Generac Power Systems 004700-00 User Manual

Download

Owner’s Manual and

Installation Instructions

Air-cooled Recreational

Vehicle Generators

• Model: 004700-0 QUIETPACT 40G

This manual should remain with the unit.

INTRODUCTION

Thank you for purchasing this model of the QUIETPACT product line by Generac Power Systems Inc. This model is designed and manufactured to supply electrical power for recreational vehicles.

READ THIS MANUAL THOROUGHLY



If any portion of this manual is not understood, contact the nearest Authorized Service Dealer for starting, operating and servicing procedures.

Throughout this publication, and on tags and decals affixed to the generator, DANGER, WARNING, CAUTION and NOTE blocks are used to alert personnel to special instructions about a particular operation that may be hazardous if performed incorrectly or carelessly. Observe them carefully. Their definitions are as follows:

DANGER

After this heading, read instructions that, if not

strictly complied with, will result in personal injury or property damage.

After this heading, ead instructions that, if not

strictly complied with, may result in personal injury or property damage.

After this heading, read instructions that, if not

strictly complied with, could result in damage to equipment and/or property.

NOTE:

After this heading, read explanatory statements

that require special emphasis.

These safety warnings cannot eliminate the hazards that they indicate. Common sense and strict compliance with the special instructions while performing the service are essential to preventing accidents.

Four commonly used safety symbols accompany the DANGER, WARNING and CAUTION blocks. The type of information each indicates follows:

 This symbol points out important safety informa-



tion that, if not followed, could endanger personal safety and/or property of others.

This symbol points out potential explosion hazard.



This symbol points out potential fire hazard.



This symbol points out potential electrical shock



hazard.

The operator (driver) is responsible for proper and safe use of the vehicle and its equipment, and the safety of all vehicle occupants. We strongly recommend that the operator read this manual and thoroughly understand all instructions before using this equipment. We also strongly recommend instructing other occupants in the vehicle to properly start and operate the generator. This prepares them if they need to operate the equipment in an emergency.

CONTENTS



This manual contains pertinent owner’s information, including warranty, electrical diagrams, exploded views and lists of repair parts for generator model numbers 004700-0. In addition, the latter portion of this manual contains information necessary for the proper installation of these generators.

OPERATION AND MAINTENANCE



It is the operator's responsibility to perform all safety checks, to make sure that all maintenance for safe operation is performed promptly, and to have the equipment checked periodically by an Authorized Service Dealer. Normal maintenance service and replacement of parts are the responsibility of the owner/operator and, as such, are not considered defects in materials or workmanship within the terms of the warranty. Individual operating habits and usage contribute to the need for maintenance service.

Proper maintenance and care of the generator ensures a minimum number of problems and keep operating expenses at a minimum. See an Authorized Service Dealer for service aids and accessories.

HOW TO OBTAIN SERVICE



When the generator requires servicing or repairs, simply contact an Authorized Service Dealer for assistance. Service technicians are factory-trained and are capable of handling all service needs.

When contacting an Authorized Service Dealer or the factory about parts and service, always supply the complete model number and serial number of the unit as given on its data label, which is located on the generator.

Model No. ____________ Serial No. ______________

AUTHORIZED SERVICE

DEALER LOCATION

To locate the nearest AUTHORIZED SERVICE

DEALER, please call this number:

1-800-333-1322

or locate us on the web at:

www.generac.com

Table of Contents

Recreational Vehicle Generator

Part I – Owner’s Manual

Introduction ...................................... Inside Front Cover

Read This Manual Thoroughly ................................ IFC

Contents .................................................................IFC

Operation and Maintenance ....................................IFC

How to Obtain Service ............................................ IFC

Authorized Service Dealer Locator Number .............. IFC

Safety Rules ...................................................................... 2

Section 1 – General Information ................................. 4

1.1 Generator Identification ...................................... 4

1.2 Generator Applicability ....................................... 5

1.3 Safety..... .............................................................. 5

1.4 Generator AC Connection System ....................... 5

1.5 Specifications ...................................................... 5

Section 2 – Operation .................................................... 7

2.1 Generator Control Panel ....................................... 7

2.2 Optional Remote Start/Stop Panel ........................ 7

2.3 Automatic Choke .................................................. 7

2.4 Before Starting the Engine ................................... 7

2.5 Starting the Generator ......................................... 8

2.6 Stopping the Generator ........................................ 9

2.7 Applying Loads to Generator ................................ 9

2.8 Do Not Overload the Generator ............................ 9

2.9 Protection Systems ............................................... 9

2.10 Additional Information ....................................... 10

Section 3 – Maintenance .............................................. 11

3.1 Checking the Engine Oil Level ............................ 11

3.2 Changing the Engine Oil and/or Oil Filter .......... 11

3.3 Maintaining the Engine Air Cleaner .................... 12

3.4 Clean Air Intake ................................................. 13

3.5 Checking the Engine Spark Plug ........................ 13

3.6 Fuel Filter ........................................................... 13

3.7 Spark Arrestor Service ....................................... 13

3.8 Cleaning the Generator ...................................... 14

3.9 Battery Maintenance ........................................... 14

3.10 Major Service Manual ......................................... 15

3.11 Exercising the Generator .................................... 15

3.12 Out of Service Procedure .................................... 15

3.13 Adjusting Valve Clearance................................... 15

3.14 RV Generator Service Interval ............................ 16

Part II – Installation Instructions

Safety Rules .................................................................... 18

Section 1 – General Information ............................... 20

1.1 Purpose and Scope of the Manual ..................... 20

1.2 Safety...... ........................................................... 20

1.3 Standards Booklets ........................................... 20

1.4 Equipment Description ..................................... 20

1.5 Generator Engine Operating Speed ................... 20

1.6 Generator AC Connection System ..................... 20

Section 2 – Installation ................................................ 22

2.1 Location and Support ....................................... 22

2.2 Generator Compartments ................................. 23

2.3 Cooling and Ventilating Air ................................ 26

2.4 Gasoline Fuel System ........................................ 26

2.5 Exhaust System................................................. 27

2.6 Electrical Connections ....................................... 28

2.7 Battery Installation... ......................................... 31

2.8 Optional Accessories ......................................... 31

Section 3 – Post-installation Start-up

Adjustments .............................................. 32

3.1 Post Installation Tests ....................................... 32

3.2 Before Initial Start-up ........................................ 32

3.3 Initial Start ........................................................ 32

3.4 Testing Under Load ........................................... 32

3.5 Installation Checklist ......................................... 33

Appendix 1 – Notes ...................................................... 34

Appendix 2 – Troubleshooting ................................... 35

Appendix 3 – Electrical Data ...................................... 36

Appendix 4 – Exploded Views and Parts Lists ....... 38

Appendix 5 – Warranty ................................................ 48

Safety Rules

Recreational Vehicle Generator

SAVE THESE INSTRUCTIONS – The manufacturer suggests that these rules for safe

operation be copied and posted in potential hazard areas of the recreational vehicle.



Safety should be stressed to all operators and potential operators of this equipment.

• The generator engine releases DEADLY carbon



The engine exhaust from this product

contains chemicals known to the state

defects or other reproductive harm.



This product contains or emits chemicals known to the state of California to cause

cancer, birth defects or other reproductive harm.

Study these SAFETY RULES carefully before installing, operating or servicing this equipment. Become familiar with this manual and with the unit. The generator can operate safely, efficiently and reliably only if it is properly installed, operated and maintained. Many accidents are caused by failing to follow simple and fundamental rules or precautions.

The manufacturer cannot anticipate every possible circumstance that might involve a hazard. The warnings in this manual, and on tags and decals affixed to the unit, are, therefore, not all-inclusive. If using a procedure, work method or operating technique the manufacturer does not specifically recommend, ensure that it is safe for others. Also make sure the procedure, work method or operating technique utilized does not render the generator unsafe.

WARNING:

of California to cause cancer, birth

WARNING:

DANGER

Despite the safe design of this generator,



operating this equipment imprudently, neglecting its maintenance or being careless can cause possible injury or death. Permit only responsible and capable persons to operate or maintain this equipment.

Potentially lethal voltages are generated by



these machines. Ensure all steps are taken to render the machine safe before attempting to work on the generator.

Parts of the generator are rotating and/or hot



during operation. Exercise care near running generators.

GENERAL HAZARDS



• For safety reasons, the manufacturer recommends that the installation, initial start-up and maintenance of this equipment is carried out by an Authorized Service Dealer.



monoxide gas through its exhaust system. This dangerous gas, if breathed in sufficient concentrations, can cause unconsciousness or even death. Never operate the generator set with the vehicle inside any garage or other enclosed area. DO NOT OPERATE THE GENERATOR IF THE EXHAUST SYSTEM IS LEAKING OR HAS BEEN DAMAGED. SYMPTOMS OF CARBON MONOXIDE POISONING ARE (a) inability to think coherently, (b) nausea, (c) vomiting, (d) twitching muscles, (e) throbbing temples, (f) dizziness, (g) headaches, (h) weakness, and (i) sleepiness. IF EXPERIENCING ANY OF THESE SYMPTOMS, MOVE INTO FRESH AIR IMMEDIATELY. IF SYMPTOMS PERSIST, GET MEDICAL HELP. Shut down the generator and do not operate it until it has been inspected and repaired.

• Never sleep in the vehicle while the genset is running unless the vehicle has a working carbon monoxide detector. The exhaust system must be installed in accordance with the genset installation manual. Make sure there is ample fresh air when operating the genset in a confined area.

• The engine exhaust fumes contain carbon monoxide, which can be DEADLY. This dangerous gas, if breathed in sufficient concentrations, can cause unconsciousness or even death. This exhaust system must be installed properly, in strict compliance with applicable codes and standards. Following installation, do nothing that might render the system unsafe or in noncompliance with such codes and standards. The generator compartment must be completely vapor sealed from the vehicle interior. There must be no possibility of exhaust fumes entering the vehicle interior. Never operate this equipment with a leaking or defective exhaust system.

• Keep hands, feet, clothing, etc., away from drive belts, fans, and other moving or hot parts. Never remove any drive belt or fan guard while the unit is operating.

• Adequate, unobstructed flow of cooling and ventilating air is critical to correct generator operation and is required to expel toxic fumes and fuel vapors from the generator compartment. Without sufficient cooling airflow, the engine/generator quickly overheats, which causes serious damage to the generator. Do not alter the installation or permit even partial blockage of ventilation provisions, as this can seriously affect safe operation of the generator.



• When working on this equipment, remain alert at all times. Never work on the equipment when physically or mentally fatigued.

• Inspect the generator regularly, and contact the nearest Authorized Service Dealer immediately for parts needing repair or replacement.

• Before performing any maintenance on the generator, disconnect its battery cables to prevent accidental start up. Disconnect the cable from the battery post indicated by a NEGATIVE, NEG or (–) first. Reconnect that cable last.

• Never use the generator or any of its parts as a step. Stepping on the unit can stress and break parts, and may result in dangerous operating conditions from leaking exhaust gases, fuel leakage, oil leakage, etc.

ELECTRICAL HAZARDS



• The generator covered by this manual produces dangerous electrical voltages and can cause fatal electrical shock. Avoid contact with bare wires, terminals, connections, etc., while the unit is running. Ensure all appropriate covers, guards and barriers are in place before operating the generator. If work must be done around an operating unit, stand on an insulated, dry surface to reduce shock hazard.

• Do not handle any kind of electrical device while standing in water, while barefoot, or while hands or feet are wet. DANGEROUS ELECTRICAL SHOCK MAY RESULT.

• During installation onto the vehicle, have the generator properly grounded (bonded) either by solid mounting to the vehicle frame or chassis, or by means of an approved bonding conductor. DO NOT disconnect the bonding conductor, if so equipped. DO NOT reconnect the bonding conductor to any generator part that might be removed or disassembled during routine maintenance. If the grounding conductor must be replaced, use only a flexible conductor that is of No. 8 American Wire Gauge (AWG) copper wire minimum.

• In case of accident caused by electric shock, immediately shut down the source of electrical power. If this is not possible, attempt to free the victim from the live conductor. AVOID DIRECT CONTACT WITH THE VICTIM. Use a nonconducting implement, such as a rope or board, to free the victim from the live conductor. If the victim is unconscious, apply first aid and get immediate medical help.

• Never wear jewelry when working on this equipment. Jewelry can conduct electricity resulting in electric shock, or may get caught in moving components causing injury.



Safety Rules

Recreational Vehicle Generator

FIRE HAZARDS



• For fire safety, the generator must be installed and maintained properly. Installation always must comply with applicable codes, standards, laws and regulations. Adhere strictly to local, state and national electrical and building codes. Comply with regulations the Occupational Safety and Health Administration (OSHA) has established. Also, ensure that the generator is installed in accordance with the manufacturer’s instructions and recommendations. Following proper installation, do nothing that might alter a safe installation and render the unit in noncompliance with the aforementioned codes, standards, laws and regulations.

