General Electric PSB1201NSS User Manual
PSB1201NSS
C
L
(Must support 130 lbs.)
2 x 4’s or
equivalent
solid floor
Suitable
bracing
to support
runners
21-5/8"
over centerline
of cabinet
1" Min. above toekick or adjust
to oven installation height
2" MIN bet ween cutouts
2-1/2" MIN between cutouts
recommended—2" MIN required
9-1/4" cutout height
28-1/2" cutout width
Junction box location
A
B
A
B
Construct Solid Bottom
MIN 3/8" Plywood Supported by
2 x 4 or 1 x 2 Runners, all Four Sides.
(Must Suppor t 150 lbs. for Advantium)
(Must Suppor t 200 lbs. for Wall Oven)
4-3/16
D
Excluding
Handle
H
W
Conduit
(46" long)
Cabinet width
(240-volt models only)
4-3/16"
23-1/2"
Cutout depth
Junction
box location
17-1/2"
Cutout height
29-25/32"
19-1/32"
21-1/2"
Excluding
Handle
Conduit
(48-1/2"
long)
B
30"
5" min.from
floor 1" min.
above toekick
A= Allow 1" overlap of oven over bottom edge of cutout, and allow
1-1/4" overlap at top edge of cutout.
B= Allow 11/16"-3/4" for overlap of oven over side edges of cutout.
Construct Solid
Bottom Min.
3/8" Plywood
Supported by
2 x 4 or 1 x 2
Runners, all
Four Sides.
(Must Support
150 lbs.)
A
4-3/16"
23-1/2"
Cutout depth
A= Allow 1" overlap of oven over bottom edge of cutout, and allow
1-1/4" overlap at top edge of cutout.
B= Allow 11/16"-3/4" for overlap of oven over side edges of cutout.
Advantium Wall Oven Dimensions (in inches)and
Cabinet Installation (in inches)
Note: Cabinets installed adjacent
to wall ovens must have an adhesion
spec of at least 194° F temperature rating.
GE Profile Advantium® 120 Volt - 30" Wall Oven
Advantium wall oven/GE Profile cooking tower dimensions and cabinet installation information (in inches)
Note: 2" minimum
between cutouts when
installed above warming
drawer or single wall oven.
Installation Information:
Before installing, consult
installation instructions
packed with product for
current dimensional data.
Note: PSB1200/1 series
Advantium can be
installed below GE/GE
Profile non-downdraft
gas and electric cooktops.
It CANNOT be installed
below induction or Monogram
(2GU3841385) gas cooktops.
Note: PSB1200/1 series Advantium
oven comes with two lower trim pieces.
One is for use above 36-inch height
installations and one is for use below 36inch installations. Use of the accessory
drawer will replace the bottom trim piece
for applicable installations. Please see
installation instructions for full details.
For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
ge.com or call GE Answer Center® service,
800.626.2000.
Cabinet
Width
(inches)
PSB1200/1 without
accessory drawer
PSB1200/1 with
accessory drawer
*For existing cutouts a maximum width of 28-1/2" is acceptable
30 29-25/32 19 -1 /8 21-3/4 25-1/8 17-1 /2 2 3-1 /2
30 29-25/32 2 2-1 /4 21-3/4
W
WidthH Height
D
Depth
(excluding
handle)
X
Cutout
Width
25-1/4 to
28 -1 /2 *
Specification Created 11/08
Y
Cutout
Height
Cutout
Depth
(minimum)
21 23 -1 /2
Listed by
Underwriters
Laboratories
240 446
Z
PSB1201NSS
Installation over a GE/Monogram
Warming Drawer:
30”
23-1/2”
25-1/4”
Min.
21”
2” Min.
(3” recom mended)
Per warming
drawe r
requi rement
Constru ct
Solid Bottom
Min. 3 /8”
Plywood
Support ed
by 2x4 or 2x2
Runners all
Four S ides
5” m in.
from floor
1” m in.
abov e
toek ick
Warming Drawer:
Construct Solid
Bottom Min.
3/8” Pl ywood
Supporte d by
2x4 or 2x2
Runners all
Four Si des
30”
23-1/2”
21”
2” Min.
Per Oven
Requirement
Per war ming drawer requirement
2” Min.
(3” recom mended)
25-1/4”
Min.
5” m in.
from floo r
1” m in.
abov e
toek ick
30”
23-1/2”
25-1/4”
Min.
21”
Construct
Base
Min. 3/8”
Plywood
Supported
by 2x4 or 2x2
Runners all
Four Sides
5” m in.
from floor
1” m in.
abov e
toek ick
GE Profile Advantium® 120 Volt - 30" Wall Oven
Preparation WITH an Accessory Drawer
Prepare the opening
The Advantium PSB1200/1 series can be installed in combination with
other GE/Monogram appliances. Always follow each product's Installation
Instructions to compete the installation.
Single Oven Installation:
Order a 30" wide single oven cabinet or cut the opening in a wall to the
dimensions shown.
* For existing cutouts, a maximum
width of 28-1/2" is acceptable. If
the opening is slightly wider, secure
a furring strip on each side of the
cutout for securing the oven.
• Allow 3/4" to 2-1/8" case trim overlap
on the sides and 7/8" overlap on the
bottom of the opening for all models.
The amount of overlap on the sides
depends on the actual cutout width.
Allow 1-1/4" case trim overlap on the
top for models PSB1200 and PSB1201
and for models ZSC1201 and ZSC1202.
• Oven overlaps will conceal cut edges on all sides of the opening.
Note: PSB1200/1 series Advantium can be installed below GE/GE Profile
non-downdraft gas and electric cooktops. It CANNOT be installed below
induction or Monogram (2GU3841385) gas cooktops.
Note: PSB1200/1 series Advantium oven comes with two lower trim
pieces. One is for use above 36-inch height installations and one is for
use below 36-inch installations. Use of the accessory drawer will replace
the bottom trim piece for applicable installations. Please see installation
instructions for full details.
For answers to your Monogram,® GE Profile™ or GE®
appliance questions, visit our website at ge.com or
call GE Answer Center® service, 800.626.2000.
Prepare the opening (cont.)
When installed over a single oven or a
warming drawer, allow at least 2" between
the two openings. This separation will
provide clearance for bottom overlap of the
Advantium and the other appliance overlaps.
Construct a solid oven floor of 3/8" min. thick
plywood supported by 2 x 4 or 2 x 2 runners
on all sides.
• the support must be level and rigidly
mounted, flush with the bottom edge of
the cutout.
Note: Additional clearances between the
cutouts may be required. Check to be sure the
oven supports above the Warming Drawer
location do not obstruct the required interior
depth and height. See Warming Drawer
installation instructions for details.
Installation over a GE/Monogram Oven
and Warming Drawer:
Note: Additional clearances between the
cutouts may be required. Check to be sure the
oven supports above the Warming Drawer
location do not obstruct the required interior
depth and height. See Warming Drawer
installation instructions for details.
CAUTION: For personal safety, the mounting
surface must be capable of supporting the
cabinet load, in addition to the added weight
of this approximate 80-pound oven and 30pound drawer, plus additional oven loads of up
to 50 pounds or a total weight of 160 pounds.
Listed by
Underwriters
Laboratories
Specification Created 11/08
240 446
Loading...