1500PSI
The Reliable Ones
High Pressure Washer
Owner’s Manual
Problems?
Questions?
Before taking your unit
back to the store,
call the pressure washer
helpline at
1-800-270-1408
M-F 8-5 CST
This pressure
washer is
equipped with an
Automatic Cool
Down System.
See page 11 for
details
GENERAC
This symbol points out important safety instructions, which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all
instructions in the manual before attempting to operate this unit.
Model No. 10670 (1500 PSI High Pressure Washer) Manual No. B1915 Revision 0 (11/7/97)
2
High Pressure Washer
Generac 1500PSI High Pressure Washer
GENERAC
CAUTION: Always disconnect spark plug wire and place wire where it cannot contact spark
plug to prevent accidental starting when setting up, transporting, adjusting or making repairs
to your high pressure washer.
Engine exhaust gases contain DEADLY carbon monoxide gas.
This dangerous gas, if breathed in sufficient concentrations, can
cause unconsciousness or even death. Operate this equipment
only in the open air where adequate ventilation is available.
Gasoline is highly FLAMMABLE and its vapors are EXPLOSIVE.
Do not permit smoking, open flames, sparks or heat in the vicinity while handling gasoline. Avoid spilling gasoline on a hot engine.
Allow unit to cool for 2 minutes before refueling. Comply with all
laws regulating storage and handling of gasoline.
Locate this pressure washer in areas away from combustible
materials, combustible fumes or dust.
The high pressure equipment is designed to be used with Gen-
erac authorized parts only. If you use this equipment with parts
that do not comply with minimum specifications, the user assumes
all risks and liabilities.
Some chemicals or detergents may be harmful if inhaled or
ingested, causing severe nausea, fainting or poisoning. The harmful elements may cause property damage or severe injury.
Do not allow CHILDREN to operate the Pressure Washer at any
time.
Operate engine only at governed speed. Running the engine at
excessive speeds increases the hazard of personal injury. Do not
tamper with parts which may increase or decrease the governed
speed.
Do not wear loose clothing, jewelry or anything that may be
caught in the starter or other rotating parts.
Before starting the Pressure Washer in cold weather, check all
parts of the equipment and be sure ice has not formed there.
Units with broken or missing parts, or without protective housing
or covers should NEVER be operated.
The muffler and air cleaner must be installed and in good condi-
tion before operating the Pressure Washer. These components
act as spark arrestors if the engine backfires.
Check the fuel system for leaks or signs of deterioration such as
chafed or spongy hose, loose or missing clamps or damaged tank
or cap. Correct all defects before operating the Pressure Washer.
Do not spray flammable liquids.
Never aim the gun at people, animals or plants.
High pressure spray can cause paint chips or other particles to
become airborne and fly at high speeds.
Never allow any part of the body to come in contact with the fluid
stream. DO NOT come in contact with a fluid stream created by
a leak in the high pressure hose.
High pressure stream of water that this equipment produces can
pierce skin and its underlying tissues, leading to serious injury and
possible amputation.
Always wear eye protection when you use this equipment or
when you are in the vicinity where the equipment is in use.
Operate the pressure at no more than the PSI fluid pressure
rated for your pressure washer.
Never move the machine by pulling on the high pressure hose.
Use the handle provided on the top of the unit.
Always be certain the spray gun, nozzles and accessories are cor-
rectly attached.
Never use a spray gun which does not have a trigger lock or trig-
ger guard in place and in working order.
Use a respirator or mask whenever there is a chance that vapors
may be inhaled. Read all instructions with mask so you are certain the mask will provide the necessary protection against inhaling
harmful vapors.
High pressure spray may damage fragile items including glass.
Do not point spray gun at glass when in the jet spray mode.
Keep the hose connected to machine or the spray gun while the
system is pressurized. Disconnecting the hose while the unit is
pressurized is dangerous.
Hold the spray gun firmly in your hand before you start the unit.
Failure to do so could result in an injury from a whipping spray
gun. Do not leave the spray gun unattended while the machine
is running.
The cleaning area should have adequate slopes and drainage to
reduce the possibility of a fall due to slippery surfaces.
Keep water spray away from electric wiring or fatal electric shock
may result.
Do not secure trigger gun in the pull-back (open) position.