• Keep a fire extinguisher in the vehicle at all times. Extinguishers rated “ABC” by the National Fire Protection Association are appropriate for use on the recreational vehicle generator electrical system. Keep the extinguisher properly charged and be familiar with its use. If there are any questions pertaining to fire extinguishers, consult the local fire department.

EXPLOSION HAZARDS



• Do not smoke around the generator. Wipe up any fuel or oil spills immediately. Ensure that no combustible materials are left in the generator compartment, or on or near the generator, as FIRE or EXPLOSION may result. Keep the area surrounding the generator clean and free from debris.

• Gasoline is extremely FLAMMABLE and its vapors are EXPLOSIVE. Do not permit smoking, open flame, sparks or any source of heat in the vicinity while handling gasoline. Comply with all laws governing the storage and handling of gasoline.





Section 1 – General Information

RAC OHVI INDUSTRIAL ENGINE

RV SERVICE LOCATOR:

1.800.333.1322

SERVICE ACCESS PAN EL

OIL LEVEL: CHECK DAILY

AIR FILTER: CLEAN PREFILTER

EVERY 100 HOURS. REPLACE ELEMENT EVERY 250 HOURS.

OIL & OIL FILTER:

CHANGE EVERY 100

(IF NECESSARY)

EVERY 500 HOURS.

HOURS. REPLACE PLUGS

PLUGS EVERY 100

INSPECT & CLEANSPARK PLUGS:

REPLACEMENT INFORMATION

PERFORM MORE OFTEN IN DUSTY CONDITIONS

AIR FILTER LOCATED BEHIND PANEL.

MAINTENANCE SCHEDULE

AIR FILTER P/N: 0D3262

070185OIL FILTER P/N:

SPARK PLUG P/N: 072347

OIL CAPACITY WITH FILTER:

0.8L/0.84QT

TEMPERATURE SAE VISCOSITY

32˚F AND HIGHER

10˚F TO 100˚F

0˚F TO 80˚F

-20˚F TO 50˚F 5W-30

10W-30

15W-40

WHEN SERVICE OR PARTS ARE NEEDED IN

THE USA OR CANADA, CONTACT THE GENERAC

SERVICE LOCATOR AT 1-800-333-1322.

HOURS. (OR ANNUALLY)

PREFILTER P/N: 0D4511

FUEL FILTER P/N: 0D7515

FUEL FILTER: CHANGE EVERY 400

HOURS. (OR ANNUALLY)

PRIME

FUEL

STOP

START

30A

C.B.

15A

FUSE

CONTROL CENTER

10/15

14,16

9/11

Recreational Vehicle Generator

1.1 GENERATOR IDENTIFICATION

Please record the following information from the generator DATA DECAL or information decal.

1. Model Number _____________________ 2. Serial Number __________________

3. kW Rating _________________________ 4. Rated Voltage __________________

Model: 004700-0

1. Generator Air Intake

2. Engine Start/Stop Switch

3. Fuse

4. Optional Remote Panel Receptacle (Side View)

5. Generator AC Output Leads (Side View)

6. Fuel Primer Switch

7. Circuit Breaker

8. Starter Contactor

9. Fuel Inlet

10. Fuel Pump (Behind Access Panel)

11. Fuel Filter (Side View)

12. Oil Filter

13. Oil Drain Cap

14. Oil Dipstick

15. Air Filter (Behind Access Panel)

16. Oil Fill

17. Spark Plug

Section 1 – General Information

Recreational Vehicle Generator

1.2 GENERATOR APPLICABILITY

These generators have been designed and manufactured for supplying electrical power for recreational vehicles. Do not modify the generator or use it for any application other than for what it was designed. If there are any questions pertaining to its application, contact an Authorized Service Dealer. Do not use the unit until advised by a competent authority.

For fire safety, the generator must have been



properly installed in compliance with ANSI

119.2-1975/NFPA 501C-1974, “Standard for Recreational Vehicles, Part III – Installation of Electrical Systems.” The generator also must have been installed in strict compliance with the manufacturer’s detailed installation instructions. After installation, do nothing that might render the unit in noncompliance with such codes, standards and instructions.

Use this generator to supply electrical power for operating 120-volt, single-phase, 60 Hertz, AC electrical loads. These loads can require up to 3,600 watts (3.6 kW) of power, but cannot exceed 30 AC amperes of current at 120 volts.

DANGER

1.4 GENERATOR AC

CONNECTION SYSTEM

This generator set is equipped with dual stator AC power windings. These two-stator windings supply electrical power to customer electrical loads by means of a two-wire connection system. Note, however, that the neutral is bonded to the frame of the engine-generator.

The generator may have been installed so that it powers 120-volt AC loads (Figure 1.1). It can be wired to connect 120-volt AC electrical loads. This procedure should be done by an Authorized Service Dealer or other qualified installer.

Figure 1.1 – Connections for 120 Volts Only

Do not overload the generator. Some installa-



tions may require that electrical loads be alternated to avoid overloading. Applying excessively high electrical loads may damage the generator and may shorten its life. Add up the rated watts of all electrical lighting, appliance, tool and motor loads the generator will power at one time. This total should not be greater than the wattage capacity of the generator. If an electrical device nameplate gives only volts and amps, multiply volts times amps to obtain watts (volts x amps = watts). Some electric motors require more watts of power (or amps of current) for starting than for continuous operation.

1.3 SAFETY

Before attempting to use the generator set, carefully read the “Safety Rules” section of this manual. Comply strictly with these rules to prevent accidents and damage to equipment and/or property. We suggest copying and posting the “Safety Rules” in potential hazard areas of the vehicle. Stress safety to all operators and potential operators of this equipment.

1.5 SPECIFICATIONS

1.5.1 FUEL REQUIREMENTS



This generator is equipped with a gasoline fuel system. Depending on the installation, the generator may have either a separate fuel tank, or it may “share” the vehicle engine’s fuel tank.

NOTE:

Some installations using a “shared” fuel tank may have a generator fuel pickup tube that is shorter than the vehicle engine’s pickup tube. Such an arrangement causes the generator engine to “run out of gas” while adequate fuel for the vehicle remains in the tank.

To reduce lead and carbon deposits use high quality UNLEADED gasoline with the generator. Leaded REGULAR grade gasoline is an acceptable substitute.

NOTE:

Using unleaded gasoline contributes to longer engine valve life by reducing lead and carbon deposits.

Section 1 – General Information

Recreational Vehicle Generator

The manufacturer does not recommend using



any gasoline containing alcohol (such as “gasohol”). If using any gasoline containing alcohol, it must not contain more than 10 percent ethanol, and it must be removed from the generator during storage. Do NOT use any gasoline containing methanol. If using gasoline with alcohol, inspect more frequently for fuel leaks and other abnormalities.

1.5.2 FUEL CONSUMPTION



Model No Load 1/2 Load Full Load

004700-0 0.24 0.35 0.55

Fuel consumption is in gal/hr.



1.5.3 ENGINE OIL REQUIREMENTS

Use only high quality detergent oil rated with American Petroleum Institute (API) Service Classification SF, SG or SH. The recommended oil weights include the following:

• During summer months: SAE 30. An acceptable substitute is SAE 10W-30.

• During winter months: SAE 5W-30. DO NOT USE SAE 10-W40.

Crankcase and oil filter capacity is approximately 800 mL or .84 U.S. quarts. Do NOT use special additives. See Sections 3.1 and 3.2 for oil level check and fill procedures.

1.5.5 GENERATOR



Rated Maximum Continuous

AC Output (Gasoline) ...........................3,600 Watts (3.6 kW)

Rated Voltage ....................................................... 120 Volts AC

Rated Maximum Continuous

AC Current (Gasoline) ....................................... 30 Amperes

Phase .............................................................................. Single

Rotor RPM .......................................................................3,600

Number of Rotor Poles...........................................................2

Engine RPM .....................................................................3,600

Rated AC Frequency ....................................................... 60 Hz

Battery Charge Voltage .......................................... 14 Volts DC

Battery Charge Current ................................ 2 Amperes (max)

Gasoline weight .....................................................170 Pounds

Length .................................................... 749.8 mm (29.52 in.)

Width ..................................................... 483.1 mm (19.02 in.)

Height .................................................... 342.2 mm (13.47 in.)

1.5.6 EMISSIONS COMPLIANCE PERIOD



For non-handheld engines the Emissions Compliance Period referred to on the Emissions Compliance Label indicates the number of operating hours for which the engine has been shown to meet Federal emission requirements.

• For engines less than 225 cc displacement, Category C=125 hours, B=250 hours, and A=500 hours.

• For engines of 225 cc or more, Category C=250 hours, B=500 hours, and A=1000 hours.

1.5.4 ENGINE



Type of Engine ................................... GN-220, Single-cylinder

Cooling Method ........................................................Air-cooled

Rated Horsepower .......................................7.8 @ 4,200 rpm

Displacement .................................................................. 220cc

Cylinder Block ......................... Aluminum w/Cast Iron Sleeve

Type of Governor ............................. Mechanical, Fixed Speed

Air Cleaner ........................ Paper Element w/Foam Precleaner

Starter ....................................................... 12-volt DC Electric

Ignition System ..................... Solid-state w/Flywheel Magneto

Recommended Spark Plug

Champion ................................................................ RC14YC

AC .................................................................................. R45S

Fram Autolite .....................................................................65

Spark Plug Gap ....................................... 0.030 inch (76 mm)

Recommended Minimum Battery .............. 400 Cold-cranking

Amperes

Section 2 – Operation

Recreational Vehicle Generator

2.1 GENERATOR CONTROL PANEL

The following features are mounted on the generator control panel (Figure 2.1):

Figure 2.1 – Generator Control Panel

CONTROL CENTER

START

STOP

2.1.1 FUEL PRIMER



Before starting a cold engine (if it has not been started in more than two weeks), press this switch for approximately 10 to 15 seconds to bring fuel from the tank to the carburetor. This rocker type switch springs back into its original position when released.

2.1.2 START/STOP SWITCH



To crank and start the engine, hold this switch in the START position. Release the switch when the engine starts. To stop an operating engine, press and hold the switch in the STOP position until the engine shuts off. The switch center position is the RUN position.



2.1.3 FUSE

The fuse protects the engine’s DC control circuit against electrical overload. If the fuse element has melted open due to overloading, the engine cannot be cranked. If the fuse must be replaced, use only an identical replacement.

2.1.4 MAIN BREAKER



The main breaker protects the generator’s AC output circuit against overload and provides a method of turning OFF the generator’s 120-volt AC output to the vehicle circuits. This generator has 30-amp breaker.

FUEL

PRIME

FUSE

7. 5 A

C.B.

30A

2.2 OPTIONAL REMOTE

START/STOP PANEL

A remote mounted Start/Stop Panel is available that allows starting and stopping the generator engine conveniently from inside the vehicle.

Order part number 0F0429 or 0F0430, a remote panel that includes a Start/Stop switch, a generator run lamp, a fuel prime switch, and an hourmeter. The hourmeter provides a continuous indication of engine/generator operating time. Use the hourmeter for checking off periodic maintenance requirements on the unit.

2.3 AUTOMATIC CHOKE

The engine is equipped with an automatic choke that consists of two main components: a choke solenoid and prechoke.

2.3.1 CHOKE SOLENOID



During engine cranking (Start/Stop switch at START), a solid-state choke module signals the choke solenoid to activate and cycle (choke on/choke off) until the engine starts. The choke solenoid thus opens and closes the carburetor choke valve only when the engine is cranking. When the engine starts, the choke stops cycling.

2.3.2 PRECHOKE



The choke system also has a temperature-sensitive metal strip that adjusts choke valve angle according to ambient temperatures (i.e., in cold ambient temperatures, choke valve closes more). Once the engine starts, an element heats the temperature-sensitive strip to a normal operating condition, opening the choke valve. This may take about three minutes in cooler weather.

2.4 BEFORE STARTING THE ENGINE

NOTE:

Instructions and information in this manual assume the generator has been properly installed, connected, serviced, tested and adjusted by a qualified installation technician or installation contractor.



2.4.1 INSTALLATION

Generator installation must have been properly completed so it complies with all applicable codes, standards and regulations and with the manufacturer's recommendations.

Section 2 – Operation

Recreational Vehicle Generator

2.4.2 ENGINE LUBRICATION



Have the engine crankcase properly serviced with the recommended oil before starting. Refer to Section

1.5.4, and Sections 3.1 and 3.2 for oil servicing procedures and recommendations.

Any attempt to crank or start the engine before



it has been properly serviced with the recommended oil may result in an engine failure.

2.4.3 FUEL SUPPLY



The engine must have an adequate supply of proper fuel to operate. Before starting it, check that sufficient fuel is available.

NOTE:

Depending on the installation, the generator may have either a separate fuel tank, or it may “share” the vehicle engine’s fuel tank.

2.4.4 COOLING AND VENTILATING AIR



Air inlet and outlet openings in the generator compartment must be open and unobstructed for continued proper operation. Without sufficient cooling and ventilating airflow, the engine/generator quickly overheats, which causes it to shut down and may damage the generator.

