General Electric JGP985BEJBB User Manual

JGP985

www.GEAppliances.com

4226-0016-00 164D4290P414 49-80264 12-04 JR

Owner’s Manual

& Installation

Instructions

Cooktop

Safety Instructions . . . . .2–5

Operating Instructions

Accessories . . . . . . . . . . . . . .7

Controls . . . . . . . . . . . . . . 8, 9

Cookware . . . . . . . . . . . . . . 9

Electric Ignition . . . . . . . . . 8

Features . . . . . . . . . . . . . . . . 6

Griddle . . . . . . . . . . . . . . . .14

Grill Module . . . . . . . . .10–13

Surface Burner

Modules . . . . . . . . . . . 6, 8–10

Ventilation System . . . . . 6, 9

Care and Cleaning

Control Knobs and

Control Panel Seal . . . . . . 15

Grease Jar . . . . . . . . . . . . . 15

Griddle Accessory . . . . . . . 17

Grill Burner . . . . . . . . . . . . 16

Grill Grate . . . . . . . . . . . . . 16

Igniters . . . . . . . . . . . . . . . .17

Porcelain Burner Basin . . 17

Porcelain Cooktop . . . . . . 15

Sealed Burner Module . . . 17 Stainless Steel Surfaces . . .15

Vent Grille and Filter . . . . 16

Installation

Instructions . . . . . . . . .18–29

LP Conversion . . . . . .30–33

Troubleshooting

Tips . . . . . . . . . . . . . . .34, 35

Consumer Support

Consumer Support . . . . . .40

Product Registration . .37, 38

Warranty . . . . . . . . . . . . . . .39

Gas Downdraft

Write the model and serial numbers here:

Model # __________________

Serial #____________________

Find these numbers on a label under the cooktop.

IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING.

Safety Instructions

Operating Instructions

Care and CleaningTroubleshooting TipsConsumer Support

— Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other appliance.

—

WHAT TO DO IF YOU SMELL GAS

■ Do not try to light any appliance.

■ Do not touch any electrical switch; do not use

any phone in your building.

■ Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s instructions.

■ If you cannot reach your gas supplier, call the

fire department.

— Installation and service must be performed by

a qualified installer, service agency or the gas supplier.

WARNING: If the information in this manual

is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.

Safety Instructions

Operating Instructions Care and Cleaning

Troubleshooting Tips Consumer Support

www.GEAppliances.com

IMPORTANT SAFETY NOTICE

The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of substances known to the state to cause cancer, birth defects or other reproductive harm, and requires businesses to warn customers of potential exposure to such substances.

Gas appliances can cause minor exposure to four of these substances, namely benzene, carbon monoxide, formaldehyde and soot, caused primarily by the incomplete combustion of natural gas or LP fuels. Properly adjusted burners, indicated by a bluish rather than a yellow flame, will minimize incomplete combustion. Exposure to these substances can be minimized by venting with an open window or using a ventilation fan or hood.

Have the installer show you the location of the cooktop gas shutoff valve and how to shut it off if necessary.

■ Have your cooktop installed and properly

grounded by a qualified installer, in accordance with the Installation Instructions. Any adjustment and service should be performed only by qualified gas cooktop installers or service technicians.

■ Be sure your cooktop is correctly adjusted by a

qualified service technician or installer for the type of gas (natural or LP) which is to be used. Your cooktop can be converted for use with either type of gas. See the Installation Instructions. Your model is factory adjusted for use with natural gas.

■ Do not attempt to repair or replace any

part of your cooktop unless it is specifically recommended in this manual. All other service should be referred to a qualified technician.

■ Locate the cooktop out of kitchen traffic path

and out of drafty locations to prevent poor burner performance.

■ Plug your cooktop into a 120-volt grounded

outlet only. Do not remove the round grounding prong from the plug. If in doubt about the grounding of the home electrical system, it is your personal responsibility and obligation to have an ungrounded outlet replaced with a properly grounded, three-prong outlet in accordance with the National Electrical Code. Do not use an extension cord with this appliance.

■ Let the burner grate and other surfaces cool

before touching them or leaving them where children can reach them.

■ Be sure all packaging materials are removed

from the cooktop before operating it to prevent fire or smoke damage should the packaging material ignite.

■ Be sure your cooktop is correctly adjusted by a

qualified service technician or installer.

■ Do not leave children alone or unattended

where a cooktop is hot or in operation. They could be seriously burned.

■ Do not allow anyone to climb, stand or hang

on the cooktop.

■ CAUTION: Items of interest to children

should not be stored in cabinets above a cooktop—children climbing on the cooktop to reach items could be seriously injured.

■ Always keep wooden and plastic utensils

and canned food a safe distance away from your cooktop.

■ Always keep combustible wall coverings,

curtains or drapes a safe distance from your cooktop.

■ Never wear loose-fitting or hanging garments

while using the appliance. Be careful when reaching for items stored in cabinets over the cooktop. Flammable material could be ignited if brought in contact with flame or hot surfaces and may cause severe burns.

■ Teach children not to play with the controls

or any other part of the cooktop.

■ For your safety, never use your appliance

for warming or heating the room.

SAFETY PRECAUTIONS

Safety Instructions

Operating Instructions

Care and CleaningTroubleshooting TipsConsumer Support

IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING.

■ Always keep dish towels, dishcloths, pot

holders and other linens a safe distance from your cooktop.

■ Do not store flammable materials near

a cooktop.

■ Do not store or use combustible materials,

gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

■ Do not let cooking grease or other flammable

materials accumulate on or near the cooktop.

■ Do not operate the burner without all burner

parts in place.

■ Do not clean the cooktop with flammable or

volatile cleaning fluids.

■ Do not clean the cooktop when the appliance

is in use.

■ Avoid scratching the cooktop with sharp

instruments, or with rings and other jewelry.

■ Never use the cooktop as a cutting board.

■ Do not use water on grease fires. Never pick up

a flaming pan. Turn the controls off. Smother a flaming pan on a surface burner by covering the pan completely with a well-fitting lid, cookie sheet or flat tray. Use a multipurpose dry chemical or foam-type fire extinguisher.

■ Flaming grease outside a pan can be put out

by covering it with baking soda or, if available, by using a multipurpose dry chemical or foam-type fire extinguisher.

■ Do not obstruct the flow of combustion and

ventilation air.

■ Leak testing of appliance shall be conducted

according to the manufacturer’s instructions.

