Page 1
Installation
Instructions
Advantium®120V
Built-In SpeedCook
Ovens
PSB1200
PSB1201
ZSC1201
ZSC1202
For a Spanish version of this manual, visit our Website at ge.com.
Para consultar una version en español de este manual de instrucciones,
visite nuestro sitiode internet ge.com.
49-40593-1
MFL59060901
12-08 JR
Page 2
Safety Information
2
CONTENTS
Design Information
Models Available......................................................................2
Product Dimensions and Clearances ............................3
Tools and Parts Required ....................................................3
Parts Supplied ..........................................................................3
Electrical Tools and Parts Required................................3
Advance Planning ..................................................................3
Installation Preparation
Electrical Requirements........................................................4
Install Junction Box ................................................................4
Preparing the Opening (Installation without
an accessory storage drawer)..................................5-8
Preparing the Opening (Installation with
an accessory storage drawer) ..............................9-12
Installation Under a 36″ Cooktop..................................12
Installation Instructions
Step 1, Remove Packaging and Parts ........................13
Step 2, Install Door Trim ....................................................14
Step 3, Route Conduit ........................................................14
Step 4, Install Bottom Trim ..............................................15
Step 5, Install Mounting Screws ....................................15
Step 6, Finalize Installation ..............................................15
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT — Save these instructions
for local inspector’s use.
IMPORTANT — Observe all governing codes
and ordinances.
• Note to Installer — Be sure to leave these
instructions with the Consumer.
• Note to Consumer — Keep these instructions
with your Owner’s Manual for future reference.
• Skill Level — Installation of this appliance
requires basic mechanical and electrical skills.
• Completion Time — 1 Hour.
• Proper installation is the responsibility
of the installer. Product failure due to improper
installation is not covered under the warranty.
See Owner’s Manual for warranty information.
NOTE: This oven is only approved to be installed
under the specific models as labeled on this unit.
IMPORTANT — Use this oven only
for its intended purpose. Never use the oven
for warming or heating a room. Prolonged use
of the oven without proper ventilation can
be hazardous.
CAUTION:
For personal safety, remove house fuse or oven
circuit breaker before beginning installation
to avoid severe or fatal shock injury.
CAUTION:
For personal safety, the mounting surface
must be capable of supporting the cabinet load,
in addition to the added weight of the 80-pound
oven and 30-pound drawer, plus additional oven
loads of up to 50 pounds or a total weight of up
to 160 pounds.
CAUTION:
If installing the Advantium 120V Oven below 36″,
you must use the plastic bottom trim due to burn
risk to children. The plastic trim acts as insulation
and will help prevent burns to children from hot
surfaces.
CAUTION:
If installing the Advantium 120V Oven below 36″,
do not remove the plastic door trim due to burn
risk to children. The plastic trim acts as insulation
and will help prevent burns to children from hot
surfaces.
MODELS AVAILABLE
Profile Models:
PSB1200WW–White*
PSB1200BB–Black
PSB1201SS–Stainless Steel
Monogram Models:
ZSC1201SS–Stainless Steel
ZSC1202SS–Stainless Steel**
*No color-matched drawer available for this model.
**This unit cannot be installed with an accessory
storage drawer.
Page 3
Design Information
3
PRODUCT DIMENSIONS AND CLEARANCES NOTE: Appearance will vary by model.
TOOLS AND PARTS REQUIRED
(NOT SUPPLIED)
• #2 Phillips screwdriver
• Hand-held drill
• High speed drill bit, 3/32″ diameter
• 3/8″ slot-head screwdriver
• Level
• Saw
• 2 x 4 or 2 x 2 lumber for installing runners
or 3/8″ plywood for floor (if required)
• Wood screws or other hardware for installing
runner or shelf to support oven (if required)
• Safety glasses or goggles
PARTS SUPPLIED
• 6 screws (3 required, 3 extra)
• 5 color-matched screws (4 required, 1 extra)
• Bottom trim (2)
ADVANCE PLANNING
• These ovens may be installed directly into a 30″ wide
oven cabinet.
• Cutout dimensions are NOT the same for installation
with or without an accessory storage drawer.
