GENERAL ELECTRIC GBSL0HCXLLS, GBSL0HCXRLS User Manual

ge.com

Refrigerators

Bottom Freezer

200D9366P004 49-60539 02-08 JR

Safety Instructions . . . . . . . . . . .2, 3

Operating Instructions

Automatic Icemaker . . . . . . . . . . . . . . .10

Care and Cleaning . . . . . . . . . . . . .11, 12

Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Crispers and Pans . . . . . . . . . . . . . . . . . . .7

Freezer . . . . . . . . . . . . . . . . . . . . . . . . . . .8, 9

Replacing the Light Bulbs . . . . . . . . . .13

Shelves and Bins . . . . . . . . . . . . . . . . . . . .6

Water Filter . . . . . . . . . . . . . . . . . . . . . . . . .5

Installation Instructions

Installing the Refrigerator . . . . . . .15–19

Installing the Water Line . . . . . . . .28–30

Preparing to Install

the Refrigerator . . . . . . . . . . . . . . . . . . . .14

Removing and Replacing the Doors (Double Door

Refrigerator Models only) . . . . . . .25–27

Removing and Replacing the

Freezer Drawer . . . . . . . . . . . . . . . . .20, 21

Reversing the Door Swing (Single Door Refrigerator

Models only) . . . . . . . . . . . . . . . . . . .22–25

Troubleshooting Tips . . . . . .31–34

Normal Operating Sounds . . . . . . . . . .31

Consumer Support

Consumer Support . . . . . . . .Back Cover

Performance Data Sheet . . . . . . . . . . .41

Product Registration

for Canadian Customers . . . . . . . .37, 38

Product Registration

for U.S. Customers . . . . . . . . . . . . .35, 36

State of California Water

Treatment Device Certificate . . . . . . .42

Warranty for Canadian

Customers . . . . . . . . . . . . . . . . . . . . . . . . .40

Warranty for U.S. Customers . . . . . . .39

Réfrigérateurs

Congélateur inférieur

Refrigeradores

Congelador inferior

Write the model and serial numbers here:

Model # ____________________ Serial #______________________

Find these numbers on a label on the right side, near the top of the refrigerator compartment.

Models 20, 22 and 23

Manuel d’utilisation

et d’installation

Owner’s Manual and

Installation Instructions

Manual del

propietario e

instalación

La section française commence à la page 43

La sección en español empieza en la página 81

IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

■

■ This refrigerator must be properly installed

and located in accordance with the Installation Instructions before it is used.

■

■ Do not allow children to climb, stand or hang

on the shelves in the refrigerator. They could damage the refrigerator and seriously injure themselves.

■

■ Do not touch the cold surfaces in the freezer

compartment when hands are damp or wet. Skin may stick to these extremely cold surfaces.

■

■ Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other appliance.

■

■ Keep fingers out of the “pinch point” areas;

clearances between the doors and between the doors and cabinet are necessarily small. Be careful closing doors when children are in the area.

■

■ In refrigerators with automatic icemakers,

avoid contact with the moving parts of the ejector mechanism, or with the heating element that releases the cubes. Do not place fingers or hands on the automatic icemaking mechanism while the refrigerator is plugged in.

■

■ Unplug the refrigerator before cleaning and making

repairs.

NOTE: We strongly recommend that any servicing be performed by a qualified individual.

■

■ Setting either or both controls to the Off position

does not remove power to the light circuit.

■

■ Do not refreeze frozen foods which have

thawed completely.

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous…even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow the instructions below to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may not

easily climb inside.

Refrigerants

All refrigeration products contain refrigerants, which under federal law must be removed prior to product disposal. If you are getting rid of an old refrigeration product, check with the company handling the disposal about what to do.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United States) or a CSA certified (in Canada), 3-wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

DANGER! RISK OF CHILD ENTRAPMENT

Consumer Support

Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

Consumer Support

Troubleshooting Tips

Operating InstructionsSafety Instructions

Installation

Instructions

ge.com

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.

Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.

The refrigerator should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate.

This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.

Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.

When moving the refrigerator away from the wall, be careful not to roll over or damage the power cord.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

USE OF ADAPTER PLUGS

Adapter plugs are not permitted in Canada.

About the controls with temperature settings.

Initially, set the refrigerator control at 5 and the freezer control at 5. Allow 24 hours for the temperature to stabilize. Several adjustments may be required. Adjust the controls one increment at a time, and allow 24 hours after each adjustment for the refrigerator to reach the temperature you have set.

Setting either or both controls to 0 for digital and 0 for the refrigerator control knob stops cooling in both the refrigerator and freezer compartments, but does not shut off electrical power to the refrigerator.

NOTE: The refrigerator is shipped with protective film covering the digital temperature controls. If this film was not removed during installation, remove it now.

Consumer Support

Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

(on some models)

Consumer Support

Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

Water Filter Cartridge

The water filter cartridge is located in the back upper right corner of the refrigerator compartment.

When to Replace the Filter

The filter cartridge should be replaced when the flow of water to the icemaker decreases, or every six months.

Installing the Filter Cartridge

If you are replacing the cartridge, first remove the old one. Open the cartridge cover by pressing in on the tab at the front and pulling down.

Remove the cartridge by slowly rotating it counterclockwise. A small amount of water may drip down.

CAUTION: If air has been

trapped in the system, the filter cartridge may be ejected as it is removed. Use caution when removing.