WARNING: To reduce the risk of fire,

electrical shock, or injury to persons, observe the following:

A. Use this unit only in the manner intended

by the manufacturer. If you have questions, contact the manufacturer.

B. Before servicing or cleaning the unit, switch

power off at service panel.

C. When cutting or drilling into wall or ceiling,

do not damage electrical wiring and other hidden utilities.

D. Ducted fans must always be vented to

the outdoors.

E. To reduce the risk of fire, use only metal

ductwork.

WARNING: To reduce the risk of a cooktop

grease fire:

A. Keep fan, filters and grease-laden surfaces

clean.

B. Always turn vent ON when cooking at

high heat.

C. Use high settings on cooktop only when

necessary. Heat oil slowly on low to medium setting.

D. Don’t leave the cooktop unattended when

cooking.

E. Always use cookware and utensils appropriate

for the type and amount of food being prepared.

CAUTION: For general ventilating use

only. Do not use to exhaust hazardous or explosive materials and vapors.

SAFETY PRECAUTIONS

Cook meat and poultry thoroughly—meat to at least an INTERNAL temperature of 160°F and poultry to at least an INTERNAL temperature of 180°F. Cooking to these temperatures usually protects against foodborne illness.

COOK MEAT AND POULTRY THOROUGHLY…

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

■ Always use the LITE position when igniting the

top burners and make sure the burners have ignited.

■ Never leave the surface burners unattended at

high flame settings. Boilovers cause smoking and greasy spillovers that may catch on fire.

■ Use only dry pot holders—moist or damp pot

holders on hot surfaces may result in burns from steam. Do not let pot holders come near open flames when lifting cookware. Do not use a towel or other bulky cloth in place of a pot holder. Such cloths can catch fire on a hot burner.

■ When using glass cookware, make sure it is

designed for cooktop cooking.

■ To minimize the possibility of burns, ignition

of flammable materials and spillage, turn cookware handles toward the side or center of the cooktop without extending over adjacent burners.

■ Always turn the surface burner controls off

before removing cookware.

■ Carefully watch foods being fried at a high

flame setting.

■ Always heat fat slowly and watch as it heats.

■ Do not leave any items on the cooktop. The hot

air from the vent may ignite flammable items and will increase pressure in closed containers, which may cause them to burst.

■ If a combination of oils or fats will be used in

frying, stir together before heating or as fats melt slowly.

■ Do not use a wok on the cooking surface

if the wok has a round metal ring that is placed over the burner grate to support the wok. This ring acts as a heat trap, which may damage the burner grate and burner head. Also, it may cause the burner to work improperly. This may cause a carbon monoxide level above that allowed by current standards, resulting in a health hazard.

■ Foods for frying should be as dry as possible.

Frost on frozen foods or moisture on fresh foods can cause hot fat to bubble up and over the sides of the pan.

■ Use the least possible amount of fat for effective

shallow or deep-fat frying. Filling the pan too full of fat can cause spillovers when food is added.

■ Use a deep fat thermometer whenever

possible to prevent overheating fat beyond the smoking point.

■ Never try to move a pan of hot fat, especially a

deep fat fryer. Wait until the fat is cool.

■ When flaming foods, turn the fan off. The fan,

if operating, may spread the flames.

■ Do not leave plastic items on the cooktop—

they may melt if left too close to the vent.

■ Keep all plastics away from the surface burners.

■ If you smell gas, turn off the gas to the cooktop

and call a qualified service technician. Never use an open flame to locate a leak.

■ To avoid the possibility of a burn, always be

certain that the controls for all burners are at the off position and all grates are cool before attempting to remove them.

■ Never clean the cooktop surface when it is hot.

Some cleaners produce noxious fumes and wet cloths could cause steam burns if used on a hot surface.

■ Never leave jars or cans of fat drippings on or

near your cooktop.

■ Do not use aluminum foil under burner grate.

Misuse could result in a fire hazard or damage to the cooktop.

■ Do not cover or block the area around the

cooktop knobs. This area must be kept clear for proper ventilation and burner performance.

■ Clean only parts listed in this Owner’s Manual.

Safety Instructions

Operating Instructions Care and Cleaning

Troubleshooting Tips Consumer Support

www.GEAppliances.com

Use proper pan size—avoid pans that are unstable or easily tipped. Select cookware having flat bottoms large enough to cover burner grate. To avoid spillovers, make sure cookware is large enough to contain the food properly. This will both save cleaning time and prevent hazardous accumulations of food, since heavy spattering or spillovers left on cooktop can ignite. Use pans with handles that can be easily grasped and remain cool.

WARNING!

SURFACE BURNERS

Safety Instructions

Operating Instructions

Care and CleaningTroubleshooting TipsConsumer Support

Features of your cooktop.

Throughout this manual, features and appearance may vary from your model.

Feature Index

Grill Module (optional)

Vent (fan operates automatically when grill is in use)

Vent Filter (located below the vent grille)

Cast-Iron Burner Grate

Surface Burners

Surface Burner Controls

Vent Control

1 2

Safety Instructions

Operating Instructions Care and Cleaning

Troubleshooting Tips Consumer Support

Cooktop accessories. www.GEAppliances.com

Throughout this manual, features and appearance may vary from your model.

Grill Model JXGG85

Consists of a black grill grate and a grill burner.

Sealed Burner Module Models JXGB85B (black), JXGB85S (stainless steel) and JXGB85W (white)

The grill assembly can be removed and a sealed burner module installed.

NOTE: Optional surface burner module (JXGB85) can replace the grill assembly. Burners supplied with cooktop and optional module air shutters have been adjusted for compatibility on both sides.

Griddle Model JXGL85

Can be used only with the grill burner. Self-draining griddle makes many favorite foods easier to fix. Family-sized surface lets you cook several pancakes, hamburgers or grilled sandwiches at the same time.

Safety Instructions

Operating Instructions

Care and CleaningTroubleshooting TipsConsumer Support

Using the gas surface burners.

Throughout this manual, features and appearance may vary from your model.

How to Light a Gas Surface Burner

Push the control knob down and turn it to the LITE position.

You will hear a little clicking noise—the sound of the electric spark igniting the burner.

After the burner ignites, turn the knob to adjust the flame size.

To turn a burner off, turn the knob clockwise, as far as it will go, to the OFF position.