Make sure to use the correct cutout when preparing
the opening.
NOTE: ZSC1202 models CANNOT be installed
with an accessory storage drawer. See Installation
Preparation Without an Accessory Storage Drawer
for this model.
• Allow for clearance to adjacent corners, walls,
drawers, etc.
The oven must be securely installed in a cabinet
that is firmly attached to the house structure.
Weight on the oven door could cause the oven
to tip and result in injury. Never allow anyone
to climb, sit, stand or hang on the oven door.
If installing the drawer accessory, the drawer must
be assembled to the oven prior to installation into
the cabinet. See the Accessory Storage Drawer
Assembly Instructions.
21-1/2″
13/16″
13″
19″
29-3/4″
1-1/8″
5/8″
29 3/4”
19 1/32”
Page 4
Installation Preparation
4
ELECTRICAL REQUIREMENTS
Single Advantium 120 Installation:
This product requires a 120-volt, 60 Hz, 15-amp circuit
and draws 1.8 kilowatts. This product must be
connected to a supply circuit of the proper voltage
and frequency.
• Wire size must conform to the requirements of the
National Electrical Code or the prevailing local code
for this kilowatt rating.
• The power supply cord and plug should be brought
to a separate 15 or 20 ampere branch circuit single
grounded receptacle. The outlet box should be
located within reach of the 48" power cord.
ELECTRICAL LOCATION
IMPORTANT: (Please read carefully).
The power cord of this appliance is equipped with
a three-prong (grounding) plug that mates with
a standard three-prong grounding wall receptacle
to minimize the possibility of electric shock. The
customer should have the wall receptacle and
circuit checked by a qualified electrician to make
sure the receptacle is properly grounded and has
the correct polarity.
• Where a standard two-prong wall receptacle is
encountered, it is the personal responsibility and
obligation of the consumer to have it replaced with
a properly grounded three-prong wall receptacle.
Do not, under any circumstances, cut or remove
the third (ground) prong from the power cord.
DO NOT USE AN EXTENSION CORD.
Install a recessed electrical outlet in the back wall
of the opening within 6″ of either side and at least
9″ above the cutout floor.
Locate outlet box in the shaded area
6”
9”
Page 5
5
Installation Preparation
Preparation WITHOUT an Accessory Storage Drawer
PREPARE THE OPENING (cont.)
Installation over a GE/Monogram
Warming Drawer:
NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven supports
above the Warming Drawer location do not obstruct
the required interior depth and height. See Warming
Drawer installation instructions for details.
30″
23-1/2″
25-1/4″
17-1/2″
2″ Min.
(3
″ Recommended)
Per Warming
Drawer
Requirement
Construct
Solid Bottom
Min. 3/8″
Plywood
Supported
by 2 x 4 or 2 x 2
Runners all
Four Sides
PREPARE THE OPENING
The Advantium 120V can be installed in
combination with other GE/Monogram appliances.
Always follow each product’s Installation
Instructions to complete the installation.
Single Advantium 120V Installation:
Order a 30″ wide single oven cabinet or cut
the opening in a wall to the dimensions shown.
• Allow 2-1/8″ case trim overlap on the sides,
1-1/16″ overlap on the top and 7/8″ overlap
on the bottom of the opening for all models.
• Oven overlaps will conceal cut edges on all sides
of the opening.
When installed over a single oven or a warming
drawer, allow at least 2″ between the two openings.
This separation will provide clearance for bottom
overlap of the Advantium 120V and the other
appliance overlaps.
Construct a solid oven floor of 3/8″ min. thick plywood
supported by 2 x 4 or 2 x 2 runners on all sides.
• The support must be level and rigidly mounted,
flush with the bottom edge of the cutout.
30″
23-1/2″
25-1/4″
17-1/2″
Construct
Base
Min. 3/8″
Plywood
Supported
by 2 x 4 or
2 x 2 Runners
all Four Sides
Page 6
Installation Preparation
6
Preparation WITHOUT an Accessory Storage Drawer
PREPARE THE OPENING (cont.)
