General Electric GFT14ESSLWW Use & Care

SAFETY INFORMATION ..........3

USING THE DRYER

Getting Started ...................... 4

Loading ..............................8

Features ..............................8

OWNER’S MANUAL &

INSTALLATION INSTRUCTIONS

GFT14

CARE AND CLEANING ...........9

INSTALLATION

INSTRUCTIONS .....................12

Stacking ...............................20

TROUBLESHOOTING TIPS ..... 24

CONSUMER SUPPORT

Warranty ........................... 27

Consumer Support ....................28

ENGLISH/FRANÇAIS/

ESPAÑOL

Write the model and serial numbers here:

Model # _________________

DRYERS

Serial # _________________

They are on the label on the front of the dryer behind the door.

GE is a trademark of the General Electric Company. Manufactured under trademark license.

0020507767P 49-90571-1 02-17 GEA

THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.

Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.

We take pride in the craftsmanship, innovation and design that goes into every GE Appliances

product, and we think you will too. Among other things, registration of your appliance ensures that we

can deliver important product information and warranty details when you need them.

Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration

card included in the packing material.

2 49-90571 -1

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

SAFETY INFORMATION

WARNING

Read all instructions before using the appliance.

DO NOT dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline,

dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode.

DO NOT place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a

chemical reaction that could cause a load to catch fire. To reduce the risk of fire due to contaminated loads, the final part of the tumble dryer cycle occurs without heat (cool down period). Avoid stopping a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.

DO NOT allow children to play on or in this appliance. Close supervision of children is necessary when this

appliance is used near children.

Before the appliance is removed from service or discarded, remove the door to the drying compartment.

DO NOT reach into the appliance if the drum is moving.

DO NOT install or store this appliance where it will be exposed to the weather.

DO NOT tamper with controls.

DO NOT repair or replace any part of this appliance or attempt any servicing unless specifically recommended

in t h e user-maintenance instructions or in published user-repair instructions that you understand and have the skills to carry out.

DO NOT use fabric softeners or products to eliminate static unless recommended by the manufacturer of the

fabric softener or product.

DO NOT dry articles containing foam rubber or similarly textured rubber-like materials.

Clean lint screen before or after each load.

DO NOT operate the dryer without the lint filter and condenser in place.

DO NOT store combustible materials, gasoline or other flammable liquids near the dryer. Keep area around the air

intake vent on the front of the dryer and adjacent surrounding areas free from the accumulation of lint, dust and dirt.

The interior of the appliance should be cleaned periodically by qualified service personnel.

Unplug the appliance or turn off the circuit breaker before servicing. Pressing the Power or Start/Pause button DOES

NOT disconnect power.

DO NOT operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or

broken parts, including a damaged cord or plug.

DO NOT spray any type of aerosol into, on or near dryer at any time. DO NOT use any type of spray cleaner when

cleaning dryer interior. Hazardous fumes or electrical shock could occur

See “ELECTRICAL CONNECTION” located in the Installation Instructions for grounding instructions.

To reduce the risk of fire, explosion, electric shock, or injury to persons when using your appliance,

follow basic precautions, including the following:

READ AND SAVE THESE INSTRUCTIONS

49-90571-1 3

Getting started

WARNING

To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY

INFORMATION before operating this appliance.

Throughout this manual, features and appearance may vary from your model.

Step 1

Step 2 Step 3

Power

• If the screen is dark, press the Power button

USING THE DRYER

• Loosely add items.

• Close door. NOTE: Dryer will not start

with door open.

to “wake up” the display.

• Select a dry cycle. (Defaults are set for each dry cycle. These default settings can be changed. See control settings for more information.)

Timed

Dry

• Press Timed Dry button, rotate knob to adjust time, and press Temp button to set your own temperature.

Step 4

Start

Pause

• Press the Start/Pause button.

Temp

Controls

K AJBL

DRY DAMP COOL

High

Medium

Low

No Heat

Temp

Ex Dry

Dry

Level

D E F G H I

Clean Filter

Empty Tank

Damp

Damp Timed

Timed

Damp

Alert

Dry

Est Time Remaining

Hold to Set

Tumble

Ext

Tumble

My Cycle

DelayDamp

Delay

Dry

C ottons

Heavy Duty

Towels

Casuals

Active Wear

Normal

Sanitize

Quick D ry

Deli cat es

De wrinkle

Rack Dr y

Warm Up

Start

Pause

Powe r

4 49-90571 -1

Getting started

Power

Press to “wake up” the display. If the display is active, press to turn the dryer off.

