tips . . . . . .36–38
Normal Operating Sounds . . . . . . . . . .35
Consumer Support
Consumer Support . . . . . . . .Back Cover
Performance Data Sheet . . . . . . . . . . .41
Product Registration . . . . . . . . . . . .43, 44
State of California Water
Treatment Device Certificate . . . . . . .42
Warranty (Canadian) . . . . . . . . . . . . . . .39
Warranty (U.S.) . . . . . . . . . . . . . . . . . . . .40
Réfrigérateurs
Profile Côte à Côte
Refrigeradores
Profile Lado a Lado
Models 23, 25, 26, 27 and 29
Write the model and serial numbers
here:
Model # __________________________
Serial # __________________________
Find these numbers on a label inside
the refrigerator compartment at the
top on the right side.
Owner’s Manual
and Installation
Manuel d’utilisation
et d’installation
Manual del propietario
e instalación
Consumer Support
Troubleshooting Tips
Operating Instructions
Safety Instructions
Installation
Instructions
2
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
Use this appliance only for its intended purpose as described in this Owner’s Manual.
SAFETY PRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including the following:
■
■ This refrigerator must be properly installed
and located in accordance with the Installation
Instructions before it is used.
■
■ Do not allow children to climb, stand or hang
on the shelves in the refrigerator. They could
damage the refrigerator and seriously injure
themselves.
■
■ Do not touch the cold surfaces in the freezer
compartment when hands are damp or wet.
Skin may stick to these extremely cold surfaces.
■
■ Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
■
■ In refrigerators with automatic icemakers,
avoid contact with the moving parts of the ejector
mechanism, or with the heating element located
on the bottom of the icemaker. Do not place fingers
or hands on the automatic icemaking mechanism
while the refrigerator is plugged in.
■
■ Keep fingers out of the “pinch point” areas;
clearances between the doors and between
the doors and cabinet are necessarily small.
Be careful closing doors when children are
in the area.
■
■ Unplug the refrigerator before cleaning and making
repairs.
NOTE: We strongly recommend that any servicing
be performed by a qualified individual.
■
■ Non-LCD models: Setting either or both controls
to OFF does not remove power to the light circuit.
■
■ LCD models: Turning the cooling system off does
not remove power to the light circuit.
■
■ Do not refreeze frozen foods which have thawed
completely.
■
■ Always clean the CustomCool™Tray after thawing
food.
Consumer Support
Troubleshooting Tips
Operating InstructionsSafety Instructions
Installation
Instructions
ge.com
PROPER DISPOSAL OF THE REFRIGERATOR
Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are
still dangerous…even if they will sit for “just a few
days.” If you are getting rid of your old refrigerator,
please follow the instructions below to help prevent
accidents.
Before You Throw Away Your Old
Refrigerator or Freezer:
■ Take off the doors.
■ Leave the shelves in place so that children may not
easily climb inside.
Refrigerants
All refrigeration products contain refrigerants,
which under federal law must be removed prior
to product disposal. If you are getting rid of an
old refrigeration product, check with the company
handling the disposal about what to do.
USE OF EXTENSION CORDS
Because of potential safety hazards under certain conditions, we strongly recommend against the use
of an extension cord.
However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United States)
or a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding type plug and
outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.
DANGER! RISK OF CHILD ENTRAPMENT
3
4
Consumer Support
Troubleshooting Tips
Operating Instructions
Safety Instructions
Installation
Instructions
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
For personal safety, this appliance must be properly grounded.
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding) wall outlet
to minimize the possibility of electric shock hazard
from this appliance.
Have the wall outlet and circuit checked by
a qualified electrician to make sure the outlet
is properly grounded.
If the outlet is a standard 2-prong outlet, it is your
personal responsibility and obligation to have it
replaced with a properly grounded 3-prong wall
outlet.
The refrigerator should always be plugged into its
own individual electrical outlet which has a voltage
rating that matches the rating plate.
This provides the best performance and also prevents
overloading house wiring circuits which could cause
a fire hazard from overheated wires.
Never unplug your refrigerator by pulling on
the power cord. Always grip plug firmly and pull
straight out from the outlet.
Repair or replace immediately all power cords
that have become frayed or otherwise damaged.
Do not use a cord that shows cracks or abrasion
damage along its length or at either end.
When moving the refrigerator away from the wall,
be careful not to roll over or damage the power cord.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
Consumer Support
Troubleshooting Tips
Operating Instructions
Safety Instructions
Installation
Instructions
About the temperature controls. ge.com
NOTE: The refrigerator is shipped with protective film covering the temperature controls. If this film was not
removed during installation, remove it now.
The temperature controls are preset in the factory at 37°F (3°C)
for the refrigerator compartment and 0°F (-18°C) for the freezer
compartment. Allow 24 hours for the temperature to stabilize
to the preset recommended settings.
Refrigerator temperatures can be adjusted between 34°F and 46°F
(1°C to 8°C), and the freezer temperatures can be adjusted between
–6°F and 8°F (–21°C to –13°C).
To change the Refrigerator temperature:
LCD Models:
Access By: Home > Refrigerator
Activate By: Using the arrows to select the desired
temperature. You must press ENTER to set the new
temperature.
To change the Freezer temperature:
Access By: Home > Freezer
Activate By: Using the arrows to select the desired
temperature. You must press ENTER to set the new
temperature.
Once the desired temperature has been set, the display will
return to the HOME screen and show the set temperatures
underneath the actual temperature display for several
seconds. Several adjustments may be required. Each time you
adjust the controls, allow 24 hours for the refrigerator to reach
the temperature you have set.
Non-LCD Models:
To change the temperature, press and release the FREEZER
TEMP/FRIDGE TEMP pad. The SET light will come on and
the display will show the set temperature. To change the
temperature, tap either the or pad until the desired
temperature is displayed.
Once the desired temperature has been set, the temperature
display will return to the actual refrigerator and freezer
temperatures after 5 seconds. Several adjustments may be
required. Each time you adjust the controls, allow 24 hours
for the refrigerator to reach the temperature you have set.
The temperature controls can display both the SET temperature
as well as the actual temperature in the refrigerator and freezer.
The actual temperature may vary slightly from the SET temperature
based on usage and operating environment.
Turning the cooling system off:
LCD models: Turning the cooling system OFF stops cooling in both
the freezer and refrigerator compartments, but does not shut off
electrical power to the refrigerator.
LCD Models:
Access By: Home > Options > Information and Settings >
Cooling System Off
To turn the cooling system back on, press the touch screen
and press the ON button.
Activate By: Pressing ENTER.
Non-LCD Models:
Press and release the FREEZER TEMP/FRIDGE TEMP pad.
Press to set freezer temperature to 5. The display will
show OFF. To turn the unit back on, press the FREEZER
TEMP/FRIDGE TEMP pad. Press to set the freezer and
refrigerator temperatures to the preset points of 0°F (-18°C)
for the freezer and 37°F (3°C) for the refrigerator.
When the unit is turned back on, it will take up to 24 hours
to stabilize.