Installation over a GE/Monogram Oven and
Warming Drawer:
NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location
do not obstruct the required interior depth
and height. See Warming Drawer installation
instructions for details.
CAUTION: For personal safety, the
mounting surface must be capable of supporting
the cabinet load, in addition to the added weight
of this approximate 80-pound oven, plus
additional oven loads of up to 50 pounds
or a total weight of 130 pounds.
Construct Solid
Bottom Min.
3/8″ Plywood
Supported by
2 x 4 or 2 x 2
Runners all
Four Sides
30″
23-1/2″
25-1/4″
17-1/2″
2″ Min.
(3
″ Recommended)
Per Oven
Requirement
2″ Min.
(3
″ Recommended)
PREPARE THE OPENING (cont.)
Installation over a GE/Monogram oven:
• If you are replacing a GE/Monogram electric
double oven with the combined installation
of an Advantium 120V and a single oven, use
the dimensions shown. The middle rail separating
the two openings may need to be larger than
the 2″ minimum shown.
30″
23-1/2″
25-1/4″
17-1/2″
2″ Min.
(3
″ Recommended)
Construct Solid
Bottom Min.
3/8″ Plywood
Supported by
2 x 4 or 2 x 2
Runners all
Four Sides
Per Oven
Requirement
Per Warming
Drawer Requirement
Page 7
7
Installation Preparation
Preparation WITHOUT an Accessory Storage Drawer
PREPARE THE OPENING (cont.)
Installation under a GE/Monogram
Microwave Oven and over a Warming
Drawer:
NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location
do not obstruct the required interior depth
and height. See Warming Drawer installation
instructions for details.
CAUTION: For personal safety, the
mounting surface must be capable of supporting
the cabinet load, in addition to the added weight
of this approximate 80-pound oven, plus
additional oven loads of up to 50 pounds
or a total weight of 130 pounds.
Construct Solid
Bottom Min.
3/8″ Plywood
Supported by
2 x 4 or 2 x 2
Runners all
Four Sides
30″
23-1/2″
25-1/4″
17-1/2″
2″ Min.
(3″ Recommended)
Per Oven
Requirement
3.5″ Min.
(4.5
″ Recommended)
PREPARE THE OPENING (cont.)
Installation over another GE/Monogram
Under-the-Counter (UTC) oven:
• If you are mounting an Under-the-Counter
GE/Monogram oven over another, use the
dimensions shown. The middle rail separating
the two openings may need to be larger than
the 2″ minimum shown.
30″
23-1/2″
25-1/4″
17-1/2″
2″ Min.
(3
″ Recommended)
Construct Solid
Bottom Min.
3/8″ Plywood
Supported by
2 x 4 or 2 x 2
Runners all
Four Sides
17-1/2″
Per Warming
Drawer Requirement
Page 8
PREPARE THE OPENING (cont.)
Installation beside another GE/Monogram
Built-in Speedcook Oven:
• If you are mounting one Under-the-Counter
GE/Monogram oven beside the other, use the
dimensions shown. The middle rail separating
the two openings may need to be larger than
the 4-1/2″ minimum shown.
25-1/4″
17-1/2″
Installation Preparation
8
Preparation WITHOUT an Accessory Storage Drawer
Cooktop
Cooktop
25″
1-1/2″ Min.
4″ High
Toekick
23-1/2
″
25-1/4
″
17-1/2
″
36
″
Countertop
Height
NOTE: The oven is only approved to be installed
under the specific models as labeled on the unit.
23-1/2″
17-1/2″
4-1/2″ Min.
(5-1/2″ Recommended)
PREPARE THE OPENING (cont.)
Installation under a GE/Monogram 30″ or 36″ Cooktop or Countertop:
Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for the cutout
size. See the label on top of the oven for approved cooktop models. This oven requires a separate, properly
grounded 15-Amp, 120-Volt, 60Hz power supply. The cooktop requires a separate power supply. Use a 36″
or wider base cabinet.
Cooktop height including depth
of electrical box on some models.
Refer to cooktop installation
instructions.
No minimum clearance required
between cooktop and oven.