NOTE: Pressing Power does not disconnect the appliance from the power supply.

Dry Cycles

The dry cycle controls the cycle time for the drying process. The chart below will help you match the dry setting with the loads.

Normal For loads consisting of cottons and poly blends. Cottons For cottons and most linens. Heavy Duty For large coats, bed spreads, mattress covers, sleeping bags, blankets, comforters, jackets,

small rugs, and similar large and bulky items.

Towels Use for towels OR sheets. It is not recommended to mix towels and sheets in the same load. Casuals For wrinkle-free, permanent press and delicate items, and knits. Active Wear Clothing worn for active sports exercise and some casual wear. Fabrics include new technology

finishes and stretch fibers such as Spandex. Also for clothing labeled Easy Care or Perma Press: For wrinkle-free and permanent press items.

Sanitize Reduces certain types of bacteria by 99.6%, including: Staphylococcus aureus and Pseudomonas

aeruginosa. The antibacterial process occurs when high heat is used during a portion of this drying cycle.

USING THE DRYER

Quick Dry For small loads that are needed in a hurry, such as sports or school uniforms. Can also be

used if the previous cycle left some items damp, such as collars or waistbands.

Delicates For lingerie and special-care fabrics. Dewrinkle For removing wrinkles from items that are dry or slightly damp. This cycle is not recommended

for delicate fabrics.

Warm Up Provides 25 minutes of warming time to warm up clothes. Air Fluff Provides 30 minutes of tumbling time without heat. Rack Dry For drying delicate items without tumbling, use drying rack accessory. Place items flat on the

drying rack such as wool sweaters and delicate fabrics. Dry with low heat.

Temp

Temp (Temperature)

You can change the temperature of your dry cycle.

High For regular to heavy cottons. Medium For synthetics, blends and items labeled Permanent Press. Low For delicates, synthetics and items labeled Tumble Dry Low. No Heat This option may only be used with Air Fluff and Timed Dry, in which items are

tumbled without heat.

49-90571-1 5

Getting started

USING THE DRYER

Level

Damp

Alert

Timed

Dry

Level

The sensor continuously monitors the amount of moisture in the load. When the moisture in your clothes reaches your selected dry level, the dryer will stop.

NOTE: Sensor dry Level can be used with all cycles except Timed Dry, Air Fluff, Rack Dry, Warm Up and Dewrinkle.

Ex Dry Use for heavy-duty fabrics or items that should be very dry, such as towels. Dry Use for normal dryness level suitable for most loads. This is the preferred cycle

for energy saving.

Damp For leaving items partially damp.

Damp Alert

This option causes the dryer to beep when clothes have dried to a damp level. Remove items that you wish to hang dry. The Damp Alert will only beep when this option is selected, and the dryer will continue to dry.

Removing clothes and hanging them when they are damp can reduce the need to iron some items.

Timed Dry

1. Select the drying time by pressing the Timed Dry button. Rotate the knob to increase or

decrease the time in 10-minute increments up to 2 hours and 30 minutes.

2. Select the dry Temp.

3. Close the door.

4. Press Start/Pause.

My Cycle

Hold to Set

Ext

Tumble

My Cycle

Set up your favorite combination of settings and save them here for one touch recall. These custom settings can be set while a cycle is in progress.

To store a My Cycle combination of settings:

1. Select your drying cycle.

2. Change Temp and Level settings to fit your needs.

3. Select any drying options you want.

4. Press and hold the My Cycle button for 3 seconds to store your selection. A beep will sound and the button will light up.

To recall your stored My Cycle combination: Press the MY CYCLE button before drying a load.

To change your stored My Cycle combination:

Repeat steps 1–4.

Extended Tumble

Minimizes wrinkles by adding approximately 2 hours of no-heat tumbling after clothes are dry.

The estimated time remaining display will show “END”. The extended tumble time does not get added to the cycle time on the display.

6 49-90571 -1

Getting started

USING THE DRYER

Delay

Dry

Delay Dry

Use to delay the start of your dryer.

1. Choose your dry cycle and any options.

2. Press Delay Dry. You can change the delay time in 1 hour increments, using the Delay Dry button.

3. Press the Start/Pause button to start the countdown.

NOTE: If the door is opened while the dryer is in Delay Dry, the countdown time will not restart unless the door is closed and Start/Pause button has been pressed again.

Start/Pause

Temp

Start

Pause

Level

Press to start a cycle. If the dryer is running, pressing it once will pause the dryer and unlock the door. This function can be used to add garments during a cycle. Press again to restart the cycle.