The Performance Air Flow System is designed
to maximize temperature control in the refrigerator and
freezer compartments. This unique special feature consists
of the Air Tower along the back wall of the refrigerator and
the Air Tunnel on the bottom portion of the freezer rear wall.
Placing food in front of the louvers on these components will
not affect performance. Although the Air Tower and the Air
Tunnel can be removed, doing so will affect temperature
performance. (For removal instructions, on-line, contact
us at ge.com or call 800.GE.CARES. In Canada, contact us
at GEAppliances.ca or call 1.800.561.3344.)
Performance Air Flow System
5
LCD models
Non-LCD models
Not all features are on all models. Your controls will look like one of the following:
>
>
>
>
6
About TurboCool.
™
How it Works
TurboCool™rapidly cools the refrigerator
compartment in order to more quickly
cool foods. Use TurboCool when adding
a large amount of food to the refrigerator
compartment, putting away foods after they
have been sitting out at room temperature or
when putting away warm leftovers. It can
also be used if the refrigerator has been
without power for an extended period.
Once activated, the compressor will turn
on immediately and the fans will cycle on
and off at high speed as needed for eight
hours. The compressor will continue to run
until the refrigerator compartment cools
to approximately 34°F (1°C), then it will cycle
on and off to maintain this setting. After
8 hours, or if TurboCool is pressed again,
the refrigerator compartment will return
to the original setting.
How to Use
LCD Models:
Access By: Home > Options > Refrigerator
Options > TurboCool
Activate By: Pressing ON.
Deactivate By: Pressing OFF.
Non-LCD Models:
Press SET FEATURES. The refrigerator
temperature display will show TurboCool
and/or TC. Press ON/OFF.
After TurboCool is complete, the refrigerator
compartment will return to the original
setting.
NOTES:
The refrigerator temperature cannot be
changed during TurboCool.
The freezer temperature is not affected during
TurboCool.
When opening the refrigerator door during
TurboCool, the fans will continue to run if they
have cycled on.
Consumer Support
Troubleshooting Tips
Operating Instructions
Safety Instructions
Installation
Instructions
About ClimateKeeper2.
™
(on some models)
How it Works
The ClimateKeeper2™is the industry’s
most advanced refrigeration system,
delivering optimum temperature and
humidity performance to keep food garden
fresh longer and reduce freezer burn, while
maintaining E star-level efficiency.
The ClimateKeeper2 system features two
evaporators—one for the refrigerator and
one for the freezer.
This provides two separate cooling systems,
and separates the airflow between the fresh
food and freezer compartments during
normal cooling operations.*
This ensures that the humidity levels in
the fresh food compartment are significantly
higher than in a conventional system,**
allowing fresh produce and other unsealed
foods to retain their moisture content and
freshness longer. Moisture sensitive foods
such as fresh fruit, salads, rice, etc., can now
be stored on open shelves without excessive
moisture loss. Due to the higher humidity in
the refrigerator, you may on occasion
experience fog or small amounts of moisture
in the refrigerator compartment. This is
normal and may come and go as different
food loads and environmental conditions
change. Wipe dry with a paper towel if
desired.
The separate airflow system minimizes
the mixing of air between the two
compartments, which reduces fresh food
odor transfer to improve the taste of ice.
The ClimateKeeper2 system also reduces
the number of defrosting cycles in the freezer
evaporator, thereby reducing freezer burn.
*Freezer air is used in the CustomCool
feature.
**Testing shows a higher level of humidity in
the Fresh Food section in ClimateKeeper2
refrigerators versus conventional units.
About Set Features.
This pad is used to select the following
features: TurboCool, Quick Ice, Door Alarm
and Water Filter.
Pressing SET FEATURES repeatedly will cycle
through all of the available features and then
exit the mode. If no key is pressed, the mode
will exit and return to displaying features
currently set.
LCD Models Only
7
Empty the pan. Place the Chill/Thaw tray
in the pan. Place the items on the tray
and close the pan completely.
LCD Models:
Access by: Home > Options >
Refrigerator Options > CustomCool Pan
Non-LCD Models:
Select the ExpressThaw™, ExpressChill
™
or SelectTemp™pad. The display and SET
light will come on. Tap the pad until the
light appears next to the desired setting.
Use the following chart to determine the
best setting to use.
■ ExpressChill can be set to 15, 30 or 45
minutes. The default is 15 minutes.
■ To stop a feature before it is finished:
For LCD Models:
Go into that feature’s menu and press
the OFF button.
For Non-LCD Models:
Tap that feature’s pad until no options
are selected and the display is off.
■ During ExpressThaw and
ExpressChill,the display on the
controls will count down the time
in the cycle (on some models).
■ After the ExpressThaw cycle is
complete, the pan will reset to the
MEAT setting (32°F [0°C]) to help
preserve thawed items until they
are used.
■ The displayed actual temperature of
the CustomCool pan may vary slightly
from the SET temperature based on
usage and operating environment.
NOTE: For food safety reasons, it is
recommended that foods be wrapped in
plastic wrap when using ExpressThaw.
This will help contain meat juices and improve
thawing performance.
About CustomCool™. (on some models) ge.com
The CustomCool
™
feature is used to quickly
chill items, thaw items or hold the pan at a
specific temperature. This feature is a system
of dampers, a fan, a temperature thermistor
and a heater.
The pan is tightly sealed to prevent
temperature fluctuations in the rest of
the refrigerator. The controls for this pan
are located on the dispenser with the
temperature controls.
How to Use
ExpressThaw
™
To remove:
Pull the drawer out to the stop position.
Rotate all four swing locks to the unlock
position.
Lift the front of the drawer up and out.
To replace:
Make sure all four swing locks are in
the unlock position.
Place the sides of the drawer into
the drawer supports, making sure
the swing locks fit on the drawer slots.
Lock all four swing locks by rotating them
to the lock position.
How to Remove and Replace the Drawer
ExpressChill
™
Consumer Support
Troubleshooting Tips
Operating Instructions
Safety Instructions
Installation
Instructions
Non-LCD Models Only
How it Works
LCD Models OnlyOR
REFRIGERATOR OPTIONS
CUSTOM COOL
PAN
BEVERAGE
CENTER
BACK
TURBOCOOL
8
About CustomCool™. (on some models)
CustomCool™Chart
NOTE: Results may vary depending on packaging, starting temperature and other food traits.