25-1/4″
Page 9
9
Installation Preparation
Preparation WITH an Accessory Storage Drawer
NOTE: MODEL ZSC1201 CAN ONLY BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER IF INSTALLED ABOVE 36-3/4″.
MODEL ZSC1202 CANNOT BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER. SEE INSTALLATION PREPARATION WITHOUT
AN ACCESSORY STORAGE DRAWER FOR THIS MODEL.
Installation over a GE/Monogram
Warming Drawer:
NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location
do not obstruct the required interior depth
and height. See Warming Drawer installation
instructions for details.
30″
23-1/2″
25-1/4″
Min.
21″
2″ Min.
(3
″ Recommended)
Per Warming
Drawer
Requirement
Construct Solid
Bottom Min. 3/8″
Plywood Supported
by 2 x 4 or 2 x 2
Runners all Four Sides
PREPARE THE OPENING (cont.)
The Advantium 120V can be installed in
combination with other GE/Monogram appliances.
Always follow each product’s Installation
Instructions to complete the installation.
Single Advantium 120V Installation:
Order a 30″ wide single oven cabinet or cut
the opening in a wall to the dimensions shown.
• Allow 2-1/8″ case trim overlap on the sides,
1-1/16″ overlap on the top and 7/8″ overlap
on the bottom of the opening for all models.
• Oven overlaps will conceal cut edges on all sides
of the opening.
When installed over a single oven or a warming
drawer, allow at least 2″ between the two openings.
This separation will provide clearance for bottom
overlap of the Advantium 120V and the other
appliance overlaps.
Construct a solid oven floor of 3/8″ min. thick plywood
supported by 2 x 4 or 2 x 2 runners on all sides.
• The support must be level and rigidly mounted,
flush with the bottom edge of the cutout.
30″
23-1/2″
25-1/4″
Min.
21″
Construct Base
Min. 3/8″ Plywood
Supported by 2 x 4
or 2 x 2 Runners
all Four Sides
PREPARE THE OPENING (cont.)
36-3/4″
Min.*
*Required for
Monogram models
*Required for
Monogram models
36-3/4″
Min.*
Page 10
10
Installation Preparation
Preparation WITH an Accessory Storage Drawer
NOTE: MODEL ZSC1201 CAN ONLY BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER IF INSTALLED ABOVE 36-3/4″.
MODEL ZSC1202 CANNOT BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER. SEE INSTALLATION PREPARATION WITHOUT
AN ACCESSORY STORAGE DRAWER FOR THIS MODEL.
PREPARE THE OPENING (cont.)
Installation over a GE/Monogram Oven and
Warming Drawer:
* For existing cutouts, a maximum width of 28-1/2″
is acceptable. If the opening is slightly wider,
secure a furring strip on each side of the cutout
for securing the oven.
NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location
do not obstruct the required interior depth
and height. See Warming Drawer installation
instructions for details.
CAUTION: For personal safety, the
mounting surface must be capable of supporting
the cabinet load, in addition to the added weight
of this approximate 80-pound oven and 30-pound
drawer, plus additional oven loads of up to
50 pounds or a total weight of 160 pounds.
Construct Solid
Bottom Min.
3/8″ Plywood
Supported by
2 x 4 or 2 x 2
Runners all
Four Sides
30″
23-1/2″
21″
2″ Min.
(3
″ Recommended)
Per Oven
Requirement
2″ Min.
(3
″ Recommended)
PREPARE THE OPENING (cont.)
Installation over a GE/Monogram Oven:
* For existing cutouts, a maximum width of 28-1/2″
is acceptable. If the opening is slightly wider,
secure a furring strip on each side of the cutout
for securing the oven.
• If you are replacing a GE/Monogram electric
double oven with the combined installation
of an Advantium 120V and a single oven, use
the dimensions shown. The middle rail separating
the two openings may need to be larger than
the 2″ minimum shown.
30″
23-1/2″
25-1/4″
Min.*
21″
2″ Min.
(3
″ Recommended)
Construct Solid
Bottom Min.