NOTE: If the dryer is paused and the cycle is not restarted within 15 minutes, the current cycle will be cancelled.

Lock

You can lock the controls to prevent any selections from being made. Or you can lock or unlock the controls after you have started a cycle.

Children cannot accidentally start the dryer by touching pads with this option selected. To lock the dryer, press and hold the Temp and Level buttons together for 3 seconds. To unlock the dryer controls, press and hold the Temp and Level buttons together for 3

seconds. A sound is made to indicate the lock/unlock status. The control lock icon on the display will light up when it is on. NOTE: The Power button can still be used when the machine is locked.

Damp

Alert

DRY DAMP COOL

Ex Dry

High

Medium

Dry

Low

No Heat

Clean Filter

Empty Tank

Damp Timed

Damp DelayDamp

Timed

Dry

Est Time Remaining

My Cycle

Signal

When the light is on, the dryer will beep at the end of the cycle and every time you press a button on the control panel.

To turn the signal off, press and hold the Damp Alert and Timed Dry buttons together for 3 seconds. A sound is made to indicate the lock/unlock status.

Display and Status Lights

The display shows the approximate time remaining until the end of the cycle.

In addition, this display will show the dryer status:

Tumble

Status

Clean Filter Time to clean the filter. See the Care and Cleaning section. Empty Tank Time to empty the water tank. See the Care and Cleaning section.

Temp Shows High, Medium, Low or No Heat temperature setting selected. Level Shows Extra Dry, Dry or Damp dryness setting selected.

Damp Alert Indicates Damp Alert is set and will sound when the clothes have dried to a damp

Timed Indicates that a Timed Dry cycle is set. Will turn off after cycle is finished.

Est Time

Remaining

My Cycle Indicates the My Cycle feature is set.

Ext Tumble Indicates the Extended Tumble feature is set.

DRY DAMP COOL

Controls locked on. End of cycle signal on.

dryness level.

Display shows the estimated time remaining until set cycle is completed.

Indicates Delay Dry is set time is selected.

49-90571-1 7

Always follow fabric manufacturer’s care label when laundering.

Fabric Care Labels

Below are fabric care label “symbols” that affect the clothing you will be laundering.

Dry Labels

Tumble dry

Heat

USING THE DRYER

Dry

Normal

setting

High Medium Low No heat/air

Special instructions

Line dry/

hang to dry

Sorting and Loading Hints

Permanent Press/

wrinkle resistant

Drip dry

Dry flat

Gentle/

delicate

Do not tumble dry

In the shade

Do not dry (used with

do not wash)

WARNING

• Keep flammable materials and vapors, such as gasoline, away from dryer.

• DO NOT dry anything that has ever had anything flammable on it (even after washing).

• No washer can completely remove oil.

As a general rule, if clothes are sorted properly for the washer, they are sorted properly for the dryer. Try also to sort items according to size. For example, do not dry a sheet with socks or other small items.

Do not add fabric softener sheets once the load has become warm. They may cause fabric softener stains. Bounce® Fabric Conditioner Dryer Sheets have been approved for use in this dryer when used in accordance with the manufacturer’s instructions.

Do not overload. This wastes energy and causes wrinkling.

- Fire Hazard

• DO NOT dry anything that has ever had any type of oil

on it (including cooking oils).

• Items containing foam, rubber, or plastic must be dried on a clothesline.

• Failure to do so can result in death, explosion, or fire.

Drying Rack

A handy drying rack may be used for drying delicate items such as washable sweaters. Place items flat on the drying rack and block such items as wool sweaters and delicate fabrics. Dry with low heat.

To install the drying rack, extend the drying rack into the dryer drum. Rest the front two legs on the front angled ledge and then rest the rear two legs on the rear angled edge.

NOTES:

The drying rack is designed for use with the Timed Dry cycle. Use with sensor cycles

may result in damp items or extended cycle times.

Do not use this drying rack when there are other clothes in the dryer, that are not placed on the rack.

The drying rack, WE01X26416, is available as an accessory. Order on-line at GEApplianceParts.com, 24 hours

a day or by phone at 877.959.8688 during normal business hours.

8 49-90571 -1

Care and cleaning

Interior

The interior of the appliance should be cleaned once a year.

Exterior

Wipe or dust any spills or washing compounds with a damp cloth. Dryer control panel and finishes may be damaged by some laundry pretreatment soil and stain remover products. Apply these products away from the dryer. The fabric may then be washed and dried normally. Damage to your dryer caused by these products is not covered by your warranty.