If the flame is too low at the setting, the valve can be adjusted. Refer to Flames too

high or too low at the LOW setting in the Troubleshooting Tips section.

Push the control knob down and turn it to the LITE position.

How to Select Flame Size

For safe handling of cookware, never let the flames extend up the sides of the cookware.

Watch the flame, not the knob, as you reduce heat. The flame size on a gas burner should match the cookware you are using.

Any flame larger than the bottom of the cookware is wasted and only serves to heat the handle.

Electric Ignition

Your surface burners are lit by electric ignition, eliminating the need for standing pilots with constantly burning flames.

In case of a power outage, you can light the surface burners on your cooktop with a match. Hold a lit match to the burner, then turn the control knob to the high position. Use extreme caution

when lighting the burners this way.

Surface burners in use when an electrical power failure occurs will continue to operate normally.

IN CASE OF A POWER FAILURE, THE VENTILATION SYSTEM WILL NOT OPERATE. DO NOT USE THE GRILL MODULE OR GRIDDLE IF THE VENTILATION SYSTEM IS NOT OPERATIONAL.

Before Lighting a Gas Burner

■ Make sure all grates on the cooktop

are in place before using any burner.

■ Only surface burners may be used

on the right side.

After Lighting a Gas Burner

■ Do not operate the burner for an

extended period of time without cookware on the grate. The finish on the grate may chip without cookware to absorb the heat.

■ Check to be sure the burner you turn

on is the one you want to use.

■ Be sure the burners and grates are

cool before you place your hand, a pot holder, cleaning cloths or other materials on them.

■ When trying to simmer delicate

foods, use the right side of the unit for best results. The LO setting on the left side is hotter to accommodate the grill module. If you find that the LO setting is too hot, you can adjust the valve. See the Troubleshooting Tips section.

■ Do not allow large pans to extend

over the control knobs. Heat trapped between large pans and control knobs could cause possible damage to the control knobs.

The built-in vent system helps remove cooking vapors, odors and smoke from foods prepared on the cooktop.

To turn on the vent fan, use the vent control switch on the control panel.

• Turn the vent fan speed control

knob to HI, MED or LO as needed.

NOTE: Even if the switch is in the off position, the fan will operate automatically when the grill burner is in use.

Continuous use of the vent system while cooking helps keep the kitchen comfortable and less humid, reducing cooking odors and soiling moisture that normally creates a frequent need for cleaning.

The appearance of the burner flames may be affected when the vent fan is operating. At high fan speed setting, the flame may be drawn toward the vent opening, affecting cooking performance.

IN CASE OF A POWER FAILURE, THE VENTILATION SYSTEM WILL NOT OPERATE. DO NOT USE THE GRILL MODULE OR GRIDDLE IF THE VENTILATION SYSTEM IS NOT OPERATIONAL.

Safety Instructions

Operating Instructions Care and Cleaning

Troubleshooting Tips Consumer Support

Wok This Way

We recommend that you use a flat-bottomed wok, available at your local retail store.

Only a flat-bottomed wok should be used. Do not use a flat-bottomed wok with a wok holder.

Do not use a flat-bottomed wok on a support ring. Placing the ring over the burner or grate may cause the burner to work improperly, resulting in carbon monoxide levels above allowable current standards. This could be dangerous to your health.

Use a flat-bottomed wok.

Cookware

Use large diameter cookware on rear burners.

Aluminum: Medium-weight cookware is

recommended because it heats quickly and evenly. Most foods brown evenly in an aluminum skillet. Use saucepans with tight fitting lids when cooking with minimum amounts of water.

Enamelware: Under some conditions, the enamel of some cookware may melt. Follow cookware manufacturer’s recommendations for cooking methods.

Glass: There are two types of glass cookware: those for oven use only and those for cooktop cooking (saucepans, coffee and teapots). Glass conducts heat very slowly.

Cast Iron: If heated slowly, most skillets will give satisfactory results.

Heatproof Glass-Ceramic: Can be used for either surface or oven cooking. It conducts heat very slowly and cools very slowly. Check cookware manufacturer’s directions to be sure it can be used on a gas cooktop.

Stainless Steel: This metal alone has poor heating properties and is usually combined with copper, aluminum or other metals for improved heat distribution. Combination metal skillets usually work satisfactorily if they are used with medium heat as the manufacturer recommends.

Using your cooktop. www.GEAppliances.com

How to Operate the Downdraft Vent System

Using the downdraft vent system.

To Remove the Grill Module:

1. Make sure that all control knobs are

set to OFF and all grill components are cool.

2. Remove the grill grate.

3. Lift the grill burner up slightly and pull it away from the white slotted receptacle and brass orifices. Lift it out of the basin when it is completely unplugged.

4. Do not store or stack modules where they could fall or be damaged.

NOTE: The optional sealed burner module JXGB85 can replace the grill burner assembly.

Surface burner and grill modules.

Throughout this manual, features and appearance may vary from your model.

Safety Instructions

Operating Instructions

Care and CleaningTroubleshooting TipsConsumer Support

Sealed Burner Module

To Install the Sealed Burner Module:

1. Make sure that all control knobs are

set to OFF.

2. Clean the cooktop basin to remove

any grease accumulation. See the Care and Cleaning the Cooktop section.

3. With the back of the burner module tilted up and the two round openings and two pins facing toward the front, insert the module in the cooktop basin.

4. Slide the burner module forward until the pins start to engage the white slotted receptacle.

5. Lower the back of the module into place and carefully slide it forward until the pins are fully engaged.

6. Place the burner caps on the burners. Carefully place the grate onto the module with the two tabs on the underside toward the center of the cooktop.

To Remove the Sealed Burner Module:

1. Make sure that all control knobs are

set to OFF and that the cooktop is cool.

2. Lift up the edge of the burner module until the bottom of the module clears the edge of the basin.

IMPORTANT: Do not lift the module too high while it is still connected—you could damage the ignitor rods and mixer tubes.

3. Hold the module by the sides and pull it away from the slotted receptacle and brass orifices. Lift it out of the basin when it is completely unplugged.

4. Do not store or stack modules where they could fall or be damaged.

NOTE: The optional sealed burner module JXGB85 can replace the grill burner assembly.

Grill Module

To Install the Grill Module:

1. Make sure that all control knobs are

set to OFF.

2. Position the grill burner with the two round tubes and two pins facing the front.

3. Slide the grill burner forward until the pins and ignitors are engaged in the white slotted receptacle; then lower the burner until it rests on the mounting pins.

