Page 1
GTD65GBSJ
GE® Series 7.4 Cu. Ft. Capacity Aluminized Alloy Drum Gas Dryer with HE Sensor Dry
DimEnsiOns anD installatiOn infOrmatiOn (in inchEs)
Exhaust OptiOn: When viewed from the front
of the unit, exhaust 3-way via rear, left and bottom.
Dryer is shipped exhausted to the rear. Alternate
exhausting knockouts are supplied.
Gas: An individual, properly-grounded branch circuit,
with a three-prong grounding-type receptacle, protected
by a 15 or 20 amp circuit breaker or a time-delay fuse is
required.
Gas DryEr ElEctric ratinG: 120V, 60Hz, 6A
Gas (Btu/hr): 22,000. Factory-equipped for
natural gas. Tested for LP gas. LP gas supply requires
a conversion kit. Check installation instructions for
correct kit and have a qualified gas technician install a
conversion kit. See dryer ducting information for proper
installation.
nOtE: Dryer wall outlet must be located within 36" of
service cord entry and accessible when dryer is mounted
in position.
installat iOn infO rmati On: For complete
information, see installation instructions packed with
your dryer.
spEcial installatiOn rEquirEmEnts
alcOvE Or clOsEt installatiOn:
- If your dryer is approved for installation in an alcove or closet, it will be stated on a
label on the dryer back.
- The dryer MUST be exhausted to the outside.
- Minimum clearances between dryer cabinet and adjacent walls or other surfaces
are: 0" either side; 3" front and rear
- Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52”.
- Closet doors must be louvered or otherwise ventilated and must contain a
minimum of 60 sq. in. of open area equally distributed. If this closet contains
both a washer and a dryer, doors must contain a minimum of 120 sq. in. of
open area equally distributed.
- No other fuel-burning appliance shall be installed in the same closet with a
ga s d ryer.
BathrOOm Or BEDrOOm installatiOn:
- The dryer MUST be exhausted to the outdoors.
- The installation must conform with the local codes, or in the absence of local
codes, with the National Electric Code and National Fuel Gas Code, ANSI
Z223 for gas dryers.
minimum clEarancEs OthEr than alcOvE Or clOsEt
installat iOn:
- Minimum clearances to combustible surfaces are: 0" both sides; 3" rear
DryEr ExhaustinG infOrmatiOn :
- Use metal duct only, vertical and horizontal ducting.
For answers to your Monogram®, GE Profile™ Series
or GE® Series appliance questions, visit our website
at geappliances.com or call GE Answer Center®
service, 800.626.2000.
Specification Created 7/15
Page 2
GTD65GBSJ
22 1/2"
30 1/2"
27"
3 1/2"
1 3/4"
3 1/4"
8"
38 1/2"
46"
27"
5"
Power Cord 4 1/2"
11 3/4"
Side View Rear View
5
Back View
Power
Cord Hole
4-1/2
GE® Series 7.4 Cu. Ft. Capacity Aluminized Alloy Drum Gas Dryer with HE Sensor Dry
DimEnsiOns anD installatiOn infOrmatiOn (in inchEs)
pOwEr cOrD lOcatiOns
For answers to your Monogram®, GE Profile™ Series
or GE® Series appliance questions, visit our website
at geappliances.com or call GE Answer Center®
service, 800.626.2000.
Specification Created 7/15
Page 3
A
B
4
GE Dryer Vent
B
2-1/2
GtD65GBsJ
GE® Series 7.4 Cu. Ft. Capacity Aluminized Alloy Drum
Gas Dryer with HE Sensor Dry
fOr cOmplEtE infOrmatiOn, sEE installatiOn instructiOns
packED with yOur DryEr.
DuctinG matErials:
For best performance, this dryer should be vented with 4" diameter all rigid metal
exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semirigid) ducting can be used (Kit WX08X10077). In special installations, it may be
necessary to connect the dryer to the house vent using a f lexible metal (foil-type) duct.
A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where
rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4"
diameter can be maintained throughout the entire length of the transition duct. Please
see installation instruction packed with your dryer for complete instructions when using
flexible metal (foil type) ducting.
Exhaust lEnGth calculatiOn:
1. Determine the number of 90° turns needed for your installation. If you exhaust to
the side or bottom of dryer, add one turn.
2. The maximum length of 4" rigid (aluminum or galvanized) duct which can be
tolerated is shown in the table. A turn of 45° or less may be ignored. Two 45° turns
within the duct length should be treated as a 90° elbow. A turn over 45° should be
treated as a 90° elbow.