2.4.5 ENGINE EXHAUST GAS



Before starting the generator engine, be sure there is no way for exhaust gases to enter the vehicle interior and endanger people or animals. Close windows, doors and other openings in the vehicle that, if open, might permit exhaust gases to enter the vehicle.

DANGER

The generator engine releases DEADLY carbon



DANGER

Never sleep in the vehicle while the genset is



running unless the vehicle has a working carbon monoxide detector. The exhaust system must be installed in accordance with the genset installation manual. Make sure there is ample fresh air when operating the genset in a confined area.

2.5 STARTING THE GENERATOR

NOTE:

Read the vehicle manufacturer’s instructions. The owner/operator should become familiar with the vehicle in which this generator is installed. Differences exist between vehicles. For example, some vehicles may use a transfer switch to isolate dockside power from the generator, while other vehicles may use an isolating receptacle. Some vehicles may be equipped with a DC converter, which allows the generator to power certain DC lighting and other DC loads.

To start the generator from either the generator control panel or from the optional remote panel, proceed as follows:

1. Turn OFF electrical loads using the means pro-

vided in the vehicle (such as a main line circuit breaker or transfer switch).

NOTE:

If starting from the generator control panel, turn OFF loads by setting the generator’s main circuit breaker to the OFF (or open) position. If starting from a remote panel, turn OFF loads using the means provided in the vehicle (such as a main circuit breaker). Electrical load circuits will be turned ON after the generator has started, stabilized and warmed up.

2. If the engine has not been started in more than

two weeks, press the Fuel Pump Primer switch and hold it for about 10 to 15 seconds to prime the fuel system. However, if the engine is warm, skip Step 2.

3. Hold the engine Start/Stop switch in the START

position to crank the engine. Release the switch when the engine starts.

If the engine does not start after it has been



cranking for 15 seconds, release the Start/Stop switch, wait one minute and try again. Holding the switch for longer than 15 seconds can damage the starter motor.

4. Let the engine run at no-load for a few minutes to

stabilize and warm up.

5. Turn ON electrical loads using the means pro-

vided (such as a main circuit breaker or transfer switch).

Section 2 – Operation

Recreational Vehicle Generator

2.6 STOPPING THE GENERATOR

1. Turn OFF all electrical loads using the means provided (such as a main circuit breaker or transfer switch).

2. Let generator run at no-load for a few minutes, to stabilize internal engine generator temperatures.

3. Place the Start/Stop switch in its STOP position.

2.7 APPLYING LOADS TO GENERATOR

When applying electrical loads to the generator, observe these guidelines:

• Before applying electrical loads, let the generator

stabilize and warm up for a minute or two.

• DO NOT overload the generator.

2.7.1 LETTING THE ENGINE STABILIZE



The generator supplies correct rated voltage only at the proper governed speed. Some electrical appliances may be extremely sensitive to voltage. Incorrect voltages can damage such appliances.

If electrical loads are applied at reduced operating speeds, such loads imposed on the engine when sufficient power is not available may shorten engine life. Never turn ON electrical loads until after the generator engine has started and stabilized at no-load.

2.8 DO NOT OVERLOAD THE

• Induction type motors (such as those that run the vehicle’s furnace fan, refrigerator, air conditioner, etc.) need about 2-1/2 time more watts of power for starting than for running (for a few seconds during motor starting). Be sure to allow for this when connecting electrical loads to the generator. First, figure the watts needed to start electric motors in the system. To that figure, add the running wattages of other items that will be operated by the generator.

• Do not apply heavy electrical loads for the first two or three hours of operation.

2.9 PROTECTION SYSTEMS

2.9.1 LOW OIL PRESSURE SWITCH



This switch (Figure 2.2) has normally closed (N.C.) contacts that are held open by engine oil pressure during cranking and operating. Should oil pressure drop below a preset level, switch contacts close, and the engine automatically shuts down. The unit should not be restarted until oil is added.

2.9.2 HIGH TEMPERATURE SWITCH



This switch (Figure 2.2), which has normally open (N.O.) contacts, is mounted near the oil filter. The contacts close if the temperature should exceed approximately 284º F (140º C), initiating an engine shutdown.

GENERATOR

Read the rated wattage/amperage capacity of the generator on the generator data label (see Section 1.1).

Applying electrical loads in excess of the unit’s rated capacity will cause the engine/generator to automatically shut down.

To avoid overloading, add up the wattage of all connected electrical lighting, appliance, tool and motor loads. This total should not be greater than the generator’s rated wattage capacity.

• Most lighting, appliance, tool and motor loads indicate their required watts on their nameplate or data plate. For light bulbs, simply note the wattage rating of the bulb.

• If a load does not show its rated wattage, multiply that load’s rated VOLTS times AMPS to obtain WATTS.

Figure 2.2 – Low Oil Pressure and

High Temperature Switches

High Temperature Switch

Low Oil Pressure Switch

Section 2 – Operation

Recreational Vehicle Generator

2.9.3 FIELD BOOST



The Controller Circuit Board houses a field boost diode and resistor that are not part of the automatic choke circuit. These two components are part of a “field boost” circuit (Figure 2.3). During engine cranking only, a positive DC (battery) voltage is delivered through the diode, resistor, brushes and slip rings, to the generator rotor. Application of this voltage to the rotor “flashes the field” whenever it is started. Flashing of the field each time the generator starts makes sure that a sufficiently strong magnetic field is available to produce “pickup” voltage in the stator windings.

Figure 2.3 – Field Boost Circuit

The voltage regulator also incorporates a “voltage surge protection circuit.” This circuit prevents troublesome surges in the generator AC output voltage. Voltage surge is a common cause of damage to electronic equipment.

2.10 ADDITIONAL INFORMATION

2.10.1 25-HOUR BREAK-IN PERIOD



The first 25 hours of operation is the break-in period for the generator. Properly breaking in the generator is essential to minimize fuel consumption and provide maximum engine performance. During this 25-hour break-in period, follow this procedure:

• Run the unit at varying electrical loads to help seat the engine piston rings properly.

• Check the engine oil level frequently. Add oil if needed. It is normal for the generator engine to consume more oil than is normal until the piston rings have properly seated.

• For the 75-hour operation following the break-in period, avoid light electrical loads. Load the generator at 50 percent (or more) of its rated wattage capacity. Repeated light loads during these 75 hours can cause improper seating of engine piston rings, resulting in blowby and high oil consumption.

• After operating the unit for 25 hours, complete the tasks recommended under Section 2.10.2.

2.9.4 OVERVOLTAGE PROTECTION



A solid-state voltage regulator (Figure 2.4) controls the generator’s AC output voltage. This regulator supplies an excitation current to the rotor. By regulating the rotor’s excitation current, the strength of its magnetic field is regulated and, in turn, the voltage delivered to connected electrical loads is controlled. When the AC frequency is 60 Hertz, voltage is regulated at 120 volts (voltage-to-frequency ratio is 2-to-1).

Figure 2.4 – Solid State Voltage Regulator



2.10.2 25-HOUR CHECK-UP

After the 25-hour break-in period, contact an Authorized Service Dealer for the following maintenance. The vehicle owner is responsible for any charges:

• Change the engine crankcase oil and oil filter.

• Check the oil level.

• Inspect the cooling and ventilation openings.

• Check the engine carburetor adjustments.

• Check the engine ignition system.

• Inspect the entire electrical system.

• Inspect the engine exhaust system.



2.10.3 ATTENTION REQUIRED AFTER SUBMERSION

If the recreational vehicle generator has been submerged in water, it MUST NOT be started and operated. Following any submersion in water, have an Authorized Service Dealer thoroughly clean and dry the generator.

2.10.4 OPERATION IN HIGH GRASS



OR BRUSH

Never operate the generator while the vehicle is parked over high grass, weeds, brush, leaves or any other combustible substance. Such materials can ignite and burn from the heat of the exhaust system. The generator exhaust system becomes extremely hot during operation and remains hot for a long time after it has shut down.

2.10.5 EFFECTS OF MOISTURE AND DIRT



Keep the generator set as clean and dry as possible. Protect the unit against excessive dust, dirt, corrosive vapors, road splash, etc. Permitting dirt and moisture to accumulate on generator windings will have an adverse effect on the insulation resistance of those windings.

When moisture is allowed to remain in contact with windings, some of the moisture will be retained in voids and cracks in the insulation. This causes a reduced insulation resistance and will eventually cause problems. Dirt will make the problem worse, since dirt tends to hold moisture in contact with windings. Salt (as from sea air) also will worsen the problem since it tends to absorb moisture from the air. Salt and moisture, when combined, form a good electrical conductor.

Section 3 – Maintenance

Recreational Vehicle Generator

3.1 CHECKING THE ENGINE OIL LEVEL

For oil capacities and requirements, see “Engine Oil Requirements,” Section 1.5.4. Check the engine crankcase oil level at least every eight hours of operation, or before each use. To check the engine oil level, proceed as follows (see Figure 3.1):

1. Be sure the generator is as level as possible.

2. Remove the dipstick and wipe it dry with a clean,

lint-free cloth.

3. Install and tighten the dipstick cap; then, remove

it again. The oil level should be at the dipstick “Full” mark.

4. If necessary, remove the oil fill cap on the rocker

cover and slowly add oil until it reaches the dipstick “Full” mark. DO NOT FILL ABOVE THE “FULL” MARK.

Never operate the engine with the oil level



below the “Add” mark on the dipstick. Doing this could damage the engine.

5. Install and tighten the oil fill cap and the dipstick

before operating the engine.

3.2 CHANGING THE ENGINE OIL AND/OR OIL FILTER

• Change the engine oil after the first 25 hours of

operation (after the 25-hour break-in period, see Section 2.10.1). Thereafter, change the oil every 100 operating hours. Change the oil more frequently if operating consistently under heavy load or at high ambient temperatures.

Figure 3.1 – Oil Maintenance Features

GENERAC

POWERED

OHVI

QUIETPACT 40G

GENERAC OHVI INDUSTRIAL ENGINE

RV SERVICE LOCATOR:

1.800.333.1322

Oil Dipstick/Oil Fill

Oil Drain Oil Filter

CONTROL CENTER

FUEL

START

STOP

PRIME

FUSE

7.5 A

SERVICE ACCES S PANEL

AIR FILTER LOCATED BEHIND PANEL.

MAINTENANCE SCHEDULE

OIL LEVEL: CHECK DAILY

AIR FILTER: CLEAN PREFILTER

EVERY 100 HOURS. REPLACE ELEMENT EVERY 250 HOURS.

OIL & OIL FILTER:

CHANGE EVERY 100 HOURS. (OR ANNUALLY)

PERFORM MORE OFTEN IN DUSTY CONDITIONS

INSPECT & CLEANSPARK PLUGS: PLUGS EVERY 100 HOURS. REPLACE PLUGS EVERY 500 HOURS. (IF NECESSARY)

FUEL FILTER: CHANGE EVERY 400

HOURS. (OR ANNUALLY)

REPLACEMENT INFORMATION

PREFILTER P/N: 0D4511

AIR FILTER P/N: 0D3262

SPARK PLUG P/N: 072347

FUEL FILTER P/N: 0D7515

OIL CAPACITY WITH FILTER:

TEMPERATURE SAE VISCOSITY

32˚F AND HIGHER

10˚F TO 100˚F

0˚F TO 80˚F

-20˚F TO 50˚F 5W-30

WHEN SERVICE OR PARTS ARE NEEDED IN

THE USA OR CANADA, CONTACT THE GENERAC

SERVICE LOCATOR AT 1-800-333-1322.

C.B. 30A

070185OIL FILTER P/N:

0.8L/0.84QT

15W-40

10W-30

Section 3 – Maintenance

Recreational Vehicle Generator

• Change the engine oil filter after the first 25 hours of operation, and every 100 operating hours thereafter.

To change the oil and/or oil filter, proceed as follows

(see Figure 3.1):

1. Run the engine until it is thoroughly warmed up

(at least five minutes) then shut OFF the engine.

2. Immediately after the engine shuts OFF, pull the

oil drain cover free of the base. Remove the plug from the tube with a 5/16” allen wrench and drain the oil into a suitable container. Loosening the oil fill cap will allow the crankcase to drain faster.

3. After the oil has drained, replace the plug onto the

end of the oil drain tube. Retain the cover in the base.

4. With the oil drained, remove the old oil filter by

turning it counterclockwise. Place a towel underneath to catch excess oil.

5. Apply a light coating of clean engine oil to the gas-

ket of the new filter. Fill the filter until saturated with clean oil.

6. Screw the new filter on by hand until its gasket

lightly contacts the oil filter adapter. Then, tighten the filter an additional 3/4 to one turn.

7. Remove the dipstick and wipe it dry with a clean,

lint-free cloth. This will be used later to check the oil level.