4. Carefully place the grill grate on the cooktop. The grate is designed to fit one way only. See the illustration.

NOTE: Before using the grill for the first time, heat the grill burner to remove the protective shipping coating. Heat the grill burner on HI for 10 minutes and use the vent system to remove any additional smoke during cooling.

The grill consists of a black grill grate and the grill burner. Only install the grill on the left side of your cooktop.

Safety Instructions

Operating Instructions Care and Cleaning

Troubleshooting Tips Consumer Support

Grilling. www.GEAppliances.com

Using the Grill

• The vent fan will operate

automatically when the grill burner is in use.

• Before using the grill for the first

time, wash grill grate in hot soapy water. Rinse and dry.

• Precondition grate by brushing with

vegetable oil or spraying with a nonstick coating such as Pam®. Do this every time before you grill.

• For easier clean-up, spray grate and

burner basin with a non-stick coating.

• Use nonmetallic spatulas or utensils

to prevent damaging the non-stick grill grate finish.

• Preheat the grill on high for 5 to 10

minutes. Preheating improves the flavor and appearance of meats and quickly sears the meat to help retain the juices.

• Excessive amounts of fat should be

trimmed from meats. Some fat is

necessary to produce the smoke needed for that smoked “outdoor” flavor. However, excessive fat can create cleaning and flare-up problems.

• Allowing excessive amounts of grease

or drippings to constantly flame voids the warranty on the grill grate. Excessive flare-ups indicate that either the grill interior needs to be cleaned, excessive amounts of fat are in the meat or that the meat was not properly trimmed.

• Grease drippings will occasionally

ignite to produce harmless puffs of flame for a second or two. This is a normal part of the cooking process.

• Never leave the grill unattended

during operation.

IMPORTANT:

IN CASE OF A POWER FAILURE, THE VENTILATION SYSTEM WILL NOT OPERATE. DO NOT USE THE GRILL MODULE OR GRIDDLE IF THE VENTILATION SYSTEM IS NOT OPERATIONAL.

• Do not use aluminum foil inside the grill area.

• Do not use charcoal or wood chips in the grill area.

• Do not allow burner basin to become overloaded with grease. Clean after each use.

• Do not cover grate completely with meat. Leave air space between each steak, etc., to allow proper ventilation as well as to prevent flare-ups.

• Do not use cooking pots, pans, skillets, etc., on the grill grate.

Should a Sustained Flare-Up Occur:

1. Use the vent control to turn the fan on.

2. Immediately turn the grill control knobs to the OFF position.

3. Remove the meat from the grill.

Grilling.

Safety Instructions

Operating Instructions

Care and CleaningTroubleshooting TipsConsumer Support

Grilling Tips

• With your grill, any food you’ve

considered “at its best” when prepared outdoors can now be prepared indoors with less fuss and great flavor.

• The following suggestions are good

rules to follow and will increase your enjoyment of the equipment. Be sure to follow directions in this guide for using the grill.

• Suggested cooking times and control

settings are approximate due to variations in meats. Experience will quickly indicate cooking times as well as which settings work best.

• For best results, buy top-grade meat.

Meat that is at least 3/4-inch thick will grill better than thinner cuts.

• For the attractive “branded” look on

steaks, be sure the grill is preheated. Allow one side of the meat to cook to the desired doneness, or until the juices appear on the top surface, before turning. Turn steaks and hamburgers just once. Moving the food around causes loss of juices.

• When basting meats or applying

sauces to foods, remember that excessive amounts wind up inside your grill and do not improve the food flavor. Apply sauces during the last 15 to 20 minutes of cooking time unless the recipe specifies otherwise. Sugar-based marinade (for example, barbecue sauce) will caramelize on grill grate and will create a cleaning chore.

• There are many meat marinades which

will help tenderize less expensive cuts of meat for cooking on the grill.

• Certain foods, such as poultry and

non-oily fish, may need some extra fat. Brush with oil or melted butter occasionally while grilling.

• Use tongs with long handles or

spatulas for turning meats. Do not use forks because these pierce the meat, allowing juices to be lost.

• To help retain meat juices, salt after

turning meat or after cooking is completed.

• Score the fat on the edges of steaks

but do not cut into the meat to prevent curling while cooking.

Safety Instructions

Operating Instructions Care and Cleaning

Troubleshooting Tips Consumer Support

Grilling guide. www.GEAppliances.com

Preheat the grill on high for 5 to 10 minutes for best flavor.

Type Control Setting Cooking Time Procedure

Meat

Steak (1/2″–3/4″)

Rare HI 6 to 10 minutes Turn after 3 to 5 minutes.† Medium HI 10 to 16 minutes Turn after 5 to 8 minutes. Well HI 21 to 24 minutes Turn after 6 to 12 minutes.

Steak (1″–11⁄4″)

Rare HI 14 to 24 minutes Turn after 7 to 12 minutes.† Medium HI 18 to 30 minutes Turn after 9 to 15 minutes.

Well HI 24 to 34 minutes Turn after 12 to 17 minutes. Hamburgers (3–4 oz.) Medium 20 to 25 minutes Turn after half the time. Pork chops Medium 20 to 30 minutes Turn occasionally. Fully cooked smoked pork chops Medium 10 to 15 minutes Turn after half the time. Ham slices Medium 15 to 20 minutes Turn after half the time. Pork ribs Medium 50 to 65 minutes Turn occasionally. Brush

with barbecue sauce during the last 15 minutes.

Fully cooked sausages

Hot dogs, brats HI 7 to 12 minutes Turn occasionally.

Polish HI 13 to 16 minutes Turn occasionally. Fresh sausages

Links Medium 15 to 25 minutes Turn occasionally.

Patties (3″ diameter) Medium 15 to 20 minutes Turn after half the time.

Italian sausage Medium 25 to 30 minutes Pierce casing with a fork.

Turn once.

Lamb chops Medium 20 to 30 minutes

Turn occasionally. Brush with glaze, if desired.

Poultry

Chicken

Pieces: bone-in Medium 35 to 50 minutes Turn occasionally.

Boneless breasts Medium 25 to 35 minutes Turn occasionally.

Wings Medium 25 to 35 minutes Turn occasionally. Cornish hen (halved) Medium 35 to 45 minutes Turn occasionally.