Do not by-pass any safety device on this machine.
The muffler and engine heat up during operation and remain hot
immediately after shutting it down. Avoid contact with a hot muf-
fler or engine or you could be severely burned.
Operate and store this unit on a stable surface.
High pressure hose can develop leaks from wear, kinking, abuse,
etc. Water spraying from a leak is capable of injecting material
into skin.Inspect hose each time before using it. Check all hoses
for cuts, leaks, abrasions or bulging of cover, or damage or move-
ment of couplings. If any of these conditions exist, replace hose
immediately. Never repair high pressure hose. Replace it with
another hose that meets minimum pressure rating of your pres-
sure washer.
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects, or other reproductive harm.
WWAARRNNIINNGG::
Generac 1500PSI High Pressure Washer
GENERAC
3
High Pressure Washer
CONGRATULATIONS on your purchase of a
GENERAC high pressure washer. It has been
designed, engineered and manufactured to give you
the best possible dependability and performance.
Should you experience any problem you cannot
easily remedy, please contact your nearest GENERAC Authorized Service facility, or call the 1-800
number listed on the front of this manual. We have
competent, well-trained technicians and the proper
tools to service or repair this unit.
Please read and retain this manual. The instructions
will enable you to assemble and maintain your high
pressure washer properly.
CUSTOMER
RESPONSIBILITIES
Read and observe the safety rules.
Follow regular schedule in maintaining, caring for
and using your high pressure washer.
Follow the instructions under Customer Responsi-
bilities and Storage sections of this Owner's
Manual.
PRODUCT SPECIFICATIONS
Pressure Washer Specifications
Outlet Pressure . . . . 1500 psi
Flow Rate . . . . . . . . . 2.0 gallons per minute (gpm)
Detergent Mix . . . . . . Use undiluted detergent
approved for pressure
washers
Water Supply . . . . . . Not to Exceed 140°F
Temperature
Automatic Cool . . . . Will cycle when water
Down System reaches 140°-145°F
Engine specifications
Engine Model . . . . . . Briggs & Stratton Sprint
Rated Horsepower . . 3.75
Displacement . . . . . . 148cc
Spark Plug
Type . . . . . . . . RJ19LM
Set Gap To: . . 0.030 inch (0.76mm)
Gasoline Capacity . . 1.0 U.S. quarts
Oil . . . . . . . . . . . . . . . SAE 30
In the State of California a spark arrestor is required
by law (Section 4442 of the California Public
Resources Code). Other states may have similar
laws. Federal laws apply on federal lands.
NOTE: If you equip the engine of your pressure
washer with a spark arrestor muffler, the spark
arrestor must be maintained in effective working order
by the owner/operator.
You can order a spark arrestor through your
authorized Generac service facility. See Engine Owners Manual for part number.
Model Number 1067-0
Serial Number
Date of Purchase
The model and serial numbers will be found on a
decal attached to the pressure washer. You could
record both serial number and date of purchase
and keep in a safe place for future reference.
4
High Pressure Washer
KNOW YOUR PRESSURE WASHER
Read this owners manual and safety rules before operating your high pressure washer.
Compare the illustrations with your high pressure washer to familiarize yourself with the locations of various
controls and adjustments. Save this manual for future reference.
Generac 1500PSI High Pressure Washer
GENERAC
Pump Develops high pressure.
Recoil Starter Used for starting the engine man-
ually.
Spray Gun Controls the application of water onto
cleaning surface with trigger device. Includes safety
latch.
Adjustable Nozzle Extension You must attach
this to the spray gun to provide high pressure
stream. Adjustable nozzle allows you to adjust spray
pattern.
Air Cleaner Dry type filter element limits the
amount of dirt and dust that gets in the engine.
High Pressure Outlet Connection for high pressure hose.
Water Inlet Connection for garden hose.
High Pressure Hose Connect one end to water
pump and the other end to spray wand.
Goggles Always use the enclosed goggles or
other eye protection when running your pressure
washer.
Foamer Used to apply detergent. Attaches to the
spray gun.
Primer Bulb Prepares a cold engine for starting.
Automatic Cool Down System Cycles water
through pump when water reaches 140°-145°F.
Warm water will discharge from pump onto
ground. This system prevents internal pump
damage.