8. Remove the oil fill cap on the oil fill tube and

slowly add the proper type and amount of recommended oil (see Section 1.5.4). Periodically use the dipstick to check the oil level and continue to fill the crankcase until the oil reaches the dipstick “Full” mark. DO NOT FILL ABOVE THE “FULL” MARK.

9. Install and tighten the oil fill cap and the dipstick

before operating the engine.

10. Start the engine and check for leaks.

NOTE:

Check the oil level and fill to the “FULL” mark after checking for leaks. The filter will retain some oil.

3.3 MAINTAINING THE ENGINE

AIR CLEANER

4. Wash the foam precleaner in liquid detergent and water.

5. Wrap the foam precleaner in a clean cloth and gently squeeze it dry.

6. Saturate the foam precleaner in clean engine oil. Gently squeeze it in a clean cloth to remove excess oil and to distribute oil (DO NOT TWIST).

7. Install the foam precleaner into the cover, followed by the paper filter.

8. Install the cover, foam precleaner and paper filter.

9. Tighten the two screws to retain the filter in place.

Figure 3.2 – Engine Air Cleaner

3.3.2 CLEANING OR REPLACING



THE PAPER FILTER

Once each year or every 100 hours of operation (whichever comes first), clean or replace the paper filter. The new replacement filter must be flame retardant. Service the paper filter more frequently if operating the generator in extremely dusty or dirty conditions. Use the following procedure (Figure 3.2):

1. Follow steps 1-3 in Section 3.3.1; service the foam precleaner if necessary.

2. Remove the paper filter.

3. Clean the air filter by tapping it gently on a solid surface. If the filter is too dirty, replace it with a new one. Dispose of the old filter properly.

4. Clean the air cleaner cover then reassemble following steps 7-9 in Section 3.3.1.

3.3.1 CLEANING THE FOAM PRECLEANER



Clean and re-oil the foam precleaner every three months or every 25 hours of operation, whichever occurs first. Service the foam precleaner more frequently if operating the generator in extremely dusty or dirty conditions. Use the following procedure (Figure 3.2):

1. Turn the two screws counterclockwise to loosen.

2. Remove the cover, foam precleaner and paper filter.

3. Remove the foam precleaner from the cover.

Section 3 – Maintenance

USTC

Recreational Vehicle Generator

3.4 CLEAN AIR INTAKE

Clean all foreign material from the air intake (Figure

3.3) at least once every 100 hours of operation. Clean more often if necessary.

Inspect the area around the generator exhaust muffler periodically and remove all grass, leaves, dirt, etc., from this area.

Figure 3.3 – Cleaning Air Intake

USTC

3.5 CHECKING THE ENGINE SPARK PLUG

Clean the spark plug and reset the spark plug gap every 100 hours of operation.

1. Clean the area around the base of the spark plug

to keep dirt and debris out of the engine. Remove the spark plug and check the condition. Replace the spark plug if worn or if reuse is questionable.

2. Clean spark plug by scraping or washing using a

wire brush and commercial solvent. Do not blast the spark plug to clean.

3. Check the spark plug gap using a wire feeler

gauge. Adjust the gap to 0.030 inch (0.76 mm) by carefully bending the ground electrode (Figure

3.4).

Figure 3.4 – Setting the Spark Plug Gap

3.6 FUEL FILTER

Remove and replace the fuel filter (Figure 3.5) once each year or every 400 hours of operation, whichever comes first. Fuel filter is removed with a 15/16” deep well socket.

Figure 3.5 – Fuel Filter

POS

FUEL

NEG

3.7 CLEAN SPARK ARRESTOR

The engine exhaust muffler has a spark arrestor screen. Inspect and clean the screen every 50 hours of operation or once each year, whichever comes first.

NOTE:

If using the generator on any forest-covered, brush-covered or grass-covered unimproved land, it must equipped with a spark arrestor. The spark arrestor must be maintained in good condition by the owner/operator.

Clean and inspect the spark arrestor as follows:

• Remove the screen retaining bracket by removing the screw.

• Slide the spark arrestor screen out from the tail pipe.

• Inspect screen and replace if torn, perforated or otherwise damaged. DO NOT USE a defective screen. If screen is not damaged, clean it with commercial solvent.

• Replace the screen and the retaining bracket.

 Sparking can occur if the wire terminal does not

fit firmly on the spark plug terminal end. If necessary, re-form the wire terminal to obtain a tight fit.

Figure 3.6 - Spark Arrestor

TAILPIPE P/N 0E0683

SPARK ARRRESTOR SCREEN P/N 089680

RETAINING SCREW P/N 056892

Section 3 – Maintenance

Recreational Vehicle Generator

3.8 CLEANING THE GENERATOR

Do NOT use a forceful spray of water to clean



the generator. Water will enter the generator interior and cause problems, and may also contaminate the generator fuel system.

3.9 BATTERY MAINTENANCE

All lead-acid batteries will discharge when not in use. The generator battery should be inspected as follows:

DANGER

Do not dispose of the battery in a fire. The



battery is capable of exploding. Storage batteries give off explosive hydrogen gas. This gas can form an explosive mixture around the battery for several hours after charging. The slightest spark can ignite the gas and cause an explosion. Such an explosion can shatter the battery and cause blindness or other injury. Any area that houses a storage battery must be properly ventilated. Do not allow smoking, open flame, sparks, or any spark producing tools or equipment near the battery. Discharge static electricity from body before touching the battery by first touching a grounded metal surface.

A battery presents a risk of electrical shock



and high short circuit current. The following precautions are to be observed when working on batteries:

• Remove watches, rings or other metal objects;

• Use tools with insulated handles;

• Wear rubber gloves and boots;

• Do not lay tools or metal parts on top of the

battery;

• Disconnect any charging source prior to connecting

or disconnecting battery terminals; and

• Do not use any jumper cables or booster battery to

crank and start the generator engine. If any battery has discharged, remove it for recharging.

3.9.1 WEEKLY



• Inspect the battery posts and cables for tightness and corrosion. Tighten and clean as necessary.

• Check the battery fluid level of unsealed batteries and, if necessary, fill with Distilled Water Only. Do not use tap water in batteries.



3.9.2 EVERY SIX MONTHS

• Have the state of charge and condition checked. This should be done with an automotive-type battery hydrometer.

NOTE:

Servicing of the battery is to be performed or supervised by personnel knowledgeable of batteries and the required precautions. Keep unauthorized personnel away from batteries.

Damage will result if the battery connections are made in reverse.

Do not open or mutilate the battery. Released



electrolyte has been known to be harmful to the skin and eyes, and to be toxic.

The electrolyte is a dilute sulfuric acid that is



harmful to the skin and eyes. It is electrically conductive and corrosive. The following procedures are to be observed:

• Wear full eye protection and protective clothing;

• Where electrolyte contacts the skin, wash it off immediately with water;

• Where electrolyte contacts the eyes, flush thoroughly and immediately with water and seek medical attention; and

• Spilled electrolyte is to be washed down with an acid neutralizing agent. A common practice is to use a solution of 1 pound (500 grams) bicarbonate of soda to 1 gallon (4 liters) or water. The bicarbonate of soda solution is to be added until the evidence of reaction (foaming) has ceased. The resulting liquid is to be flushed with water and the area dried.

Section 3 – Maintenance

Recreational Vehicle Generator

3.10 MAJOR SERVICE MANUAL

To obtain a service manual for the generator, contact the nearest Authorized Service Dealer. Make sure to identify the MODEL NUMBER and SERIES.

3.11 EXERCISING THE GENERATOR

The manufacturer recommends that the generator be started and operated at least once every seven days. Let the unit run for at least 30 minutes to “exercise” the engine.

3.12 OUT OF SERVICE PROCEDURE

3.12.1 REMOVAL FROM SERVICE



If the generator cannot be exercised every seven days, and it is to be out of service longer than 30 days, prepare the generator for storage as follows:

1. Start the engine and let it warm up.

2. Close the fuel shutoff valve in the fuel supply line and allow the unit to shut down.

Note:

Using a fuel additive such as STA-BIL fuel stabilizer, or an equivalent, will prevent gum deposits from forming in the engine’s fuel system.

3. While the engine is still warm from running, drain the oil completely. Refill the crankcase with SAE 10W-30 oil having API classification “For Service SF.”

4. Attach a tag to the engine indicating the viscosity and classification of the oil in the crankcase.

5. Remove the spark plug and pour two or three tablespoons of clean, fresh engine oil into the spark plug threaded openings. Reinstall and tighten the spark plug.

6. Remove the battery and store it in a cool, dry room on a wooden board. Never store the battery on any concrete or earthen floor.

7. Clean and wipe the entire generator.

4. Reconnect the battery. Observe battery polarity. Damage may occur if the battery is connected incorrectly.

5. Turn OFF all electrical loads. Add fuel if necessary and then start the engine.

6. Allow the unit to run for several minutes to warm up.

7. Apply electrical loads to at least 50 percent of the unit’s rated wattage capacity.

8. When the engine is thoroughly warmed up, shut it down.

9. The generator is now ready for service.

3.13 ADJUSTING VALVE CLEARANCE

After the first 50 hours of operation, adjust the valve clearance in the engine.

When adjusting valve clearance, the engine should be at room temperature and the piston should be at Top Dead Center (TDC) of its compression stroke (both valves closed). Correct clearance is 0.001-0.003 inch (0.03-0.07mm). Adjust valve clearance as follows:

1. Loosen the rocker arm jam nut. Use an allen wrench to turn the pivot ball stud while checking clearance between the rocker arm and the valve stem with a feeler gauge (Figure 3.7).

Figure 3.7 — Adjusting Valve Clearance

3.12.2 RETURN TO SERVICE



To return the unit to service after storage, proceed as follows:

1. Check the tag on the engine for oil viscosity and classification. Verify that the correct recommended oil is used in the engine (see Section 1.5.4). If necessary, drain and refill with the proper oil.

2. Check the state of the battery. Fill all cells of unsealed batteries to the proper level with distilled water. DO NOT USE TAP WATER IN THE BATTERY. Recharge the battery to 100 percent state of charge, or, if defective, replace the battery.

3. Clean and wipe the entire generator.

Section 3 – Maintenance

Recreational Vehicle Generator

2. When valve clearance is correct, hold the pivot ball stud with the allen wrench and tighten the rocker arm jam nut with a crows foot. Tighten the jam nut to 65-85 inch-pounds torque. After tightening the jam nut, recheck valve clearance to make sure it did not change (Figure 3.8).

Figure 3.8 — Tightening Jam Nut

3.14 RV GENERATOR SERVICE INTERVAL

50 Hours ................................ Clean Spark Arrestor

100 Hours ...........................Change Engine Oil/filter

100 Hours .................................. Clean Air Pre-filter

100 Hours ................................ Inspect Spark Plugs

250 Hours ............ Replace Paper Air Filter Element

400 Hours ...................................Replace Fuel Filter

500 Hours ................................Replace Spark Plugs

1st 50 Hours-then

every 500 Hrs. .......................... Adjust Valve Lash

PART II –

INSTALLATION

INSTRUCTIONS

DANGER

ONLY QUALIFIED ELECTRICIANS OR CONTRACTORS

SHOULD ATTEMPT INSTALLATION!!

Safety Rules

Recreational Vehicle Generator

DANGER: For fire safety, installation of a generator into a recreational vehicle must comply

strictly with article 551, NFPA 70; ANSI C1-1975; AND, ANSI A119.2-1975/NFPA 501C “Standard



for Recreational Vehicles” (Part 3, “Installation of Electrical Systems”). In addition, installation must comply with the manufacturer’s instructions and recommendations.

NOTICE TO INSTALLER

These Installation Instructions have been published by the manufacturer to aid in the installation of the products described in this manual. The manufacturer assumes that installation personnel are familiar with the procedures for installing such products, or similar products manufactured. The manufacturer also assumes that personnel have been trained in the recommended installation procedures for these products and that such training includes (a) use of common hand tools, (b) use of special tools, and (c) use of any tools and/or equipment from other suppliers.

The manufacturer cannot possibly know of and advise the recreational vehicle trade of all conceivable methods, procedures or techniques by which to perform an installation. Nor can we anticipate every possible hazard that might result from each installation method, procedure or technique. The manufacturer has not undertaken any such wide evaluation. Therefore, people who use a method, procedure or technique that the manufacturer does not specifically recommend must first completely satisfy themselves that their safety, the safety of the vehicle's occupants and the product's safety is not endangered by the method, procedure or technique selected.

Information, illustrations, specifications, etc., contained in these Installation Instructions are based on the latest information available at the time of publication. Every effort has been expended to be sure that such data is both accurate and current. However, the manufacturer reserves the right to change, alter or otherwise improve this product at any time without prior notice.

DANGER

Despite the safe design of this generator,



Potentially lethal voltages are generated by



these machines. Ensure all steps are taken to render the machine safe before attempting to work on the generator.

Parts of the generator are rotating and/or hot



during operation. Exercise care near running generators.

• For safety reasons, the manufacturer recommends

that the installation, initial start-up and maintenance of this equipment is carried out by an Authorized Service Dealer.