Fish

Small, whole (1″) Medium 15 to 20 minutes Brush with butter. Turn after

half the time.

Steaks (1″) Medium 20 to 25 minutes Brush with butter. Turn after

half the time.

Fillets—with skin on (1/2″) Medium 10 to 15 minutes Start skin side down. Brush

with butter. Turn after half the time.

Shrimp (skewered) Medium 10 to 20 minutes Turn and brush with butter

or marinade frequently.

Bread

Garlic bread Medium 4 to 6 minutes Turn after half the time.

Hot dog or hamburger buns Medium 1 to 2 minutes Turn after half the time.

† The U. S. Department of Agriculture says

“Rare beef is popular, but you should know that cooking it to only 140°F means some

food poisoning organisms may survive.” (Source: Safe Food Book. Your Kitchen Guide. USDA Rev. June 1985.)

Griddle.

Safety Instructions

Operating Instructions

Care and CleaningTroubleshooting TipsConsumer Support

Griddle Accessory

Using the griddle:

1. Before the first use, wash your new griddle in hot soapy water, rinse and dry. Then “condition” the surface by wiping on a thin coating of cooking oil or shortening. Remove excess oil or shortening by wiping again with another paper towel.

2. Insert grill burner. DO NOT use grill grate.

3. Place griddle over grill burner so that the drain holes are in front. This will permit excess grease to be collected in the grease container.

4. Preheat the griddle 5 to 10 minutes at the specified setting as noted in the Griddle Guide.

5. Use non-metallic spatulas or utensils while cooking to prevent damaging the finish.

IMPORTANT:

IN CASE OF A POWER FAILURE, THE VENTILATION SYSTEM WILL NOT OPERATE. DO NOT USE THE GRILL MODULE OR GRIDDLE IF THE VENTILATION SYSTEM IS NOT OPERATIONAL.

Griddle Guide

NOTE: These are suggested guides for control settings and times. Factors such as low gas pressure may affect the

times and control settings which provide the best results. Preheat 5 to 10 minutes at specified setting.

Control Approximate Cooking Approximate Cooking

Food Item Setting Time First Side Time Second Side

Bacon Medium 4–5 minutes 3–4 minutes Buns HI 2–3 minutes Eggs Medium 2–3 minutes 1 minute Fish sticks (frozen) Medium 7–8 minutes 5–7 minutes Ham slice Medium 6–7 minutes 5–6 minutes Hamburgers Medium 5–7 minutes 4–6 minutes Hot dogs HI 5 minutes 5 minutes French toast HI 2–4 minutes 2–3 minutes Grilled cheese sandwiches HI 2–3 minutes 2–3 minutes Pancakes HI 1–2 minutes 1–2 minutes Sausage patties Medium 6–8 minutes 4–5 minutes

Control Knobs and Control Panel Seal

After grilling there may be soot on the knobs and control panel seal. This soot can be removed by scrubbing with a plastic scrubber and mild dishwashing detergent. The control knobs may be removed for cleaning.

To remove a knob, pull it straight up.

Wash the knobs in soap and water but do not soak. Avoid getting water down into the knob stem holes.

Wipe with a sponge, damp cloth or paper towel. Do not scrub with steel wool pads or abrasive cleansers.

To replace a knob, match the flat part of the knob opening with the flat side of the shaft.

Care and cleaning of the cooktop. www.GEAppliances.com

Before Cleaning

Before cleaning any part of your cooktop, be sure all controls are off and DISCONNECT ELECTRICAL POWER TO THE COOKTOP at the fuse box or circuit breaker panel, or pull the

cooktop power plug, located beneath the cooktop and inside the cabinets.

Do not operate the cooktop without all parts in place.

Grease Jar

A grease jar is located below the grill basin pan under the countertop. Check periodically to prevent spillovers. Unscrew and remove.

If the jar is broken, replace with any heat tempered jar, such as a canning jar, that has a wide mouth screw neck.

Porcelain Cooktop

The porcelain enamel finish is sturdy but breakable if misused. This finish is acid-resistant. However, any acidic foods spilled (such as fruit juices, tomato or vinegar) should not be permitted to remain on the finish.

If acids spill on the cooktop while it is hot, use a dry paper towel to wipe it

up right away. When the surface has cooled, wash with soap and water or cleansing powders. Rinse well.

For other spills, such as fat spatterings,

wash with soap and water or cleansing powders after the surface has cooled. Rinse well. Polish with a dry cloth.

Stainless Steel Surfaces

Do not use a steel wool pad; it will scratch the surface.

1. Shake bottle well.

2. Place a small amount of CERAMA BRYTE®Stainless Steel Cleaner on a damp cloth or damp paper towel.

3. Clean a small area (approximately 8″ x 8″), rubbing with the grain of the stainless steel if applicable.

4. Dry and buff with a clean, dry paper towel or soft cloth.

5. Repeat as necessary.

NOTE: If a mineral oil-based stainless steel appliance cleaner has been used before to clean the appliance, wash the surface with dish soap and water prior to using the CERAMA BRYTE

Stainless Steel Appliance Cleaner. After washing the surface with dish soap and water, use a generous amount of CERAMA BRYTE®Stainless Steel Appliance Cleaner to clean the appliance.

To Order

To order CERAMA BRYTE®Stainless Steel Appliance Cleaner, please call our toll-free number:

National Parts Center 800.626.2002 www.GEAppliances.com CERAMA BRYTE

Stainless Steel Appliance

Cleaner . . . . . . . . . . . . . . . . . . . .# PM10X311

Safety Instructions

Operating Instructions Care and Cleaning

Troubleshooting Tips Consumer Support

The grill burner should be cleaned after each use. It can be cleaned with a non-

abrasive pad or in the dishwasher. Rinse and dry thoroughly before using again. For heavy soil, the burner should be cleaned first with a soapy steel wool pad, rinsed and dried. Then it can be cleaned in a self-cleaning oven for two hours.

NOTE: Check to be sure all burner ports are open. To open clogged ports, insert a twist tie directly into each port.

Grill Burner

Care and cleaning of the cooktop.

Safety Instructions

Operating Instructions

Care and CleaningTroubleshooting TipsConsumer Support

The grate should be cleaned after each use. It can be cleaned with

detergent and a plastic scrubber, such as Tuffy, or washed in the dishwasher if burned-on residue is first removed. For heavy soil, the grate can be soaked in hot, soapy water mixed with household ammonia.