Lint Filter

Clean the lint filter before each use. Pull out the lint filter. Moisten your fingers and remove the captured lint. Once clean, slide

the filter back into position. Have a qualified technician vacuum the lint from the dryer once a year.

NEVER OPERATE THE DRYER WITHOUT ITS FILTER IN PLACE.

Stainless Steel

To clean stainless steel surfaces use a damp cloth with a mild, non-abrasive cleaner suitable for stainless steel surfaces. Remove the cleaner residue and then dry with a clean cloth.

The stainless steel used to make the dryer drum provides the highest reliability available in a GE Appliances dryer. If the dryer drum should be scratched or dented during normal use, the drum will not rust or corrode. These surface blemishes will not affect the function or durability of the drum.

CARE AND CLEANING

Drum Lamp

NOTE: The drum lamp is not consumer replaceable on models where there is a domed

cover over an LED bulb. If this light should ever stop working, call for service.

For models that have a flat cover over the bulb secured by a screw:

Before replacing the light bulb, be sure to unplug the dryer power cord or disconnect the dryer at the household distribution panel by removing the fuse or switching off the circuit breaker. Reach above dryer opening from inside the drum to locate the light.

Remove the screw and the plastic cover to access the bulb. Replace with the appropriate bulb and then reaffix the cover and screw.

Order replacement bulb WE11X26351 on-line at GEApplianceParts.com, by phone at 877.959.8688 during normal business hours, or purchase appliance bulb 7C7 from your local retailer.

When the door is opened, the drum lamp automatically turns on and remains on for 2 minutes. When the door is closed, the drum lamp will remain on for 30 seconds.

49-90571-1 9

Care and cleaning

Water Tank

REMOVE THE CONDENSED WATER IN THE TANK AFTER EVERY DRYING CYCLE. NOTE: If drain hose is installed, emptying the water tank is not required. See the

CONNECTING THE DRAIN HOSE section in the Installation Installations of this manual.

• Pull out the water tank. When removing the water tank from the product, hold it using both hands

as it is heavy and take care not to spill any water inside the tank.

• Remove the condensed water inside the water tank. To avoid over filling, which could lead to water leaking outside the unit,

make sure to drain the water left in the water tank after each cycle. NOTE: When the Empty Tank indicator light is on, the dryer will not operate

until the tank is emptied and the indicator has been cleared. Press the Start button and the indicator light will turn off and the dryer will resume the cycle.

CARE AND CLEANING

Condenser

THE CONDENSER SHOULD BE CLEANED ONCE PER MONTH.

• Open the condenser compartment cover.

Drain hole on drawer

bottom

Unlock

• Unlock both locking tabs.

• Remove the condenser.

• Clean the condenser completely by allowing tap water to flow through it.

NOTES:

• Make sure to clean your condenser once per month to prevent degradation of the dryer’s performance.

• When assembling the condenser after cleaning it, make sure the locking tabs are set to the lock position. Never run the dryer without the condenser

installed.

10 49-90571 -1

Notes

NOTES

49-90571-1 11

Installation Instructions

If you have any questions, call GE Appliances at 800.GE.CARES (800.432.2737) In Canada, call 800.561.3344

or visit our Website at: GEAppliances.com

or visit www.GEAppliances.ca

Dryer

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT – Save these instructions for

local electrical inspector’s use.

• IMPORTANT – Observe all governing

codes and ordinances.

• Install the clothes dryer according to the manufacturer’s instructions and local codes.

• Note to Installer – Be sure to leave these instructions with the Consumer.

• Note to Consumer – Keep these instructions for future reference.

• Clothes dryer installation must be performed by a qualified installer.

• Before the old dryer is removed from service or discarded, remove the dryer door.

• Service information and the wiring diagram are located in the control console.

• Do not allow children on or in the appliance. Close supervision of children is necessary when the appliance is used near children.

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not covered under the Warranty.

• Install the dryer where the temperature is above 50°F for satisfactory operation of the dryer control system.

WARNING

• Clothes dryer installation must be performed by a qualified installer.

• Install the clothes dryer according to these instructions and local codes.

• DO NOT install or store this appliance in any location where it could be exposed to water or weather.

• To reduce the risk of severe injury or death, follow all installation instructions.

• Save these instructions. (Installers: Be sure to leave these instructions with the customer.)