• The engine exhaust fumes contain carbon monox-

ide, which can be DEADLY. This dangerous gas, if breathed in sufficient concentrations, can cause unconsciousness or even death. This exhaust system must be installed properly, in strict compliance with applicable codes and standards. Following installation, do nothing that might render the system unsafe or in noncompliance with such codes and standards. The generator compartment must be completely vapor sealed from the vehicle interior. There must be no possibility of exhaust fumes entering the vehicle interior. Never operate this equipment with a leaking or defective exhaust system.

• Keep hands, feet, clothing, etc., away from drive

belts, fans, and other moving or hot parts. Never remove any drive belt or fan guard while the unit is operating.

• Adequate, unobstructed flow of cooling and ven-

tilating air is critical to correct generator operation and is required to expel toxic fumes and fuel vapors from the generator compartment. Without sufficient cooling airflow, the engine/generator quickly overheats, which causes serious damage to the generator. Do not alter the installation or permit even partial blockage of ventilation provisions, as this can seriously affect safe operation of the generator.

• When working on this equipment, remain alert

at all times. Never work on the equipment when physically or mentally fatigued.

• Before performing any maintenance on the gen-

erator, disconnect its battery cables to prevent accidental start up. Disconnect the cable from the battery post indicated by a NEGATIVE, NEG or (–) first. Reconnect that cable last.

• Never use the generator or any of its parts as a

step. Stepping on the unit can stress and break parts, and may result in dangerous operating conditions from leaking exhaust gases, fuel leakage, oil leakage, etc.

• Never insert any tool or other object through open-

ings in the generator interior, even if the unit is not running. Serious injury or damage to the equipment may occur.

GENERAL HAZARDS



Safety Rules

Recreational Vehicle Generator

ELECTRICAL HAZARDS



• Do not handle any kind of electrical device while standing in water, while barefoot, or while hands or feet are wet. DANGEROUS ELECTRICAL SHOCK MAY RESULT.

• During installation onto the vehicle, properly ground (bond) the generator either by solid mounting to the vehicle frame or chassis, or by means of an approved bonding conductor. DO NOT connect the bonding conductor to any generator part that might be removed or disassembled during routine maintenance. If the grounding conductor must be replaced, use only a flexible conductor that is of No. 8 American Wire Gauge (AWG) copper wire minimum.

• If the vehicle electrical circuits can be powered by any other source of electricity (such as a “dockside” power receptacle), there must be no possibility of connecting the different power sources to the vehicle circuits at the same time. The dockside (utility) power source must be positively isolated from the vehicle circuits whenever the generator is operating. Failure to isolate the vehicle circuits from the dockside power supply when the generator is running may result in damage to the generator or serious injury or death to dockside (utility) power workers due to backfeed of electrical energy.

• Never wear jewelry when working on this equipment. Jewelry can conduct electricity resulting in electric shock, or may get caught in moving components causing injury.



FIRE HAZARDS



EXPLOSION HAZARDS



• Fuel lines must be properly installed and fastened, and free of leaks. There must be no possibility of gasoline vapors entering the vehicle interior.

• It is required to install an approved, flexible, nonconductive fuel line between the generator fuel connection point and rigid fuel lines.





Section 1 – General Information

Recreational Vehicle Generator

1.1 PURPOSE AND SCOPE OF THE MANUAL

These Installation Instructions have been prepared especially for the purpose of familiarizing installers and owners of the applicable equipment with the product's installation requirements. Give serious consideration to all information and instructions in the manual, both for safety and for continued reliable operation of the equipment.

Because of the different recreational vehicle models and the variations between the models, it would be extremely difficult, if not impractical, to provide detailed instructions for every possible installation. For that reason, instructions and illustrations in this manual are general in nature. Illustrations are not intended to serve as detailed installation blueprints.

The installation should comply strictly with all applicable codes, standards and regulations pertaining to the installation and use of this product. If any portion of this manual appears to be in conflict with such codes, standards or regulations, the applicable codes, standards or regulations must take precedence over the manual.

6. CSA Electrical Bulletin 946, available from the Canadian Standards Association, Housing and Constructions Materials Section, 178 Rexdale Boulevard, Rexdale, Ontario, Canada, M9W 1R3.

1.4 EQUIPMENT DESCRIPTION

Instructions and information in this section pertain to air-cooled generators. This generator is designed specifically for installing in recreational vehicles. This generator operates 120-volts, single-phase, 60-Hertz, AC electrical loads that require 30.0 amps.

1.5 GENERATOR ENGINE

OPERATING SPEED

The generator’s revolving field (rotor) is driven by a single-cylinder, four-cycle engine. The generator supplies 120 volts AC at 60 Hertz when the rotor is operating at 3,600 rpm.

1.6 GENERATOR AC

CONNECTION SYSTEM

The generator is equipped with dual stator power windings as shown in Figure 1.1.

1.2 SAFETY

Before handling, installing, operating or servicing this equipment, carefully read the “Notice to Installer” and “Safety Rules”. Comply with all safety rules to prevent death, personal injury or damage to equipment and/or property. Stress safety to all installers, operators and service technicians who work on this equipment.

1.3 STANDARDS BOOKLETS

Installation, use and servicing of this equipment should comply strictly with published standards, as well as the manufacturer's recommendations. The following standards booklets (latest revision) are available from the sources indicated:

1. NFPA Standard 501C, “Standard for Recreational Vehicles,” available from the National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.

2. NFPA 70, “NFPA Handbook of the National Electric Code,” available same as Item 1.

3. ANSI C1-1975 and ANSI 119.2-1975, available from the American National Standards Institute, 1430 Broadway, New York, NY 10018.

4. ANSI A119.2/NFPA 501C, available from the Recreational Vehicle Association, 1896 Preston White Drive, Reston, VA 22090.

5. California Administrative Code, Title 25, available from the State of California, Documents Section, P.O. Box 1015, North Highlands, CA 95660.

Figure 1.1 – 120-volt Single Voltage Connection

BLACK

• The AC connection system on air-cooled generators uses a GROUNDED neutral.

• A separate green ground wire is connected to the recreational vehicle’s junction box.

NOTE:

Do NOT connect loads in excess of circuit breaker ratings.

Section 1 – General Information

Recreational Vehicle Generator

Figure 1.2 – Major Features and Dimensions (Drawing No. 0D8716-G)

AC OUTPUT

HARNESS

REMOTE PANEL

CONNECTOR

REF.

483.1

[ 19"]

NOTE: ALL AIR INTAKES AND EXHAUST OUTLETS MUST BE

KEPT CLEAR OF ANY OBSTRUCTIONS. ALL OPEN AREA

IS REQUIRED FOR COOLING.

414.5 [ 16 5/16"]

360.5 [ 14 3/16"]

FUEL FILTER

BATTERY

CONNECTIONS

63.5

36.5 [ 1 7/16"]

48.1 [ 1 7/8"]

[ 2 1/2"]

222.7

OIL DRAIN

300.7

[ 8 3/4"]

369.7 [ 14 9/16"]

[ 11 13/16"]

[ 1 1/8"]

688.3

736.4

[ 27 1/8"]

[ 29"]

REF.

749.8 [ 29 1/2"]

342.2 [ 13 1/2"]

FRONT DOOR ACCESS FOR

ALL REQUIRED MAINTENANCE

EXIT

TAIL PIPE

223.5

83.5

[ 3 1/8"]

101

[ 4"]

[ 8 13/16"]

176.6

[ 3 5/16"]

[ 6 15/16"]

118

[ 4 5/8"]

50.8

[ 2 3/8"]

[2"]

170

210

[ 6 11/16"]

[ 8 1/4"]

HOT AIR

EXHAUST

AIR

416

INTAKE

[ 16 3/8"]

5/16"-18 WELDNUTS

(6 PLACES)

717.7 [ 28 1/4"]

343.4

423.2 [ 16 11/16"]

TYP.

6.7

[ 13 1/2"]

82.5

[ 1/4"]

[ 3 1/4"]

VIEW FROM TOP

476.4 [ 18 3/4"]

429.5 [ 16 15/16"]

376.5 [ 14 13/16"]

55.5 [ 2 3/16"]

Section 2 – Installation

Recreational Vehicle Generator

2.1 LOCATION AND SUPPORT

2.1.1 GENERATOR LOCATION



The most desirable location for the generator set is between the vehicle's main frame members. However, this is seldom possible. Most units must be installed on the side of the vehicle and are difficult to reinforce.

Many recreational vehicles have been factory equipped with an area for the generator set. Some vehicles may even have a generator compartment provided by the vehicle manufacturer.

Plan the generator location based on the following:

• The generator set must be installed on a framework that is part of the recreational vehicle, as outlined in Section 2.1.2.

• The location must provide an access opening that is large enough to permit generator removal (unless the generator is to be removed from underneath the supporting framework).

• The location must provide easy access to frequently serviced components, such as filters, oil drains, spark plugs and other common maintenance parts.

• The location must provide sufficient room to allow minimum clearances as outlined in Section 2.2. If sound insulation is to be used on the compartment walls and ceiling, the minimum recommended applies to the space between the generator and such insulation.

• The location must provide adequate cooling and ventilating airflow for the generator without a great deal of work and expense.

• If mounting the generator in an enclosed compartment, the base of the generator must rest flat on the floor without any gaps.

• When using a suspended mounting system, ensure the base of the generator is flush with the surrounding bodywork. If the unit is mounted higher in the structure, heated air may recirculate into the generator causing it to overheat.

2.1.2 GENERATOR SUPPORT



The generator must be securely attached to a metal framework that has been made part of the vehicle frame structure by bolting or welding. The metal framework on which the generator will rest and which will restrain the generator set should consist of at least two horizontal beams. These beams should consist of (a) 1-1/2-inch square, 11-gauge steel tubing OR (b) 1-1/2-inch, 11-gauge angle iron. A typical supporting frame with horizontal support tubing, is shown in Figure 2.1.

The generator can be installed so that it sits on top of the horizontal support tubing if the vehicle design permits. Another method is to suspend the generator below the horizontal support tubing by means of suitable, structurally sound metal framework. The following general rules apply:

• Vehicle construction MUST be capable of supporting the weight of the generator.

• Whether the generator is mounted above the horizontal support tubing or suspended below the tubing, the supporting frame used must be structurally sound.

• If the generator cannot be bolted directly to the supporting frame or support tubing, consider using additional tubing, angle brackets or other supports to give the supporting frame sufficient strength.

Figure 2.1 – Typical Horizontal Support Frame

2.1.3 SUSPENDED MOUNTING



If the generator will be suspended below the horizontal support tubing, the suspension method used with the vehicle frame members must (a) be able to support the weight of the generator AND (b) provide sufficient restraint for the generator. One typical suspended mounting system is shown in Figure 2.2. The location of a suspended mounting system must be carefully planned, keeping the following general rules in mind:

• Protect the generator against road splash and debris. Baffles or splash guards may be required to protect certain areas of the generator. To make sure the generator is adequately protected, road test the installation through mud, water and slush.

Figure 2.2 – Typical Suspended Mounting System

GENERATOR SUPPORT FRAME (MODEL 004718-0)

GENERATOR MOUNTING HOLES FOR 5/16" - 18 BOLTS (6 PLACES)

Section 2 – Installation

Recreational Vehicle Generator

• The installer must make certain that the selected location will permit adequate cooling and ventilating airflow to be supplied.

2.1.4 GENERATOR RESTRAINT



Use four 5/16"-18 hardened steel bolts (Grade 5) to fasten the generator to the supporting frame or the support tubing. These bolts must pass through (a) the generator mounting base, (b) the compartment floor (if a compartment is used) and (c) the supporting framework (Figure 2.3). All bolts must be long enough so that when tight, at least three threads are visible past the retaining lock nuts. Refer to Section

2.2 for the location of the generator mounting holes.

Figure 2.3 – Typical Generator Restraint

NOTE:

Refer to “Figure 1.2 – Major Features and Dimensions”.

2.2.2 COMPARTMENT CONSTRUCTION



• The generator compartment should be either constructed of, or lined with, 26-gauge galvanized steel.

NOTE:

Aluminum is NOT an acceptable alternative to galvanized steel due to aluminum’s low melting point.

• If the compartment is lined with galvanized steel, it may be constructed of any material. The manufacturer recommends that the compartment be constructed of 1/2-inch thick plywood (not strandboard), with the floor made of a double thickness of 1/2-inch plywood with the grain of the wood at cross section for added strength (Figure 2.5).

Figure 2.5 – Typical Compartment Construction

2.2 GENERATOR COMPARTMENTS

Whether the generator set is being installed inside a compartment specifically manufactured to house a generator or inside a compartment that the installer constructs, the compartment must meet certain specifications as outlined in the following sections:

2.2.1 COMPARTMENT SIZE



Plan the compartment size carefully. Provide a minimum clearance of 1/2 inch (13 mm) on the front and top, 1/2 inch (25 mm) on the sides, and 1/2 inch (13 mm) from the back for air circulation AFTER the compartment has been lined with metal and sound insulation (Figure 2.4).