Do not use metal brushes or abrasive scouring pads or other scrubbers intended to clean outdoor grills. These will remove the finish as well as scratch the grate. Do not clean in a self-cleaning oven or use oven cleaners on the grate.

Grill Grate

Vent Grille: The vent grille lifts off easily.

Wipe clean or wash in the sink with mild household detergents. NOTE: On models with a white vent grille, stubborn stains may be removed by soaking the grille in a 50/50 mix of bleach and water overnight. After cleaning, rinse the grille thoroughly and dry it before replacing.

Filter: Turn off the fan before removing. Turn the filter retainer clip to remove the filter. The filter is a permanent type and should be cleaned when soiled. Clean in the sink with warm water and liquid dishwashing detergent.

IMPORTANT: Do not operate the fan without the filter. The filter should always be placed at an angle. As you face the front of the cooktop, the top of the filter should rest against the left side of the vent opening and the bottom of the filter should rest against the right side of the ventilation chamber at the bottom. If the filter is flat against the fan wall, ventilation effectiveness is reduced.

Ventilation Chamber: This area, which houses the filter, should be cleaned in the event of spills or whenever it becomes coated with a film of grease. The ventilation chamber may be cleaned with a paper towel, damp cloth or sponge and a mild household detergent or cleanser.

Vent Grille and Filter

When replacing the filter, make sure it rests, at an angle, on the supports in the vent opening. Latch it in place.

Safety Instructions

Operating Instructions Care and Cleaning

Troubleshooting Tips Consumer Support

Griddle Accessory

DO NOT immerse a hot griddle in cold water.

Once the griddle has cooled, wash with soap or detergent in hot water in the sink. Be sure to remove all food residue before cooking on the griddle again.

Remove stubborn spots with a plastic scouring pad. For best results, use only those cleaning products which are recommended for use when cleaning non-stick surfaces. Do not use steel wool or coarse scouring pads.

DO NOT wash in a dishwasher.

www.GEAppliances.com

Igniters

It is important to keep igniter port openings on burners clear and free of obstructions to avoid ignition failure and possible gas buildup. If the port openings are blocked, use a twist tie to remove food particles.

Sealed Burner Module

Cooktop Surface:

To prevent the cooktop from discoloring or staining:

• Clean the cooktop after each use.

• Wipe up acidic or sugary spills

as soon as the cooktop has cooled, because these spills may discolor the porcelain.

Sealed Burners:

The sealed burners of your cooktop are secured to the cooktop module and are not designed to be removed. Since the burners are sealed into the module, boilovers or spills will not seep underneath the cooktop. However, the burner heads should be cleaned after each use.

Burner Grate:

The grate must be properly positioned before cooking. Improper installation of the grate may result in chipping of the cooktop.

Do not operate burners without a pan on the grate. The grate’s porcelain finish may chip without a pan to absorb the heat from the burner flame.

Although the burner grate is durable, it will gradually lose its shine and/or discolor, due to the high temperatures of the gas flame.

Burner Caps:

Lift off when cool. Wash burner caps in hot, soapy water and rinse with clean water. You may scour with a plastic scouring pad to remove burned-on food particles.

Porcelain Burner Basin

This area is located under the grill and surface burners and should be cleaned after each use of the grill.

To remove light soil, clean with soapy water or with a cleaner such as 409®. For easier cleanup, soak paper towels in a household cleanser, lay in the burner basin and soak for at least a half hour or longer.

To remove moderate soil, scrub with Comet®, Bon Ami®, a soft scrub cleanser or plastic scrubber.

To remove stubborn soil, spray with an oven cleaner. Let soak overnight. Wipe clean. Rinse and dry.

IMPORTANT SAFETY INSTRUCTIONS

The cooktop has been design-certified by CSA International. As with any appliance using gas and generating heat, there are certain safety precautions you should follow. You’ll find these precautions in the Important Safety Instuctions section in the front of this Owner’s Manual. Read them carefully.

• Be sure your cooktop is installed properly by a qualified installer or service technician.

• The cooktop must be electrically grounded in accordance with local codes, or in their absence, with the National Electrical Code ANSI/NFPA No. 70—Latest Edition.

• Installation of this cooktop must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code ANSI Z223.1/NFPA 54—Latest Edition.

• Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to this manual. For assistance or additional information, consult a qualified installer, service agency, manufacturer (dealer) or the gas supplier.

• Disconnect electrical supply before servicing.

• Never reuse old flexible connectors. The use of old

flexible connectors can cause gas leaks and personal injury. Always use NEW flexible connectors when installing a gas appliance.

• Make sure the wall coverings around the cooktop can withstand heat generated by the cooktop up to 200°F.

• Avoid placing cabinets above the cooktop.

• If cabinets are placed above the cooktop, allow a

minimum clearance of 30

″ between the cooking

surface and the bottom of protected cabinets.

• A non-combustible material must be installed on the under side of the cabinet. Use a flame retardant millboard at least 1/4″ (6.3 mm) thick, or gypsum board at least 3/16″ (4.7 mm) thick, covered with 28 gauge sheet steel or 0.020″ (.5 mm) thick copper. The maximum depth of cabinets above the cooktop is 13″ (33 cm).

FOR YOUR SAFETY

If You Smell Gas:

1. Open windows.

2. Don’t touch any electrical switches.

3. Extinguish any open flame.

4. Immediately call your gas supplier. Do not store or use gasoline or other flammable vapors

and liquids in the vicinity of this or any other appliance.

Installation Gas Downdraft Cooktop Instructions

If you have questions, call 800.GE.CARES (800.432.2737) or visit our Website at: www.GEAppliances.com

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT

–

Save these

instructions for local inspector’s use.

•

IMPORTANT

–

Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions

for future reference.

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not covered under the Warranty.

WARNING

–

Before beginning the installation, switch power off at the service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

In the Commonwealth of Massachusetts:

• This product must be installed by a licensed plumber or gas fitter.

• When using ball-type gas shut-off valves, they shall be the T-handle type.

• A flexible gas connector, when used, must not exceed 3 feet.

