General Electric JP3030DJBV, CP9530SJSS, JP3030TJWW, JP5030SJSS Installation

Installation

30” Electric Cooktop - Radiant

Instructions

Excludes Down-Draft Models

If you have questions, call 800.GE.CARES or visit our website at: GEAppliances.com. In Canada, call 800.561.3344 or visit our website at: GEAppliances.ca.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT ³ Save these instructions

for local inspector’s use.

•

IMPORTANT ³Observe all governing

codes and ordinances.

•

Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions for future reference.

• Product failure due to improper installation is not covered under the Warranty.

MATERIALS YOU WILL NEED

Junction Box

Wire Nuts

TOOLS YOU WILL NEED

Pencil

WARNING ³ This appliance must be

properly grounded.

•

ATTENTION INSTALLER ³ALL

COOKTOPS MUST BE HARD WIRED (DIRECT WIRED) INTO AN APPROVED JUNCTION BOX. A “PLUG AND RECEPTACLE” IS NOT PERMITTED ON THESE PRODUCTS.

• Proper installation is the responsibility of the installer and product failure due to improper installation is NOT covered under warranty.

Phillips Head

Screwdriver

Ruler or Straightedge

Safety Glasses

90º or Straight

Squeeze Connector

for 1” Conduit

Saber Saw

1/8” Drill Bit & Electric or

Hand Drill

PARTS INCLUDED

4 Screws

(WB01X1137)

31-10985 (01-15 GE)

2 Hold Down

Brackets

Foam Tape

WB06K5042

Installation Instructions

IMPORTANT SAFETY INSTRUCTIONS

FOR YOUR SAFETY

• For Personal Safety, remove house fuse or open circuit breaker before beginning installation. Failure to do so could result in serious injury or death.

• Be sure your cooktop is installed properly by a qualified installer or service technician.

• To eliminate the risk of burns or fire due to reaching over heated surface elements, cabinet storage located above the surface units should be avoided. If cabinet storage space is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" beyond the bottom of the cabinets. Cabinet installation above the cooktop may be no deeper than 13".

• Make sure the cabinets and wall coverings around the cooktop can withstand the temperatures (up to 200°F) generated y the cooktop.

• The cooktop should be easy to reach and lighted with natural light during the day.

• Always disconnect the electrical service to the cooktop before repairing or servicing the cooktop. This can be done by disconnecting the fuse or circuit breaker. Failure to do this could result in a dangerous or fatal shock. Know where your main disconnect switch is located. If you do not know, have your electrician show you.

ELECTRICAL REQUIREMENTS

This appliance must be supplied with the proper voltage and frequency, and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or a time delay fuse as noted on name plate.

We recommend you have the electrical wiring and hookup of your cooktop connected by a qualified electrician. After installation, have the electrician show you where your main cooktop disconnect is located.

Wiring must conform to National Electrical Code. You can get a copy of the National Electrical Code, ANSI/NFPA No. 70-Latest Edition, by writing:

National Fire Protection Association

Batterymarch Park Quincy, MA 02269

The cooktop conduit wiring is approved for copper wire connection only, and if you have aluminum house wiring, you must use special UL approved connectors for joining copper to aluminum.

You must use a two-wire, three conductor 208/240 VAC, 60 Hertz electrical system. A white (neutral) wire is not needed for this unit. The cooktop must be installed in a circuit that does not exceed 125 VAC nominal to ground.

Refer to the name plate on your cooktop for the KW rating for your cooktop.

Name plate location

Installation Instructions

PRE-INSTALLATION CHECKLIST

WARNING – The electrical power to

the cooktop supply line must be shut off while connections are being made. Failure to do so could result in serious injury or death.

When preparing cooktop opening, make sure the

inside of the cabinet and the cooktop do not interfere with each other. (See section on preparing the opening.)

Remove packaging materials and literature

package from the cooktop before beginning installation.

Literature Package

Foam

Packaging

H OT

Cooktop

Be sure to place all literature, Owner’s Manual,

Installations, etc. in a safe place for future reference.

Make sure you have all the tools and materials

you need before starting the installation of the cooktop.

Your home must provide the adequate electrical

service needed to safely and properly use your cooktop. (Refer to section on electrical requirements.)

(Located under unit)

When installing your cooktop in your home,

make sure all local codes and ordinances are followed exactly as stated.

Make sure the wall coverings, countertop and

cabinets around the cooktop can withstand heat (up to 200°F) generated by the cooktop.

Installing cooktop in combination with other

products. Both products must be installed

according to their specific product installation instructions. Consideration must be given the separate electrical requirements and locations:

Over one or two wall ovens:

• Only certain models may be installed over wall ovens. The wall oven and cooktop will both have a label stating which models are approved in combination.

