General Electric GTH18ISXSS Installation Manual
GEAppliances.com
Refrigerators
Top-Freezer
197D3354P013 49-60511-1 05-09 JR
Safety Instructions . . . . . . . . . . . .2–3
Operating Instructions
Additional Features . . . . . . . . . . . . . . . . .6
Automatic Icemaker . . . . . . . . . . . . . . . .7
Controls . . . . . . . . . . . . . . . . . . . . . . . . . .4
Crispers and Pans . . . . . . . . . . . . . . . . . .6
Dispenser . . . . . . . . . . . . . . . . . . . . . . . . .7
Shelves and Bins . . . . . . . . . . . . . . . . . . .5
Water Filter . . . . . . . . . . . . . . . . . . . . . . .4
Care and Cleaning
Care and Cleaning . . . . . . . . . . . . . . .8, 9
Replacing the Light Bulbs . . . . . . . . . . .9
Installation Instructions
Preparing to Install
the Refrigerator . . . . . . . . . . . . . . . . . . .10
Reversing the Door Swing . . . . . . .14–18
Water Line Installation . . . . . . . . . .11–14
Troubleshooting Tips . . . . . . .19–21
Normal Operating Sounds . . . . . . . . . .19
Consumer Support
Consumer Support . . . . . . . . .Back Cover
Performance Data Sheet . . . . . . . . . . .27
Product Registration
for Canadian Customers . . . . . . . . .23, 24
State of California Water
Treatment Device Certificate . . . . . . . .28
Warranty for
Canadian Customers . . . . . . . . . . . . . . .25
Warranty for U.S. Customers . . . . . . . .26
Réfrigérateurs
Congélateur supérieur
Refrigeradores
Congelador superior
Model 18
Manuel d’utilisation
et d’installation
Owner’s Manual and
Installation Instructions
Manual del propietario
e instalación
La section française commence à la page 29
La sección en español empieza en la página 53
Nota al instalador – Asegúrese de
dejar estas instrucciones con el consumidor.
Nota al consumidor – Conserve
estas instrucciones para referencia futura.
Write the model and serial numbers here:
Model # __________________________
Serial # __________________________
Find these numbers on the gray label
on the left side, near the top of the
refrigerator compartment.
Refrigerators
Top-Freezer
Note to Installer – Be sure to leave
these instructions with the Consumer.
Note to Consumer – Keep these
instructions for future reference.
Note à l’installateur – Assurez-vous de
laisser ces instructions au consommateur.
Note au consommateur – Conservez
ces instructions pour référence future.
Instructions de sécurité . . . .29–30
Instructions de fonctionnement
Bacs à légumes . . . . . . . . . . . . . . . . .33
Caractéristiques additionnelles . . . .33
Clayettes et bacs . . . . . . . . . . . . . . . .32
Distributeur . . . . . . . . . . . . . . . . . . . .34
Filtre à eau . . . . . . . . . . . . . . . . . . . .31
Machine à glaçons automatique . . .34
Réglages . . . . . . . . . . . . . . . . . . . . . .31
Soins et nettoyage
Remplacement des
ampoules électriques . . . . . . . . . . . .36
Soins et nettoyage . . . . . . . . . . . .35, 36
Instructions d’installation
Installation de la
conduite d’eau . . . . . . . . . . . . . .38–41
Inversion du sens
d’ouverture des portes . . . . . . . .41–45
Préparation à l’installation
du réfrigérateur . . . . . . . . . . . . . . . .37
En cas de panne . . . . . . . . .46–49
Bruits normaux
de fonctionnement . . . . . . . . . . . . . .46
Soutien au consommateur
Feuillet de données relatives à la
performance de la cartouche . . . . . . .51
Garantie . . . . . . . . . . . . . . . . . . . . . . .50
Soutien au consommateur . . . . . . . .52
Información de seguridad . . .53–54 Instrucciones de operación
Características adicionales . . . . . . . . . . .57
Controles . . . . . . . . . . . . . . . . . . . . . . . . .55
Dispensador . . . . . . . . . . . . . . . . . . . . . . .58
Estantes y compartimientos . . . . . . .56 –57
Filtro de agua . . . . . . . . . . . . . . . . . . . . . .55
Gavetas de almacenamiento . . . . . . . . .57
Máquina de hielos automática . . . . . . .58
Cuidado y limpieza
Cómo reemplazar las bombillas . . . . . .60
Cuidado y limpieza . . . . . . . . . . . . . .59–60
Instrucciones para la instalación
Cómo invertir el vaivén de
la puerta . . . . . . . . . . . . . . . . . . . . . . .65–69
Instalación de la tubería
del agua . . . . . . . . . . . . . . . . . . . . . . .62–65
Preparación para instalar
el refrigerador . . . . . . . . . . . . . . . . . . . . .61
Consejos para la solución
de problemas . . . . . . . . . . . . . . .70–74
Sonidos normales de operación . . . . . .70
Soporte al consumidor
Hoja de datos de funcionamiento . . . .78
Garantía . . . . . . . . . . . . . . . . . . . . . . . . . .77
Soporte al consumidor . . . . . . . . . . . . . .79
Escriba aquí el modelo y el número
de serie:
Modelo # ________________________________
Serie # __________________________________
Encuentre estos números en la etiqueta gris en
el lado izquierdo, cerca de la parte superior
del compartimiento del refrigerador.
Écrivez ici le numéro de modèle et le numéro de
série :
Modèle # ______________________________
Série # ________________________________
Vous trouverez ces numéros sur l’étiquette grise
située à gauche, près du haut du compartiment
réfrigérateur.
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
Use this appliance only for its intended purpose as described in this Owner’s Manual.
SAFETY PRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including the following:
■
■ This refrigerator must be properly installed
and located in accordance with the Installation
Instructions before it is used.
■
■ Do not allow children to climb, stand or hang
on the shelves in the refrigerator. They could
damage the refrigerator and seriously injure
themselves.
■
■ Do not touch the cold surfaces in the freezer
compartment when hands are damp or wet.
Skin may stick to these extremely cold surfaces.
■
■ Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
■
■ In refrigerators with automatic icemakers,
avoid contact with the moving parts of the
ejector mechanism, or with the heating element
located on the bottom of the icemaker. Do not
place fingers or hands on the automatic
icemaking mechanism while the refrigerator
is plugged in.
■
■ Keep fingers out of the “pinch point” areas;
clearances between the doors and between the
doors and cabinet are necessarily small. Be careful
closing doors when children are in the area.
■
■ Unplug the refrigerator before cleaning and
making repairs.
NOTE: We strongly recommend that any servicing be
performed by a qualified individual.
■
■ Setting either or both controls (some models only
have one control) to the
0 (off)
position does not
remove power to the light circuit.