Remove the protective foil from the end of the cartridge.

Lining up the arrow on the cartridge and the cartridge holder, slowly rotate the cartridge clockwise until it stops. When the cartridge is properly installed, you will feel it “click” as it locks into place. The grip on the end of the cartridge should be positioned vertically. Do not overtighten.

Close the cartridge cover.

Filter Bypass Plug

You must use the filter bypass plug when a replacement filter cartridge is not available. The icemaker will not operate without the filter or filter bypass plug.

Replacement Filters: To order additional filter cartridges

in the United States, visit our Website, ge.com, or call GE Parts and Accessories,

800.626.2002.

Filter Model GSWF Customers in Canada should consult

the yellow pages for the nearest Mabe Service Center.

About the water filter. (on some models) ge.com

Consumer Support

Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

Rearranging the Shelves

To remove:

Remove all items from the shelf. Tilt the shelf up at the front. Lift the shelf up at the back and

bring the shelf out.

To replace:

While tilting the shelf up, insert the top hook at the back of the shelf in a slot on the track.

Lower the front of the shelf until the bottom of the shelf locks into place.

About the shelves and bins.

Not all features are on all models.

Some models have wire shelves that can be adjusted in the same manner.

Shelves in the refrigerator compartment are adjustable.

Refrigerator Compartment

Non-Adjustable Shelves on the Door (on some models)

To remove: Lift the shelf straight up; then

pull out. To replace: Engage the shelf in the molded

supports on the door and push down. It will lock in place.

Consumer Support

Troubleshooting Tips

Operating InstructionsSafety Instructions

Installation

Instructions

About the crispers and pans. ge.com

Not all features are on all models.

Fruit and Vegetable Crisper

Excess water that may accumulate in the bottom of the drawers or under the drawers should be wiped dry.

Adjustable Humidity Crisper (on some models)

Slide the control all the way to the HIGH setting to provide high humidity recommended for most vegetables.

Slide the control all the way to the LOW setting to provide lower humidity levels recommended for most fruits.

Snack Pan (on some models)

This pan can be moved to the most useful location for your family’s needs.

To remove, slide the pan out to the stop position, lift the pan up and past the stop position and lift it out.

Consumer Support

Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

Freezer Shelves and Baskets

A shelf above the ice storage bin A half-width basket A deep full-width basket

NOTE: Do not fill baskets higher than the rim of the basket. This may cause baskets to stick or jam when opening or closing.

Basket Removal

To remove the deep full-width basket on freezer drawer models:

Open the freezer drawer until it stops. The freezer basket rests on the inside

tabs on the drawer slides. Lift the basket so that it is out of all

6 slide bracket tabs. Tilt the basket and lift out of the drawer.

When replacing the deep full-width basket:

Tilt the basket back and lower it down into the drawer. Rotate the basket to a horizontal position and press it down into the 6 alignment tabs.

NOTE: Always be sure that the basket is seated in all 6 slide bracket tabs before sliding back into the freezer. The basket can be turned in either direction front to back and installed into the freezer.

To remove the half-width basket:

Pull the basket out to the stop location. Lift the basket up at the front to release

it from the stop hooks on each side. Lift the basket out to remove it from

the sides.

When replacing the basket, make sure that the basket goes under the stop hooks on each side.

NOTE: Always be sure to fully close this basket.

About the freezer drawer. (on some models)

Not all features are on all models.

Appearance and features may vary

Appearance may vary

Freezer Shelf and Basket

A full-width fixed wire shelf A full-width sliding wire basket

NOTE: Do not fill basket higher than the rim of the basket. This may cause basket to stick or jam when opening or closing.

Basket Removal

To remove the full-width sliding wire basket on door models:

Open the basket out to its full extension. Lift up the front of the basket and pull

straight out to remove.

When replacing the full-width sliding wire basket:

Insert the wire basket into the lower liner’s rails and push back into place.

NOTE: The full-width wire shelf is not intended to slide.

To remove for cleaning:

Hold the shelf at the front and pull it firmly forward.

When replacing the full-width sliding wire shelf:

Insert the wire shelf into the upper liner’s rails and push back into place.

About the freezer compartment. (on some models) ge.com

Not all features are on all models.

Fixed Shelf Removal

Consumer Support

Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

To remove: Lift the shelf straight up;

then pull out. To replace: Engage the shelf in the molded

supports on the door and push down. It will lock in place.

Non-Adjustable Shelf on Freezer Door

To remove

To replace

About the automatic icemaker. (on some models)

Automatic Icemaker

The icemaker will produce seven cubes per cycle— approximately 100–130 cubes in a 24-hour period, depending on freezer compartment temperature, room temperature, number of door openings and other use conditions.

See below for how to access ice and reach the power switch.

If the refrigerator is operated before the water connection is made to the icemaker, set the power switch in the O (off) position.

When the refrigerator has been connected to the water supply, set the power switch to the l (on) position. The icemaker power light will turn green when the freezer light switch is pressed in or when the freezer door is closed.

The icemaker will fill with water when it cools to 15°F (–10°C). A newly installed refrigerator may take 12 to 24 hours to begin making ice cubes.

You will hear a buzzing sound each time the icemaker fills with water.

Throw away the first few batches of ice to allow the water line to clear.

Be sure nothing interferes with the sweep of the feeler arm.

When the bin fills to the level of the feeler arm, the icemaker will stop producing ice. It is normal for several cubes to be joined together.

