4096-387
Revision E
April 20, 2016
ASSEMBLY MANUAL
1.2M Ku-BAND Rx/Tx
SERIES 1123
ANTENNA SYSTEM
General Dynamics SATCOM Technologies
1700 Cable Drive NE
Conover NC 28613 USA
Phone 770-689-2040
www.gdsatcom.com
1.2M Ku-BAND Rx/Tx
SERIES 1123
ANTENNA SYSTEM
E Add Conover Address 4/19/16 RAH
D Revised Company Name, Logo, and Part Tables 7/13/09 RAH
C Revised Address 1/11/02 RAH
B Revise per canister assembly 3/23/98 PGW
Revise and Update
A
- ORIGINAL RELEASE 9/22/94 R.FRYE
3/6/98 PGW
REV. DESCRIPTION DATE APPROVED
General Dynamics 4096-387
SATCOM Technologies 1.2M Ku-BAND Rx/Tx SERIES 1123
2
General Dynamics 4096-387
SATCOM Technologies 1.2M Ku-BAND Rx/Tx SERIES 1123
TABLE OF CONTENTS
SECTION TITLE
I INTRODUCTION
1.0 GENERAL INFORMATION
1.1 UNPACKING & INSPECTION
1.2 FREIGHT DAMAGE
1.3 MATERIAL MISSING OR DAMAGED
1.4 MECHANICAL INSTALLATION TOOLS
1.5 SITE SELECTION
1.6 FOUNDATION INTERFACE
II ANTENNA SYSTEM ASSEMBLY
2.0 REFLECTOR & SUPPORT ASM PART LIST
2.1 ANTENNA ASSEMBLY
III FEED SUPPORT ASSEMBLY
3.0 FEED SUPPORT PART LIST
3.1 FEED SUPPORT ASSEMBLY
IV SATELLITE ALIGNMENT
4.0 INITIAL POINTING
4.1 REPOINTING
V MAINTENANCE
5.0 MAINTENANCE OVERVIEW
5.1 REFLECTOR
5.2 MOUNT & REFLECTOR SUPPORT
5.3 FEED & FEED SUPPORT
3
General Dynamics 4096-387
SATCOM Technologies 1.2M Ku-BAND Rx/Tx SERIES 1123
SECTION I INTRODUCTION
1.0 GENERAL INFORMATION
This manual describes the assembly and installation of General Dynamics' 1.2
meter antenna system. The General Dynamics 1.2 meter is a rugged and reliable
mount which will operate in the Ku-Band frequency with high efficiency and at the
same time successfully withstand the effects of the environment.
These instructions are listed by sections that cover all areas of assembly and
installation. Additional sections are included in the manual to provide information
on antenna alignment to the satellite and maintenance.
1.1 UNPACKING AND INSPECTION
The system containers should be unpacked and inspected at the earliest date to
insure that all material has been received and is in good condition. A complete
packing list for each major component is supplied.
1.2 FREIGHT DAMAGE
Any damage to materials while in transit should be immediately directed to the
freight carrier. He will instruct you on matters regarding any freight damage
claims.
1.3 MATERIAL - MISSING OR DAMAGED
Any questions regarding missing or damaged materials that is not due to the
freight carrier should be directed to General Dynamics' Customer Service
Department at:
General Dynamics SATCOM Technologies
1700 Cable Drive NE
Conover NC 28613 USA
Phone 770-689-2040
www.gdsatcom.com
4
General Dynamics 4096-387
SATCOM Technologies 1.2M Ku-BAND Rx/Tx SERIES 1123
1.4 MECHANICAL INSTALLATION TOOLS
The following tools are suggested for the antenna installation.
HARDWARE SIZE
#10
1 / 4"
5/16"
3 / 8”
27/64" (Hilo)
1 / 2"
5 / 8”
SAE WRENCH
SIZE
FLATTEN
3 / 8”
7 /16" 11 mm
1 / 2" 13 mm
9 /16” 14 mm
1 / 2” 13 mm
3 / 4" 20 mm
15 / 16 “ 24 mm
METRIC WRENCH
SIZE
10 mm
MAXIMUM REC.
TORQUE
LOCK WASHERS
49 in-lbs.
12 ft-lbs.
15 ft-lbs.
Snug
35 ft-lbs.
70 ft-lbs.
NOTE: The Minimum Torque applied should not be less than 10% of maximum recommended tor que.