■
■ Do not refreeze frozen foods which have
thawed completely.
Consumer Support
Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
2
USE OF EXTENSION CORDS
Because of potential safety hazards under certain conditions, we strongly recommend against the
use of an extension cord.
However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United
States) or a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding
type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.
DANGER! RISK OF CHILD ENTRAPMENT
PROPER DISPOSAL OF THE REFRIGERATOR
Child entrapment and suffocation are not
problems of the past. Junked or abandoned
refrigerators are still dangerous…even if they will
sit for “just a few days.” If you are getting rid of
your old refrigerator, please follow the instructions
below to help prevent accidents.
Before You Throw Away Your Old
Refrigerator or Freezer:
■ Take off the doors.
■ Leave the shelves in place so that children
may not easily climb inside.
Refrigerants
All refrigeration products contain refrigerants,
which under federal law must be removed prior
to product disposal. If you are getting rid of an
old refrigeration product, check with the company
handling the disposal about what to do.
3
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions
Installation Instructions
GEAppliances.com
WARNING!
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
For personal safety, this appliance must be properly grounded.
The power cord of this appliance is equipped with
a 3-prong (grounding) plug which mates with a
standard 3-prong (grounding) wall outlet to
minimize the possibility of electric shock hazard
from this appliance.
Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.
Where a standard 2-prong wall outlet is
encountered, it is your personal responsibility and
obligation to have it replaced with a properly
grounded 3-prong wall outlet.
The refrigerator should always be plugged into its
own individual electrical outlet which has a voltage
rating that matches the rating plate.
This provides the best performance and also
prevents overloading house wiring circuits which
could cause a fire hazard from overheated wires.
Never unplug your refrigerator by pulling on the
power cord. Always grip plug firmly and pull
straight out from the outlet.
Repair or replace immediately all power cords that
have become frayed or otherwise damaged. Do not
use a cord that shows cracks or abrasion damage
along its length or at either end.
When moving the refrigerator away from the
wall, be careful not to roll over or damage the
power cord.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
About the controls on the refrigerator.
Control Settings
Initially, set the control(s) at 5 (some models have
only one control). Allow 24 hours for the temperature
to stabilize.
Several adjustments may be required. Adjust the
control(s) one increment at a time and allow 12 hours
after each adjustment for the refrigerator to reach the
temperature you have set.
Setting the refrigerator control to 0 stops cooling in
both the freezer and refrigerator compartments but
does not shut off electrical power to the refrigerator.
The freezer control (on some models) has no effect on electrical power to the refrigerator.
Control settings will vary based on personal preferences, usage and operating conditions, and may require
more than one adjustment. Factors that affect temperature include the amount of food in the refrigerator or
freezer, the frequency of door opening and the temperature of food when it is placed in the refrigerator.
Installing the Filter
Cartridge
If you are replacing the
cartridge, first remove the
old one. To open the
cartridge cover, push in
where indicated and the
cover will drop down.
Remove the cartridge by
slowly rotating it to the left.
A small amount of water
may drip down.
CAUTION:
If air
has been trapped in the system,
the filter cartridge may be
ejected as it is removed. Use
caution when removing.
Apply a month and year
sticker to the new cartridge
to remind you to replace it
in
six months
.
Position the cartridge
inside the cartridge holder
and slowly rotate the
cartridge to the right until
it stops. When the
cartridge is properly
installed, you will feel it
“click” as it locks into
place. The blade on the
end of the cartridge
should be positioned
vertically.
Do not
overtighten
.
Close the cartridge cover.
Run water from the
dispenser for 3 minutes
(about 11⁄2 gallons) to clear
the system and prevent
sputtering. See
To Use the
Dispenser
section.
NOTE:
A newly-installed water
filter cartridge may
cause water
to spurt
from the dispenser.
About the water filter. (on some models)
Water Filter Cartridge
The water filter cartridge is
located inside the cartridge
holder in the back upper right
corner of the refrigerator
compartment.
NOTE:
Some models ship with the
filter bypass plug in place of the
filter cartridge. The filter bypass plug needs to be removed before
the filter cartridge is installed. Keep the filter bypass plug for
future use.
When to Replace the Filter
The filter cartridge should be replaced every
six months
or earlier
if the flow of water to the icemaker and dispenser decreases.
Filter Bypass Plug
You must use the filter bypass plug when
a replacement filter cartridge is not available. The dispenser and
the icemaker will not operate without the filter or filter bypass
plug.
Replacement Filters
To order additional filter cartridges in the United States, visit our
Website, GEAppliances.com, or call GE Parts and Accessories,
1.800.661.1616.
Filter Model GSWF
Customers in Canada should consult the yellow pages for
the nearest Mabe Service Center
.
4
Consumer Support
Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
(on some models)
Consumer Support
Troubleshooting TipsOperating Instructions
Safety Instructions Installation Instructions
About the shelves and bins.
GEAppliances.com
Not all features are on all models.
Rearranging the Shelves
Refrigerator Compartment
Freezer Compartment
To remove:
Lift and slide left.
Rotate up and out.
To replace:
Holding the shelf diagonally,
insert the left end of the shelf
into the center of the shelf
supports on the side wall.
Insert the right end of the
shelf into the shelf supports
on the side wall. Rest each
end of the shelf on the
bottom of the shelf supports.
To remove:
Tilt the shelf up at the front.
Lift the shelf up at the back
and bring the shelf out.
To replace:
While tilting the shelf up, insert
the top hook at the back of the
shelf in a slot on the track.
Lower the front of the shelf until
the bottom of the shelf locks into
place.
Some models have wire shelves that
can be adjusted in the same manner.
Non-Adjustable Shelves on the Door
Detachable shelves deepen and enclose fixed
door shelves, providing more storage room and
greater storage flexibility.
To remove:
Lift the shelf straight up; then pull out.
To replace:
Engage the shelf extender in the molded
supports on the door and push down.
It will lock in place.
Adjustable Bins on the Door
(on some models)
To remove:
Lift bin straight up; then pull out.
To replace or relocate:
Engage the bin in the molded supports
of the door and push down. Bin will lock
in place.
Tab
Opening
Front bar
Slide-Out Spillproof Shelf
(on some models)
The slide-out spillproof shelf allows you to reach
items stored behind others. The special edges
are designed to help prevent spills from dripping
to lower shelves.
NOTE: The shelves are shipped with tape on the
back. Remove this tape before attempting to remove
the shelf.
To remove:
Remove all items from shelf.
Slide the shelf out until it stops.
Lift the front edge of the shelf until the tabs
are above the shelf frame.
Continue pulling the shelf forward until it
can be lifted out and removed.
To replace:
Place the rear of the shelf on the shelf frame
just behind the front bar.