If ice is not used frequently, old ice cubes will become cloudy, taste stale and shrink.

NOTE: In homes with lower-than-average water pressure, you may hear the icemaker cycle multiple times when making one batch of ice.

NOTE: Set the power switch to the O (off) position if the water supply is shut off.

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

Icemaker

Feeler Arm

Power Switch

Green Power Light

Accessing Ice and Reaching the Power Switch

To reach the icemaker power switch, pull

the shelf above the ice bin straight out. Always be sure to replace the shelf.

To access ice, simply pull the bin forward.

To access ice.

Shelf

Ice Bin

To reach the power switch.

Shelf

Ice Bin

Icemaker Accessory Kit

If your refrigerator did not come already equipped with an automatic icemaker, an icemaker accessory kit is available at extra cost.

Check the back of the refrigerator for the specific icemaker kit needed for your model.

Consumer Support

Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

Care and cleaning of the refrigerator. ge.com

Cleaning the Outside

The door handles and trim. Clean with a

cloth dampened with soapy water. Dry with a soft cloth. Do not use wax on the door handles and trim.

Keep the outside clean. Wipe with a clean cloth lightly dampened with kitchen appliance wax or mild liquid dish detergent. Dry and polish with a clean, soft cloth.

Do not wipe the refrigerator with a soiled dish cloth or wet towel. These may leave a residue that can erode the paint. Do not use scouring pads, powdered cleaners, bleach or cleaners containing bleach because these products can scratch and weaken the paint finish.

The stainless steel panels and door handles. Stainless steel (on some models)

can be cleaned with a commercially available stainless steel cleaner. A spray-on stainless steel cleaner works best.

Do not use appliance wax or polish on the stainless steel.

Cleaning the Inside

To help prevent odors, leave an open box

of baking soda in the refrigerator and freezer compartments.

Unplug the refrigerator before cleaning.

If this is not practical, wring excess moisture out of sponge or cloth when cleaning around switches, lights or controls.

Use an appliance wax polish on the inside surface between the doors.

Use warm water and baking soda solution— about a tablespoon (15 ml) of baking soda to a quart (1 liter) of water. This both cleans and neutralizes odors. Rinse and wipe dry.

After cleaning the door gaskets, apply a thin layer of petroleum jelly to the door gaskets at the hinge side. This helps keep the gaskets from sticking and bending out of shape.

Avoid cleaning cold glass shelves with hot water because the extreme temperature difference may cause them to break. Handle glass shelves carefully. Bumping tempered glass can cause it to shatter.

Do not wash any plastic refrigerator parts in the dishwasher.

Consumer Support

Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

For long vacations or absences, remove food and unplug the refrigerator. Clean the interior with a baking soda solution of one tablespoon (15 ml) of baking soda to one quart (1 liter) of water. Leave the doors open.

Set the icemaker power switch to the O (off) position and shut off the water supply to the refrigerator.

If the temperature can drop below freezing, have a qualified servicer drain the water supply system (on some models) to prevent serious property damage due to flooding.

Care and cleaning of the refrigerator.

Preparing for Vacation

Preparing to Move

Secure all loose items such as base grille, shelves and drawers by taping them securely in place to prevent damage.

When using a hand truck to move the refrigerator, do not rest the front or back of the refrigerator against the hand truck. This could damage the refrigerator. Handle only from the sides of the refrigerator.

Be sure the refrigerator stays in an upright position during moving.

Behind the Refrigerator

Be careful when moving the refrigerator away from the wall. All types of floor coverings can be damaged, particularly cushioned coverings and those with embossed surfaces.

Raise the leveling legs located at the bottom front of the refrigerator.

Pull the refrigerator straight out and return it to position by pushing it straight in. Moving

the refrigerator in a side direction may result in damage to the floor covering or refrigerator.

Lower the leveling legs until they touch the floor.

When pushing the refrigerator back, make sure you don’t roll over the power cord or icemaker supply line (on some models).

Consumer Support

Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

Refrigerator Lights

CAUTION: Light bulbs may

be hot.

Unplug the refrigerator.

To remove the light shield, grasp the shield at the back and pull out to release the tabs at the back.

Rotate the shield down and then forward to release the tabs at the front of the shield.

After replacing with an appliance bulb of the same or lower wattage, replace the shield.

Plug the refrigerator back in.

NOTE: Appliance bulbs may be ordered from GE Parts and Accessories, 800.626.2002.

Freezer Light

Replacing the light bulbs. ge.com

Turning the control to the 0ff position does not remove power to the light circuit.

Appearance may vary

CAUTION: Light bulbs may

be hot.

Unplug the refrigerator.

The bulb is located at the top of the freezer inside a light shield. To remove the shield, grasp the shield at the back and pull out to release the tabs at the back.

Rotate the shield down and then forward to release the tabs at the front of the shield.

After replacing with an appliance bulb of the same or lower wattage, replace the shield.

Plug the refrigerator back in.

Consumer Support

Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

Installation

Refrigerator

Instructions

Models 20 and 22

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com

In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT — Save these instructions

for local inspector’s use.

•

IMPORTANT — Observe all governing

codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions for

future reference.

• Skill level – Installation of this appliance requires

basic mechanical skills.

• Completion time – Refrigerator Installation

20 minutes Water Line Installation

30 minutes

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is not

covered under the Warranty.