Figure 2.4 – Clearances

Plywood

Compartment

Insulation

1/2" Clearance on Top

1/2"

in Front

1" Clearance

in Back

1" Each Side

18" Clearance Recommended

Below (Minimum 12")

• If constructing a compartment, line the exterior (underside) of the compartment floor with 26gauge galvanized steel.

• All seams, splices and joints of the compartment walls (unless vapor tight by design) should be caulked to prevent poisonous, flammable or explosive vapors from entering the vehicle interior.

NOTE:

Caulking must be done so that the caulking material will stay in place permanently. Pressing such materials as putty tape onto joints and seams is NOT acceptable. A high quality silicone rubber base sealant is recommended.

Section 2 – Installation

Recreational Vehicle Generator

• Holes and openings made in the compartment walls to allow for the passage of electrical conduit, conductors, hoses, cables, etc., into the vehicle living area must be sealed vapor tight with silicone rubber base sealant.

• If flexible metal conduit is used, it must be sealed internally at the end where it terminates inside the compartment’s electrical junction box.

NOTE:

Flexible metal conduit, due to its unique construction, is NOT vapor tight along its entire length.

• Seams and joints of the galvanized steel (whether used as a liner or for the compartment itself) must be lapped and mechanically secured. Such seams may be manufactured, welded, bolted, riveted or screwed. Manufactured lock seams are shown in Figure 2.6. Installer constructed compartments typically utilize a standard lap joint.

Figure 2.6 – Types of Lock Seams

• After the compartment has been metal lined and vapor sealed, line the compartment interior walls and ceiling with an approved, nonflammable sound insulating material. See Section 2.2.3.

DANGER

Do not install any flammable material directly



above or around the compartment. Heat, transferred through the compartment structure, may be sufficient to ignite, char or discolor seat cushions, fiberboard and other flammable materials. Use approved nonflammable insulating materials in high temperature areas.

2.2.3 SOUND INSULATING MATERIALS



Once installers have determined that a compartment is properly constructed and metal lined, they can add acoustical material. This may include additional sealant or insulating material, to reflect noise away from the vehicle interior.

Sound insulating materials should be of a nonflam-

mable type. One excellent insulating material is a 1inch (25 mm) thick fiberglass having a 2-pound density. When fiberglass is used, its coated side should face toward the compartment interior.

DANGER

Do not install sound insulation or any absorbent



material on the compartment floor interior. Such materials will become soaked with combustible or explosive vapors and liquids and will become a fire hazard.

Using a combination of sound insulating materials can often reduce noise more effectively than a single material. For example, a sheet of lead or visco-elastic material, along with a layer of other acoustical material, is more effective than when a single material is used.

2.2.4 ACOUSTICS



For additional noise abatement, the installer may wish to consider the following:

• Using special sound insulating materials.

• Construction of a special noise abatement compartment.

NOTE:

Any method used to reduce noise must not adversely affect the flow of cooling and ventilating air into or out of the compartment.

In addition to the effective use of sound insulating materials, construction of a special noise abatement compartment might be considered to reduce noise levels. Such a compartment might be constructed as follows (Figure 2.7):

• Use 5/8-inch thick or 3/4-inch thick plywood in the compartment.

• Construct the compartment floor of a double thickness of 5/8-inch or 3/4-inch plywood.

• Line the compartment interior walls and floor, as well as the underside of the floor, with 26-gauge galvanized steel.

• Vapor seal all compartment seams and joints.

• Over the galvanized steel lining, install a combination of acoustical materials as mentioned in Section 2.2.3.

DANGER

To prevent fire or explosion, do not install any



insulation or other absorbent materials on the interior or underside of the compartment floor.

• Seal all compartment door edges to prevent noise leakage around the door perimeter.

Section 2 – Installation

Recreational Vehicle Generator

• Line the compartment door interior (except for air openings) with suitable, fireproof sound insulation (such as 1-inch (25 mm) thick fiberglass with a 2pound density).

Figure 2.7 – Typical Noise Abatement

Figure 2.8 – Compartment Floor Cutout (Drawing 0D8716-G)

VIEW FROM TOP

2.2.5 COMPARTMENT FLOOR CUTOUTS



Provide openings in the generator compartment for the following items (Figure 1.2):

• Engine exhaust and cooling air outlets

• Generator cooling air inlet

• Four holes for passage of generator mounting bolts. See Section 2.1.4.

DANGER

Fuel lines and exhaust piping must not pen-



etrate into the vehicle living area.

476.4

[ 18 3/4"]

429.5

[ 16 15/16"]

[ 2 3/16"]

[ 14 13/16"]

55.5

376.5

TYP.

[ 1/4"]

416

[ 16 3/8"]

48.1

[ 1 7/8"]

[ 1 1/8"]

6.7

HOT AIR

EXHAUST

TAIL PIPE

EXIT

222.7

[ 8 3/4"]

423.2

[ 16 11/16"]

82.5

[ 3 1/4"]

50.8 [2"]

101

[ 4"]

[ 11 13/16"]

300.7

210

[ 8 1/4"]

343.4

[ 13 1/2"]

[ 14 9/16"]

369.7

717.7

[ 28 1/4"]

[ 3 1/8"]

REF.

[ 2 3/8"]

688.3

[ 27 1/8"]

AIR

INTAKE

83.5

[ 3 5/16"]

36.5 [ 1 7/16"]

OIL DRAIN

736.4 [ 29"]

5/16"-18 WELDNUTS (6 PLACES)

170

[ 6 11/16"]

176.6

[ 6 15/16"]

118

[ 4 5/8"]

223.5

[ 8 13/16"]

63.5

[ 2 1/2"]

360.5

[ 14 3/16"]

414.5

[ 16 5/16"]

NOTE: ALL AIR KEPT CLE IS REQUIR

All measurements are in millimeters, 25.4 mm = 1”.

Section 2 – Installation

Recreational Vehicle Generator

2.3 COOLING AND VENTILATING AIR

It is absolutely essential that an adequate flow of air for cooling, ventilating and engine combustion be supplied to the generator set. Without sufficient airflow, the engine/generator quickly overheats. Such overheating can cause serious operating difficulties and also may cause fire and personal injury. The installer must make sure that sufficient air is available to the generator for cooling, ventilating and combustion. The installer also must provide for a path for exhausting the cooling air to the exterior of a compartment, if so equipped.

2.3.2 TESTING THE INSTALLATION



The manufacturer recommends testing the installation to be sure adequate cooling airflow is available to the unit before placing the unit into service. If the unit shows signs of overheating, enlarge the air openings. Never place a unit into service until absolutely certain that cooling and ventilation is adequate.

NOTE:

Test the installation, especially if bringing in air from below the generator set.

DANGER

Never use discharged cooling air for heating or



permit such air to enter the vehicle interior. This air contains deadly carbon monoxide gas and other poisonous, flammable or explosive gases.

2.3.1 GENERATOR AIRFLOW



Engine operation drives cooling fans for the two-stage cooling air system. A pressure fan draws cooling air into the bottom right side of the generator (Figure 2.9). This airflow cools the engine/generator and electronic components. The second part of the cooling system, a suction fan, draws air that is heated from a hot engine into a collector compartment at the left side of the unit. This heated air (although cooler than exhaust muffler) is then deflected out the bottom toward the ground.

Figure 2.9 – Airflow Through Engine/Generator

2.4 GASOLINE FUEL SYSTEM

The installation of a gasoline fuel system (Figure

2.10) for a recreational vehicle generator set must comply with applicable codes, standards and regulations. The entire fuel system must be completely free of leaks. There must be no possibility of gasoline vapors entering the vehicle interior.

Figure 2.10 – Generator Fuel System

CONTROL CENTER

C.B.

FUEL

START

30A

STOP

PRIME

FUSE

7.5 A

SERVICE ACCESS PANEL

AIR FILTER LOCATED BEHIND PANEL.

MAINTENANCE SCHEDULE

OIL LEVEL: CHECK DAILY

AIR FILTER: CLEAN PREFILTER

EVERY 100 HOURS.

* REPLACE ELEMENT EVERY 250 HOURS.

OIL & OIL FILTER:

CHANGE EVERY 100 HOURS. (OR ANNUALLY)

PERFORM MORE OFTEN IN DUSTY CONDITIONS

INSPECT & CLEANSPARK PLUGS: PLUGS EVERY 100 HOURS. REPLACE PLUGS EVERY 500 HOURS.

GENERAC

POWERED

OHVI

QUIETPACT 40G

GENERAC OHVI INDUSTRIAL ENGINE

RV SERVICE LOCATOR:

1.800.333.1322

Fuel Pump & Fuel Filter (Behind Access Panel & Air Filter)

(IF NECESSARY)

FUEL FILTER: CHANGE EVERY 400

HOURS. (OR ANNUALLY)

REPLACEMENT INFORMATION

PREFILTER P/N: 0D4511

AIR FILTER P/N: 0D3262

SPARK PLUG P/N: 072347

FUEL FILTER P/N: 0D7515

OIL CAPACITY WITH FILTER:

TEMPERATURE SAE VISCOSITY

32˚F AND HIGHER

10˚F TO 100˚F

0˚F TO 80˚F

-20˚F TO 50˚F 5W-30

WHEN SERVICE OR PARTS ARE NEEDED IN

THE USA OR CANADA, CONTACT THE GENERAC

SERVICE LOCATOR AT 1-800-333-1322.

070185OIL FILTER P/N:

0.8L/0.84QT

15W-40

10W-30

DANGER

Gasoline is highly flammable, and its vapors are



explosive. Comply with all codes, standards and regulations pertaining to gasoline fuel systems used in recreational vehicle generators. Properly install and maintain the fuel system and keep it entirely free of leaks. Gasoline vapors must not enter the vehicle interior.

Factory installed generator fuel system components include (a) fuel filter, (b) 12-volt DC electric pump, (c) engine carburetor, and (d) interconnecting lines and fittings. Connect a fuel supply line to the fuel filter inlet. Use a flexible length of approved fuel hose between the fuel filter inlet connection and rigid fuel lines.

2.4.1 FUEL TANK



Either the generator must share the vehicle engine's fuel tank, or install a separate fuel tank for the generator set. All fuel tanks installed on the vehicle must be constructed, installed and restrained so they comply with applicable codes, standards and regulations.

If the generator is to share the vehicle engine's tank, separate fuel pickup tubes are required for the engine and the generator. The manufacturer recommends that the fuel pickup tube be 2 to 3 inches (51 to 76 mm) shorter than the vehicle engine's pickup tube. This prevents the generator from depleting the entire fuel supply during prolonged generator operating periods.

Do NOT tee the generator fuel supply line



into the vehicle engine fuel supply line. If this is done, the generator will be starved of fuel when both engines are operating at the same time. Also, while the vehicle engine is not running, generator operation may drain the vehicle engine supply line, making it difficult to start the vehicle engine.

2.4.2 GENERATOR FUEL SUPPLY LINE



2.4.2.1 Rigid Fuel Lines

Those lines used to supply fuel from a tank to the generator must comply with applicable codes, standards and regulations. The following general rules apply to rigid fuel lines:

• Rigid lines should be of annealed, seamless, drawn aluminum or steel.

• Lines and fittings must comply with SAE J512F, “Standard Automotive Fittings,” or with ANSI B126.26 (latest edition).

• Route the fuel line so that at least 2 inches (51 mm) of clearance is maintained between the line and any exhaust system parts.

• Do not attach electrical wiring to fuel lines. Route the wiring so it cannot come into contact with any fuel line.

• Route fuel lines so if they leak, fuel does not drip onto any electrical or exhaust system parts.

• Use nonferrous metal straps without sharp edges to secure fuel lines.

Section 2 – Installation

Recreational Vehicle Generator

2.4.2.2 Flexible Fuel Line

Use an approved flexible length of fuel hose between the generator fuel inlet connection and rigid fuel lines. This prevents breaking of the line caused by vibration, shifting, settling or movement. The following rules apply:

• The flexible hose must comply with SAE J30B, “Standard for Fuel and Oil Hose.” It must be approved for use with gasoline.

• The hose should be at least 6 inches (152 mm) longer than is needed to prevent the hose from rupturing if the generator shifts or settles.

2.5 EXHAUST SYSTEM

The generator exhaust system must be safely and properly installed. Only approved mufflers and other exhaust system parts must be used. A properly installed exhaust system must be vapor tight, quiet and completely safe.

DANGER

The generator engine gives off DEADLY carbon



monoxide gas through its exhaust system. This dangerous gas, if breathed in sufficient concentrations, can cause unconsciousness or even death. Never operate the generator set with the vehicle inside any garage or other enclosed area. DO NOT OPERATE THE GENERATOR IF THE EXHAUST SYSTEM IS LEAKING OR HAS BEEN DAMAGED. SYMPTOMS OF CARBON MONOXIDE POISONING ARE (a) inability to think coherently; (b) vomiting; (c) twitching muscles; (d) throbbing temples; (e) dizziness; (f) headaches; (g) weakness; and (h) sleepiness. IF FEELING ANY OF THESE SYMPTOMS, MOVE INTO FRESH AIR IMMEDIATELY. IF SYMPTOMS PERSIST, GET MEDICAL HELP. Do not operate the generator until its exhaust system has been inspected and properly repaired.