If you are planning to stack the washer and dryer, order Stacking Kit number GFA24KITL to be used for this dryer. Kit sold separately.

- Fire Hazard

12 49-90571 -1

Installation Instructions

UNPACKING YOUR DRYER

Tilt the dryer sideways and remove the foam shipping pads by pulling at the sides and breaking them away from the dryer legs. Be sure to remove all of the foam pieces around the legs.

Remove the bag containing the literature.

DRYER DIMENSIONS

Front

View

23-7/16”

(59.5 cm)

*33-1/4” (84.5 cm)

42-13/16” (108.7 cm)

25-1/4” (64.1 cm)

*33-1/4” (84.5 cm)

*NOTE: With leveling legs retracted: 33-1/4 (84.5 cm) With leveling legs fully extended: 33-5/8 (85.4 cm) Stacked: 66-1/2” (168.9 cm)

ELECTRICAL CONNECTION DIMENSIONS

30”

(76.2 cm)

20-1/2”

(52.1 cm)

Back View

Side View

POWER CORDS

GE Appliances strongly recommends the use of factory specified parts. Select the power cord to fit your installation requirements.

Part Number Type Length Amperage

WX9X2 3-Prong 4 Feet 30 WX9X3 3-Prong 5 Feet 30

WX9X4 3-Prong 6 Feet 30 WX9X18 4-Prong 4 Feet 30 WX9X19 4-Prong 5 Feet 30 WX9X20 4-Prong 6 Feet 30

49-90571-1 13

Installation Instructions

REQUIREMENTS FOR ALCOVE OR CLOSET IN STALLATION

WARNING

Keep flammable materials and vapors, such as gasoline, away from dryer.

Place dryer at least 18” (46 cm) above the floor for a garage installation.

Failure to do so can result in death, explosion, or fire.

• Minimum clearance between dryer cabinet and adjacent walls or other surfaces is:

1” either side 3” front and rear 1” top

• Consideration must be given to provide adequate clearance for installation and service.

• Closet doors must be louvered or otherwise ventilated and have at least 60 square inches of open area. If the closet contains both a washer and a dryer, doors must contain a minimum of 120 square inches of open area.

- Explosion Hazard

MINIMUM CLEARANCE OTHER THAN ALCOVE OR CLOSET INSTALLATION

Minimum clearance to combustible surfaces and for air opening are: 1” both sides, 3” rear and 1” top. Consideration must be given to provide adequate clearance for installation and service.

MOBILE OR MANUFACTURED HOME INSTALLATION

• Installation MUST conform to the

MANUFACTURED HOME CONSTRUCTION AND SAFETY STANDARD, TITLE 24, PART 3280 or STANDARD FOR MOBILE HOMES CAN/CSA-Z240 MH, or, when such standards are not applicable, with AMERICAN NATIONAL STANDARD FOR MOBILE HOME, ANSI/NFPA NO. 501B.

• Provide an opening with a free area of at least 25

square inches for introduction of outside air into the dryer room.

• See the sections for electrical connection information.

BATHROOM OR BEDROOM INSTALLATION

The installation must conform with local codes or, in the absence of local codes, with the NATIONAL ELECTRICAL CODE, ANSI/NFPA NO. 70 (for electric dryers).

UNDERCOUNTER INSTALLATION

If an undercounter installation is desired:

• No special dryer installation kit is required.

• If the dryer is installed alone, a minimum of 60 square inches of open area is required. If a washer and dryer are installed together, a minimum of 120 square inches of open area is required.

Dryer Installed Alone

Countertop and side cabinets

square

inches

min.

open

area

Washer and Dryer Installed Together

Countertop and side cabinets

120

square

inches

min.

open

area

14 49-90571 -1

Installation Instructions

CONNECTING AN ELECTRIC DRYER

TOOLS YOU WILL NEED

Slip-joint pliers

Flat-blade screwdriver

Phillips screwdriver

Level

MATERIALS YOU WILL NEED

Safety glasses

Gloves

3/4” Strain relief (UL recognized)

Dryer power cord kit

(not provided with dryer) UL rated 120/240V, 30A with

3 or 4 prongs. Identify the plug type as per the house receptacle before purchasing line cord.

Stacking installations may require a power cord up to 6 feet in length.

Before making the electrical connection, turn off the circuit breaker(s) or remove the dryer’s circuit fuse(s) at the electrical box. Be sure the dryer cord is unplugged from the wall. NEVER LEAVE THE ACCESS COVER OFF THE TERMINAL BLOCK.