ExpressThaw
™
0.5 Lb. (4 hours)
■ Hamburger Patties (0.5 lb)
■ Individually Wrapped
Filet Mignon (0.5 lb)
1.0 Lb. (6 hours)
■ Chicken Breasts (1.0 lb)
■ Ground Beef (1.0 lb)
■ Steak (1.0 lb)
2.0 Lbs. (10 hour
s)
■ Chicken Breasts (2.0 lbs)
■ Ground Beef (2.0 lbs)
■ Steak (2.0 lbs)
3.0 Lbs. (12 hours)
■ Chicken Breasts (3.0 lbs)
■ Ground Beef (3.0 lbs)
■ Steak (3.0 lbs)
ExpressChill
™
15 Minutes
■ 1 Beverage Can (12 oz)
■ 2 Small Juice Boxes (6–8 oz each)
30 Minutes
■ 2 to 6 Beverage Cans (12 oz each)
■ 2 Plastic 20 oz Bottles of Beverage
■ 4 to 6 Small Juice Boxes
(6–8 oz each)
■ 3 Foil Juice Packets
■ Wine (750 ml bottle)
45 Minutes
■ 2 Liter of Beverage
■ 1/2 Gallon of Juice
■ Gelatin–1 package
SelectTemp
™
Citrus Setting (43°F [6°C])
■ Oranges, Lemons, Limes, Pineapple,
Cantaloupe
■ Beans, Cucumbers, Tomatoes,
Peppers, Eggplant, Squash
Produce Setting (35°F [2°C])
■ Strawberries, Raspberries, Kiwifruit,
Pears, Cherries, Blackberries, Grapes,
Plums, Nectarines, Apples
■ Asparagus, Broccoli, Corn,
Mushrooms, Spinach, Cauliflower,
Kale, Green Onion, Beets, Onions
Meat Setting (32°F [0°C])
■ Raw Meat, Fish and Poultry
Consumer Support
Troubleshooting Tips
Operating Instructions
Safety Instructions
Installation
Instructions
Some CustomCool models feature a
beverage center. It is designed to store
beverages at colder temperatures. Select
this feature if you like to keep extra-chilled
refreshments on hand.
Access by: Home > Options > Refrigerator
Options > Beverage Center
Activate by: Pressing ON.
Deactivate by: Pressing OFF.
How to Use the Beverage Center (LCD models only)
To remove:
Remove dairy bin first. Holding
the bottom of the dairy bin, lift the front
straight up, then lift up and out.
Holding left and right side of beverage
center, lift straight up and out.
Leave adapter in place.
To replace:
Engage backside of beverage center in
molded supports on adapter. Then push
down on the sides of the beverage center.
The beverage center will lock into place.
Replace dairy bin.
How to Remove and Replace the Beverage Center (LCD models only)
Dairy Bin
Adapter
Beverage
Center
About QuickFreeze.
™
(on some models) ge.com
The QuickFreeze plate is only to be
used with the QuickFreeze feature.
Use QuickFreeze to freeze items faster
to enhance food preservation.
How to Use
Place food (wrapped in plastic wrap)
on QuickFreeze plate. Turn the feature
on via the LCD controls.
Some LCD Models Only:
Access By: Home > Options > Freezer Options
> QuickFreeze
Activate By: Using the arrows to select
the time and pressing Enter.
Deactivate By: Pressing OFF.
NOTE: While the QuickFreeze feature is
enabled, the actual freezer temperature may
drop as low as –3°F (–19°C). This is normal.
Consumer Support
Troubleshooting Tips
Operating Instructions
Safety Instructions
Installation
Instructions
About the water filter.
Water Filter Cartridge
The water filter cartridge is located in
the back upper right corner of the refrigerator
compartment.
When to Replace the Filter
LCD Models:
A pop-up screen will appear on the LCD screen
to remind you to replace the water filter. You can
check the status of the water filter manually.
Access By: Home > Options > Dispenser Options >
Reset Water Filter
Non-LCD Models:
There is a replacement indicator light for the water
filter cartridge on the dispenser. This light will turn
orange to tell you that you need to replace the
filter soon.
The filter cartridge should be replaced when the
replacement indicator light turns red or if the flow
of water to the dispenser or icemaker decreases.
Removing the Filter Cartridge
If you are replacing the cartridge, first remove
the old one by slowly turning it to the left. Do not
pull down on the cartridge. A small amount of
water may drip down.
Installing the Filter Cartridge
There is an adapter attached to the top
of the new filter cartridge.
The adapter must be removed before
installing the cartridge. To remove the
adapter, turn it to the left about 1/4 turn.
Fill the replacement cartridge with water
from the tap to allow for better flow from
the dispenser immediately after installation.
Line up the arrow on the cartridge and
the cartridge holder. Place the top of the new
cartridge up inside the holder. Do not push
it up into the holder.
Slowly turn it to the right until the filter
cartridge stops. DO NOT OVERTIGHTEN.
As you turn the cartridge, it will automatically
raise itself into position. The cartridge will
rotate about 1/2 turn.
Run water from the dispenser for 5 minutes
to clear the system and prevent sputtering.
LCD Models:
Press FILTER REPLACED button to confirm
replacement.
Non-LCD Models:
Press the SET FEATURES pad until REPLACE
WATER FILTER is lit. Press and hold the
ON/OFF pad for 3 seconds. WATER FILTER
IS RESET will show in the window.
NOTE: A newly installed water filter cartridge may
cause water to spurt from the dispenser.
Filter Bypass Plug
You must use the filter bypass plug when a
replacement filter cartridge is not available.
The dispenser and the icemaker will not operate
without the filter or filter bypass plug.
Replacement Filters:
To order additional filter cartridges in the United
States, visit our Website, ge.com, or call GE Parts
and Accessories, 800.626.2002.
Filter Model MSWF
Customers in Canada should consult the yellow
pages for the nearest Mabe Service Center.
Place the top of the cartridge up inside
the cartridge holder and slowly turn it
to the right.
QuickFreeze Plate
Filter
Bypass
Plug
SmartWater
Cartridge
Holder
9
Consumer Support
Troubleshooting Tips
Operating Instructions
Safety Instructions
Installation
Instructions
10
About the shelves and bins.
Refrigerator Door Bins and Freezer Door Tilt-Out Bins
Bins
The larger refrigerator door bins and freezer
tilt-out door bins are adjustable.
To remove: Lift the front of the bin straight
up, then lift up and out.
To replace or relocate: Engage the back side
of the bin in the molded supports on the door.
Then push down on the front of the bin.
Bin will lock in place.
The snugger helps prevent tipping, spilling or
sliding of small items stored on the door shelf.
Place a finger on either side of the snugger
near the rear and move it back and forth
to fit your needs.
Top Freezer Bins
Not all features are on all models.
Refrigerator bin
Freezer tilt-out bin
Snugger
QuickSpace™Shelf
This shelf splits in half and slides under itself
for storage of tall items on the shelf below.
This shelf can be removed and replaced
or relocated just like Slide-Out Spillproof
Shelves.
On some models, this shelf cannot be used
in the lowest position.
Slide-Out Spillproof Shelf
The slide-out spillproof shelf allows you to
reach items stored behind others. The special
edges are designed to help prevent spills
from dripping to lower shelves.
To remove:
Slide the shelf out until it reaches
the stop, then press down on the tab
and slide the shelf straight out.
To replace or relocate:
Line the shelf up with the supports and slide
it into place. The shelf can be repositioned
when the door is at 90° or more. To reposition
the shelf, slide the shelf past the stops and
angle downward. Slide shelf down to the
desired position, line up with the supports
and slide into place.
Make sure you push the shelves all the way
back in before you close the door.