3/8″ Plywood
Supported by
2 x 4 or 2 x 2
Runners all
Four Sides
Per Oven
Requirement
25-1/4″
Min.*
*Required for
Monogram models
45-1/4″
36-3/4″
Min.
45-1/4″
Recommended*
Per Warming
Drawer Requirement
Page 11
11
Installation Preparation
Preparation WITH an Accessory Storage Drawer
NOTE: MODEL ZSC1201 CAN ONLY BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER IF INSTALLED ABOVE 36-3/4″.
MODEL ZSC1202 CANNOT BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER. SEE INSTALLATION PREPARATION WITHOUT
AN ACCESSORY STORAGE DRAWER FOR THIS MODEL.
PREPARE THE OPENING (cont.)
Installation under a GE/Monogram
Microwave Oven and over a Warming
Drawer:
NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location
do not obstruct the required interior depth
and height. See Warming Drawer installation
instructions for details.
CAUTION: For personal safety, the
mounting surface must be capable of supporting
the cabinet load, in addition to the added weight
of this approximate 80-pound oven, plus
additional oven loads of up to 50 pounds
or a total weight of 130 pounds.
Construct Solid
Bottom Min. 3/8″
Plywood Supported
by 2 x 4 or 2 x 2
Runners all Four
Sides
30″
23-1/2″
25-1/4″
3.5″ Min.
(4.5
″ Recommended)
PREPARE THE OPENING (cont.)
Installation over another GE/Monogram
Under-the-Counter (UTC) oven:
• If you are mounting an Under-the-Counter
GE/Monogram oven over another, use the
dimensions shown. The middle rail separating
the two openings may need to be larger than
the 2″ minimum shown.
30″
23-1/2″
25-1/4″
21″
2″ Min.
(3
″ Recommended)
Construct Solid
Bottom Min.
3/8″ Plywood
Supported by
2 x 4 or 2 x 2
Runners all
Four Sides
21″*
2″ Min.
(3
″ Recommended)
21″*
Per Oven
Requirement
Per Warming
Drawer Requirement
*Profile models only
*Profile models only
Page 12
12
Installation Preparation
Cooktop
Cooktop
25″
1-1/2″ Min.
4″ High
Toekick
23-1/2
″
25-1/4
″
21
″
36
″
Countertop
Height
PREPARE THE OPENING (cont.)
Installation beside another GE/Monogram
Built-in Speedcook Oven:
• If you are mounting one Under-the-Counter
GE/Monogram oven beside the other, use
the dimensions shown. The middle rail separating
the two openings may need to be larger than
the 4-1/2″ minimum shown.
25-1/4″
21″
Preparation WITH an Accessory Storage Drawer
NOTE: MODEL ZSC1201 CAN ONLY BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER IF INSTALLED ABOVE 36-3/4″.
MODEL ZSC1202 CANNOT BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER. SEE INSTALLATION PREPARATION WITHOUT
AN ACCESSORY STORAGE DRAWER FOR THIS MODEL.
NOTE: The oven is only approved to be installed
under the specific models as labeled on the unit.
23-1/2″
21″
4-1/2″ Min.
(5-1/2″ Recommended)
PREPARE THE OPENING (cont.)
Installation under a GE Profile 30″ or 36″ Cooktop or Countertop:
Gas or electric cooktops may be installed
over this oven. See cooktop installation
instructions for the cutout size. See the
label on top of the oven for approved
cooktop models. This oven requires
a separate, properly
grounded 15-Amp,
120-Volt, 60Hz power
supply. The cooktop
requires a separate power
supply. Use a 36″ or wider
base cabinet.
IMPORTANT:
For Profile models only.
The Monogram oven
and drawer combination
cannot be installed below
a countertop.
25-1/4″
Cooktop height including depth
of electrical box on some models.
Refer to cooktop installation
instructions.
No minimum clearance required
between cooktop and oven.
Page 13
REMOVE THE PACKAGING AND PARTS
1
13
Installation Instructions
• Remove all packing material and tape.
• Locate parts package containing mounting screws.
• Remove the oven from the carton. Do not lift unit
by handle or conduit. Two people are required to lift
this oven.
• Open the door and remove any packaging in oven.