Slide the shelf back until the tabs are above
the openings.
Lower the shelf so that the tabs go into the
openings; then slide the shelf all the way in.
Make sure that the shelf sits flat after reinstallation and
doesn’t move freely from side to side.
Make sure you push the shelves all the way in before you
close the door.
Freezer Tilt-Out Bin
(on some models)
Push the button as you tilt out the bin.
To remove:
Hold the sides of the bin and
lift it straight up; then pull out.
To replace:
Engage the ends of the bin
in the molded supports on the door and
push down. It will lock in place.
NOTE: Do not overload the bin.
Adjustable bins can easily be carried from refrigerator to work area.
NOTE: Bins for the refrigerator and freezer doors are different sizes and are not interchangeable.
5
6
Consumer Support
Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
Adjustable Humidity Crisper
(on some models)
Slide the control all the way to the
HIGH
setting to provide high humidity
recommended for most vegetables.
Slide the control all the way to the
LOW
setting to
provide lower humidity levels recommended for
most fruits.
Snack Pan
(on some models)
This pan can be moved to
the most useful location for
your family’s needs.
Fruit and Vegetable Crispers
Excess water that may
accumulate in the bottom
of the drawers or under the
drawers should be wiped dry.
About the crispers and pans.
Not all features are on all models.
Removing the glass cover
About the additional features.
Not all features are on all models.
ShelfSaver™Rack
This slide-out rack holds twelve cans of soda
or two wine/water bottles (lengthwise).
Can be removed for cleaning.
To remove,
slide the rack out to the
stop
position, lift the rack up and past the
stop
,
and lift out.
Crisper Removal
Unload the bottom shelf before attempting to
remove the storage drawers.
To Remove:
Lift the drawers up slightly while pulling
them past the
stop
location.
If the door prevents you from taking out
the drawers, first try to remove the door
bins. If this does not offer enough
clearance, the refrigerator will need to
be rolled forward until the door opens
enough to slide the drawers out. In some
cases, when you roll the refrigerator out,
you will need to move the refrigerator
to the left or right as you roll it out.
To remove the glass cover:
Remove the glass, then the frame. When
replacing the glass, push the front edge
firmly into the frame.
Lift the back up off of its supports, slide it
backward, tilt it and take it out.
To remove the frame:
Lift the front of the frame, pull it forward,
tilt it and take it out.
Consumer Support
Troubleshooting TipsOperating Instructions
Safety Instructions Installation Instructions
7
About the automatic icemaker.
GEAppliances.com
A newly-installed refrigerator may take 12–24 hours to begin making ice.
Automatic Icemaker
(on some models)
The icemaker will produce approximately
3 to 31⁄2 lbs. of ice in a 24-hour period,
depending on the freezer compartment
temperature, room temperature, number
of door openings and other use conditions.
If the refrigerator is operated before the
water connection is made to the icemaker,
move the feeler arm to the
STOP
(up)
position.
When the refrigerator has been connected
to the water supply, move the feeler arm to
the
ON
(down) position.
The icemaker will fill with water when it
cools to 15°F. A newly-installed refrigerator
may take 12 to 24 hours to begin making
ice cubes.
Once the icemaker starts to make ice,
it may take up to 48 hours to fill the bin,
depending on the temperature settings
and number of door openings.
You will hear a buzzing sound each time
the icemaker fills with water.
Throw away the first few batches of ice
to allow the water line to clear.
Be sure nothing interferes with the sweep
of the feeler arm.
When the bin fills to the level of the feeler
arm, the icemaker will stop producing ice.
It is normal for several cubes to be joined
together.
If ice is not used frequently, old ice cubes
will become cloudy, taste stale, shrink or
fuse together.
On power switch models, the green power
light will blink if ice cubes get stuck in the
icemaker. To correct this, set the power
switch to
O (off)
and remove the cubes.
Set the power switch to
I (on)
to restart the
icemaker. After the icemaker has been
turned on again, there will be a delay of
about 45 minutes before the icemaker
resumes operation.
NOTE: In homes with lower-than-average water
pressure, you may hear the icemaker cycle multiple
times when making one batch of ice.
Icemaker accessory kit:
If your refrigerator did not already come
equipped with an automatic icemaker,
an icemaker accessory kit is available at
extra cost.
Check the back of the refrigerator for the
specific icemaker kit needed for your model.
To Use the Dispenser
(on some models)
The water dispenser is located on the left
wall inside the refrigerator compartment.
To dispense water:
Hold the glass against the recess.
Push the water dispenser button.
Hold the glass underneath the
dispenser for 2–3 seconds after
releasing the dispenser button.
Water may continue to dispense
after the button is released.
If no water is dispensed when the refrigerator is first
installed, there may be air in the water line system.
Press the dispenser button for at least 2 minutes to
remove trapped air from the water line and to fill the
water system. During this process, the dispenser
noise may be loud as the air is purged from the
water line system. To flush out impurities in the
water line, throw away the first 6 glassfuls of water.
NOTE: To avoid water deposits, the dispenser
should be cleaned periodically by wiping with a
clean cloth or sponge.
Water Filter Accessory
The water filter is an option at extra cost
and is available from your dealer. Specify
WR97X0214. It has complete installation
instructions and installs on 1/4″ O.D.
copper water line or plastic tubing that
is included in a GE SmartConnect
™
Refrigerator Tubing kit. When using the
plastic tubing, an additional piece of plastic
tubing (WX08X10002) must also be
ordered since the plastic tubing should
not be cut.
NOTE: The only GE approved plastic tubing is that
supplied in GE SmartConnect™Refrigerator Tubing
kits. Do not use any other plastic water supply line
because the line is under pressure at all times.
Certain types of plastic will crack or rupture with
age and cause water damage to your home.
Icemaker
Feeler Arm
Power
Switch
Green
Power Light
Feeler Arm in
the STOP
(up) position
Feeler Arm in
the ON (down)
position
Feeler arm model
Power switch model
There are 2 types of icemakers:
8
Consumer Support
Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
Care and cleaning of the refrigerator.
Cleaning the Outside
The door handles and trim.
Clean with
a cloth dampened with soapy water.
Dry with a soft cloth.
Keep the outside clean.
Wipe with a clean
cloth lightly dampened with kitchen
appliance wax or mild liquid dish
detergent. Dry and polish with a clean,
soft cloth.
The stainless steel door panels and handles.
The stainless steel panels can be cleaned
with a commercially available stainless steel
cleaner or a similar product using a clean,
soft cloth. Do not use appliance wax, polish,
bleach or products containing chlorine on
stainless steel doors and handles.
For best results, GE recommends using
stainless steel cleaner PM10X311 with
the WX10X307 polishing cloth, or for
convenience the SS cleaning wipes, part
number WX10X10001.