49-90571-1 15

Installation Instructions

ELECTRICAL CONNECTION INFORMATION FOR ELECTRIC DRYERS

For electrical connections using a power cord:

WARNING

Use a new UL-listed 240V 30 amp dryer power supply cord with closed ring terminals or spade terminals with upturned ends.

Use a UL-listed strain relief. Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center

terminal. Ground wire (green or bare wire) must be connected to

green ground connector. Connect remaining two supply wires to remaining two

terminals. Securely tighten all electrical connections. Replace the terminal block cover. Failure to do so can result in death, fire or electrical

shock.

- Fire Hazard

GROUNDING INSTRUCTIONS

For a grounded, cord-connected dryer: This dryer

must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This dryer uses a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

WARNING

result in a risk of electric shock. Check with a qualified electrician, or service representative or personnel, if you are in doubt as to whether the appliance is properly grounded. DO NOT modify the plug on the power supply cord. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

Improper connection of the equipment-grounding conductor can

ELECTRICAL CONNECTION INFORMATION FOR ELECTRIC DRYERS

For direct wire connections:

WARNING

Use 10 gauge copper wire. Use a UL-listed strain relief. Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center

terminal. Ground wire (green or bare wire) must be connected to

green ground connector. Connect remaining two supply wires to remaining two

terminals. Securely tighten all electrical connections. Replace the terminal block cover. Failure to do so can result in death, fire or electrical

shock.

- Fire Hazard

GROUNDING INSTRUCTIONS

For a permanently connected dryer: This dryer

must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal on the appliance.

WARNING

result in a risk of electric shock. Check with a qualified electrician, or service representative or personnel, if you are in doubt as to whether the appliance is properly grounded.

SAVE THESE INSTRUCTIONS

Improper connection of the equipment-grounding conductor can

16 49-90571 -1

Installation Instructions

CONNECTING DRYER USING 4-WIRE CONNECTION (MUST BE USED FOR MOBILE HOME INSTALLATION)

NOTE: Since January 1, 1996, the National Electrical

Code requires that new constructions use a 4 -w ir e connection to an electric dryer. A 4-wire cord must also be used where local codes do not permit grounding through the neutral. 3-wire connection is NOT for use on new construction.

Cover

Green wire from power cord

4 #10 AWG minimum copper conductors or 120/240V 30A power supply cord kit marked for use with dryers and provided with closed loop or spade terminals with upturned ends (not supplied)

1. Turn off the circuit breaker(s) (30 amp) or remove the dryer’s circuit fuse at the electrical box.

2. Be sure the dryer cord is unplugged from the wall receptacle.

3. Remove the power cord cover located at the upper back.

4. Remove green ground screw and retain for use in Ste p 7 . R e m o v e c e nt e r s c r e w ( ma r k e d N ) i n terminal block. Remove and discard ground strap.

5. Install 3/4 in. UL-recognized strain relief to power cord entry hole. Bring power cord through strain relief and bracket.

6. Connect power cord as follows:

A. Connect the 2 hot lines to the outer screws of the

terminal block (marked L1 and L2).

B. Connect the neutral (white) line to the center of

the terminal block (marked N).

7. Attach ground wire of power cord with the green ground screw (hole above strain relief bracket). Tighten all terminal block screws (3) securely.

8. Properly secure power cord to strain relief and bracket.

9. Reinstall the cover.

NEVER LEAVE THE COVER OFF OF THE TERMINAL BLOCK.

3/4” Strain Relief and Bracket

CONNECTING DRYER USING 3-WIRE CONNECTION

If required, by local code, install external ground (not provided) to grounded metal, cold water pipe, or other established ground determined by a qualified electrician.

Ground strap

Cover

3 #10 AWG minimum copper conductors or 120/240V 30A power supply cord kit marked for use with dryers and provided with closed loop or spade terminals with upturned ends (not supplied)

3-wire Connection

Not for use in Canada. DO NOT use for Mobile Home Installations. NOT for use on new construction. NOT for use on recreational vehicles. NOT for use in areas where local codes prohibit

grounding through the neutral conduction.

1. Turn off the circuit breaker(s) (30 amp) or remove the dryer’s circuit fuse at the electrical box.

2. Be sure the dryer cord is unplugged from the wall receptacle.

3. Remove the power cord cover located at the upper back.

4. Install 3/4-in. UL-recognized strain relief to power cord entry hole. Bring power cord through strain relief and bracket.

5. Connect power cord as follows:

A. Connect the 2 hot lines to the outer screws of

the terminal block (marked L1 and L2).