Also recommended for installation:
Inclinometer Compass
Adjustable Wrench Screw Driver (standard blade)
1.5 SITE SELECTION
In order to achieve maximum performance of your antenna system, it is important
to select the correct location for the antenna. The following guidelines should be
observed when selecting a site for the installation.
1. The line of site to the satellite should be clear of any obstructions, such as
trees or buildings.
2. The site should be relatively flat and level for ease of installation and
access to the antenna.
3. The site should be checked for underground obstruction, such as buried
cables or pipes.
4. All local building codes should be adhered to (i.e. grounding, foundation
requirements, zoning rules, setbacks, etc.).
5
General Dynamics 4096-387
A
SATCOM Technologies 1.2M Ku-BAND Rx/Tx SERIES 1123
1.6 FOUNDATION INTERFACE
The required interface from the foundation to the mount is 2-1/2" schedule 40
pipe (2.88" O.D.). A suggested in-ground foundation is shown in Figure 1.
30.0
12.0
2 1/2” SCH 40 PIPE
(2.88 O.D.)
SECTION A - A
A
30.0
SEE NOTE #7
45
NOTES:
1. 2 1/2” schedule 40 pipe should conform with ASTM A53.
2. All concrete should conform to building code standards and have a
minimum compressive strength of 3000 PSI at 28 days. (Per ACI-318-77)
3. Soil bearing capacity should be no less than 2000 PSF.
4. Concrete should be poured against undisturbed soil.
5. Allow concrete 24 hours set time before installation of antenna.
6. The antenna should be properly grounded to meet applicable local codes.
7. Minimum depth as shown or extend to local frost line.
8. Foundation meets the design requirements as set forth by the uniform building code.
(1982 edition)
(GENERAL DYNAMICS DOES NOT REPRESENT OR WARRANT THAT ANY PARTICULAR DESIGN
OR SIZE OF FOUNDATION IS APPROPRIATE FOR ANY LOCALITY OR EARTH STATION
INSTALLATION.)
Figure 1
6
General Dynamics 4096-387
SATCOM Technologies 1.2M Ku-BAND Rx/Tx SERIES 1123
SECTION II ANTENNA SYSTEM ASSEMBLY
REFLECTOR AND SUPPORT ASSEMBLY PART LIST- TABLE 2.0
ITEM PART NO.
1
2
3
4
5
6
7
0181-585 Canister Assembly 1
0181-399 Mount Assembly 1
VARIES 1.2M Reflector 1
0156-572 Elevation Marking Plate 1
0211-552 Elevation Indicator 1
8115-003 1/2” Coupling Nut 1
8104-007
1/2” Hex Nut
DESCRIPTION QTY
1
8
8302-006
#10 x .50 Screw
2
9
8302-004
#10 x .75 Screw
2
10
8201-037
#10 Flatwasher
6
11
8202-032
#10 Lockwasher
4
12
8111-005
#10 Hex Nut
2
13
8319-006
Hi-Lo Screw
4
7
General Dynamics 4096-387
SATCOM Technologies 1.2M Ku-BAND Rx/Tx SERIES 1123
2.1 ANTENNA ASSEMBLY
CAUTION: During the assembly procedure, the sequence of instructions must be
followed. Do not tighten any hardware until instructed.
Refer to the part list and referenced steps below.
STEP 1.
Remove the azimuth tube from the
mount assembly and set tube and
Mount Assembly
hardware aside.
Azimuth Tube
To Satellite (within 5 deg.)
STEP 2.
Rotation Bolt
A) Remove rotation bolt, washer and
lockwasher and set aside.
B) Place the canister assembly onto the
Canister
mast pipe.
C) Orient the canister assembly towards
the center of the satellite orbital arc
to within 5 degrees.
Canister Screws
D) Securely tighten the [6] canister
screws.
Mast
E) Tighten [6] lock nuts against canister.
8
General Dynamics 4096-387
A
SATCOM Technologies 1.2M Ku-BAND Rx/Tx SERIES 1123
STEP 3.
Azimuth Rod
A) Remove one 1/2” hex nut (item 7)
from the azimuth rod.
B) Slide azimuth tube ( from step 1 )
onto the azimuth rod.
½”
zimuth Tube
½”
Nut
C) Thread the previously removed 1/2”
nut (item 7) onto the azimuth rod to
hold the tube
in place.
Mount Assembly
STEP 4.
[ 7 ]
Thread a 1/2” hex nut (item 7) a distance
of 6” onto the elevation rod.
STEP 5.
Elevation Channel
A) Maneuver the mount assembly so
that the end of the elevation rod can
be inserted through the hole in the
elevation channel.