Do not wipe the refrigerator with a soiled dish cloth
or wet towel. These may leave a residue that
can erode the paint. Do not use scouring pads,
powdered cleaners, bleach or cleaners containing
bleach because these products can scratch and
weaken the paint finish.
Cleaning the Inside
To help prevent odors,
leave an open box of
baking soda in the fresh food and freezer
compartments.
Unplug the refrigerator before cleaning.
If this
is not practical, wring excess moisture out
of sponge or cloth when cleaning around
switches, lights or controls.
Use warm water and baking soda solution—
about a tablespoon (15 ml) of baking soda
to a quart (1 liter) of water. This both cleans
and neutralizes odors. Thoroughly rinse
and wipe dry.
Avoid cleaning cold glass shelves (on some models)
with hot water because the extreme temperature
difference may cause them to break. Handle glass
shelves carefully. Bumping tempered glass can cause
it to shatter.
Do not wash any plastic refrigerator parts in the
dishwasher.
Do not clean with any products containing detergent,
bleach or ammonia. They may damage the
refrigerator.
Condenser
There is no need for routine condenser
cleanings in normal home operating
environments. However, in environments
that may be particularly dusty or greasy, the
condenser should be cleaned periodically
for efficient refrigerator operation.
For models with a base grille,
the grille must
be removed in order to clean the condenser.
To remove the base grille:
Grasp it about 6″ from each end and pull
its bottom edge toward you.
To replace the base grille:
Insert the tops of the metal clips into the
oval vents, making sure one of the plastic
tabs on the back of the grille goes into each
of the oval vents. Then push the bottom of
the grille forward until it snaps into place.
Cleaning the condenser:
Sweep away or vacuum up dust.
For models with a base grille,
reach the
condenser by inserting a brush or vacuum
hose into the oval holes.
For models without a base grille,
reach the
condenser by inserting a brush or vacuum
hose under the bottom of the refrigerator.
For best results, use a brush specially
designed for this purpose. It is available
at most appliance parts stores.
Moving the Refrigerator
Be careful when moving the refrigerator
away from the wall. All types of floor
coverings can be damaged, particularly
cushioned coverings and those with
embossed surfaces.
BEFORE moving the refrigerator away from the wall,
be sure to adjust the leveling legs up. (See page 10
for details.)
Pull the refrigerator straight out and return
it to position by pushing it straight in.
Moving the refrigerator in a side direction
may result in damage to the floor covering
or refrigerator.
When pushing the refrigerator back, make sure you
don’t roll over the power cord or icemaker supply line
(on some models).
9
GEAppliances.com
Preparing for Vacation
For long vacations or absences, remove
food and unplug the refrigerator. Move
the refrigerator control to the
0 (off)
position
and clean the interior with a baking soda
solution of one tablespoon (15 ml) of
baking soda to one quart (1 liter) of water.
Leave the doors open.
Set the icemaker power switch to the
O (off)
position or move the feeler arm to the
STOP
(up) position (depending on model) and
shut off the water supply to the refrigerator.
If the temperature can drop below freezing,
have a qualified servicer drain the water
supply system (on some models) to prevent
serious property damage due to flooding.
Preparing to Move
Secure all loose items such as grille,
shelves and drawers by taping them
securely in place to prevent damage.
Be sure the refrigerator stays in an upright position
during moving.
Some models have only one light.
Freezer Compartment Dome Light
(on some models)
CAUTION:
Light bulbs may be hot.
Unplug the refrigerator.
The bulb is located behind a light
shield at the back of the freezer
compartment. To remove, squeeze
the top and bottom of the shield and
pull the shield off.
After replacing with an appliance bulb
of the same or lower wattage, replace
the shield.
Plug the refrigerator back in.
Replacing the light bulbs.
Setting either or both controls to 0 (off) does not remove power to the light circuit.
Refrigerator Compartment—Upper Light
CAUTION:
Light bulbs may be hot.
Unplug the refrigerator.
The bulbs are located at the top of the
compartment near the opening.
Replace with an appliance bulb of
the same or lower wattage.
Plug the refrigerator back in.
Light shield
Consumer Support
Troubleshooting TipsOperating Instructions
Safety Instructions Installation Instructions
10
Rollers allow you to move the refrigerator away from the
wall for cleaning.
Leveling Legs near each front corner of the refrigerator,
next to the rollers, should be adjusted if any of the
following occurs:
• Refrigerator wobbles due to front roller not being firmly
positioned on the floor.
• Door(s) do not close easily when opened to 45°.
NOTE:
• BEFORE moving the refrigerator away from the wall,
be sure to turn the leveling legs counterclockwise so that
the weight of the refrigerator is fully transferred to the
front rollers.
• The refrigerator will not be level from front to back. It
will have a slight backward tilt for proper door-closing.
To adjust the leveling legs,
turn the two front leveling
legs clockwise to raise the
front of the refrigerator and
counterclockwise to lower it.
ROLLERS AND LEVELING LEGS
Clockwise to raise
refrigerator
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•
IMPORTANT – Save these
instructions for local inspector’s use.
•
IMPORTANT – Observe all
governing codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these instructions
for future reference.
• Skill level – Installation of this appliance requires
basic mechanical skills.
• Completion time – Refrigerator Installation
15 minutes
Reversing the Door Swing
1 hour
• Proper installation is the responsibility of the
installer.
• Product failure due to improper installation is not
covered under the Warranty.
Allow the following clearances for ease of installation,
proper air circulation and plumbing and electrical
connections.
• Sides 1/8″ (3 mm)
• Top 1″ (25 mm)
• Back 1″ (25 mm)
If the refrigerator is to be installed next to a wall on the
hinge side, allow 5/16″ (8 mm) door clearance.
CLEARANCES
If the refrigerator has an icemaker, it will have to be
connected to a cold water line. A water supply kit
(containing copper tubing, shutoff valve, fittings and
instructions) is available at extra cost from your dealer,
by visiting our Website at GEAppliances.com (in
Canada at www.GEAppliances.ca) or from Parts and
Accessories, 1.800.661.1616.
WATER SUPPLY TO THE ICEMAKER
(on some models)
Installation Instructions
Model 18
If you have questions, call 1.800.GE.CARES
or visit our Website at:
GEAppliances.com
In Canada, call 1.800.561.3344
or Visit our Website at:
www.GEAppliances.ca
• Do not install the refrigerator where the temperature
will go below 60°F (16°C) because it will not run often
enough to maintain proper temperatures.
• Do not install the refrigerator where the temperature
will go above 100°F (37°C) because it will not perform
properly.
• Install it on a floor strong enough to support it fully
loaded.