PREPARATION

MOVING THE REFRIGERATOR INDOORS If the refrigerator will not fit through a doorway,

the refrigerator door and freezer drawer can be removed.

• To remove the refrigerator door, see Step 1 in

the Reversing the Door Swing section.

• To remove the freezer drawer, see the Removing

the Freezer Drawer section.

WATER SUPPLY TO THE ICEMAKER AND DISPENSER (ON SOME MODELS)

If the refrigerator has an icemaker, it will have to be connected to a cold water line. A GE water supply kit (containing tubing, shutoff valve, fittings and instructions) is available at extra cost from your dealer, by visiting our Website at ge.com (in Canada at www.geappliances.ca) or from Parts and Accessories, 800.626.2002 (In Canada 1.888.661.1616).

TOOLS YOU MAY NEED

Adjustable Wrench

1/4″ Outer Diameter

Compression Nut

and Ferrule (sleeve)

(icemaker models only)

Phillips Head Screwdriver

3/8″ and 5/16″ Socket

Ratchet/Driver

3/32″, 1/8″ and 3/16″ Allen

wrenches

Pencil

1/8″ Drill Bit and Electric or Hand Drill

Tape measure

1/4″ Nut Driver

Wire Cutters

Level

Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

• Do not install the refrigerator where the temperature

will go below 60°F (16°C) because it will not run often enough to maintain proper temperatures.

• Do not install the refrigerator where the temperature

will go above 100°F (37°C) because it will not perform properly.

• Install it on a floor strong enough to support it fully

loaded.

CLEARANCES

Allow the following clearances for ease of installation, proper air circulation and plumbing and electrical connections.

Standard Depth

Models Sides 1/8″ (3 mm) Top 1″ (25 mm) Back 1″ (25 mm)

CONNECTING THE REFRIGERATOR TO THE HOUSE WATER LINE

(icemaker models)

A cold water supply is required for automatic icemaker operation. If there is not a cold water supply, you will need to provide one. See Installing the Water Line section.

NOTES:

• Before making the connection to the refrigerator,

be sure the refrigerator power cord is not plugged into the wall outlet.

• If your refrigerator does not have a water filter, we

recommend installing one if your water supply has sand or particles that could clog the screen of the refrigerator’s water valve. Install it in the water line near the refrigerator. If using GE SmartConnect

™

Refrigerator Tubing Kit, you will need an additional tube (WX08X10002) to connect the filter. Do not cut plastic tube to install filter.

REMOVE TOP CAP (on some models)

•

IMPORTANT NOTE: This refrigerator is 34-1/2″ deep. Doors and passageways leading to the installation location must be at least 36″ wide in order to leave the doors and handles attached to the refrigerator while transporting it into the installation location. If passageways are less than 36″, the refrigerator doors and handles can easily be scratched and damaged. The top cap and doors can be removed to allow the refrigerator to be safely moved indoors. Start with Step A.

•If it is not necessary to remove doors, skip Step A. Leave tape and all packaging on doors until the refrigerator is in the final location.

•SKID REMOVAL: Tilt refrigerator to each side to remove skid.

•NOTE: Use a padded hand truck to move this refrigerator. Place the refrigerator on the hand truck with a side against the truck. We strongly recommend that TWO PEOPLE move and complete this installation.

Locate and remove the two Phillips head screws on the top of the refrigerator. Remove the two screws on each side at the rear of the top cap. Lift off and remove top cap.

Remove the fresh-food door(s). Refer to Steps 1 and 3 of “Reversing the Door Swing” section or Steps 1 and 2 of “Removing the Doors” section.

Remove the bottom freezer drawer or door. Refer to “Removing Freezer Drawer” section or Step 2 of “Reversing the Door Swing” section.

Move refrigerator to the installation location.

REMOVE TOP CAP (cont.) (on some models)

REINSTALL DOORS, DRAWERS AND TOP CAP

Carefully lower the door(s) onto the center hinge(s). Reinstall top hinge(s). NOTE: Ensure the door is properly aligned to the case top to avoid readjustment of the door during top cap reinstallation.

Place cap over the top of the refrigerator. Reinstall the original screws in the top and back of the cap.

Reinstall the bottom freezer drawer or door. Refer to “Replacing the Freezer Drawer” section or Step 8 of “Reversing the Door Swing” section.

Top Hinge B

CONNECTING THE REFRIGERATOR TO THE HOUSE WATER LINE (cont.)

If you are using copper tubing, place a

compression nut and ferrule (sleeve) onto the end of the tubing coming from the house cold water supply.

If you are using the GE SmartConnect

™

tubing, the nuts are already assembled to

the tubing. If you are using copper tubing, insert

the end of the tubing into the refrigerator connection, at the back of the refrigerator, as far as possible. While holding the tubing, tighten the fitting.

If you are using GE SmartConnect

™

tubing,

insert the molded end of the tubing into the refrigerator connection, at the back of the refrigerator, and tighten the compression nut until it is hand tight. Then tighten one additional turn with a wrench. Overtightening may cause leaks.

Fasten the tubing into the clamp provided to hold it in position. You may need to pry open the clamp.

One of the illustrations below will look like the connection on your refrigerator.

Icemaker-Ready models

Icemaker-Installed Models

Installation Instructions

1/4″ Tubing

Tubing Clamp

1/4″ Compression Nut

Ferrule (sleeve)

SmartConnect

™

Tubing

Refrigerator Connection

TURN ON THE WATER SUPPLY

(icemaker models)

Turn the water on at the shutoff valve (house water supply) and check for any leaks.