Spray Gun
Adjustable Nozzle Extension
High Pressure Hose
Goggles
Air Cleaner
Primer Bulb
Gas Cap
High Pressure Outlet
Recoil Starter
Foamer
Water Inlet
Oil Fill Cap
Pump equipped with
Automatic Cool Down System
High Pressure Washer
5
Read entire Owners manual before you attempt to
assemble or operate your new pressure washer.
Your new pressure washer has been assembled at
the
factory with the exception of those parts left unassembled for shipping purposes.
REMOVE PRESSURE
WASHER FROM CARTON
Remove parts box included with pressure washer.
Slice two corners at guide handle end of carton
from top to bottom so the panel can be folded down
flat, then remove all packing material.
Roll pressure washer out of carton.
CARTON CONTENTS
Items in the carton include:
Main Unit
Parts Box (which includes the following):
Wireform
Goggles
Nozzle Cleaning Kit
Owners Manual
Engine Manual
Spray Gun
Nozzle Extension
Spray Head
High Pressure Hose
Handle
Foamer Bottle
Parts Bag (which includes the following):
2 carriage bolt
2 knobs
If any of the above parts are missing or damaged, call
the pressure washer helpline at 18002701408.
PREPARING THE PRESSURE
WASHER FOR USE
If you have any problems with the assembly of your
pressure washer or if parts are missing or damaged,
call the Pressure Washer Helpline at 1-800-270-1408.
To prepare your pressure washer for operation you
will need to perform these tasks:
Attach the handle and attach the wire form that
holds high pressure hose and spray gun.
Add oil to engine crankcase.
Add fuel to fuel tank.
Connect high pressure hose to the spray gun and
the pump and connect water supply to the pump.
Attach the Handle
Place the top of the handle onto the bottom of the
handle already connected to the main unit making
sure the holes in the top align with the holes on the
bottom (Figure 1).
Generac 1500PSI High Pressure Washer
AA
SSSSEEMMBBLL
YY
GENERAC
Figure 1 — Attach the top of the handle to the
bottom of the handle.
Make sure the
holes on the
top of the
handle are
aligned with the
holes in the
bottom of the
handle
Generac 1500PSI High Pressure Washer
AASSSSEEMMBBLLYY
GENERAC
6
High Pressure Washer
Insert the carriage bolts through the holes (looking
at the back of the pressure washer) as shown in
Figure 2 and attach the plastic knobs. Tighten the
knob by hand (Figure 2).
Fit wire form on guide handle (Figure 3).
This view is from the back of the pressure washer.
Add Engine Oil
IMPORTANT: Any attempt to crank or start the
engine before it has been properly serviced with the
recommended oil may result in an engine failure.
Note: When adding oil to the engine crankcase, use
only high quality detergent oil rated with API service
classification SF,SG, SH or SH/CD rated SAE 30
weight. Select the oils viscosity grade according to
your expected operating temperature. Do Not Use
SAE 10W40 Oil.
Although multi-viscosity oils (5W30, 10W30, etc.)
improve starting in cold weather, these multi-viscosity
oils will result in increased oil consumption when used
above 32°F. Check your engine oil level more frequently to avoid possible damage from running low on
oil.
Place pressure washer on a level surface.
Clean area around oil fill and remove oil dipstick
(Figure 4)
Wipe dipstick clean. Pour oil into oil fill opening until
oil reaches FULL mark on the dipstick. Stop occasionally to check oil level. DO NOT OVERFILL.
Install oil dipstick, hand tighten securely.
Note: Check Oil Often During Engine Breakin.
Add Gasoline
DANGER! Never fill fuel tank indoors.
Never fill fuel tank when engine is running or hot. Do not smoke when filling
fuel tank.
WARNING! Never fill fuel tank completely
full. Fill tank to about 1/2" below the
bottom of the filler neck to provide space
for fuel expansion. Wipe away any fuel
spillage from engine and equipment
before starting.
The manufacturer recommends fresh, clean unleaded
regular automotive gasoline.
Figure 3 — Fit wire form on handle.
Figure 4 — Add oil to engine crankcase. Do not
attempt to start engine without
adding oil.
Oil Fill Cap
colder 32°F warmer
5W30 SAE 30
Figure 2 — Insert the carriage bolts and attach
the knobs.
Loading...