Owner’s Manual
Installation
Instructions
Glass Tray
Metal Trays (2)
Turntable Ring
Bottom Trim – Plastic
6 Brass Screws
(3 required, 3 extra)
IMPORTANT: If installing the Advantium 120V Oven
with an accessory storage drawer, read the storage
drawer assembly instructions to assemble the
products together before proceeding to Step 2.
CAUTION:If installing the Advantium
120V Oven below 36″, you must use the plastic
bottom trim due to burn risk to children. The
plastic trim acts as insulation and will help
prevent burns to children from hot surfaces.
Cook Book
5 Color-Matched Screws
(4 required, 1 extra)
Cooking Guide
Bottom Trim – Metal
Rack
Owner’s
Manual
Cooking
Guide
Page 14
Installation Instructions
14
SLIDE THE OVEN INTO THE CUTOUT
CAUTION:Two people are required to
lift the oven into the opening. Grasp the bottom
at front and rear. DO NOT USE THE HANDLE TO LIFT
THE OVEN. DAMAGE WILL OCCUR.
• Lift and hold the oven at the front of the opening.
Hold the oven at an angle and plug in the power
cord.
• Carefully, slide the oven into the cabinet part
way. Leave the oven a few inches forward of
the cabinet frame.
• Check to be sure the power cord is not trapped
under the oven or along the sides of the oven.
3
DOOR TRIM REMOVAL FOR ABOVE
36″ INSTALLATION ONLY
If installing the Advantium 120V Oven above 36″
from the floor, you may remove the plastic trim
from the bottom of the door for esthetic purposes
if desired.
• If installing above 36″, remove the 3 screws that
secure the plastic trim to the bottom of the door.
• Discard plastic trim. Replace screws.
2
CAUTION:If installing the Advantium
120V Oven below 36″, do not remove the
plastic door trim due to burn risk to children.
The plastic trim acts as insulation and will help
prevent burns to children from hot surfaces.
Page 15
15
Installation Instructions
INSTALL MOUNTING SCREWS
• Slide the oven the remaining way into the opening
so that the side flanges and control panel are
against the cabinet frame. Make sure that the oven
is centered in the opening.
• Open the door, place a turntable tray in the oven
and make sure that the tray in the unit is level.
• Drill pilot holes through the side flanges.
• Drive the color-matched screws into the side
flanges. It is recommended that the screws
be hand tightened.
If installing oven with an accessory storage
drawer:
• Open the drawer.
• Drill pilot holes through the side flanges.
• Drive color-matched screws into the side flanges.
It is recommended that the screws be hand
tightened.
NOTE: If installing the Profile Advantium 120V Oven
with an accessory storage drawer, you must use
the Under-the-Counter (UTC) mounting bracket for
the drawer.
If installing the Monogram Advantium integrated
model ZSC1201 above 36″, the UTC mounting bracket
for the accessory storage drawer must be used.
6
FINALIZE INSTALLATION
• Turn power on at the source. The interior light
should come on when the door is opened.
• Refer to Owner’s Manual for operating instructions.
7
INSTALL BOTTOM TRIM
CAUTION:If installing the Advantium
120V Oven below 36″, you must use the plastic
bottom trim due to burn risk to children. The plastic
trim acts as insulation and will help prevent burns
to children from hot surfaces.
NOTE: If installing the Advantium 120V Oven
with an accessory storage drawer, the bottom trim
is not required. Proceed to Step 5.
• Installation Below 36″, align trim tabs on the plastic
trim to slots in the bottom of the oven.
• Installation Above 36″, align trim tabs on the plastic
or metal trim to slots in the bottom of the oven.
• Secure the bottom trim to the bottom of the oven
using 3 screws provided.
4
INSTALL BOTTOM TRIM WITH
ACCESSORY DRAWER
If installing with an accessory drawer, see
installation instructions on page 17 or instructions
that come with the accessory drawer.
5
Metal Trim
Plastic Trim
OR
Plastic Trim
Page 16
16
GE Consumer & Industrial Appliances
Assembly Instructions
Advantium®Built-In Accessory Storage Drawer
JX2200, JX2201, ZX2201
NOTE: Appearance will vary by model.