PLUG IN THE REFRIGERATOR

On models with an icemaker, before plugging in the refrigerator, make sure the icemaker power switch is set to the O (off) position.

See the grounding information attached to the power cord.

PUT THE REFRIGERATOR IN PLACE

Move the refrigerator to its final location.

1/4″ Copper Tubing

1/4″ Compression Nut

Ferrule (sleeve)

SmartConnect

™

Tubing

Refrigerator Connection

Tubing Clamp

LEVEL THE REFRIGERATOR

Adjustable legs at the front corners of the

refrigerator should be set so the refrigerator is firmly positioned on the floor, and the front is raised just enough that the door closes easily when opened about halfway.

To adjust the leveling legs, turn the legs clockwise to raise the refrigerator, counterclockwise to lower it.

INSTALLING THE REFRIGERATOR (cont.)

Installation Instructions

REMOVE THE FRESH FOOD DOOR HANDLE

(For placement in the installation location or reversal of the handles – on some models)

Stainless steel (on some models):

REMOVING THE DOOR HANDLE: Loosen the set screws with the 3/32″ Allen wrench and remove the handle. NOTE: For Double Door models follow the same procedure on the opposite door.

Plastic handle (on some models):

REMOVING THE DOOR HANDLE: Depress the tab on the underside of the handle and slide the handle up and off of the mounting fasteners.

REVERSING THE DOOR HANDLE (on some models):

• Remove

the handle mounting fasteners with a 3/16″ Allen wrench and transfer the handle mounting fasteners to the right side.

• Remove the logo badge.

• Remove and transfer the plug button to

the left side of the fresh food door. NOTE: Use a flat plastic edge to prevent damaging the door. Remove any adhesive on the door with a mild detergent. Remove the paper covering on the adhesive backing on the logo badge prior to carefully attaching the badge to the door.

Mounting Fasteners

Badge

(appearance may vary)

REMOVE THE FREEZER DOOR HANDLE

Stainless steel and plastic handles:

Loosen the set screws located on the underside of the handle with the 1/8″ Allen wrench and remove the handle.

NOTE: If the handle mounting fasteners need to be tightened or removed, use a 3/16″ Allen wrench.

ATTACH THE FREEZER DOOR HANDLE

Stainless steel and plastic handles:

Attach the handle firmly to the mounting fasteners and tighten the set screws on the bottom of the handle with a 1/8″ Allen wrench.

Installation Instructions

ATTACH THE FRESH FOOD DOOR HANDLE

Stainless steel handle:

Attach the handle to the handle mounting fasteners and tighten the set screws with a 3/32″ Allen wrench. NOTE: For Double Door models follow the same procedure on the opposite door.

Plastic handle:

Attach the handle to the handle mounting fasteners by aligning the slots with the handle mounting fasteners.

Slide it down until it is firmly locked into position.

Mounting Fasteners

(appearance may vary)

Mounting fasteners

Slots on back of handle

(appearance may vary)

INSTALLING THE REFRIGERATOR (cont.)

LEVEL THE REFRIGERATOR

The leveling legs have 2 purposes:

1) Leveling legs adjust so the refrigerator is

firmly positioned on the floor and does not wobble.

2) Leveling legs serve as a stabilizing brake

to hold the refrigerator securely in position during operation and cleaning. The leveling legs also prevent the refrigerator from tipping.

Remove the grille by removing the two Phillips head screws.

Turn the leveling legs clockwise to raise the refrigerator, counterclockwise to lower it.

CAUTION: To avoid possible

personal injury or property damage, the leveling legs must be firmly touching the floor.

Replace the base grille by inserting the two Phillips head screws.

Installation Instructions

SET THE CONTROLS

Set the controls to the recommended setting.

REMOVE PACKAGING, START ICEMAKER

(icemaker models)

A) Remove all tape, foam and protective

packing from shelves and drawers.

B) Remove the tie downs from the freezer

baskets.

C) Place half width basket onto drawer slides.

See About the freezer section for instructions.

Set the icemaker power switch to the I (on) position. The icemaker will not begin to operate until it reaches its operating temperature of 15°F (–9°C) or below. It will then begin operation automatically. It will take 2–3 days to fill the ice bin.

NOTE: In lower water pressure conditions, the water valve may turn on up to 3 times to deliver enough water to the icemaker.

Power switch

Installation Instructions

REMOVE THE BASE GRILLE

(if needed)

If, after removing the freezer drawer and refrigerator door, the refrigerator will still not fit through a doorway, the base grille can be removed.

Remove the base grille by removing the screws.

REMOVING THE FREEZER DRAWER (on some models)

REMOVE THE BASKET

Open the freezer drawer until it stops. The freezer basket rests on a frame inside the

freezer drawer. Lift the basket up at the back. Lift the front up and lift the entire basket up

and out of the drawer.

A B

The freezer drawer can be removed, if needed, to fit through tight areas.

Read these instructions completely and carefully.

REMOVE THE DRAWER FRONT

Remove the screw on each side of the railing.

REMOVE THE DRAWER FRONT (cont.)

Lift up on both sides of the freezer drawer handle to separate the drawer railings from the rail assemblies.

Set the drawer front on a non-scratching surface.

Push the rail assemblies back into locking position.