Sheet Metal

Screws (7)

Grease

Jar

Gas

Pressure

Regulator

Blower Assembly and

Mounting Nuts (4)

Blower

Plenum

Vent

Filter

Installation Instructions

UNPACK YOUR COOKTOP

• Cooktop with side holddown bolts (2)

• Blower assembly and nuts (4)

• Blower plenum

• Sheet metal screws (7)

• Vent grille

• Vent filter

• Sealed burner module

• Sealed burner grate

• Grease jar

• Sealed burner caps (2)

• Gas pressure regulator

• Attached 120-volt grounded

plug cord

• LP Conversion (attached to the electrical box)

PARTS INCLUDED

Cooktop with Side Hold-Down Bolts (2)

Sealed Burner

Module

Sealed Burner

Caps (2)

Burner Grate

Vent Grille

Shipping Tape

PREPARING FOR INSTALLATION

Installation Instructions

TOOLS AND PARTS NEEDED

• Large flat-blade screwdriver

• Phillips screwdriver

• 3/8″ socket and ratchet

• Saw

• Carpenter’s square

• Pipe wrench

• Gas line shut off valve

• Pipe joint sealant for use with gas connections that resists action of LP gas

For flexible connection where local codes permit:

• Flexible metal tubing (same 3/4″ or 1/2″ I.D. as gas supply line)

• Flare union adapter for connection to supply line (3/4″ NPT x 3/4″ I.D. or 1/2″ NPT x 1/2″ I.D.)

• Flare union adapter for connection to regulator (1/2″ NPT x 3/4″ I.D. or 1/2″ I.D.)

For rigid connection:

• Pipe fittings as required

Tie down bolt on each end

Grease Container

Pressure Regulator

Wiring Box Cover

29″ ±

⁄16″

*Blower can be swiveled 90°

9″

91⁄2″

17⁄8″ Min.

4.76 cm

⁄16″

21″ ±

⁄16″

Minimum Clearance

73.66 ± .16 cm

24.13 cm

2.38 cm

22.86 cm

53.5 ± .16 cm

143⁄16″

36.04 cm

IMPORTANT

Motor Clearance—Provide 2″ min. (5.1 cm) cabinet clearance to motor for cooling purpose.

NOTE: Where possible, 6″ (15.2 cm) is recommended for motor/blower service.

Side Clearance—Grills installed near a side wall should allow a minimum clearance of 8″ (20.3 cm).

You must allow room enough to remove and empty grease container(s).

CAUTION: Warranty is void on equipment installed other than as recommended by GE. Recommended wall caps and transitions must be used for proper operation and installation.

* Blower may be rotated for horizontal or vertical direction by loosening nuts around

blower inlet. Accessible inside ventilation chamber.

43⁄16″ 10.64 cm

⁄2″

47 cm

Minimum Clearance

2″

5.08 cm

Minimum

Clearance

141⁄2″

36.83 cm

⁄8″

32.7 cm

Grease Container

Appliance Pressure Regulator

Select appropriate duct

cutout. (See ducting

installation instructions.)

PREPARATION

INSTALLING CABINETS OVER YOUR COOKTOP

Avoid placing cabinets above the cooktop unit, if possible, in order to reduce the hazards caused by reaching over heated surface units.

If the cabinets are installed above the cooktop, allow a minimum 30″ (76.2 cm) clearance between the cooking surface and the bottom of the cabinet.

A non-combustible material must be installed on the under side of the cabinet. Use a flame retardant millboard at least 1/4″ (6.3 mm) thick, or gypsum board at least 3/16″ (4.7 mm) thick, covered with 28 gauge sheet steel or 0.020″ (.5 mm) thick copper. The maximum depth of cabinets above the cooktop is 13″ (33 cm).

EXCEPTION: Installation of a listed microwave oven or cooking appliance over the cooktop shall conform to the installation instructions packed with that appliance.

Working areas adjacent to the cooktop should have an 18″ (45.7 cm) minimum clearance between the countertop and the bottom of the cabinet. If the clearance is less than 18″ (45.7 cm), the adjacent cabinets should be at least 8″ (20.3 cm) from the side of the cooktop.

Installation Instructions

MINIMUM SPACING REQUIREMENT

When installing a double bay downdraft cooktop in combination with another downdraft cooktop, maintain the minimum spacing between units as shown below. Installing them too close will affect cooking performance.

25″

(63.5 cm)

30″ min

(76.2 cm)

30″ (76.2 cm)

13″

(33 cm)

18″ (45.7 cm)

8″ min to wall

(20.3 cm)

8″ min to wall

(20.3 cm)

36″

(91.4 cm)

18″

45.7 cm

43⁄8″

11.1 cm

PREPARATION

GAS AND ELECTRICAL LOCATION

The position of the electrical supply receptacle and the gas supply pipe entering the cabinet should be positioned as shown in the shaded areas marked below. The cooktop is equipped with a 4 ft (1.2 m) power cord, which should reach any desired location on the cabinet walls. The cooktop must be disconnected from the power supply before any servicing is carried out.

PREPARING THE COUNTERTOP

Cut out the opening as shown in the diagram. Measure carefully when cutting the countertop, making sure the sides of the opening are parallel and the front and rear cuts are exactly perpendicular to the sides.

The front of the opening must clear the front support rail on the cabinet, and the rear of the opening must clear the rear support of the cabinet.

Chamfer all exposed edges of decorative laminate to prevent damage from chipping.

Radius corners of cutout and file to ensure smooth edges and prevent corner cracking.

Rough edges inside corners which have not been rounded and forced fit can contribute to cracking of the countertop laminate.

Countertop must be supported within 3″ (7.6 cm) of cutout.

Installation Instructions

PROVIDE ADEQUATE GAS SUPPLY

This cooktop is designed to operate on natural gas only at 5″ (12.7 cm) of water column pressure or on LP gas at 10″ (25.4 cm) of water column pressure. It is shipped from the factory set for natural gas. If you decide to use this cooktop with LP gas, conversion adjustments must be made by a service technician or other qualified person.

A pressure regulator is to be connected in series with the manifold of the cooktop and must remain in series with the supply line, regardless of whether natural or LP gas is being used.

For proper operation, the maximum inlet pressure to the regulator must be no more than 10″ (25.4 cm) water column pressure for natural gas, or 14″ (35.5 cm) water column pressure for LP gas. For checking the regulator, the inlet pressure must be at least 1″ (2.5 cm) greater than the regulator output setting. If the regulator is set for 5″ (12.7 cm) of water column pressure, the inlet pressure must be at least 6″ (15.2 cm).

For ease of installation, and if local codes permit, the gas supply line into the cooktop should be 1/2″ (13 mm) or 3/4″ (19 mm) I.D. flexible metal appliance connector three (0.9 m) to five feet (1.5 m) in length.