Never tee the generator engine exhaust pipe



into the vehicle engine exhaust piping. This causes excessive back pressure on the generator engine. Also, water from one engine can damage the other engine.

]

Section 2 – Installation

Recreational Vehicle Generator

2.5.1 SPARK ARRESTOR



This spark arrestor assembly meets code and standard requirements of the U.S. Forest Service. Use only mufflers and parts approved by the manufacturer. Any person(s) installing an unapproved muffler, or an unapproved exhaust system part, or modifying an exhaust system in any way that might cause a hazard, is liable for any damage, injury or warranty expense that might be caused by such unapproved installation or modification.

Failure to provide and maintain a spark arrestor may be in violation of the law. If this generator is used on any forest covered, brush covered or grass covered unimproved land, provide a spark arrestor. The vehicle owner or operator must maintain this device in good condition. In the state of California, the preceding is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands.

When installing/replacing the tailpipe or spark arrestor components, verify that the tailpipe has a hole to securely fasten the spark arrestor components (see Figures 2.11 and 2.12). Use only manufacturer supplied hardware. Substitution of parts may cause damage to the screen or a loose fit to the tailpipe.

Figure 2.11 - Spark Arrestor

TAILPIPE P/N 0E0683

SPARK ARRRESTOR

SCREEN P/N 089680

RETAINING SCREW P/N 056892

2.5.2 EXHAUST SYSTEM SAFETY



• Maintain a clearance of at least 3 inches (76 mm) between exhaust system parts and any combustible material (such as wood, felt, cotton, organic fibers or other like material). If the 3-inch (76 mm) clearance cannont be maintained, locate, insulate or shield the exhaust part(s) so that the temperature of any combustible material is not raised more than 117° F (65° C) above the ambient air temperature.

• Extend the exhaust system at least 1 inch (25 mm) past the outer edge of the vehicle. Do not terminate the exhaust system under the vehicle.

• Terminate the exhaust tailpipe such that exhaust gases will not be drawn back into the generator compartment and recirculated.

• If there is any possibility of the tailpipe or muffler being damaged, protect these damage-prone areas by means of a protective device (such as a skid bar).

• Install the generator exhaust system according to safe automotive practices.

• Use enough exhaust system hangers to prevent any part of the system from being dislocated.

• Use exhaust system parts recommended by the manufacturer. Using unapproved exhaust mufflers and exhaust system parts is the responsibility of the person(s) installing such unauthorized parts.

• Do not terminate the exhaust system under any opening, window or vent that can be opened or is not permanently sealed from the vehicle interior.

• Exhaust piping must be large enough to prevent excessive back pressure on the generator engine.

• Never tee the generator engine exhaust pipe into the vehicle engine exhaust piping. This causes excessive back pressure on the generator engine. Also, water from one engine can damage the other engine.

• Plan exhaust system installation carefully. Comply with all applicable codes, standards and regulations.

Figure 2.12 — Spark Arrestor Installation

2.6 ELECTRICAL CONNECTIONS

Be sure to read Section 1.6.

The following general rules apply to electrical connections in a recreational vehicle:

• Qualified electricians who are familiar with applicable codes, standards and regulations should install electrical wiring.

27.4 [1.08"] I.D

• The wiring should comply with codes, standards and regulations. The National Electrical Code (NFPA 70), and state and local codes apply.

• Switches and circuit breakers should be of a type

40 [1.58"

5.5 [7/32"] DRIL BOTTOM SIDE ONL

approved for use in recreational vehicles and must be mounted and installed to prevent damage from road shock.

Section 2 – Installation

Recreational Vehicle Generator

• Wiring must be of adequate size, have approved insulative qualities and be properly supported.

• Conduit and wire openings into the generator compartment (if used) must be vapor-sealed to prevent entry of flammable, explosive or poisonous gases into the vehicle.

2.6.1 ELECTRICAL JUNCTION BOX



Install an approved, square electrical junction box with a blank cover on the interior or exterior wall of the area planned for installation of the generator (NOT on the generator). Route the generator's AC output leads into this junction box through approved flexible conduit. This is the point of first termination for generator AC output leads.

2.6.2 WIRING



• Wiring should be of stranded copper to reduce the chance that vibration may cause breakage.

• Wire gauge size should be large enough to handle at least 115 percent of the installed generator's rated maximum current.

• Neutral conductors must be the same size as other leg wires.

• Route power supply conductors from generator AC output leads (white), (black) and the green ground wire through approved flexible conduit to the electrical junction box on the compartment wall.

If flexible metal conduit is used between the gen-

erator and the compartment junction box, the conduit end that terminates the compartment junction box must be vapor-sealed. Flexible metal conduit is NOT vapor tight along its entire length.

• From the junction box, route power supply wires through approved conduit to either (a) double-pole, double-throw transfer switch, or (b) approved isolation receptacle. Connecting to a transfer switch or isolation receptacle must prevent vehicle electrical circuits from being connected to two different power supplies at the same time (such as generator and dockside power).

• Conductors must be rated 221° F (105° C) or must be of a larger conductor size.

2.6.3 GENERATOR AC CONNECTIONS



Generator AC output leads (BLACK) “hot” and (WHITE) grounded neutral come out of the generator as shown in Figure 2.13. There is also a green lead that connects to ground in the junction box of the recreational vehicle.

Figure 2.13 – Generator AC Output Leads

483.1

REMOTE PANEL CONNECTOR

AC OUTPUT HARNESS

FUEL FILTER

BATTERY

CONNECTIONS

Leads BLACK to WHITE are protected against overload by a 30-amp circuit breaker (CB1). Use this line-to-neutral connection separately to operate 120volt, single-phase, 60 Hertz, AC loads requiring up to 3,600 watts (3.6 kW) of power.

Do NOT connect electrical loads in excess of any



circuit breaker rating or problems will develop with circuit breaker tripping, which causes a loss of AC output. Also, do NOT exceed the generator's rated wattage capacity. Add the watts or amperes of all lighting, appliance, tool and motor loads the generator will operate at one time. This total should be less than the unit's rated wattage/amperage capacity.

2.6.4 CONDUIT



Route the connections between the generator and the junction box through approved, flexible conduit. The following general rules apply:

• Cut wiring to the required length and allow extra wire for junction box connections.

• Carefully prepare conduit ends to prevent sharp edges from cutting through wiring insulation.

• Route conduit so it does not interfere with generator movement.

• If using metallic conduit, vapor seal the end of the conduit where it enters the junction box. Do this because flexible metallic conduit is not vaporproof along its entire length.

Section 2 – Installation

Recreational Vehicle Generator

2.6.5 ISOLATING DIFFERENT POWER



SOURCES

Connections from the junction box must terminate in a double-pole, double-throw transfer switch (Figure

2.14). An alternate method for isolating different power sources is by using an isolating receptacle (Figure 2.15). Whichever method is used, be certain that both power sources are NOT connected at the same time.

Figure 2.14 – Transfer Switch Isolation Method

2.6.6 POWER SUPPLY CORD



The power supply cord must comply with all applicable codes, standards and regulations. It must be large enough to handle the full amperage to which it will be subjected.

GENERAC

QUIETP

R AC

I I

RIAL

CT 40G

R V

E R

V I C

A T

0 . 3

3 .1

2 2

Figure 2.15 – Installation With Isolation Receptacle

QUIETPA

ERED

N E

R A

I N

R I

CT 40G

I N

ERVI

O CA

T O

R :

0.33 3 .1

12.00"

COLOR

)

9099-B

Section 2 – Installation

Recreational Vehicle Generator

2.6.7 GROUND FAULT CIRCUIT



INTERRUPTERS

The National Electrical Code (NFPA 70, 551-7) requires that ground fault circuit interrupters (GFCIs) be installed on all external and some internal electrical receptacles. Contact the dealer for recommendations.

2.7 BATTERY INSTALLATION



2.7.1 RECOMMENDED BATTERY

Install a battery that meets the following requirements:

• The battery must be a 12-volt, automotive type storage battery.

• For prevailing ambient temperatures above 32° F (0° C), use a battery rated 70 amp-hours and capable of delivering 400 cold-cranking amperes.

• For prevailing ambient temperatures below 32° F (0° C), use a battery rated 95 amp-hours and capable of delivering 400 cold-cranking amperes.

NOTE:

If the battery is to be used to power other vehicle accessories, as well as start the generator, a battery with a larger capacity may be needed.

2. Connect the battery cable from the battery post indicated by a NEGATIVE, NEG or (-) to the frame ground connection (Figure 2.16).

3. Connect cables so the connectors are clean and tight.

Figure 2.16 – Connecting Battery Cables

POS

FUEL

NEG

2.7.4 BATTERY COMPARTMENT



Install the generator battery in its own, vented compartment. Place the battery compartment away from any source of heat, sparks or flame.

Provide ventilation openings in the battery compartment. The minimum size of openings should be 2 square inches at the top of the compartment. Mount the battery on a strong, rigid supporting structure, where leaks and spills of battery fluid will not cause damage.



2.7.2 BATTERY CABLES

Using battery cables that are too long or too small in diameter may cause a drop in voltage, which causes starting problems. For the best cold weather starting, the voltage drop between battery terminals and the generator connection point should not exceed 0.12 volts per 100 amperes of cranking current.

These generators are rated at about 100 DC amperes of cranking current.

Select battery cables based on (a) cable length and (b) prevailing ambient temperatures. Generally, the longer the cable and the colder the weather, the larger the cable size must be, as shown in the chart.

CABLE LENGTH in Feet (Meters) CABLE SIZE

0 to 10 (0 to 3) 2* 11 to 15 (3.4 to 4.5) 0 16 to 20 (4.5 to 6) 000

* For warm weather, use No. 2 cable up to 20 feet.

2.7.3 BATTERY CABLE CONNECTIONS



1. Connect the battery cable from the battery post or terminal indicated by a POSITIVE, POS or (+) to the lug on the starter contactor (Figure 2.16).

NOTE:

Check to be sure the battery cable boot for the starter cable has been installed.

2.8 OPTIONAL ACCESSORIES

A plug-in receptacle (Figure 2.17) is provided on the generator set. Use this receptacle to connect an optional remote-mounted start/stop panel to the generator. Installation of such a panel will permit starting and stopping the generator engine from any convenient location inside the vehicle.

Figure 2.17 – Remote Panel Plug-in Receptacle

RAN

YELL

BROW

P/N: 0D

LENGTH (mm

12.0 (305

FUNCTION

GROUND

ENGINE RUN SIGNAL

12 VDC START STOP PRIME

STOP

Section 3 – Post-Installation Start-up Adjustments

Recreational Vehicle Generator

2.8.1 REMOTE START/STOP PANEL



A remote mounted Start/Stop panel (Figure 2.18) is available that allows the user to start and stop the generator engine conveniently from inside the vehicle. The remote panel includes a Start/Stop switch, hourmeter, generator run lamp, a fuel prime switch, and a wire harness. The hourmeter should be used in conjunction with the maintenance operations found in Part I of this manual.

Figure 2.18 – Optional Remote Panel

FUE

3.1 POST INSTALLATION TESTS

The air-cooled generator set was factory tested and adjusted. It should not be required to adjust the unit any further except under special circumstances.

Do not make any unnecessary adjustments.



Factory settings are correct for most applications. When making adjustments, however, be careful to avoid overspeeding the engine.

3.2 BEFORE INITIAL START-UP

Before starting, complete the following:

1. Check the engine crankcase oil level and, if necessary, fill to the dipstick “FULL” mark (crosshatched area) with the recommended oil. Do not fill above the FULL mark.

2. Check the fuel supply. Gas fuel lines must have been properly purged and leak tested in accordance with applicable fuel codes. All fuel shutoff valves in the fuel supply lines must be open.

DANGER

If a liquid propane (LP) gas fuel system has been



installed, it must be properly tested for leaks before operating the system in compliance with ANSI A119.2/NFPA 501C. No leakage is permitted. Be sure that no gasoline fuel vapors enter the vehicle interior.

3.3 INITIAL START

When absolutely certain that the unit has been properly installed and prepared for use, start the engine as follows:

1. Turn off all electrical loads. Do this by setting the generator’s main circuit breakers to their “OFF” (or open) position.

2. Refer to Part I, Section 2.5, “Starting the Generator”, for cranking and starting instructions. The engine may require more cranking for initial starting since the fuel lines have to be primed (use of the primer switch will shorten this time).

3. Let the engine warm up for about five minutes to allow internal temperatures to stabilize.

4. Carefully inspect the engine/generator for fuel, oil and exhaust system leaks. Before proceeding to the next step, correct any leakage immediately.