Rail Assembly

Drawer Assembly

Screw

Installation Instructions

REPLACING THE FREEZER DRAWER (on some models)

ATTACH AND SECURE THE DRAWER FRONT TO THE SLIDES

Pull out the rail assemblies to the full length on each side of the cabinet.

Locate the slots on the inside of the rail assemblies near the back.

Insert the hooks at the back of the drawer railings into the slots on the rail assemblies.

Lower the front of the drawer, making sure the tabs on the sides of the railings fit into the front slots in the rail assemblies.

REPLACE THE FREEZER BASKET

Replace the lower freezer basket by lowering it into the frame.

Two people may be required to complete this procedure.

ATTACH AND SECURE THE DRAWER FRONT TO THE SLIDES

(cont.)

Replace the screws on both rail assemblies.

Slot

Rail assembly

Slot

Tab

Hook

Screw

TOOLS YOU WILL NEED

Installation Instructions

REVERSING THE DOOR SWING (Single Door Refrigerator Models only)

IMPORTANT NOTES

When reversing the door swing: NOTE: Door swing is not reversible on stainless

steel models.

• Read the instructions all the way through before

starting.

• Parts are included in the door hinge kit.

• Handle parts carefully to avoid scratching paint.

• Set screws down by their related parts to avoid

using them in the wrong places.

• Provide a non-scratching work surface for

the doors.

IMPORTANT: Once you begin, do not move the cabinet until door-swing reversal is completed.

These instructions are for changing the hinges from the right side to the left side—if you ever want to change the hinges back to the right side, follow these same instructions and reverse all references to left and right.

• Once door swing is finalized, ensure the logo

badge is properly aligned and permanently secured to the door by removing the adhesive cover on the back side. NOTE: A replacement logo badge is included in the hinge kit.

Unplug the refrigerator from its electrical outlet. Empty all door shelves, including the dairy

compartment.

Thin-blade Screwdriver

Masking Tape

Adjustable Wrench

5/16

″ Socket

Ratchet/Driver

REMOVE THE REFRIGERATOR DOOR

Tape the door shut with masking tape.

Remove the hinge cover on top of the refrigerator door by carefully prying it up with a putty knife, if necessary.

Using a 5/16″ socket ratchet/driver, remove the bolts securing the top hinge to the cabinet. Then lift the hinge straight up to free the hinge pin from the socket in the top of the door.

Carefully remove the door thimble from inside the socket. This will be used again when reinstalling the door on the other side.

Remove the tape and tilt the door away from the cabinet. Lift the door off the center hinge pin. Ensure that the plastic hinge pin thimble remains on the hinge pin or inside door hinge pin hole located in the bottom of the door.

Set the door on a non-scratching surface with the inside up.

Hinge Cover

Top Hinge

Phillips Screwdriver

Torx T-20 Driver

Door Thimble

Installation Instructions

TRANSFER CENTER HINGE

BRACKET

(cont.)

Transfer the plug button and screw hole cover in the hinge holes on the left side to the right side.

Install the new center hinge bracket from the kit on the left side.

REMOVE THE FREEZER DOOR

Tape the door shut with masking tape. Remove hinge pin from hinge bracket. This will

be used again with the new hinge bracket for the other side.

Remove the tape and tilt the door away from the cabinet. Lift the door off the bottom hinge pin.

Remove the button plug from the left side of the door. Remove the door thimble from the right side of the door. Install the door thimble into the hole on the left and the button plug into the hole on the right.

Set the door on a non-scratching surface, with the inside up.

A B

TRANSFER CENTER HINGE BRACKET

Using a 5/16″ socket ratchet/driver, remove the bolts securing the center hinge to the cabinet.

REMOVE BOTTOM HINGE AND LEVELING LEG

Using a 1/2″ socket ratchet/driver, remove the nut and hinge pin from the hinge bracket with leveling leg. Using a 5/16″ socket ratchet/driver, remove the screws from the bottom hinge bracket. These will be reinstalled on the other side.

Using a 5/16″ socket ratchet/driver, remove the screws from the leveling leg bracket on the other side. These will be reinstalled on the opposite side.

Bottom Hinge Bracket

Leveling Leg Bracket

TRANSFER REFRIGERATOR AND FREEZER DOOR STOPS

Remove the door stop on the right side of the bottom of the door by removing the two screws.

Move the plastic hinge hole thimble to the opposite hole.

Install the door stop on the left side, making sure to line up the screw holes in the door stop with the holes in the bottom of the door.

Bottom of Door (Right Side) Bottom of Door (Left Side)

TRANSFER REFRIGERATOR DOOR HANDLE TO RIGHT

Refer to Remove the Fresh Food Door Handle and Attach the Fresh Food Door Handle sections for instructions.

Installation Instructions

INSTALL BOTTOM HINGE AND LEVELING LEG

Using a 1/2″ socket ratchet/driver, install the hinge pin and nut in the opposite hole on the hinge bracket with leveling leg.

Using a 5/16″ socket ratchet/driver, install the hinge bracket with leveling leg on the left side of the refrigerator. The pin will be toward the outside of the refrigerator.

Using a 5/16″ socket ratchet/driver, install the leveling leg bracket on the right side of the refrigerator.

REHANG FREEZER DOOR

Lower the freezer door onto the bottom hinge pin. Ensure that the plastic hinge pin thimble is on the hinge pin or inside the door hinge pin hole located in the bottom of the door.