Not less than 17⁄8″

(4.8 cm)

Not less than 15⁄16″ (2.4 cm)

813⁄16″ min. cut-out to wall (22.2 cm)

813⁄16″ min. cut-out

to wall (22.2 cm)

Countertop cut-out dimensions

Back of Counter

Front of Counter

PRESSURE TESTING

The maximum gas supply pressure for the regulator supplied on this appliance is 14″ (35.5 cm) W.C. The test pressure for checking this regulator must be at least 6″ (15.2 cm) W.C. for natural gas, and at least 11″ (27.9 cm) W.C. for LP. It is shipped from the factory set for natural gas at 5″ (12.7 cm) W.C.

This appliance and its individual shut-off valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1⁄2 PSIG.

This appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1⁄2 PSIG.

21″ ±1⁄16″

53.5 ± 0.16 cm

29″ ±1⁄16″

73.66 cm ± 0.16 cm

Gas pipe location

Electrical outlet 12″ (30.5 cm) above cabinet floor (mount on side or back cabinet wall 3″ [7.6 cm] min. from centerline)

3″ (7.6 cm) Min.

4″ (10.2 cm) (to clear toe kick area)

PREPARATION

PREPARE FOR DUCTWORK

NOTE: Ductwork MUST be vented outside. DO NOT vent into a wall, ceiling, crawlspace, attic or any concealed space.

Determine the best route for ductwork; it can be routed in a variety of ways depending on the kitchen layout.

IMPORTANT: The downdraft air discharge outlet for this unit is 3-1/4″ x 10″ rectangular. Plan ducting accordingly.

Typical duct arrangement countertop series.

Installation Instructions

BLOWER TO DUCTWORK ALIGNMENT

In general, the use of flexible ducting is discouraged because it can cause severely restricted airflow. However, if the blower outlet and the floor or wall duct location do NOT align well, then flexible METAL ducting can be used to adapt to an offset. Good alignment without use of flexible ducting is best.

NOTE:

Do not exceed the maximum recommended offset of 6″.

Do not allow the flexible ducting to kink or collapse.

Do stretch the flexible ducting as much as possible to eliminate as much of the corrugation as possible.

A 31⁄4″ x 10″ rectangle to 6″ round transition duct is available at your local building supply store.

NOTE: Illustrations are for planning purposes only.

Inside wall

cabinet

Up inside wall to roof

or overhang

Directly to outside

Between floor joists Through cabinet toe space

Peninsula or island

Peninsula

Outside wall

cabinet

NOTE: PVC sewer pipe type PSM 12454-B Schedule 40 ASTM D1785.

Wall Cap

Concrete Slab

6″ (15 cm)

Dia. PVC

Sewer Pipe

6″ (15 cm) Dia. Metal Duct

Pack tightly with gravel

or sand completely

around pipe

3-1/4″ x 10″ Rectangular to 6″ Round Transition

6″ (15 cm) Dia. 90° Metal Elbow

6″ (15 cm) Dia. Metal Duct

16″ (40.6 cm) Max.

12″

(30 cm)

Min.

6″ (15 cm) Dia. PVC Coupling

6″ (15 cm) Dia. PVC Sewer Pipe Elbow

6″ (15 cm)

Dia. PVC

Sewer

Pipe

6″

(15 cm)

Dia. PVC

Coupling

30′-0″ (9.14 m) Max.

Optional duct arrangement under concrete slab.

PVC duct should be used if installing under a poured concrete slab.

PREPARATION

Back Venting

(Requires 31⁄4″ x 10″)

Bottom Venting

6″ Max.

Centerline

to Centerline

Offset

Installation Instructions

INSTALL THE DUCTWORK

• Ducting must conform to local code materials.

• IMPORTANT: Save for local electrical inspector’s use.

• Use galvanized or aluminum duct in 6″ round or 31⁄4″ x 10″ size, or a combination of both.

• NOTE: Local building codes must be followed

in specifying approved type and schedule of ALL duct used.

• Always use an appropriate roof or wall cap with damper.

• Laundry type wall caps should NEVER be used.

• Install ductwork, making male-female connections in the direction of airflow as shown. Secure all joints with sheet metal screws and duct tape to assure an airtight seal.

• Use the shortest and straightest duct run possible.

For satisfactory performance, the duct run should not exceed 100 feet equivalent length.

• Use the Duct Length Chart on page 25 to find the

equivalent length of the run.

• Ducting a cooktop is easy but critical for proper performance.

• After reading these instructions, plan the duct run.

• Install the duct hardware.

GENERAL CONSIDERATIONS:

1. Use quality metal duct of at least 26-gauge

galvanized or 24-gauge aluminum. Inferior quality pipe and fittings can cause up to twice the restriction shown and is a poor value. See the Prepare for Duct Work section of this manual for optional under-slab ducting. Local codes may require a heavier gauge material or restrict PVC.

2. Distance between adjacent fittings (elbows,

transitions, etc.) should be at least 18″. The farther the better. Closer distance promotes turbulence which reduces airflow.

3. The number of downstream elbows or

transitions should be limited to three.

4. Handmade crimps are likely to cause restrictions.

5. If an alternate wall or roof cap is used, be

certain duct size is not reduced and that there is a backdraft damper. It is best to use listed caps to be certain of proper performance.

6. Thermal breaks: In areas of extreme cold weather,

it may be necessary to provide a short length of nonmetallic duct as close to the wall as possible to prevent conduction along the metal duct.

7. High altitude installations: It is advisable to

reduce allowable duct run by 20%.

8. Follow the duct calculation in this manual

carefully for best performance and satisfaction.

PLAN THE DUCT RUN

1. Make a sketch of the total system. Identify the type of each fitting and the length of straight pipe. Refer to the examples on page 25.

2. Enter your run into the Duct Length Chart on page 25. Elbows, wall caps and other fittings are shown in the chart with their equivalent straight duct length. Each fitting value must be added to the amount of straight duct length used to determine the overall straight duct equivalent length. Use the following examples as a guide.

3. Using good quality ducting material, install per these instructions. A few minutes and pennies spent now will pay long term dividends for the life of the cooktop.

Through cabinet toe space Between floor joist

Downward venting

Duct tape over seam and screw

Air flow

Screw

PREPARATION

+ 56 hidden pages