Press tab and pull shelf forward
to remove
Top freezer bin
Do not block
CAUTION:
Be careful when placing
items in the top bin.
Make sure that items
do not block or fall into
the ice chute.
Top freezer bin (on some models)
Do not block
CAUTION:
Part must be in place
as shown for proper ice
dispensing. Food cannot
be stored in this location.
ge.com
Not all features are on all models.
Slide-Out Freezer Shelves
To remove, slide out to the stop position,
lift the front past the stop position and
slide out.
Make sure you push the shelves all the way
back in before you close the door.
Freezer Baskets
To remove, push the basket all the way to
the back of the freezer. Lift up until the back
pins are disengaged. Lift the entire basket up
and pull out.
Make sure you push the baskets all
the way back in before you close the door.
Fixed Freezer Shelves
There are two types of fixed
freezer shelves.
To remove this type of shelf:
Lift the shelf up at the left side.
Bring the shelf out.
To remove this type of shelf:
Lift up the left side of the shelf and slide it
left into the center of the shelf supports.
Rotate the right side of the shelf up
and out of the shelf supports.
NOTE FOR DISPENSER MODELS: In order to
take full advantage of the tilt-out ice bin, only
store items on the shelf below the ice bin that
are no taller than the lowest point on the bin.
Consumer Support
Troubleshooting Tips
Operating InstructionsSafety Instructions
Installation
Instructions
Door Wine/Beverage Rack (on some models)
This rack holds up to 5 cans or one bottle
of wine.
The rack hangs from the sides of the
dairy bin.
To remove:
Empty the wine/beverage rack.
Holding the bottom of the dairy bin,
lift the front straight up, then lift up
and out.
To detach the rack from the dairy bin,
pull the rack’s side wires out of the holes
on each side of the dairy bin.
To replace:
Reattach the rack to the sides
of the bin.
Engage the back side of the bin in
the molded supports on the door.
Then push down on the front of the bin.
The bin will lock into place.
11
Consumer Support
Troubleshooting Tips
Operating Instructions
Safety Instructions
Installation
Instructions
12
About the refrigerator doors.
Refrigerator Doors
The refrigerator doors may feel different than
the ones you are used to. The special door
opening/closing feature makes sure the
doors close all the way and are securely
sealed.
When opening and closing the door, you will
notice a stop position. If the door is opened
past this stop point, the door will remain
open to allow you to load and unload food
more easily. When the door is only partially
open, it will automatically close.
The resistance you feel at the stop
position will be reduced as the door
is loaded with food.
When the door is only partially open,
it will automatically close.
Beyond this stop the door will stay open.
Door Alignment
If doors are uneven, adjust the refrigerator
door.
Using a 7/16″ wrench, turn the door
adjusting screw to the right to raise
the door, to the left to lower it. (A nylon
plug, imbedded in the threads of the pin,
prevents the pin from turning unless
a wrench is used.)
After one or two turns of the wrench,
open and close the refrigerator door
and check the alignment at the top
of the doors.
7/16″ Wrench
Raise
Support Leg (on some models)
Before moving the refrigerator, you will
need to screw up the support leg. Once
the unit is relocated, you will need to screw
down the support leg again.
Screw down the support
leg until it touches the
floor. This will prevent
door misalignment.
About the crispers and pans. ge.com
13
About crisper removal.
Not all features are on all models.
Crisper Removal
Crispers can easily be removed by pulling
the drawer straight out and lifting the drawer
up and over the stop location.
If the door prevents you from taking out
the drawers, first try to remove the door bins.
If this does not offer enough clearance,
the refrigerator will need to be rolled forward
until the door opens enough to slide the
drawers out. In some cases, when you roll
the refrigerator out, you will need to move
the refrigerator to the left or right as you
roll it out.
Not all features are on all models.
Fruit and Vegetable Crispers
Excess water that may accumulate in
the bottom of the drawers should be
wiped dry.
On some models, the bottom drawer has
full extension slides that allow full access
to the drawer.
Adjustable Humidity Crispers
Slide the control all the way to the HI setting
to provide high humidity recommended for
most vegetables.
Slide the control all the way to the LO
setting to provide lower humidity levels
recommended for most fruits.
HI LO
Convertible Deli Pan
The convertible deli pan has its own cold
air duct to allow a stream of cold air from
the freezer compartment or fresh food
compartment to flow to the pan.
The variable temperature control regulates
the air flow from the Climate Keeper Air
Tower.
Set the control to the coldest setting to store
fresh meats.
Set the control to cold to convert the pan
to normal refrigerator temperature and
provide extra vegetable storage space.
The cold air duct is turned off. Variable
settings between these extremes can
be selected.
C
O
L
D
C
O
L
D
E
S
T
Consumer Support
Troubleshooting Tips
Operating InstructionsSafety Instructions
Installation
Instructions
About the automatic icemaker.
Consumer Support
Troubleshooting Tips
Operating Instructions
Safety Instructions
Installation
Instructions
14
Automatic Icemaker
The icemaker will produce seven cubes
per cycle—approximately 100–130 cubes
in a 24-hour period, depending on freezer
compartment temperature, room
temperature, number of door openings
and other use conditions.
If the refrigerator is operated before the
water connection is made to the icemaker,
set the power switch in the OFF position.
When the refrigerator has been connected
to the water supply, set the power switch to
the ON position.
The icemaker will fill with water when it cools
to 15°F (–10°C). A newly installed refrigerator
may take 12 to 24 hours to begin making ice
cubes.
You will hear a buzzing sound each time
the icemaker fills with water.
Throw away the first few batches of ice
to allow the water line to clear.
Be sure nothing interferes with the sweep
of the feeler arm.
When the bin fills to the level of the feeler
arm, the icemaker will stop producing ice.
It is normal for several cubes to be joined
together.
If ice is not used frequently, old ice cubes will
become cloudy, taste stale and shrink.
Special note about dispenser models:
■ Dispenser models have a tilt-out ice bin.
The bin can be tilted out as shown in
the illustrations, and it will hold itself up
while you take ice out or turn the icemaker
power switch on and off. Be sure to put the
bin back in place before closing the door.
■ To restore your ice level from an empty
bucket stage, the following steps are
recommended:
12 hours after the first batch of ice
has fallen into the bin, dispense
3 to 4 cubes.
After an additional 6 hours, dispense
3 to 4 cubes again.
These steps will restore your ice level
in the shortest amount of time.
NOTE: In homes with lower-than-average
water pressure, you may hear the icemaker
cycle multiple times when making one batch
of ice.
A newly installed refrigerator may take 12 to 24 hours to begin making ice.
Lift the bin, then pull it
forward until the bin stops.
Removing Ice Bin (dispenser models)
CAUTION:The ice bin is heavy
when full.
Set the power switch to the OFF position
before removing the bin.
When replacing the bin, be sure to press
it firmly into place. If it does not go all the
way back, remove it and rotate the drive
mechanism 1/4 turn. Then push the bin
back again.