REFRIGERATOR LOCATION
INSTALLING THE WATER LINE (ON SOME MODELS)
Recommended copper water supply kits are WX8X2, WX8X3
or WX8X4, depending on the amount of tubing you need.
Approved plastic water supply lines are GE SmartConnect
™
Refrigerator Tubing (WX08X10006, WX08X10015 and
WX08X10025).
When connecting your refrigerator to a GE Reverse Osmosis
Water System, the only approved installation is with a GE RVKit.
For other reverse osmosis water systems, follow the
manufacturer’s recommendations.
This water line installation is not warranted by the refrigerator
or icemaker manufacturer. Follow these instructions carefully
to minimize the risk of expensive water damage.
Water hammer (water banging in the pipes) in house plumbing
can cause damage to refrigerator parts and lead to water leakage
or flooding. Call a qualified plumber to correct water hammer
before installing the water supply line to the refrigerator.
To prevent burns and product damage, do not hook up the
water line to the hot water line.
If you use your refrigerator before connecting the water line,
make sure the feeler arm is in the
STOP
(up) position.
Do not install the icemaker tubing in areas where temperatures
fall below freezing.
When using any electrical device (such as a power drill) during
installation, be sure the device is double insulated or grounded
in a manner to prevent the hazard of electric shock, or is battery
powered.
All installations must be in accordance with local plumbing
code requirements.
BEFORE YOU BEGIN
Installation Instructions
WHAT YOU WILL NEED
• Copper or GE SmartConnect™Refrigerator Tubing kit,
1/4″ outer diameter to connect the refrigerator to the water
supply. If using copper, be sure both ends of the tubing are
cut square.
To determine how much tubing you need: Measure the distance
from the water valve on the back of the refrigerator to the water
supply pipe. Then add 8′ (2.4 m). Be sure there is sufficient extra
tubing (about 8′ [2.4 m] coiled into 3 turns of about 10″ [25 cm]
diameter) to allow the refrigerator to move out from the wall
after installation.
GE SmartConnect™Refrigerator Tubing Kits are available in the
following lengths:
6′ (1.8 m) – WX08X10006
15′ (4.6 m) – WX08X10015
25′ (7.6 m) – WX08X10025
Be sure that the kit you select allows at least 8′ (2.4 m) as
described above.
NOTE: The only GE approved plastic tubing is that supplied
in GE SmartConnect™Refrigerator Tubing kits. Do not use any
other plastic water supply line because the line is under pressure
at all times. Certain types of plastic will crack or rupture with age
and cause water damage to your home.
11
• A GE water supply kit (containing tubing, shutoff
valve and fittings listed below) is available at extra
cost from your dealer or from Parts and Accessories,
1.800.661.1616.
• A cold water supply. The water pressure must be
between 20 and 120 p.s.i. (1.4–8.1 bar).
• Power drill.
• 1/2″ or adjustable wrench.
• Straight and Phillips blade screwdriver.
• Two 1/4″ outer diameter compression nuts and
2 ferrules (sleeves)—to connect the copper tubing
to the shutoff valve and the refrigerator water valve.
OR
• If you are using a GE SmartConnect™Refrigerator
Tubing kit, the necessary fittings are preassembled
to the tubing.
• If your existing copper water line has a flared fitting
at the end, you will need an adapter (available at
plumbing supply stores) to connect the water line to
the refrigerator OR you can cut off the flared fitting
with a tube cutter and then use a compression fitting.
Do not cut formed end from GE SmartConnect
™
Refrigerator tubing.
• Shutoff valve to connect to the cold water line.
The shutoff valve should have a water inlet with a
minimum inside diameter of 5/32″ at the point of
connection to the COLD WATER LINE. Saddle-type
shutoff valves are included in many water supply kits.
Before purchasing, make sure a saddle-type valve
complies with your local plumbing codes.
WHAT YOU WILL NEED (CONT.)
Place the compression nut and ferrule (sleeve)
for copper tubing onto the end of the tubing and
connect it to the shutoff valve.
Make sure the tubing is fully inserted into the valve.
Tighten the compression nut securely.
For plastic tubing from a GE SmartConnect
™
Refrigerator Tubing kit, insert the molded end
of the tubing into the shutoff valve and tighten
compression nut until it is hand-tight; then tighten
one additional turn with a wrench. Overtightening
may cause leaks.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
CONNECT THE TUBING
TO THE VALVE
5
Turn the main water supply
on counterclockwise and flush
out the tubing until the water
is clear.
Shut the water off at the
water valve after about one
quart (1 liter) of water has
been flushed through the tubing.
FLUSH OUT THE TUBING
6
INSTALLING THE WATER LINE (CONT.)
Saddle-Type
Shutoff Valve
Compression
Nut
SmartConnect
™
Tubing
Packing Nut
Outlet Valve
Ferrule (sleeve)
Fasten the shutoff valve to the cold water pipe with
the pipe clamp.
Tighten the clamp screws until the sealing washer
begins to swell.
NOTE: Do not overtighten or you may crush the
tubing.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
FASTEN THE SHUTOFF VALVE
3
Route the tubing between the cold water line and
the refrigerator.
Route the tubing through a hole drilled in the wall
or floor (behind the refrigerator or adjacent base
cabinet) as close to the wall as possible.
NOTE: Be sure there is sufficient extra tubing to
allow the refrigerator to move out from the wall
after installation
.
ROUTE THE TUBING
4
Washer
Inlet End
Clamp Screw
Vertical Cold
Water Pipe
Saddle-Type
Shutoff Valve
Pipe Clamp
Installation Instructions
SHUT OFF THE MAIN WATER SUPPLY
AND UNPLUG REFRIGERATOR
Turn on the nearest faucet counterclockwise long
enough to clear the line of water.
Install the shutoff valve on the nearest frequently used
drinking water line.
1
Choose a location for the valve that is easily
accessible. It is best to connect into the side of a
vertical water pipe. When it is necessary to connect
into a horizontal water pipe, make the connection
to the top or side, rather than at the bottom, to
avoid drawing off any sediment from the water pipe.
Drill a 1/4″ hole in the water pipe (even if using a
self-piercing valve), using a sharp bit. Remove any
burrs resulting from drilling the hole in the pipe.
Take care not to allow water to drain into the drill.
Failure to drill a 1/4″ hole may result in reduced
ice production or smaller cubes.
DRILL THE HOLE FOR THE VALVE
2
12
13
Installation Instructions
NOTES:
• Before making the connection to the refrigerator,
be sure the refrigerator power cord is not
plugged into the wall outlet.