B) Thread the 1/2” coupling nut (item 6)
Elevation Rod
[ 6 ]
onto the elevation rod.
C) Snug all the hardware on the mount
assembly at this time.
9
General Dynamics 4096-387
SATCOM Technologies 1.2M Ku-BAND Rx/Tx SERIES 1123
STEP 6.
Mount Assembly
A) Place the 1.2M reflector face down on
a flat surface.
B) Place the mount onto the back of the
Feed
Support
Hole
Feed Rod
Hole
reflector and orient as shown.
C) Attach the mount assembly to the
reflector with [4] HiLo screws (item 13).
D) Tighten securely but DO NOT over
tighten as this may cause damage to
the reflector.
Feed Rod Hole
STEP 7.
A) Place the reflector mount assembly
(step 6) onto the canister assembly.
Holes for –20
deg. location
B) Secure the reflector mount assembly
to the canister with rotation bolt, washer
and lockwasher from Step 2.
C) When elevations below 20 degrees are
required, move the elevation bracket
and elevation rod to the lower set of
holes on the mount assembly angles.
Rotation Hardware
10
General Dynamics 4096-387
SATCOM Technologies 1.2M Ku-BAND Rx/Tx SERIES 1123
STEP 8.
[ 10, 12 ]
[ 9, 10, 11]
A) Attach elevation marking plate to the
mount assembly with #10 hardware
(items 9, 10, 11, 12).
B) Attach elevation indicator to the bottom
plate of the mount assembly with #10
hardware (items 8, 10, 11).
[ 8, 10, 11 ]
Elevation Marking Plate
Elevation Indicator
STEP 9.
Hardware
(step 1)
A) Adjust azimuth tube so that the tube
will fit into the hole in the bottom plate
of the mount assembly.
B) Secure tube to the mount assembly
with hardware set aside in Step 1.
C) Tighten all hardware at this time.
Azimuth Tube
11
General Dynamics 4096-387
SATCOM Technologies 1.2M Ku-BAND Rx/Tx SERIES 1123
SECTION III FEED SUPPORT ASSEMBLY
These Instructions are intended as a general reference for feed support assembly. If
your antenna system has specific feed support instructions, refer to them at this time.
CAUTION: During the assembly procedure, the sequence of instructions must be
followed. Do not tighten any hardware until instructed.
Refer to the part list and referenced steps below.
FEED SUPPORT PART LIST- TABLE 3.0
ITEM PART NO.
1
2
0176-213 Feed Rod 2
VARIES Feed Support 1
3
8319-004
8319-006
8308-019
DESCRIPTION QTY
11/32-14 x 7/8 Hi-Lo Screw
27/64-13 x 1-3/8 Hi-Lo Screw
M8 x 15 MM Screw
3
2
4
4
5/16” x 3.25 Bolt
8031-026
1
5/16” Flatwasher
2
5
8201-041
5/16” Lockwasher
1
6
8202-041
5/16” Hex Nut
1
7
8101-009
12
General Dynamics 4096-387
SATCOM Technologies 1.2M Ku-BAND Rx/Tx SERIES 1123
PART LIST - CONTINUED
ITEM PART NO.
8
8030-008
1/4 x 1.00 Bolt
DESCRIPTION QTY
2
9
8201-040
1/4” Flatwasher
4
10
8202-040
1/4” Lockwasher
2
11
8100-007
1/4” Hex Nut
2
3.1 FEED SUPPORT ASSEMBLY
STEP 1.
A) Attach feed rods to reflector
with 2 Hi-Lo screws (Item 3).
See Detail A
See Detail A.
Feed Rods
13
General Dynamics 4096-387
SATCOM Technologies 1.2M Ku-BAND Rx/Tx SERIES 1123
STEP 2.
A) Mount feed support tube between the
feed support brackets with [2] of
( items: 8, 9, 10, 11 ). See Detail B.
Feed Support Tube
See Detail B
STEP 3.
See Detail D
See Detail C
14
A) Connect the feed support tube to the
feed rods with 5/16” hardware
(items 4, 5, 6, 7). See Detail C.
B) Attach the feed support to the reflector
with Hi-Lo screw (item 3). See Detail D.
C) Tighten the hardware at the reflector
rim snug (details A & D ). Do Not over
tighten as this can cause damage to
the reflector.
D) Next tighten the 5/16” hardware and
then tighten the 1/4” hardware.
E) Attach the feed/ODE assembly to the
feed support.