Lower the bin to access ice
or reach the power switch.
NOTE: In order to take full advantage
of the tilt-out ice bin, only store items on
the shelf below the ice bin that are no
taller than the lowest point on the bin.
On dispenser models,
to access ice or reach
the power switch:
Lift the bin, then pull it
forward until the bin stops.
Lift and pull forward again
to remove the bin.
Rotate
Drive
Mechanism
Dispenser Models only
Icemaker
Feeler Arm
Power Switch
About the ice and water dispenser. (on some models) ge.com
To Use the Dispenser
Select CUBED, CRUSHED or WATER.
Press the glass gently against the top
of the dispenser cradle.
The spill shelf is not self-draining. To reduce water
spotting, the shelf and its grille should be cleaned
regularly.
If no water is dispensed when the refrigerator is
first installed, there may be air in the water line
system. Press the dispenser arm for at least two
minutes to remove trapped air from the water line
and to fill the water system. To flush out impurities
in the water line, throw away the first six glassfuls
of water.
CAUTION:Never put fingers or any
other objects into the ice crusher discharge
opening.
Locking the Dispenser
Press the LOCK or
LOCK CONTROLS
pad for
3 seconds to lock the dispenser and control panel.
To unlock, press and hold the pad again for
3 seconds.
Dispenser Light
The LIGHT pad turns the night light in
the dispenser on and off. The light also comes on
when the dispenser cradle is pressed. On some
models, if this light burns out, it should be replaced
with a 6-watt, 12V maximum bulb.
Door Alarm
Use Door Alarm to sound if either door is open
for more than 3 minutes. The alarm will stop
once the door is closed. For LCD models, a popup
screen will appear. The alarm can be silenced
by touching the LCD screen.
LCD Models:
Access By: Home > Options > Information and
Settings > Settings > Door Alarm
Access By: Pressing ON.
Deactivate By: Pressing OFF.
Non-LCD Models:
Press the SET FEATURES pad once and DOOR
ALARM will blink. Press ON/OFF and the door
alarm will be set and the icon will turn solid. Press
ON/OFF again to turn the alarm off.
Spill Shelf
Consumer Support
Troubleshooting Tips
Operating Instructions
Safety Instructions
Installation
Instructions
Precise Fill (on some models)
Quick Ice
This water dispenser is equipped with a feature
called “precise fill.” This feature allows you to
choose a precise amount of water (cups or
ounces) that you would like dispensed. Pints
and Liters are also available for LCD models.
LCD Models
Access By: Home > Options > Dispenser Options >
Precise Fill > Set Amount
Activate By: Using the arrow buttons to select
the desired amount. Press MORE UNITS to select
between CUPS, OUNCES, PINTS or LITERS.
Non-LCD Models
Press the PRECISE FILL CUPS/OZ pad.
The WATER pad will light and the CRUSHED
and CUBED ice pads will turn off. The last unit
used will be displayed.
Press the PRECISE FILL pad again to toggle
between cups and ounces.
If you selected OUNCES, press the or pad
to select the number of ounces you would like
to have dispensed between 2–99 ounces.
The default is 8 ounces.
If you selected CUPS, press the or pad
to select the amount you would like to have
dispensed. They are displayed as 1/4, 1/3, 1/2, 2/3
and 3/4, with the highest amount being 16 3/4
cups. The default is 1 cup.
Press the cup against the cradle and water
will begin dispensing. It will automatically stop
when the amount set has been dispensed.
The display will show the amount of water
dispensed, beep, then reset after 5 seconds.
NOTE: Do not leave the dispenser unattended
when water is being dispensed.
If you would like to stop dispensing water
before the specified amount has been
dispensed, just remove the cup from the
cradle. The display will show the amount that
has been dispensed for 5 seconds. If the cup
switch is pressed again within that time, the
dispenser will continue up to the set amount.
If not, the display will return to the set
amount.
When you need to speed up ice production, use
the Quick Ice feature. While this feature is turned on,
the freezer fan runs continuously for 48 hours, or
until the feature is turned OFF. During this period,
ice production will increase up to 40%. Models with
the integrated ice feature system require at FIRST
USE at least half an 8 oz. glass of ice to be dispensed
every 6 to 12 hours. This will help the icemaker fill
the bucket properly so that dispensing is better.
How to Use
LCD Models:
Access by: Home > Options > Freezer Options >
Quick Ice
Activate by: Pressing ON.
Deactivate by: Pressing OFF.
Non-LCD Models:
Press the SET FEATURES pad twice and QUICK ICE
will blink. Press ON/OFF to turn the feature on,
then again to turn it off.
15
>
>
>
>
Consumer Support
Troubleshooting Tips
Operating Instructions
Safety Instructions
Installation
Instructions
16
Cleaning the Outside
The dispenser drip area, beneath the grille,
should be wiped dry. Water left in this area
may leave deposits. Remove the deposits
by adding undiluted vinegar to the well. Soak
until the deposits disappear or become loose
enough to rinse away.
The dispenser cradle. Before cleaning,
lock the dispenser by pressing and holding
the LOCK or LOCK CONTROLS pad for
3 seconds. Clean with warm water and
baking soda solution—about a tablespoon
(15 ml) of baking soda to a quart (1 liter)
of water. Rinse thoroughly and wipe dry.
The door handles and trim. Clean with
a cloth dampened with soapy water.
Dry with a soft cloth.
The stainless steel panels and door handles
(on some models) can be cleaned with
a commercially available stainless steel
cleaner. A spray-on stainless steel cleaner
works best.
Do not use appliance wax or polish
on the stainless steel.
Keep the outside clean. Wipe with a
clean cloth lightly dampened with kitchen
appliance wax or mild liquid dish detergent.
Dry and polish with a clean, soft cloth.
Do not wipe the refrigerator with a soiled
dish cloth or wet towel. These may leave
a residue that can erode the paint. Do not
use scouring pads, powdered cleaners,
bleach or cleaners containing bleach
because these products can scratch
and weaken the paint finish.
Cleaning the Inside
To help prevent odors, leave an open box
of baking soda in the fresh food and freezer
compartments.
Unplug the refrigerator before cleaning.
If this is not practical, wring excess moisture
out of sponge or cloth when cleaning around
switches, lights or controls.
Use warm water and baking soda solution—
about a tablespoon (15 ml) of baking soda to
a quart (1 liter) of water. This both cleans and
neutralizes odors. Rinse and wipe dry.
Use of any cleaning solution other than
that which is recommended, especially
those that contain petroleum distillates,
can crack or damage the interior of
the refrigerator.
Avoid cleaning cold glass shelves
with hot water because the extreme
temperature difference may cause them
to break. Handle glass shelves carefully.
Bumping tempered glass can cause it
to shatter.
Do not wash any plastic refrigerator parts
in the dishwasher.
The chill/thaw tray is dishwasher safe.
Dispenser drip area.
Care and cleaning of the refrigerator.
About the ice and water dispenser. (on some models)
Important Facts About Your Dispenser
■ Do not add ice from trays or bags to
the storage drawer. It may not crush or
dispense well.