• We recommend installing a water filter if your
water supply has sand or particles that could clog
the screen of the refrigerator’s water valve. Install
it in the water line near the refrigerator. If using
GE SmartConnect™Refrigerator Tubing kit, you
will need an additional tube (WX08X10002) to
connect the filter. Do not cut plastic tube to
install filter.
Remove the screws holding the right side of the
access cover. Fold back the cover.
Remove the plastic flexible cap
from the water valve
(refrigerator connection).
Place the compression nut and
ferrule (sleeve) onto the end of
the tubing as shown. On GE
SmartConnect™Refrigerator
Tubing kit, the nuts are already
assembled to the tubing.
Insert the end of the tubing into the water valve
connection as far as possible. While holding the
tubing, tighten the fitting.
For plastic tubing from a GE SmartConnect
™
Refrigerator Tubing kit, insert the molded end
of the tubing into the water valve connection and
tighten compression nut until it is hand-tight;
then tighten one additional turn with a wrench.
Overtightening may cause leaks.
Fasten the tubing into the clamp provided to hold
it in a vertical position. You may need to pry open
the clamp.
CONNECT THE TUBING TO THE
REFRIGERATOR
Tighten any connections that leak.
TURN THE WATER ON AT THE
SHUTOFF VALVE
8
Reattach the access cover.
1/4″ Compression Nut
Tubing Clamp
1/4″ Tubing
Ferrule (sleeve)
Refrigerator
Connection
SmartConnect
™
Tubing
One of the illustrations below will look like the
connection on your refrigerator.
Icemaker Models without Water Dispenser
CONNECT THE TUBING TO THE
REFRIGERATOR (CONT.)
7
1/4″ Tubing
Tubing Clamp
1/4″ Compression Nut
Ferrule (sleeve)
SmartConnect™Tubing
Refrigerator Connection
Water Dispenser Models
7
When reversing the door swing:
• Read the instructions all the way through before
starting.
• Handle parts carefully to avoid scratching paint.
• Set screws down by their related parts to avoid using
them in the wrong places.
• Provide a non-scratching work surface for
the doors.
IMPORTANT: Once you begin, do not move the
cabinet until door-swing reversal is completed.
These instructions are for changing the hinges from
the right side to the left side—if you ever want to change
the hinges back to the right side, follow these same
instructions and reverse all references to left and right.
Unplug the refrigerator from its electrical outlet.
Empty all door shelves, including the dairy
compartment.
IMPORTANT NOTES
3/8″ Head socket driver
(a 6-point socket is
recommended)
TOOLS YOU WILL NEED
Phillips screwdriver
Putty knife or
thin-blade screwdriver
Masking tape
T20 or T25 Torx
®
driver, whichever your
model requires
14
On power switch models, set the icemaker power
switch to the
l (on)
position. On feeler arm models,
move the feeler arm to the
ON
(down) position.
The icemaker will not begin to operate until it
reaches its operating temperature of 15°F (–9°C) or
below. It will then begin operation automatically.
NOTE: In lower water pressure conditions, the
water valve may turn on up to 3 times to deliver
enough water to the icemaker.
Installation Instructions
Arrange the coil of tubing so that it does not vibrate
against the back of the refrigerator or against the
wall. Push the refrigerator back to the wall.
PLUG IN THE REFRIGERATOR
9
START THE ICEMAKER
Feeler Arm in the
STOP (up) position
Feeler Arm in
the ON (down) position
REVERSING THE DOOR SWING
INSTALLING THE WATER LINE (CONT.)
15
Installation Instructions
TRANSFER BOTTOM HINGE
BRACKET TO THE LEFT
For models with a base grille, remove it by grasping it
about 6″ from each end and pulling its bottom edge
toward you.
Using a Torx
®
driver, move the bottom hinge bracket
and plastic washer from the right side to the left side.
NOTE: If the washer is not on the hinge bracket,
check to see if it is stuck to the bottom of the door.
4
Plastic Washer
Hinge Bracket
For models with a base grille, before replacing the
base grille, remove the grille cap by removing the
screw. Screw the cap to the opposite side.
Replace the base grille by inserting the tops of the
metal clips into the oval vents, making sure one of the
plastic tabs on the back of the grille goes into each of
the oven vents. Then push the bottom of the grille
forward until it snaps into place.
REMOVE REFRIGERATOR DOOR
2
Tape the door shut with masking tape.
Remove the center hinge pin with a 3/8″ socket
and ratchet.
Remove the tape and tilt the door away from the
cabinet. Remove and save the washer on the hinge pin.
Lift the door straight up to free its bottom socket from
the pin in the bottom hinge bracket.
Set the door on a non-scratching surface with the
inside up.
CAUTION: Do not let door drop to the floor.
To do so could damage the door stop.
TRANSFER TOP HINGE TO
THE LEFT
Interchange hinge and screws at top right with screws
at the top left of cabinet.
Do not tighten screws on hinge side at this time.
3
Plastic Washer
Fresh Food Door
Hinge Pin
Center Hinge
Bracket
REMOVE FREEZER DOOR
1
Tape the door shut with masking tape.
Remove the hinge cover on top of the freezer door
(on some models).
Remove the two Torx
®
screws, then lift the hinge
straight up to free the hinge pin from the socket in
the top of the door.
Remove the tape and tilt the door away from the
cabinet. Lift it off the center hinge pin.
Set the door on a non-scratching surface with
the inside up.
Top Hinge
TRANSFER CENTER HINGE
BRACKET TO THE LEFT
Remove the center hinge bracket by removing the
three Torx®screws.
NOTE: Keep these screws with the hinge bracket.
They are long screws and will be used when installing
the hinge on the other side.
On some models, you will need to remove the colormatched caps from the screw heads before you can
remove the screws. Use the edge of a thin flat blade to
gently pry the caps off the screw heads. (A putty knife
works well for this.) Cover the blade with tape to
prevent scratching the paint.
Remove the three Torx®screws from the center left
side of the cabinet. Screw them into the holes on
the right side.
Place the center hinge bracket over the holes at
the center left side of the cabinet. Insert and
tighten the three long screws.
Replace the caps by snapping them over the screws
with your finger.
5
TRANSFER DOOR STOPS
On each door, move the metal door stop from the
right to the left.
Move any screws from the left to the right.
6
16
Door Stop
Door Stop
Left Side
Right Side
Screw Cap
Installation Instructions
REVERSING THE DOOR SWING (CONT.)
TRANSFER REFRIGERATOR
DOOR HANDLE TO THE RIGHT
Plastic handle:
Remove the plug
button by carefully
prying under the edge
with a putty knife.
Remove the
exposed screw holding
the handle. Remove
the two screws holding
the handle to the top
of the door.
Stainless steel handle (on some models):
Remove the two
screws holding the
handle to the top of
the door. Loosen the
set screw with the
3/32″ Allen wrench
(supplied) and remove
the handle. Remove
the handle fastener
with the 3/16″ Allen
wrench (supplied).