Over a Microwave:

• See microwave installation instructions for how to install a microwave under a cooktop. For vertical dimension of cooktop, see Approximate Cooktop Dimensions section.

In combination with telescopic downdraft vent:

• See telescopic downdraft vent instructions for how to install a vent behind a cooktop.

• The countertop must have a deep flat surface to accommodate the combined installation of the cooktop and vent.

Over a warming drawer:

• See warming drawer instructions for how to install a warming drawer under a cooktop. For vertical dimension of cooktop, see Approximate Cooktop Dimensions section.

PREPARING THE OPENING

The following MINIMUM clearance dimensions

must be maintained.

If a 30" clearance between the cooking surface and overhead combustible materials or metal cabinets cannot be maintained, a minimum clearance of 24" is required and the underside of the cabinets above the cooktop must be protected with not less than 1/4" insulating millboard covered with sheet metal not less than 0.0122" thick.

13" MAX. Depth of unprotected overhead cabinets

See label next to nameplate for minimum clearance to wall.

2" MIN. Clearance from cutout to side wall on the left of the unit

30" MIN. Clearance from countertop to unprotected overhead surface

1-1/2" MIN. Clearance from cutout to side wall on the right of the unit

15" MIN. Height from countertop to nearest cabinet on either side of unit

Installation Instructions

PREPARING THE OPENING (Cont)

APPROXIMATE COOKTOP

DIMENSIONS

29-3/4"

(29-7/8" SS)

Cooktop

19-1/4"

VERTICAL CLEARANCE

Allow 5” minimum vertical clearance from the cooktop bottom (or 8-1/4” minimum depth from the countertop) to any combustible surfaces, such as a cabinet drawer.

28"

21-7/8" (Monogram SS 21-1/2")

3-1/4" Front 4-3/16" Rear at the conduit location (JP3530, JP3030)

6" Rear on Electronic Touch and Backlit Knob Models

8-1/4"

DRAWER

Make sure the wall coverings, countertop and

cabinets around the cooktop can withstand heat (up to 200°F) generated by cooktop.

Wall covering, cabinets and countertop must withstand heat up to 200°F.

For Americans with Disabilities Act (ADA)

Forward Approach Installation Only:

5”

CUTOUT DIMENSIONS

OF THE COUNTERTOP

To insure accuracy, it is best to make a template when cutting the opening in the counter.

28-1/2" to

28-5/8”

length of

cut

1-3/4" Min. Between

cutout and the wall behind the cooktop

2-1/2" Min. from front edge of cutout and front edge of

countertop

JXTR32X CUTOUT FILLER TRIM KIT: A filler trim kit is available for use if your countertop cutout is larger than the dimensions shown, up to 29-13/16" x 20-7/16". Order JXTR32X to reduce the cutout opening for installation of this cooktop. This kit may be ordered from your GE Dealer.

19-5/8" to 19-3/4” width of cut

For models with no drop box, allow 5” minimum depth between the countertop and an enclosure. (JP3530 and JP3030)

For electronic touch and backlit knob models, allow 6-1/2” minimum depth between the countertop and an enclosure. (All other models)

6 1/2”

Drop box

NOTE: The enclosure must be made of wood material. Also, an access panel is required for the junction box, hold-down brackets, and service.

Installation Instructions

INSTALLING THE COOKTOP

INSTALLING THE JUNCTION BOX

Install an approved junction box where it will be easily reached through the front of the cabinet where the cooktop will be located. The cooktop conduit is 4 feet long.

16” Min.

Install junction box so that it can be reached through

the front of the cabinet.

IMPORTANT: The junction box must be

located where it will allow considerable slack in the conduit for serviceability.

ATTACH FOAM TAPE

Apply the foam tape around the outer edge of the glass. Do not overlap the foam tape.

Bottom of Cooktop

Foam Tape

Cooktop Glass

Note: On ZEU30 models, apply the foam tape around the outer edge of the glass on the sides and rear of the unit only.

LOCATE MOUNTING PARTS

Remove the hold down brackets and screws from the literature package.

Mounting Screw

PROTECT SURFACE OF COOKTOP

Place a towel or tablecloth onto the countertop. Lay the cooktop upside down onto the protected surface.

Bottom of Cooktop

Cloth under Cooktop

Screw the hold down bracket to the side of the cooktop unit. Repeat for opposite side of cooktop.

Bottom of Cooktop

Cooktop Glass

Pre-Drilled Hole

Foam Tape

Hold Down Bracket

+ 11 hidden pages