■ Avoid overfilling glass with ice and use
of narrow glasses. Backed-up ice can
jam the chute or cause the door in the
chute to freeze shut. If ice is blocking
the chute, poke it through with a
wooden spoon.
■ Beverages and foods should not be
quick-chilled in the ice storage drawer.
Cans, bottles or food packages in the
storage drawer may cause the icemaker
or auger to jam.
■ To keep dispensed ice from missing
the glass, put the glass close to, but
not touching, the dispenser opening.
■ Some crushed ice may be dispensed
even though you selected CUBED.
This happens occasionally when a few
cubes accidentally get directed to
the crusher.
■ After crushed ice is dispensed, some
water may drip from the chute.
■ Sometimes a small mound of snow
will form on the door in the ice chute.
This condition is normal and usually
occurs when you have dispensed
crushed ice repeatedly. The snow
will eventually evaporate.
17
For long vacations or absences, remove
food and unplug the refrigerator. Clean
the interior with a baking soda solution of
one tablespoon (15 ml) of baking soda to one
quart (1 liter) of water. Leave the doors open.
Set the icemaker power switch to the OFF
position and shut off the water supply to
the refrigerator.
If the temperature can drop below freezing,
have a qualified servicer drain the water
supply system to prevent serious property
damage due to flooding.
ge.com
Behind the Refrigerator
Be careful when moving the refrigerator
away from the wall. All types of floor
coverings can be damaged, particularly
cushioned coverings and those with
embossed surfaces.
Pull the refrigerator straight out and return it
to position by pushing it straight in. Moving
the refrigerator in a side direction may result
in damage to the floor covering or
refrigerator.
When pushing the refrigerator back, make
sure you don’t roll over the power cord or
icemaker supply line.
Preparing for Vacation
Preparing to Move
Secure all loose items such as shelves and
drawers by taping them securely in place
to prevent damage.
When using a hand truck to move
the refrigerator, do not rest the front or back
of the refrigerator against the hand truck.
This could damage the refrigerator. Handle
only from the sides of the refrigerator.
Be sure the refrigerator stays in an upright
position during moving.
Consumer Support
Troubleshooting Tips
Operating InstructionsSafety Instructions
Installation
Instructions
Consumer Support
Troubleshooting Tips
Operating Instructions
Safety Instructions
Installation
Instructions
18
Replacing the light bulbs.
Setting the controls to OFF does not remove power to the light circuit.
Not all features are on all models.
Refrigerator Compartment—Upper Light
Unplug the refrigerator.
The bulbs are located at the top of
the compartment, inside the light shield.
On some models, a screw at the front of
the light shield will have to be removed.
On other models, the screw is located
in the pocket located at the back of
the light shield.
To remove the light shield, on some
models, press in on the tabs on the sides
of the shield and slide forward and out.
On other models, just slide the shield
forward and out.
After replacing the bulb with an
appliance bulb of the same or lower
wattage, replace the light shield and
screws (on some models). When
replacing the light shield, make sure
that the tabs at the back of the shield
fit into the slots at the back of the light
shield housing.
Plug the refrigerator back in.
Refrigerator Compartment—Lower Light
This light is located above the top drawer.
Unplug the refrigerator.
Remove the convertible meat drawer
control knob by pulling straight out.
Lift the light shield up and pull it out.
After replacing the bulb with an
appliance bulb of the same or lower
wattage, replace the shield and
the knob.
Plug the refrigerator back in.
Freezer Compartment
Unplug the refrigerator.
Remove the shelf just above the light
shield. (The shelf will be easier to remove
if it is emptied first.) On some models, a
screw at the top of the light shield will
need to be removed.
To remove the light shield, press in
on the sides, and lift up and out.
Replace the bulb with an appliance
bulb of the same or lower wattage,
and reinstall the light shield. When
reinstalling the light shield, make sure
the top tabs snap securely into place.
Replace the screw (on some models).
Reinstall the shelf and plug
the refrigerator back in.
C
O
L
D
C
O
L
D
E
S
T
Dispenser (on some models)
Unplug the refrigerator.
The bulb is located on the dispenser
under the control panel. Remove the light
bulb by turning it counterclockwise.
Replace the bulb with a bulb of
the same size and wattage.
Plug the refrigerator back in.
Pocket
OR
Your light shield will look like one
of the following:
Refrigerator Compartment (LCD models only)
There is an LED lighting display in the top
of the refrigerator compartment in LCD
models. If this assembly needs to be
replaced, call GE Service at 1.800.432.2737
in the United States or 1.800.561.3344
in Canada.
LED Lighting
Display
Tabs
19
Trim kits and decorator panels.
Read these instructions completely and carefully.
Before You Begin
Some models are equipped with trim kits that allow you to install door panels. You can order
pre-cut black, white, bisque or stainless steel decorator panels from GE Parts and Accessories,
800.626.2002, or you can add wood panels to match your kitchen cabinets.
Panels less than 1/4″ (6 mm) thick
When installing wood panels less than 1/4″ (6 mm) thick, you need to create a filler panel, such as 1/8″ (3 mm)
cardboard, that will fit between the face of the door and the wood panel. If you are installing the pre-cut
decorator panels, pre-cut filler panels are included in the kit. The combined thickness of the decorator
or wood panel and the filler panel should be 1/4″ (6 mm).
For CustomStyle™models
3/4″ (19 mm) or Raised Panel
A raised panel design screwed or glued to a 1/4″ (6 mm) thick backing, or a 3/4″ (19 mm) routed board can
be used. The raised portion of the panel must be fabricated to permit clearances of at least 2″ (5.1 cm) from
the handle side for fingertip clearance.
Panels thicker than 1/4″ (6 mm), up to 3/4″ (19 mm) max, will require that the outer 5/16″ (8 mm) of panel
perimeter be no thicker than 1/4″ (6 mm).
Weight limitations for custom panels:
Fresh Food 38 lbs. (17 kg) max.
Freezer Door 28 lbs. (13 kg) max.
2″ (5.1 cm)
Clearance
Handle Side
Appearance
Panel
Refrigerator
Door
1/4″ (6 mm)
Thick Backing
3/4″
(19 mm)
Panels 1/4″ thick or less
Panels thicker than 1/4″ (6 mm)
1/4″ max
1/4″ (6 mm) max
3/4″ (19 mm)
5/16″ (8 mm)
Consumer Support
Troubleshooting Tips
Operating Instructions
Safety Instructions
Installation
Instructions
Consumer Support
Troubleshooting Tips
Operating Instructions
Safety Instructions
Installation
Instructions
20
Trim kits and decorator panels.
Freezer Panel
Without Dispenser
Freezer Panel
With Dispenser Fresh Food Panel
Cutout
5/16″
(8 mm)
1415⁄32″
(36.8 cm)
679⁄32″
(170.9 cm)
1/8″ (3 mm)
FRONT
177⁄8″
(45.4 cm)
1415⁄32″
(36.8 cm)
335⁄8″
(85.4 cm)
FRONT
679⁄32″
(170.9 cm)
1915⁄32″
(49.5 cm)
FRONT
23‘ Dimensions for Custom Wood Panels
The areas at the top of the panels need to be cut out of the panels.