Transfer the fastener
to the right side and
move the plug button
to the left side of the
refrigerator door.
7
After removing the
handle: Move the small
plug buttons from the top
right side of the door top
and insert them into the
holes on the opposite side.
Small Plug
Buttons
Move the large plug
button from the left
edge of the door and
insert it into the hole
on the opposite side.
1
2
3
Handle
Plug
Handle
Plug
1
2
3
Fastener
Plug
Button
Plug Button
Installation Instructions
17
TRANSFER FREEZER DOOR
HANDLE TO THE RIGHT
Plastic handle:
Remove the screws
holding the handle to
the top and bottom of
the door. Remove
handle. Move the
plug button on the
right side of the door to
the handle screw hole
on the left side.
8
TRANSFER REFRIGERATOR DOOR
HANDLE TO THE RIGHT (CONT.)
Transfer the door plug
button to the opposite
side.
Reinstalling the handle:
Attach the handle to the
right side of the door.
7
Plastic handle:
Line up the handle with the
screw holes in the top of the door
and tighten the screws. Install the
screw into the bottom of the handle.
Reinstall the handle plug.
Handle
Plug
Button
Stainless steel handle
(on some models):
Attach the handle
to the fastener and
tighten with the 3/32″
Allen wrench
(supplied). Line
up the handle with the
screw holes in the top
of the door and
tighten the screws.
Stainless steel handle
(on some models):
Remove the two
screws holding the
handle to the bottom
of the door. Loosen the
set screw with the
3/32″ Allen wrench
(supplied) and remove
the handle.
Remove the handle
fastener with the 3/16″
Allen wrench
(supplied). Transfer
the fastener to the right side and move the GE badge
to the left side of the freezer door. Remove the paper
covering on the adhesive backing prior to attaching
the badge to the door.
Reattach the handle on the opposite side using the
holes closest to the edge of the door.
Plastic handle:
Line up the handle
with the screw hole in
the top of the door and
tighten screw. Install
the two screws into the
bottom of the handle.
Move the plug
button on the right
side of the door to the
handle screw hole on
the left side.
1
2
3
Fastener
1
2
3
4
1
3
2
Plug
Button
1
2
Plug
Button
2
1
3
RE-HANG THE REFRIGERATOR
DOOR
Lower the refrigerator door onto the bottom
hinge pin.
9
Straighten the door and line it up with the center
hinge bracket.
Reinstall the center hinge pin with a 3/8″ socket.
Turn it until it extends through the hinge bracket
and into the door.
Plastic
Washer
Plastic Washer
Refrigerator Door
Hinge Pin
Center Hinge
Bracket
18
RE-HANG THE FREEZER DOOR
Lower the freezer door onto the center hinge pin.
Be sure the washer is in place.
10
Lift the top hinge so the pin fits into the door socket.
Support the door on the handle side and make sure
the door is straight and the gap between the doors is
even across the front. While holding the door in
place, tighten the top hinge screws.
Center Hinge Pin
Plastic Washer
Installation Instructions
REVERSING THE DOOR SWING (CONT.)
TRANSFER FREEZER DOOR
HANDLE TO THE RIGHT (CONT.)
Stainless steel handle
(on some models):
Attach the handle to
the fastener and tighten
with the 3/32″ Allen
wrench (supplied).
Line up the handle
with the screw holes in
the bottom of the door
and tighten the screws.
8
1
2
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions
Installation Instructions
HUMMM...
WHOOSH...
■
The new high efficiency compressor may run faster and longer
than your old refrigerator and you may hear a high-pitched
hum or pulsating sound while it is operating.
■
You may hear a whooshing sound when the doors close.
This is due to pressure equalizing within the refrigerator.
Normal operating sounds.
GEAppliances.com
Newer refrigerators sound different from older refrigerators. Modern refrigerators
have more features and use newer technology.
■
You may hear the fans spinning at high speeds. This happens
when the refrigerator is first plugged in, when the doors are
opened frequently or when a large amount of food is added to
the refrigerator or freezer compartments. The fans are helping
to maintain the correct temperatures.
CLICKS, POPS,
CRACKS and CHIRPS
■
You may hear cracking or popping sounds when the
refrigerator is first plugged in. This happens as the refrigerator
cools to the correct temperature.
■
The compressor may cause a clicking or chirping sound when
attempting to restart (this could take up to 5 minutes).
■
Expansion and contraction of cooling coils during and after
defrost can cause a cracking or popping sound.
■
On models with an icemaker, after an icemaking cycle, you
may hear the ice cubes dropping into the ice bucket.
■
On models with a dispenser, during water dispense, you may
hear the water lines move at initial dispense and after
dispenser button is released.
WATER SOUN DS
■
The flow of refrigerant through the freezer cooling coils may
make a gurgling noise like boiling water.
■
Water dropping on the defrost heater can cause a sizzling,
popping or buzzing sound during the defrost cycle.
■
A water dripping noise may occur during the defrost cycle as
ice melts from the evaporator and flows into the drain pan.
■
Closing the door may cause a gurgling sound due to pressure
equalization.
Do you hear what I hear? These sounds are normal.
For additional information on normal
icemaker operating sounds, see the
About the automatic icemaker section.
Before you call for service…
Troubleshooting Tips
Save time and money! Review the charts on the following
pages first and you may not need to call for service.
Problem Possible Causes What To Do
Freezer door pops open
This is normal if, after • This indicates that there is a good seal on the freezer
when refrigerator door
popping open, the freezer door. If the freezer door does not automatically close after
is closed
door closed on its own. popping open, the rollers need adjusting. See
Rollers and
Leveling Legs.
Door does not close
Leveling legs need adjusting. • See
Rollers and Leveling Legs.
by itself
Refrigerator does
Refrigerator in defrost cycle. • Wait about 40 minutes for defrost cycle to end.
not operate
Refrigerator control in • Move the refrigerator and freezer control to a
0 (off)
position. temperature setting.
Refrigerator is unplugged. • Push the plug completely into the outlet.
The fuse is blown/circuit • Replace fuse or reset the breaker.
breaker is tripped.
Vibration or rattling
Refrigerator is not resting • Adjust leveling legs (See
Rollers and Leveling Legs).
(slight vibration
on all four rollers.
is normal)
19
Consumer Support
Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
Before you call for service…
Problem Possible Causes What To Do
Motor operates for
Normal when refrigerator • Wait 24 hours for the refrigerator to completely
long periods or cycles
is first plugged in. cool down.
on and off frequently
Often occurs when large • This is normal.