Straighten the door and line it up with the center hinge bracket.

Install the center hinge pin with a 3/4″ socket ratchet/driver. Turn it until it extends through the hinge bracket and into the freezer door.

REVERSING THE DOOR SWING (cont.)

Installation Instructions

REMOVING THE DOORS

(Double Door Refrigerator Models only)

IMPORTANT NOTES

NOTE: Door swing is not reversible.

• Read the instructions all the way through before

starting.

• Handle parts carefully to avoid scratching paint.

• Set screws down by their related parts to avoid

using them in the wrong places.

• Provide a non-scratching work surface for

the doors.

IMPORTANT: Once you begin, do not move the cabinet.

These instructions are for removing the doors.

Unplug the refrigerator from its electrical outlet. Empty all door shelves, including the dairy

compartment.

TOOLS YOU WILL NEED

Thin-blade Screwdriver

Masking Tape

Adjustable Wrench

3/8

″ and 10 mm Socket

Ratchet/Driver

Phillips Screwdriver

REHANG REFRIGERATOR DOOR

Lower the refrigerator door onto the center hinge pin. Ensure that the plastic hinge pin thimble is on the center hinge pin or inside door hinge pin hole located in the bottom of the door.

Insert the door thimble into the hinge hole on top of the refrigerator door and then insert the top hinge pin. Make sure the door is aligned with the cabinet. Attach the hinge to the top of the cabinet loosely with the bolts.

Make sure the gasket on the door is flush against the cabinet and is not folded. Support the door on the handle side and make sure the door is straight and the gap between the doors is even across the front. While holding the door in place, tighten the top hinge bolts. Replace the hinge cover.

INSTALL THE LOGO BADGE

Remove the adhesive backing paper and align the pins on the back of the badge with the holes in the door. Apply pressure to the badge to ensure it sticks to the door.

REMOVE THE REFRIGERATOR DOORS (cont.)

Set the door on a non-scratching surface with the inside up.

Installation Instructions

REMOVE OPPOSITE DOOR

Follow the same procedure on the opposite door. There are no center hinge covers on the opposite side.

REMOVE FREEZER DRAWER

Refer to the Removing the Freezer Drawer section for instructions.

REMOVE THE REFRIGERATOR DOORS

Tape the doors shut with masking tape.

Start with left-hand door first: Remove the screw securing the center hinge cover, lift the hinge cover and place to the side on top of the refrigerator.

Remove the hinge cover on top of the refrigerator door by removing the Phillips head screw and pulling the cover up.

Using a 5/16″ socket ratchet/driver, remove the bolts securing the top hinge to the cabinet. Then lift the hinge straight up to free the hinge pin from the socket in the top of the door.

Remove hinge cover (1 Phillips screw)

REMOVE CENTER HINGE

Using a 5/16″ socket ratchet/driver, remove the bolts securing the center hinge to the cabinet. Set the hinge and bolts aside.

Hinge Cover

Top Hinge

REMOVING THE DOORS (Double Door Refrigerator Models only)

Installation Instructions

REPLACING THE DOORS (Double Door Refrigerator Models only)

INSTALL CENTER HINGE

Install the center hinge on each side.

REHANG REFRIGERATOR DOORS

Lower the refrigerator door onto the center hinge pin. Ensure that the plastic hinge pin thimble is on the center hinge pin or inside door hinge pin hole located in the bottom of the door.

Securely tape the door shut with masking tape or have a second person support the door.

Insert the top hinge pin into the hinge hole on top of the refrigerator door. Make sure the door is aligned with the cabinet and opposite door. Attach the hinge to the top of the cabinet loosely with the bolts.

Make sure the gasket on the door is flush against the cabinet and is not folded. Make sure the door is straight and the gap between the doors is even across the front. While holding the aligned door in place, tighten the top hinge bolts. Replace the hinge cover and screw.

Hinge Pin

ALIGN DOUBLE DOORS

If the top of the doors are uneven, first try to raise the lowest door by turning the leveling leg on the same side as the door until the doors are even. If the unit rocks, re-adjust the leveling legs to the extent that the unit is stable.

If the doors remain uneven, turn the adjustable pin to raise, or lower, the left door to match the right door. Use a 1/4″ Allen wrench to turn the pin.

Adjustable pin

REPLACE FREEZER DRAWER

Refer to the Replacing the Freezer Drawer section for instructions.

REPLACE OPPOSITE DOOR

Follow the same procedure on the opposite door. There is no water line or hinge cover.

Top Hinge Bolts

Hinge Cover

(appearance may vary)

Installation Instructions

INSTALLING THE WATER LINE (ICEMAKER MODELS)

Recommended copper water supply kits are WX8X2, WX8X3 or WX8X4, depending on the amount of tubing you need. Approved plastic water supply lines are GE SmartConnect

™

Refrigerator Tubing (WX08X10006, WX08X10015 and WX08X10025).

When connecting your refrigerator to a GE Reverse Osmosis Water System, the only approved installation is with a GE RVKit. For other reverse osmosis water systems, follow the manufacturer’s recommendations.

If the water supply to the refrigerator is from a Reverse Osmosis Water Filtration System AND the refrigerator also has a water filter, use the refrigerator’s filter bypass plug. Using the refrigerator’s water filtration cartridge in conjunction with the RO filter can result in hollow ice cubes.

This water line installation is not warranted by the refrigerator or icemaker manufacturer. Follow these instructions carefully to minimize the risk of expensive water damage.

