General XL1 Instruction Manual

INSTRUCTION MANUAL
XL1 Multi-line Laser
2
Please read this instruction manual before operating this product. Please store this instruction manual in the carry case for future reference.
CAUTION: Class 2 Laser Product
Do not stare directly into the laser beam from apertures. Do not disassemble the instrument or attempt to perform any internal servicing
as this will void your warranty. No user serviceable parts included.
Only approved and authorised service technicians can carry out warranty repairs.
SAFETY
3
Carry case
Laser glasses
Batteries
Laser target Tripod spacer
General XL1
Please ensure the following items are included with your laser. If anything is missing please contact your retailer.
ITEM CHECKLIST
INCHES
CM
1
1 2 3 4 5 6 7
2
3
4
Adjustable support legs
360° protractor base
Carry strap
Vertical laser ports (x2)
PRODUCT OVERVIEW
Horizontal laser ports (x1)
Control panel and bubble vial
Power / locking switch
5
CONTROL PANEL
Bubble vial
Horizontal lineVertical lines
Pulse mode
6
MODE
DETECTOR CONTROL PANEL*
Sound on / off
Laser sensor
Power indicator
Coarse / fine mode indicator
Coarse / fine mode
Bubble vial
*The detector is an additional accessory which can be purchased from your retailer.
On/off switch
Direction arrows
7
USING YOUR LASER
Setting Up
Power Supply
Operation
Select a place as close as practical to the work site. Ensure the location is clear of traffic.
Place the laser on a level surface such as a bench or mount. Level the unit by eye using the bubble vial as a guide.
The XL1 is powered by three AA alkaline batteries.
Once the unit is approximately level, turn the power switch to “on” position. Self levelling will commence and the horizontal beam will appear. If the unit is outside the self levelling range the unit will not level and the beam will flash repeatedly. Press the V and H button on the control panel to cycle through the active beams.
8
Using Your Detector*
Press the pulse button on the control panel on top of the laser to enter into pulse mode.
Switch the detector on and move it into the path of the laser beam.
Hold the detector upright for horizontal beams. Rotate the detector 90°
for vertical beams. The direction arrows will indicate the position of the laser beam. The centre LED will indicate alignment with the beam.
MODE
MODE
*The detector is an additional accessory which can be purchased from your retailer.
9
CARE AND MAINTENANCE
Reflective surfaces such as glass may reflect the beam, causing two beams to strike the detector at the same time. This may create inaccurate reference points.
This is a precision instrument and should always be transported within the carry case provided.
Always turn the on/off lock to “off” when transporting the unit.
Whenever possible, store the instrument in a dry, shady location.
The XL1 should be calibrated every 6 months, if ongoing
accurate levelling is required or an impact has occurred.
The operator should check the XL1 for accuracy before precision levelling is attempted.
Clean the instrument with a dry, soft cloth after use in dusty, damp or wet conditions before storing.
Smudges and fingerprints may be removed with a damp tissue or a soft, lint-free cloth.
10
WARRANTY
The General XL1 comes with a 3 year manufacturers warranty.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Separate to the above Australia Consumer Law, Spot-on oers a global warranty.
Customer Support
To assist you with any queries or technical questions please contact the customer support line: 1300 658 338
30 Day Free Service
If your laser is out of calibration within the rst 30 days of purchase you
are entitled to a free calibration adjustment. For more information please contact your retailer or Spot-on.
11
SPECIFICATIONS
Specications General XL1
Product code 70019
Warranty 3 Years
Accuracy ±2mm at 10m
Range 50m (detector)
Levelling range ±9% / ±5°
Laser class 2 Red
Battery life 10 hours
Battery type 3x AA
Vertical lines 2
Horizontal lines 1
IP rating 65
Weight (kg) 0.90
Dimensions (mm) 190x115x115
www.spoton.com.au
Loading...