(Modern refrigerators
amounts of food are
with more storage
placed in refrigerator.
space and a larger
Door left open. • Check to see if package is holding door open.
freezer require more
Hot weather or frequent • This is normal.
operating time. They
door openings.
start and stop often
Temperature controls set • See
About the controls.
to maintain even
at the coldest setting.
temperatures.)
Refrigerator or freezer
Temperature control not set • See
About the controls.
compartment too warm
cold enough.
Warm weather or frequent • Set the temperature control one step colder.
door openings. See
About the controls.
Door left open. • Check to see if package is holding door open.
Freezer door popped open. • See the problem
Freezer door pops open when
refrigerator door is closed.
Frost or ice crystals
Door left open. • Check to see if package is holding door open.
on frozen food
Too frequent or too long
(frost within package
door openings.
is normal)
Food blocking freezer air vents. • Move items away from the back wall of the freezer.
Frequent “buzzing”
Icemaker power switch is in • On power switch models, set the power switch to the
O (off)
sound
the
I (on)
position, but the position. On feeler arm models, move the feeler arm to the
water supply to the refrigerator
STOP
(up) position. Keeping the power switch in the
I (on)
has not been connected. position or the feeler arm in the ON(down) position will
damage the water valve.
Small or hollow cubes
Water filter clogged. • Replace filter cartridge with new cartridge or with plug.
Automatic icemaker
Icemaker power switch is not on. • On power switch models, set the power switch to the
does not work I (on)
position. On feeler arm models, move the feeler
(on some models)
arm to the ON(down) position.
Water supply turned off or •See
Installing the water line.
not connected.
Freezer compartment too warm. • Wait 24 hours for the refrigerator to completely cool down.
Piled up cubes in the storage • Level cubes by hand.
bin cause the icemaker to shut off.
Ice cubes stuck in icemaker. • Turn off the icemaker, remove cubes and turn the
(Green power light on icemaker back on.
icemaker blinking.)
Ice cubes have
Ice storage bin needs cleaning. • Empty and wash bin. Discard old cubes.
odor/taste
Food transmitting odor/taste • Wrap foods well.
to ice cubes.
Interior of refrigerator • See
Care and cleaning.
needs cleaning.
Slow ice cube freezing
Door left open. • Check to see if package is holding door open.
Temperature control not set • See
About the controls.
cold enough.
• A newly installed refrigerator may take 12–24 hours
to begin making ice cubes.
Moisture forms on
Not unusual during • Wipe surface dry; then adjust the fresh food control
cabinet surface
periods of high humidity. setting one number higher and check again in 24 hours.
between the doors
Refrigerator has odor
Foods transmitting • Foods with strong odors should be tightly wrapped.
odor to refrigerator.
• Keep an open box of baking soda in the refrigerator;
replace every three months.
Interior needs cleaning. • See
Care and cleaning.
Refrigerator compartment
No power at outlet. • Replace fuse or reset the breaker.
light does not work
Light bulb burned out or loose. • See
Replacing the light bulbs.
20
GEAppliances.com
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions
Installation Instructions
Problem Possible Causes What To Do
Moisture collects inside
Too frequent or too
(in humid weather, air
long door openings.
carries moisture into
Open containers of water or • Cover or seal open containers. During a defrost cycle,
refrigerator when doors
warm food in the refrigerator. moisture will be removed from the refrigerator, but may
are opened)
return with long or frequent door openings.
Hot air from bottom
Normal air flow cooling motor. In the refrigeration process,
of refrigerator
it is normal that heat be expelled in the area under the refrigerator.
Some floor coverings will discolor at these normal and safe temperatures.
Food freezing in
Food too close to the air vent • Move the food away from the air vent (near the
the refrigerator
at the back of the refrigerator. controls).
Refrigerator control is set • Move the refrigerator control to a warmer
too cold. temperature setting one increment at a time.
Orange glow
Defrost heater is on. • This is normal.
in the freezer
Door bins do not fit
The freezer door bins are • Try to install the bins in both doors.
in the door
a different size than the
refrigerator door bins.
Freezer light does
Some models do not have a • Check for a semi-clear dome light shield in the freezer ceiling.
not work
freezer light. If the dome is opaque white, the model does not have a freezer
light. Check for a door activated light switch on the right side of
the freezer. If there is only a cap in place of a switch, the model
does not have a freezer light.
Light bulb burned out • See
Replacing the light bulbs.
or loose.
Controls do not light up
Some models do not have • If you can read white numbers on the control setting,
lighted controls. the model does not have lighted controls.
Refrigerator light bulb burned • See
Replacing the light bulbs.
out or loose.
Ice bucket does not fit
The freezer shelf is in the • Place the shelf in the lower position. See
Rearranging
under the icemaker
top position.
the shelves
.
Water has poor
Water dispenser has not been • Dispense water until all water in system is replenished.
taste/odor
used for a long time.
Water in first glass
Normal when refrigerator • Wait 24 hours for the refrigerator to completely cool down.
is warm
is first installed.
Water dispenser has not been • Dispense water until all water is system is replenished.
used for a long time.
Water system has been drained. • Allow several hours for replenished supply to chill.
Water dispenser
Water supply line turned off • See
Installing the water line
.
does not work
or not connected.
Water filter clogged. •Replace filter cartridge or remove filter and install plug.
Air may be trapped in • Press the dispenser arm for at least 2 minutes.
the water system.
Water spurting from
Newly-installed filter cartridge. • Run water from the dispenser for 3 minutes
dispenser
(about 11⁄2 gallons).
Water is not dispensed
Water in reservoir is frozen • Set the refrigerator control to a warmer setting and
but icemaker is working
because the controls are wait 24 hours. If water does not dispense after 24 hours,
set too cold. call for service.
No water or ice cube
Supply line or shutoff valve • Call a plumber.
production
is clogged.
Water filter clogged. •Replace filter cartridge or remove filter and install plug.
Filter cartridge not • Remove and reinstall filter cartridge, being certain that
properly installed. it locks into place. The blade on the end of the cartridge
should be positioned vertically.
Water is leaking from
Glass not being held under • Hold the glass underneath the dispenser for 2–3 seconds
dispenser
the dispenser long enough after releasing the dispenser button. Water may continue
after button is released. to dispense after the button is released.
Air may be present in the • Dispense water for at least 2 minutes to remove air
water line system, causing from system.
water to drip after being
dispensed.
21
22
Consumer Support
Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
Notes.
23
OWNERSHIP REGISTRATION
P.O. BOX 1780
MISSISSAUGA, ONTARIO
L4Y 4G1
(FOR CANADIAN CONSUMERS ONLY)
Please place in envelope and mail to:
Veuillez mettre dans une enveloppe et envoyez à :
✁
Cut here
24
✁
Cut here
Loading...