Dryers must be exhausted to the outside.
cautiOn: For personal safety do not terminate exhaust into a chimney, under any
enclosed house f loor (crawl space), or into an attic, since the accumulated lint could
create a fire hazard or moisture could cause damage. Never terminate the exhaust into
a common duct or plenum with a kitchen exhaust, since the combination of lint and
grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts,
bird nesting, etc. The wall cap must also be located at least 12" above the ground or any
other obstruction with the opening pointed down.
fOr mOrE infOrmatiOn On vEntinG kits anD accEssOriEs, plEasE
call 1-800-GE-carEs.
For answers to your Monogram®, GE Profile™ Series
For answers to your Monogram,® GE Profile™
or GE® Series appliance questions, visit our website
or GE® appliance questions, visit our website
at geappliances.com or call GE Answer Center®
at geappliances.com or call GE Answer Center®
service, 800.626.2000.
service, 800.626.2000.
DryEr ExhaustinG infOrmatiOn—
usE mEtal Duct Only vErtical anD
hOrizOntal DuctinG
BEst pErfOrmancE
Maximum length
A
Number
of 90°
Domestic dryer models
GE Frontload Long Vent 7.0
cu. ft. capacity electric dryer
(GF DL)
Long Vent 6.0 - 8.0 cu. ft.
capacity electric & gas dryers
(GTDL and GT V)
Long Vent 6. 2-7.4 cu. ft.
capacity electric & gas
(GTD42, GTD45, GTD65,
GTX42 and GTX65)
All 6.0 - 8 .3 cu. f t. capacity
models electric and gas dryers
(GFDS, GFDR, GFDN, GTDS,
GTDN, GHDN, G HDS, GTDP,
GLDP, GTD, HTDP, HTDX)
DCVH480
All 3.6 cu. ft. (DSKS, DSKP)
electric dryers
Laundry Center GUD27
Laundry Center GUD24
of 4" dia rigid
metal duct
Exhaust hood type
A
turns
0 200 ft. 175 ft.
1 185 f t. 165 ft.
2 175 ft. 155 f t.
3 165 ft. 145 ft.
4 155 ft. 135 ft.
5 145 ft. 125 ft.
0 150 ft. 125 ft.
1 135 ft. 115 ft.
2 125 ft. 105 ft.
3 115 f t. 95 ft.
4 105 ft. 85 ft.
5 95 f t. 75 ft.
0 120 ft. 90 f t.
1 100 ft. 75 ft.
2 85 f t. 65 ft.
3 70 ft. 55 ft.
4 60 ft. 45 ft.
5 55 f t. 35 ft.
0 90 ft. 60 ft.
1 60 ft. 45 ft.
2 45 ft. 35 ft.
3 35 f t. 25 ft.
4 25 ft. 15 ft.
0 90 ft. 60 ft.
1 60 ft. 45 ft.
2 45 ft. 35 ft.
3 35 f t. 25 ft.
0 46 ft. 37 ft.
1 37 ft. 30 ft.
2 30 ft. 22 ft.
3 23 f t. 15 ft.
0 56 ft. 42 ft.
1 48 ft. 34 ft.
2 40 ft. 26 ft.
3 32 f t. 18 ft.
0 43 ft. 36 ft.
1 33 ft. 26 f t.
2 24 f t. 16 ft.
4"
opening
Specification Created 7/15
B
2-1/2"
opening
Page 4
GtD65GBsJ
GE® Series 7.4 Cu. Ft. Capacity Aluminized Alloy Drum Gas Dryer with HE Sensor Dry
fEaturEs anD BEnEfits
ENERGY STAR® qualified – Meets or exceeds federal guidelines for energy efficiency for
year-round energy and money savings
Up to 120 ft. venting capability – Provides flexible installation
Extended Tumble – Freshly tumbles your garments periodically for up to 8 hours when
unable to move clothing to the dryer right away
HE Sensor Dry – Keep your clothes looking and feeling their best. Dual thermistors
continually monitor temperature with a sensor bar that measures moisture to prevent
over-drying
My Cycle Settings – Dry clothes with the settings you prefer on any cycle, rather than the
defaults, and store your settings for later use
Damp Alert – Alerts you when clothes are the ideal dampness for ironing, for perfectly
wrinkle-free results
Model GTD65GBSJWS – White with silver backsplash
For answers to your Monogram®, GE Profile™ Series
or GE® Series appliance questions, visit our website
at geappliances.com or call GE Answer Center®
service, 800.626.2000.
Specification Created 7/15
Loading...