25‘
CustomStyle™Dimensions for Custom Wood Panels
The areas at the top of the panels need to be cut out of the panels.
Cutout
1/8″ (3 mm)
Cutout
1/8″ (3 mm)
5/16″
(8 mm)
5/16″
(8 mm)
Freezer Panel
Without Dispenser
Freezer Panel
With Dispenser Fresh Food Panel
Cutout
5/16″
(8 mm)
1415⁄32″
(36.8 cm)
69″
(175.3 cm)
1/8″ (3 mm)
FRONT
17″
(43.2 cm)
1415⁄32″
(36.8 cm)
361⁄4″
(92.0 cm)
FRONT
69″
(175.3 cm)
1915⁄32″
(49.5 cm)
FRONT
Cutout
1/8″ (3 mm)
Cutout
1/8″ (3 mm)
5/16″
(8 mm)
5/16″
(8 mm)
21
Inserting the door panels.
Attach the Top Trim on the Freezer and Fresh Food Doors.
The Top Trim can be found inside the refrigerator
compartment.
With a T-20 Torxdriver, attach the Top Trim, using two
screws on each Top Trim piece, to the top of each
door. Hand tighten only. Make sure that the top of
each panel fits snugly behind the lip of the Top Trim.
Insert the Freezer Panel and Fresh Food Panel.
Carefully push the freezer panel in until it slides
into the slot behind the door handle. Push the filler
panel (required with some door panels) in behind
the decorator panel. Repeat for fresh food panel.
If your model has a dispenser, this step only
applies to the fresh food panel and top freezer panel.
Insert the Bottom Freezer Panel (on dispenser models).
Carefully push the panel in until it slides into the slot
behind the door handle. Push the filler panel (required
with some door panels) in behind the decorator panel.
Cutout
Cutout
Top Trim Screws
Top
Freezer
Panel
Bottom
Freezer
Panel
Side Trim
Side Trim
Fresh
Food
Panel
Read these instructions completely and carefully.
Consumer Support
Troubleshooting Tips
Operating InstructionsSafety Instructions
Installation
Instructions
Top Trim Screws
22
Install the Side Trim.
These pieces are tucked inside the refrigerator
door handle.
Do not remove the protective film on the outside
of the Side Trim until the Side Trim is installed.
Fit the bottom of the Side Trim under the Bottom Trim
as illustrated.
Hold the Side Trim against the front face of
the decorator panels and fit the Side Trim under
the Top Trim. Make sure the magnetically attached
Side Trim is fitted correctly and that you are satisfied
with the appearance of all the parts.
Side
Trim
Side
Trim
Bottom Trim
Top Trim
Inserting the door panels.
Consumer Support
Troubleshooting Tips
Operating Instructions
Safety Instructions
Installation
Instructions
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
•
IMPORTANT — Save these instructions
for local inspector’s use.
•
IMPORTANT — Observe all governing
codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these instructions
for future reference.
• Skill level – Installation of this appliance requires
basic mechanical skills.
• Completion time – Refrigerator Installation
30 minutes
Water Line Installation
30 minutes
• Proper installation is the responsibility of
the installer.
• Product failure due to improper installation is not
covered under the Warranty.
If the refrigerator has already been installed,
remove the base grille (see Step 2 in Moving
the Refrigerator), then skip to Step 5 in Installing
the Refrigerator.
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com
In Canada, call 1.800.561.3344 or Visit our Website at: GEAppliances.ca
Installation
Refrigerator
Instructions
Models 23, 25, 26, 27 and 29
If the refrigerator has an icemaker, it will have
to be connected to a cold water line. A GE water
supply kit (containing tubing, shut-off valve, fittings
and instructions) is available at extra cost from your
dealer, by visiting our Website at ge.com (in Canada
at GEAppliances.ca) or from Parts and Accessories,
800.626.2002 (in Canada 1.888.261.3055).
PREPARATION
WATER SUPPLY TO THE ICEMAKER
TOOLS YOU WILL NEED
23
Phillips-Head Screwdriver
3/8″ and 5/16″ Socket 1/2″ and 7/16″ Wrench
Plastic Putty Knife
1/8″ Hex Wrench
24
Installation Instructions
LOADING THE RERIGERATOR
ONTO A HAND TRUCK
Leave all tape and door pads on doors until
the refrigerator is in its final location.
To move the refrigerator, use a padded hand
truck. Center the refrigerator on the hand truck
and secure the strap around the refrigerator.
DO NOT OVERTIGHTEN THE STRAP.
1
REMOVE THE BASE GRILLE
Remove the grille by removing the two Phillipshead screws.
2
If the refrigerator must go through
any entrance that is less than 38″ wide,
the doors must be removed. Proceed
to Step 3.
DO NOT remove the handles.
If all entrances are more than 38″ wide,
skip to Installing the Refrigerator.
DISCONNECT THE WATER COUPLING
(on some models)
If the refrigerator has a water dispenser,
there is a water line from the cabinet into
the bottom hinge on the freezer door that
must be disconnected.
To disconnect, push in on the white collar
of the coupling and pull out the tubing.
3
White Collar
Bottom
Freezer
Hinge
MOVING THE REFRIGERATOR
25
Installation Instructions
DISCONNECT THE POWER COUPLING
(on some models)
If the refrigerator has a water dispenser,
there is a power line (harness) from the cabinet
into the bottom hinge on the freezer door that
must be disconnected.
To disconnect, pull apart at the coupling.
4
Bottom
Freezer
Hinge
DISCONNECT THE ELECTRICAL
CONNECTORS (on some models)
If the refrigerator has a refreshment center,
there are electrical connectors (harnesses)
from the cabinet into the bottom hinge
on the refrigerator door that must be
disconnected.
To disconnect, pull apart each connector.
5
Bottom
Refrigerator
Hinge
CLOSE THE FREEZER AND
REFRIGERATOR DOORS
6
REMOVE THE FREEZER DOOR
Remove the freezer door top hinge cover
(if equipped) by either squeezing it and pulling
it up or by prying it off with a plastic putty
knife.
Remove the two 5/16″ or 1/8″ hex head
screws, then lift the hinge straight up to free
the hinge pin.
Open the freezer door to 90.°
7
A
C
B
5/16″ or 1/8″ Hex Head
90°
26
Installation Instructions
MOVING THE REFRIGERATOR (CONT.)
REMOVE THE FREEZER DOOR (cont.)
As one person slowly lifts the freezer door up
and off the bottom hinge, the second person
should carefully guide the water line and power
line (harness) through the bottom hinge.
Set the door on a non-scratching surface with
the inside up.
7
D
E
90°
REMOVE THE REFRIGERATOR DOOR
Remove the refrigerator door top hinge cover
(if equipped) by either squeezing it and pulling
it up or by prying it off with a plastic putty
knife.