BEFORE YOU BEGIN
Read these instructions completely and carefully. Read
the Installation Instructions for the Advantium 120V or
240V oven completely and carefully for cutout
dimensions and step-by-step instructions.
IMPORTANT — Save these instructions for
local inspector’s use.
IMPORTANT — Observe all governing codes
and ordinances.
•
NOTE TO INSTALLER: Be sure to leave these
instructions with the Consumer.
•
NOTE TO CONSUMER: Keep these instructions with
your Advantium 120V or 240V Oven Owner’s Manual
for future reference.
•
SKILL LEVEL: Installation of this appliance requires
basic mechanical skills.
•
COMPLETION TIME: One hour with the installation
of an Advantium 120V or 240V oven.
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not
covered under the Warranty. See the Advantium
120V or 240V Oven Owner’s Manual for warranty
information.
TOOLS REQUIRED
• #2 Phillips screwdriver
PARTS SUPPLIED
• 2 Side Supports
• Screws (8)
• Screws (color-matched) (5)
• Under-the-Counter Mounting Bracket (1)
MODELS AVAILABLE
Profile Models:
JX2200BB–Black
JX2201SS–Stainless Steel
Monogram Models:
ZX2201SS–Stainless Steel (for installation above 36″ only)
NOTE: Advantium 240V model ZSC2202SS and
Advantium 120V model ZSC1202 CANNOT be
installed with an accessory storage drawer. See
Installation Preparation Without an Accessory Storage
Drawer in the Installation Instructions for these models.
PRODUCT DIMENSIONS AND CLEARANCES
Allow 15″ clearance
when fully open
5″
Page 17
UNDER-THE-COUNTER (UTC)
MOUNTING BRACKET INSTALLATION
NOTE: For UTC models PSB1200, PSB1201 and
ZSC1201 only.
Open the accessory drawer so you have
access to the top bracket.
Remove the three screws securing the top
bracket.
Install the new UTC mounting bracket using
the screws removed previously.
Close the drawer and proceed with the
installation.
2
D
C
B
A
REMOVE PACKAGING AND PARTS
• Remove the drawer from the carton.
• Remove all packing material and tape.
• Open the drawer and remove any parts inside.
• Locate parts.
1
ASSEMBLY TO ADVANTIUM BUILT-IN SPEEDCOOK OVEN
Assembly Instructions
Side Supports (2)
ASSEMBLING THE OVEN TO DRAWER
Place storage drawer on a surface with
the front of drawer hanging over the edge
of the surface. Not placing the front edge
of drawer over the edge of the surface may
result in damage to the drawer since the front
edge of drawer hangs below the bottom
of drawer.
Place the oven on top of the storage drawer.
Make sure that the back and sides of the oven
align with the back and sides of drawer.
NOTE: The bottom of the oven side flanges will
sit directly in front of the top of the storage
drawer side flanges.
B
A
3
17
Under-the-Counter (UTC)
Mounting Bracket
Color-Matched
Screws
(4 required,
1 extra)
Screws
(6 required,
2 extra)
Page 18
18
ASSEMBLING THE OVEN TO DRAWER
(cont.)
Remove the front two bottom screws on each
side of the oven and the top center screw on
each side of the storage drawer.
Place the side supports into the tabs on the
drawer and secure using the screws supplied
and the screws removed in Step C.
The oven and storage drawer assembly is now
ready to be installed. Return to the Advantium
120V or 240V Built-In SpeedCook Oven
Installation Instructions to complete
the installation.
C
E
D
Side
Support
120v only
ASSEMBLY TO ADVANTIUM BUILT-IN SPEEDCOOK OVEN
Page 19
19
Notes
Page 20
Printed in Korea
NOTE: While performing installations described in this book,
safety glasses or goggles should be worn.
NOTE: Product improvement is a continuing endeavor at
General Electric. Therefore, materials, appearance and
specifications are subject to change without notice.
GE Consumer & Industrial
Appliances
General Electric Company
Louisville, KY 40225
ge.com
Loading...