B. Connect the neutral (white) line to the center of

the terminal block (marked N).

6. Be sure ground strap is connected to green ground screw on cabinet rear. Tighten all terminal block screws (3) securely.

7. Properly secure power cord to strain relief and bracket.

8. Reinstall the cover.

NEVER LEAVE THE COVER OFF OF THE TERMINAL BLOCK.

3/4” Strain Relief and Bracket

49-90571-1 17

Installation Instructions

CONNECTING THE DRAIN HOSE

DRAINING WATER WITHOUT USING THE WATER TANK

You can use the dryer without using the water tank by following the procedures below.

CONNECTING THE DRAIN HOSE

The dryer can pump the condensed water outside of the DRYER directly with drain hose provide. The procedures to connect the drain hose are as follows.

Back View

CONNECTING THE DRAIN HOSE (CONT.)

4. Over the edge of a wash basin: The drain hose must

be placed lower than 58” (147 cm). To keep the drain hose spout bent, use the supplied plastic hose guide. Secure the guide to the wall with a hook or to the tap with a piece of string to prevent the drain hose from moving.

5. Assemble the drain hose and the hose guide and fix

them with the cable-tie.

Drain Hose

Hose Guide

58”

(147 cm)

Max.

Cable Ties

1. Disconnect the drain hose A.

2. Connect the drain hose A to

the other hole.

3. Connect accessory hose B

(long drain hose) adjacent to hose A.

• When connecting hose B, take care that the height of

the hose does not exceed 58” (147 cm).

• After connecting the drain hose, you can now

directly drain the condensed water to a standpipe or washstand.

Do not push the drain hose in the standpipe any further than 4” (10 cm). Pushing the drain hose further in the standpipe can cause leaking.

18 49-90571 -1

FINAL SETUP

Installation Instructions

LEVEL THE DRYER

Stand the dryer upright near the final location and adjust the four leveling legs at the corners to ensure that the dryer is level from side to side and front to rear.

Lower

PLUG DRYER IN

NOTE: Stacking installations may require a power

cord up to 6 feet in length.

Raise

DRYER STARTUP

Press the Power button.

Power

NOTE: If the dryer has been exposed to temperatures below freezing for an extended period of time, allow it to warm up before pressing Power. Otherwise, the display will not come on.

The dryer is now ready for use.

Ensure proper ground exists before use.

49-90571-1 19

Installation Instructions

STACKING THE WASHER AND DRYER (if desired)

If you are planning to stack the washer and dryer, order Stacking Kit number GFA24KITL to be used for this dryer. Kit sold separately.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT – Save these instructions for

local electrical inspector’s use.

• IMPORTANT – Observe all governing

codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions for

future reference.

• Service must be performed by a qualified installer.

• Do not allow children on or in the appliance. Close supervision of children is necessary when the appliance is used near children.

• Proper installation is the responsibility of the installer.

GE APPLIANCES STACK KIT

Order on-line at GEApplianceParts.com, 24 hours a day or by phone at 877.959.8688 during normal business hours.

Part Number Accessory GFA24KITL Complete Stack Kit

MINIMUM CLEARANCE OTHER THAN ALCOVE OR CLOSET INSTALLATION

Minimum clearance to combustible surfaces and for air opening are: 1” both sides, 3” rear and 1” top. Consideration must be given to provide adequate clearance for installation and service.

KIT CONTENTS (GE APPLIANCES KIT # GFA24KITL)

Screws (2) Long

For dryer

attachment

Bracketstack (L)

Bracketstack (R)

Screws (6) Short

For washer attachment

REQUIREMENTS FOR ALCOVE OR CLOSET IN STALLATION

WARNING

Keep flammable materials and vapors, such as gasoline, away from dryer.

Place dryer at least 18” (46 cm) above the floor for a garage installation.

Failure to do so can result in death, explosion, or fire.

• Minimum clearance between dryer cabinet and adjacent walls or other surfaces is:

1” either side 3” front and rear 1” top

• Consideration must be given to provide adequate clearance for installation and service.

- Explosion Hazard

TOOLS YOU WILL NEED

Phillips screwdriver

Level

Gloves

INSTALLATION PREPARATION

Remove the packaging. Flatten the product carton to use as a pad to lay the

dryer down on its side. Continue using the carton to protect the finished floor in front of the installation location.