General Dynamics 4096-387
SATCOM Technologies 1.2M Ku-BAND Rx/Tx SERIES 1123
DETAIL A
[ 3 ]
Reflector
Feed Rod
[ 9, 10, 11 ]
DETAIL B
Feed
Support
Brackets
Feed Support
DETAIL C
Feed Rods
[ 8 ]
[ 9, 10, 11 ]
[ 5 ]
[ 4 ]
Feed Support
Tube
Support
[ 5, 6, 7 ]
Feed
DETAIL D
Reflector
Bracket
Feed Support
[ 3 ]
15
General Dynamics 4096-387
SATCOM Technologies 1.2M Ku-BAND Rx/Tx SERIES 1123
SECTION IV ANTENNA POINTING
4.0 INITIAL POINTING
The 1.2 meter reflector contains a 22.6° elevation offset look angle. Therefore,
when the reflector aperture is perpendicular to the ground, the antenna is actually
looking 22.6° in elevation. Refer to Figure 2.
Step 1: Place an inclinometer on the reflector support angle as shown in Figure 2.
Step 2: Adjust the reflector up or down in elevation by turning the two ½" hex nuts
at the elevation channel until the desired elevation is read on the
(inclinometer reading plus 22.6° = elevation angle). Note: Be sure that the
elevation pivot hardware (5 places) is loose enough to allow adjustment
without damaging (bending) the elevation rod. Snug the hardware.
Step 3: Azimuth Adjustment: With the electronics set to acquire the satellite,
rotate the antenna in azimuth until the satellite is found. Snug the azimuth
adjustment hardware.
Step 4: Peak the antenna signal by fine adjustments made in both azimuth and
elevation until the optimum signal is achieved.
Step 5: Tighten all hardware used for adjustment.
Step 6: Scribe a line next to the Azimuth and Elevation indicators to mark the
satellite location as shown in Figure 3 and 4.
Step 7: If desired, locate a secondary satellite by repeating steps 1 through 5.
Mark this satellite location as described in step 6 and then return to the
primary satellite by returning azimuth and elevation to the first set of scribe
lines made.
16
General Dynamics 4096-387
r
t
A
t
SATCOM Technologies 1.2M Ku-BAND Rx/Tx SERIES 1123
4.1 REPOINTING
The quick repoint features of the antenna system make future repointing to
another satellite quick and easy to do with a minimum of tools and little or no
training.
Loosen the elevation hardware just enough to allow adjustment and raise or
lower the antenna until the elevation indicator aligns with the scribe line for the
secondary satellite. Tighten the hardware.
Loosen the azimuth hardware and rotate the antenna until the azimuth indicator
aligns with the scribe line for the secondary satellite. Tighten the bolt and the
repoint is complete.
Inclinomete
Elevation Adjustmen
zimuth Adjustmen
Figure 2
17
General Dynamics 4096-387
SATCOM Technologies 1.2M Ku-BAND Rx/Tx SERIES 1123
MARK AZIMUTH
SETTING HERE
Canister Plate
Figure 3
Elevation Marking Plate
MARK ELEVATION
SETTING HERE
Figure 4
18
General Dynamics 4096-387
SATCOM Technologies 1.2M Ku-BAND Rx/Tx SERIES 1123
SECTION V MAINTENANCE
5.0 MAINTENANCE OVERVIEW
After installation, the antenna requires only periodic inspection. It is anticipated
that maintenance, if required, will be minimal and easily handled by a local or inhouse maintenance staff.
5.1 REFLECTOR
General Dynamics' reflector does not require any maintenance. The composite
construction of the reflector is virtually impervious to any damages that could be
caused by weather or atmospheric conditions.
It is only necessary to inspect for any physical damage done by vandalism or
very severe weather conditions.
Should any damage be detected to a portion of the reflector, contact the
Customer Service Department at General Dynamics for recommendations
involving reflector repair.
5.2 MOUNT AND REFLECTOR SUPPORT STRUCTURE
The mount and reflector support structure supplied with this antenna is of st eel
construction and has a galvanized finish.
If there are any signs of structural failure, the mount members that are damaged
should be repaired or replaced.
CORROSION: Any corrosion on steel members may be repaired with a cold,
zinc-rich galvanizing paint.
5.3 FEED AND FEED SUPPORT
The feed support and feed rods should be inspected to insure that all hardware is
secure. The feed/radio mounting bolts should be tight.
The feed horn window should be inspected to insure that it is intact so that no
moisture can collect inside the feed horn.
19
Loading...