8
A
REMOVE THE REFRIGERATOR DOOR
(cont.)
Remove the two 5/16″ or 1/8″ hex head
screws, then lift the hinge straight up to free
the hinge pin.
Open the refrigerator door to 90.°
8
B
C
5/16″ or 1/8″ Hex Head
90°
27
Installation Instructions
REMOVE THE REFRIGERATOR DOOR
(cont.)
Lift the refrigerator door up and off the bottom
hinge.
If the refrigerator has a refreshment center,
one person should slowly lift the door up and
off the bottom hinge and the second person
should carefully guide the electrical lines
(harnesses) through the bottom hinge.
Set the door on a non-scratching surface with
the inside up.
8
D
E
90°
REPLACING THE DOORS
To replace the doors, simply reverse steps
3 through 8.
However, please note the following:
• When lowering the doors onto the bottom
hinges, make sure the second person
carefully guides the tube and harnesses
through the holes in the hinges.
• When connecting the water line, make sure
you insert the tubing all the way to the mark.
• Do not pinch the tubing and harnesses when
placing the doors on the bottom hinges.
• When connecting the power line and the
electrical lines (refreshment center models
only), be sure that the connectors are seated
together fully.
9
Mark
Refreshment Center Models Only
DIMENSIONS AND SPECIFICATIONS
(for 23‘ CustomStyle
™
models)
DIMENSIONS AND SPECIFICATIONS
28
Installation Instructions
INSTALLING THE REFRIGERATOR
REFRIGERATOR LOCATION
• Do not install the refrigerator where
the temperature will go below 60°F (16°C)
because it will not run often enough to maintain
proper temperatures.
• Do not install the refrigerator where
the temperature will go above 100°F (37°C)
because it will not perform properly.
• Install it on a floor strong enough to support it
fully loaded.
CLEARANCES
Allow the following clearances for ease
of installation, proper air circulation and plumbing
and electrical connections:
23‘ (33” wide),
23‘/25‘ CustomStyle
™
25‘, 26‘, 27‘, 29‘
Sides 1/8″ (4 mm) 1/8″ (4 mm)
Top 1″ (25 mm) 1″ (25 mm)
Back 1/2″ (13 mm) 1″ (25 mm)
701⁄4″ (178.4 cm)
36″
(91.4 cm)
24″ (61 cm)
24″ (61 cm)
Cabinet
Water
Electrical
3/4″ (19 mm) Airspace
(1/2″ [13 mm] Gap +
1/4″ [6 mm] Wall Plates)
25″ (63.5 cm)
Countertop
DIMENSIONS AND SPECIFICATIONS
(for 25‘ CustomStyle
™
models)
*721/4″ (183.5 cm) required for full adjustment
of mobility wheels. If cabinets installed above
refrigerator have doors that are flush to the top of
the opening for the refrigerator, then an additional
1/8″ may be required to provide clearance for
cabinet doors to open freely.
36″
(91.4 cm)
24″ (61 cm)
721⁄4″ (183.5 cm)*
29
Installation Instructions
CONNECTING THE REFRIGERATOR
TO THE HOUSE WATER LINE
(icemaker and dispenser models)
A cold water supply is required for automatic
icemaker and dispenser operation. If there
is not a cold water supply, you will need to
provide one. See Installing the Water Line
section.
NOTES:
• Before making the connection to
the refrigerator, be sure the refrigerator
power cord is not plugged into the wall outlet.
• If your refrigerator does not have a water
filter, we recommend installing one if your
water supply has sand or particles that could
clog the screen of the refrigerator’s water
valve. Install it in the water line near the
refrigerator. If using GE SmartConnect
™
Refrigerator Tubing Kit, you will need an
additional tube (WX08X10002) to connect
the filter. Do not cut plastic tube to install
filter.
If you are using copper tubing, place a
compression nut and ferrule (sleeve) onto
the end of the tubing coming from the house
cold water supply.
If you are using the GE SmartConnect
™
tubing, the nuts are already assembled
to the tubing.
If you are using copper tubing, insert
the end of the tubing into the refrigerator
connection, at the back of the refrigerator,
as far as possible. While holding the tubing,
tighten the fitting.
If you are using GE SmartConnect
™
tubing,
insert the molded end of the tubing into
the refrigerator connection, at the back of
the refrigerator, and tighten the compression
nut until it is hand tight. Then tighten one
additional turn with a wrench. Overtightening
may cause leaks.
1
A
B
Fasten the tubing into the clamp provided to
hold it in position. You may need to pry open
the clamp.
1/4″ Tubing
Tubing Clamp
1/4″
Compression Nut
Ferrule
(sleeve)
SmartConnect™Tubing
Refrigerator
Connection
C
TURN ON THE WATER SUPPLY
Turn the water on at the shut-off valve (house
water supply) and check for any leaks.
2
PLUG IN THE REFRIGERATOR
Before plugging in the refrigerator, make sure
the icemaker power switch is set to the OFF
position.
See the grounding information attached
to the power cord.
3
LEVEL THE REFRIGERATOR (cont.)
To adjust
the rollers on 23
‘/25‘
CustomStyle
™
models:
Turn the front roller
adjusting screws
clockwise to raise
the refrigerator,
counterclockwise
to lower it. Use a 3/8″
hex wrench with extension, or an adjustable
wrench.
These models also have rear adjustable rollers
so you can align the refrigerator with your
kitchen cabinets. Use a 3/8″ hex wrench with
extension to turn the screws for the rear rollers—
clockwise to raise the refrigerator,
counterclockwise to lower it.
30
Installation Instructions
INSTALLING THE REFRIGERATOR (CONT.)
PUT THE REFRIGERATOR IN PLACE
Move the refrigerator to its final location.
4 5
LEVEL THE REFRIGERATOR
The refrigerator can be leveled by adjusting
the rollers located near the bottom hinges.
Rollers have three purposes:
• Rollers adjust so the door closes easily when
opened about halfway. (Raise the front about
5/8″ [16 mm] from the floor.)
• Rollers adjust so the refrigerator is firmly
positioned on the floor and does not wobble.
• Rollers allow you to move the refrigerator
away from the wall for cleaning.
To adjust the rollers on 23‘ (33” wide), 25‘, 26‘,
27‘ and 29‘ models:
• Turn the roller
adjusting screws
clockwise to raise
the refrigerator,
counterclockwise
to lower it. Use
a 3/8″ hex socket
or wrench, or an
adjustable wrench.
5
Rollers
Roller Adjusting Screw
Roller Adjusting Screws
LEVEL THE DOORS
Adjust the refrigerator door to make the doors
even at the top.
To align:
Using a 7/16″ wrench, turn the door adjusting
screw to the right to raise the door, to the left
to lower it.
NOTE:
A nylon plug, imbedded in the threads
of the pin, prevents the pin from turning
unless a wrench is used.
After one or two turns of the wrench, open
and close the refrigerator door and check
the alignment at the top of the doors.
6
A
B
Doors should be even at top
Raise
7/16″ Wrench
Raise
Loading...