20 49-90571 -1

Installation Instructions

INSTALLING THE STACK BRACKET KIT

INSTALL BRACKET TO WASHER

A. Remove washer top cap screw from the rear

left. Align left bracket holes with top cap screw hole on rear left of the unit and replace screw. NOTE: Leave screws loose so dryer hole alignment will be easier.

B. Drive next screw through the bracket into the

rear of the washer.

C. Repeat the above steps with the right side.

Short screws into

brackets and washer

Washer

Top

INSTALL DRYER AND BRACKET

ON DRYER

WARNING

serious injury or death.

Disconnect power before installing. Failure to do so could result in

INSTALL DRYER AND BRACKET

ON DRYER (CONT.)

C. Tighten the dryer bracket screws; then tighten all

stacking kit screws.

Long screws into

brackets and dryer

FINALIZE THE INSTALLATION

CAUTION

Pushing on the dryer may result in pinched fingers.

A. Refer to the washer Installation Instructions to

complete the washer installation.

B. Refer to the dryer Installation Instructions to

complete the dryer installation.

Do not push on the dryer once installed to top of the washer.

WARNING

Failure to do so may result in back or other injury, or property damage.

• Use two or more people to install dryer.

• Avoid tipping and rupture of utility services.

• Dryer must be securely attached to the washer.

• DO NOT place the washer on top of the dryer.

A. Lift the dryer on top of the washer. Protect the

washer control panel with cardboard or other protection. Be sure to lift the dryer high enough to clear the washer control panel.

B. Align the holes in the bracket with the holes in the

back of the dryer. Using a Phillips screwdriver, attach the 2 #8 x 1/2” tapping screws.

- Excessive Weight Hazard

C. Carefully slide or walk the stacked washer and

dryer into place. Use felt pads or other sliding device to assist moving and to protect flooring.

Dryer

Place

hands

here

Washer

Place

hands

here

49-90571-1 21

Notes

NOTES

22 49-90571 -1

Notes

NOTES

49-90571-1 23

Troubleshooting Tips... Before you call for service

Problem Possible Cause What To Do

Dryer shakes or makes noise

Clothes take too long to dry

TROUBLESHOOTING TIPS

The Dry dryness level was chosen but load is still damp

Control buttons not responding

Dryer doesn’t start

No numbers displayed during cycle, only lights

Some shaking/noise is normal. Dryer may be sitting unevenly.

Improper sorting Separate heavy items from lightweight items (generally, a

Large loads of heavy fabrics (like beach towels)

Non-venting dryer Condensing dryers usually take longer to dry than a vented dryer. Controls improperly set Match control settings to the load you are drying. Lint filter is full Clean lint filter before every load. Blown fuses or tripped

circuit breaker Overloading/combining loads Do not put more than one washer load in the dryer at a time. Underloading If you are drying only one or two items, add a few items to ensure

Load consists of a mixture of heavy and light fabrics

Lint filter, condenser, and/or air intake vent located on the front of the dryer is blocked

Dry Sensor is dirty Clean the sensor with a moist cloth. Controls accidentally put in

service mode Controls accidentally put in

lock mode Controls performed an

incorrect operation Control panel is “asleep” This is normal. Press Power to activate the control panel. Dryer is unplugged Make sure the dryer plug is pushed completely into the outlet. Fuse is blown/circuit breaker

is tripped Dryer was accidentally

paused when starting Delay Dry

Water tank is full If the Empty Tank light is on, you must empty the water tank

Dryer is continuously monitoring the amount of moisture in the clothes

Move dryer to an even floor space, or adjust leveling legs as necessary until even.

well-sorted washer load is a well-sorted dryer load). Large, heavy fabrics contain more moisture and take longer to dry.

Separate large, heavy fabrics into smaller loads to speed drying time.

Replace fuses or reset circuit breakers. Since most dryers use 2 fuses/breakers, make sure both are operating.

proper tumbling. When combining heavy and light fabrics in a load, choose More

Dry.

Inspect and clean lint filter, condenser, and/or air intake vent located on the front of the dryer.

Press Start/Pause.

Hold the Lock Control button for 3 seconds to unlock the dryer.

Reset the in-house breaker.

Check the building’s fuse/circuit breaker box and replace fuse or reset breaker. NOTE: Electric dryers use two fuses or breakers.

If the light on the Start/Pause button is flashing, the dryer is paused. Press Start/Pause to restart the countdown.

before the dryer will start. Refer to the Care and Cleaning section for instructions on emptying the water tank.

This is normal. When the dryer senses a low level of moisture in the load, the dryer will display the dry time remaining.

24 49-90571 -1

+ 56 hidden pages