Water hammer (water banging in the pipes) in house plumbing can cause damage to refrigerator parts and lead to water leakage or flooding. Call a qualified plumber to correct water hammer before installing the water supply line to the refrigerator.

To prevent burns and product damage, do not hook up the water line to the hot water line.

If you use your refrigerator before connecting the water line, make sure the icemaker power switch is in the O (off) position.

Do not install the icemaker tubing in areas where temperatures fall below freezing.

When using any electrical device (such as a power drill) during installation, be sure the device is double insulated or grounded in a manner to prevent the hazard of electric shock, or is battery powered.

All installations must be in accordance with local plumbing code requirements.

BEFORE YOU BEGIN

WHAT YOU WILL NEED

• Copper or GE SmartConnect™Refrigerator Tubing kit, 1/4″ outer diameter to connect the

refrigerator to the water supply. If using copper, be sure both ends of the tubing are cut square.

To determine how much tubing you need: measure the distance from the water valve on the back of the refrigerator to the water supply pipe. Be sure there is sufficient extra tubing to allow the refrigerator to move out from the wall after installation.

GE SmartConnect

™

Refrigerator Tubing Kits

are available in the following lengths: 6′ (1.8 m) – WX08X10006

15′ (4.6 m) – WX08X10015 25′ (7.6 m) – WX08X10025

NOTE: The only GE approved plastic tubing is that supplied in GE SmartConnect

™

Refrigerator Tubing kits. Do not use any other plastic water supply line because the line is under pressure at all times. Certain types of plastic will crack or rupture with age and cause water damage to your home.

• A GE water supply kit (containing tubing,

shutoff valve and fittings listed below) is available at extra cost from your dealer or from Parts and Accessories, 800.626.2002 (in Canada

1.888.261.3055).

• A cold water supply. The water pressure must

be between 20 and 120 p.s.i. (1.4–8.1 bar).

• Power drill.

• 1/2″ or adjustable wrench.

• Straight and Phillips blade screwdriver.

• Two 1/4″ outer diameter compression nuts and 2 ferrules (sleeves)—to connect the copper

tubing to the shutoff valve and the refrigerator water valve.

• If you are using a GE SmartConnect

™

Refrigerator Tubing kit, the necessary fittings are preassembled to the tubing.

• If your existing copper water line has a flared fitting at the end, you will need an adapter (available at plumbing supply stores) to connect the water line to the refrigerator OR you can cut off the flared fitting with a tube cutter and then use a compression fitting. Do not cut formed end from GE SmartConnect

™

Refrigerator tubing.

• Shutoff valve to connect to the cold water line. The shutoff valve should have a water inlet with a minimum inside diameter of 5/32″ at the point of connection to the COLD WATER LINE. Saddle- type shutoff valves are included in many water supply kits. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes.

WHAT YOU WILL NEED (CONT.)

SHUT OFF THE MAIN WATER SUPPLY

Turn on the nearest faucet long enough to clear the line of water.

Install the shutoff valve on the nearest frequently used drinking water line.

Choose a location for the valve that is easily accessible. It is best to connect into the side of a vertical water pipe. When it is necessary to connect into a horizontal water pipe, make the connection to the top or side, rather than at the bottom, to avoid drawing off any sediment from the water pipe.

CHOOSE THE VALVE LOCATION

DRILL THE HOLE FOR THE VALVE

Drill a 1/4″ hole in the water pipe (even if using a self-piercing valve), using a sharp bit. Remove any burrs resulting from drilling the hole in the pipe.

Take care not to allow water to drain into the drill.

Failure to drill a 1/4″ hole may result in reduced ice production or smaller cubes.

Installation Instructions

Place the compression nut and ferrule (sleeve) for copper tubing onto the end of the tubing and connect it to the shutoff valve.

Make sure the tubing is fully inserted into the valve. Tighten the compression nut securely.

For plastic tubing from a GE SmartConnect

™

Refrigerator Tubing kit, insert the molded end of the tubing into the shutoff valve and tighten compression nut until it is hand tight, then tighten one additional turn with a wrench. Overtightening may cause leaks.

NOTE: Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.

CONNECT THE TUBING TO THE VALVE

Saddle-Type Shutoff Valve

Compression Nut

Packing Nut

Outlet Valve

Ferrule (sleeve)

Turn the main water supply on and flush out the tubing until the water is clear.

Shut the water off at the water valve after about one quart (1 liter) of water has been flushed through the tubing.

FLUSH OUT THE TUBING

SmartConnect

™

Tubing

Fasten the shutoff valve to the cold water pipe with the pipe clamp.

NOTE: Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.

FASTEN THE SHUTOFF VALVE

Tighten the clamp screws until the sealing washer begins to swell.

NOTE: Do not overtighten or you may crush the tubing.

TIGHTEN THE PIPE CLAMP

Pipe Clamp

Vertical Cold Water Pipe

Saddle-Type Shutoff Valve

Washer

Inlet End

Pipe Clamp

Clamp Screw

Route the tubing between the cold water line and the refrigerator.

Route the tubing through a hole drilled in the wall or floor (behind the refrigerator or adjacent base cabinet) as close to the wall as possible.

ROUTE THE TUBING

To complete the installation of the refrigerator, go back to Step 1 in Installing the Refrigerator.

INSTALLING THE WATER LINE (CONT.)

+ 90 hidden pages