5. When all tests and adjustments at no-load are completed, apply electrical loads and check for proper operation under load. See Section 3.4. Run the unit at least 30 minutes with loads applied.

6. Turn off all electrical loads by setting the generator’s main circuit breakers to their “OFF” (or open) position.

7. Let the unit run at no-load for a few minutes to stabilize internal engine/generator temperatures. Then, shut down the engine.

NOTE:

The generator set was thoroughly tested and adjusted at the factory before shipping. No additional adjustment should be necessary. Only qualified service technicians who have been trained should perform adjustments outlined in this manual.

3.4 TESTING UNDER LOAD

Apply electrical loads equal to about 75 to 100 percent of the unit's rated wattage/amperage capacity.

Let the unit run at least 30 minutes with load applied. During this part of the test, check that the unit is not running excessively hot and that adequate cooling airflow is available. Do not allow the unit to overheat during prolonged operation.

NOTE:

The generator engine is equipped with a high temperature switch. The switch has normally closed (N.C.) contacts. When the engine temperature is too high, switch contacts close, and the engine shuts down automatically.

THE MANUFACTURER RECOMMENDS THAT THE GENERATOR BE TESTED FOR ADEQUATE COOLING.

Section 3 – Post-installation Start-up Adjustments

3.5 INSTALLATION CHECKLIST

LOCATION AND SUPPORT



❑ Generator is properly located.

❑ Generator is properly supported.

❑ Generator is properly restrained.

GENERATOR COMPARTMENT



❑ Compartment construction is proper.

❑ Holes/Openings are vapor-sealed.

❑ Compartment size is correct.

❑ Compartment is vapor-sealed.

❑ Sound insulation is correct.

❑ Floor cutouts are properly completed.

COOLING AND VENTILATING AIR



❑ Airflow is adequate.

❑ Air inlet opening is correct.

❑ Compensate for restrictions.

❑ Check that installation has been tested.

GASOLINE FUEL SYSTEM



❑ Fuel tank complies with all applicable codes.

❑ Fuel system is properly installed and checked

for leaks.

OPTIONAL LP GAS FUEL SYSTEM



❑ Fuel system is properly installed and checked

for leaks.

❑ Pressure at regulator inlet is correct.

❑ Rated flow of primary regulator is correct.

❑ All parts are properly installed.

❑ Fuel system is properly tested/adjusted.

Recreational Vehicle Generator

EXHAUST SYSTEM



❑ Exhaust system complies with all applicable

codes.

❑ Exhaust system is properly and safely installed.

ELECTRICAL CONNECTIONS



❑ Connections comply with local code requirements

and all National Electrical Codes.

❑ Junction box is properly installed.

❑ Wiring meets all standards.

❑ All connections are correct.

❑ Conduit is properly installed and sealed.

❑ Generator is properly bonded to the vehicle.

BATTERY INSTALLATION



❑ Recommended battery is installed.

❑ Recommended cables are installed.

❑ Cables are clean and tight.

❑ Cables are connected properly.

❑ Proper ventilation is provided.

❑ Terminals are coated with anti-corrosion grease,

and terminal covers are positioned.

OPTIONAL ACCESSORIES



❑ Check that remote start/stop panels (if used) are

installed properly.

❑ Check that hourmeter kit (if used) is installed

properly.

❑ Check that any other options and accessories (if

used) are installed properly.

POST INSTALLATION TESTS



❑ Check that all tests are completed properly.

DATE OF INSTALLATION ____________________________________________________

NAME OF INSTALLER _______________________________________________________

SIGNATURE OF INSTALLER _________________________________________________

Appendix 1 – Notes

Recreational Vehicle Generator

Appendix 2 – Troubleshooting

Recreational Vehicle Generator

TROUBLESHOOTING GUIDE

Problem Cause Correction

The engine will not crank. 1. Fuse blown 1. Replace fuse.

2. Loose, corroded or defective 2. Tighten, clean or replace battery cables as necessary.

3. Defective engine Start/Stop 3. Replace Start/Stop switch. switch

4. Defective starter contactor 4. Replace contactor.

5. Defective starter motor 5. Replace starter motor.

6. Low or defective battery 6. Charge or replace battery.

The engine cranks but 1. Out of fuel 1. Replenish fuel. will not start. 2. Defective fuel pump 2. Replace fuel pump.

3. Open #14 wire from 3. Check connections and. engine control board insulation of #14 wires.

4. Flooded engine 4. Wait 5-10 minutes before trying.

5. Defective spark plug(s) 5. Clean, re-gap or replace plug(s).

6. Fuel line shut-off closed 6. Open fuel line shut-off.

7. Plugged fuel filter 7. Clean or replace fuel filter.

The engine starts hard 1. Air cleaner 1. Check, clean or replace air cleaner. and runs rough. plugged or damaged

2. Defective spark plug(s) 2. Clean, re-gap or replace plug(s).

The engine starts, but shuts 1. Engine oil level low 1. Check oil and add oil as needed. down when the Start/Stop 2. Defective low oil 2. Replace pressure switch. switch is released. pressure switch

3. Defective high temperature 3. Replace temperature switch. switch

4. Defective engine control board 4. Replace control board.

5. Overheated engine 5. Check that the airflow openings are adequate.

The Start/Stop switch is 1. Defective Start/Stop switch 1. Replace switch. set to Stop, but the engine 2. Open/Disconnected #18 wire 2. Reconnect or close wire.

continues to run. between Start/Stop switch and engine control board

3. Open/Disconnected #0 wire 3. Reconnect or close wire. between Start/Stop switch and engine control board

4. Defective engine control board 4. Replace control board.

There is no AC output from 1. Main line circuit breaker open 1. Reset circuit breaker the generator. to ON (or closed).

2. Fault with vehicle circuit 2. Reset and replace if necessary. breaker and/or fuses

3. Transfer switch set to NORMAL 3. Set switch to GENERATOR.

4. Start switch not held long 4. Stop, then restart the engine enough to flash the field (Hold Start switch for at least 2 seconds).

5. Generator internal failure 5. Contact aN Authorized Service Dealer.

SW2

GREEN

NEUTRAL CONNECTION BY CUSTOMER

Appendix 3 — Electrical Data

Recreational Vehicle Generator Electrical Schematic and Wiring Diagram – Drawing No. 0D8063-D

BATTERY

BLK

18A

(START)

SW1

(STOP)

4J1-9

HTO

LOP

0I 17 14 18

REMOTE

PAN E L

CONNECTOR

121

2 33 4

STOP

START

11P

CB1

BLACK

REMOTE PANEL (OPTIONAL)

BCR - BATTERY CHARGE RECTIFIER

CB1 - CIRCUIT BREAKER, 30A

CB3 - CIRCUIT BREAKER, 2.5A CH - CHOKE HEATER (GASOLINE ONLY)

CS - CHOKE SOLENOID

F1 - FUSE, 7.5A

FP - FUEL PUMP-OR-LPG SHUT OFF VALVE

FS - FUEL SOLENOID (GASOLINE ONLY)

GT - TERMINAL, GROUND 4-TAB

HM - METER, HOUR (OPTIONAL)

HTO - SWITCH, HIGH TEMP. OIL (CLOSES ON HIGH TEMP.) IM - IGNITION MAGNETO L1 - LIGHT, RUN (OPTIONAL) LOP - SWITCH, LOW OIL PRESSURE PCB - ENGINE CONTROLLER

R1 - RESISTOR, 1 OHM 25W

SC - STARTER CONTACTOR

SM - STARTER MOTOR

SW1 - SWITCH, START/STOP

SW2 - SWITCH FUEL PRIMER

SP - SPARK PLUG TC - TERMINAL, CONN. 4-TAB

22P

WHITE

RED

14A

PCB

J1-1

J1-2

J1-3

J1-4

J1-5

J1-6 17

J1-7

J1-8

J1-10

J1-11

J1-12

J1-13

J1-14 18

J1-15

BCR

BATTERY CHARGE WINDING

POWER WINDING

22S 11S

ELECTRONIC

VOLTAGE

REGULATOR

CB3

DPE WINDING

FIELD

120V 30A

WHITE

RED

BROWN77YELLOW

BLUE

ORANGE

A41

FUEL

PRIME

LEGEND

(CLOSES ON LOW PRESSURE)

SUPPLIED BY

CUSTOMER

12V

BATTERY

Appendix 3 — Electrical Data

Recreational Vehicle Generator

Electrical Schematic and Wiring Diagram – Drawing No. 0D8063-D

SUPPLIED BY

CUSTOMER

PCB

J1-10 J1-11 J1-12 J1-13 J1-14 J1-15

11S

16 56

J1-2 J1-3 J1-4 J1-5 J1-6 J1-7 J1-8 J1-9

J1-1

18A

CB3

BCR

18A

CONN. 1

PIN#

RED

18A

LOP

CONN. 2

PIN#

14A

HTO

FILTER MTG SCREW

22S

18A

SW2

62A

ELECTRONIC

VOLTAGE

REGULATOR

11P

22P

RED

STAT OR

CLOSEST TO BEARING

FIELD

22S

11S

11P

14A

SW1

11P

BLACK

WHITE

22P

REMOTE

PAN E L

CONNECTOR

14A

CB1

14A

WHITE

GREEN

SP1

IM1

BLACK

NEUTRAL CONNECTION BY CUSTOMER

14A

CUSTOMER

AC CONNECTION

Appendix 4 — Exploded Views and Parts Lists

Recreational Vehicle Generator Enclosure – Drawing No. 0D8352-G

TO CARB

Appendix 4 — Exploded Views and Parts Lists

Recreational Vehicle Generator

Enclosure – Drawing No. 0D8352-G

ITEM PART NO. QTY. DESCRIPTION

1 0D6822 1 TRAY, ENCLOSURE 2 0D6942 1 PANEL, ENCLOSURE SIDE 3 0D6939 1 PANEL, REAR DIVIDER 4 0D6943 1 PANEL, ENCLOSURE ROOF 5 0D6941 1 PANEL, ENCLOSURE BACK 6 0D6940 1 PANEL, FRONT DIVIDER 7 0D6945 1 COMPARTMENT, AIR INTAKE 8 0D6944 1 PANEL, ENCLOSURE DOOR 9 0D8254 1 SHIELD, MUFFLER 10 0C5644 2 SLIDE LATCH, FLUSH 11 0D7513 1 PUMP, FUEL 12 087769 1 FILTER, FUEL 13 0D7613 1 FUEL LINE, FILTER TO PUMP 14 0D7614 1 FUEL LINE, PUMP TO CARB 15 048031C 2 CLAMP HOSE BAND ¼” 16 047411 2 SCREW HHC M6-1.0 X 16 17 022473 2 WASHER FLAT ¼” 18 023484S 1 BUSHING, 1.09” SNAP 19 022097 2 WASHER LOCK M6-1/4” 20 086729 1 CONTACTOR, STARTER 21 0D3700 24 NUT FLANGE M6-1.0 NYLOK 22 022129 2 WASHER LOCK M8-5/16” 23 022259 2 NUT HEX 5/16”-18 24 075763A 2 BOOT BATTERY CABLE 25 0D7293 1 PANEL AIR BOX COVER 26 064113 1 SCREW, M6-1.00 X 20MM WING 27 0C7561 1 BOLT CARR 3/8”-16 X 1” 28 0A4456 1 3/8” SPECIAL L/WASHER 30 049813 2 NUT HEX M6 X 1.0 31 022237 1 WASHER LOCK 3/8” 32 022131 2 WASHER FLAT 3/8-M10”

ITEM PART NO. QTY. DESCRIPTION

33 0C5443 1 BLOCK, TERMINAL BATTERY POST 34 0C7423 1 STUD 3/8”-16 X 2”-1/4” BRASS 35 029451 2.1’ TAPE FOAM 1/8” X ½” 36 074908 4 SCREW HHTT M5-0.8 X 10 37 0D8717 1 CUSTOMER CONNECTION HARNESS 38 0D9020 1 FOAM, AIR OUT COMPARTMENT SIDE 39 0742600144 1 CABLE, STARTER 40 0E0724 1 ASSEMBLY OIL DRAIN 41 0A7215 18 SCREW SW ¼”-20 X 5/8” WITH NYLON

WASHER 42 0742600143 1 CABLE, BATTERY CONNECTION 43 0D8595 1 MOUNT, FUEL FILTER SUPPORT 44 0D8627 2 FOAM, AIR INTAKE COMPARTMENT 45 0D8628 1 FOAM, ROOF AIR OUT COMPARTMENT 46 0D8628A 1 FOAM, BACK COMPARTMENT 47 0D8691 1 FOAM, DOOR PANEL 48 0D7176 4 WASHER SELF LOCKING 1" 49 0A2115 1 WASHER NYLON .250” 50 0D9282 1 HARDWARE CLOTH COMPARTMENT

AIR OUT 51 023484E 1 BUSHING, 0.50” SNAP 52 0F9176 8.5” HOSE, 1/4” ID 53 0E0014 1 BOX, MUFFLER TAIL PIPE 54 0E0017 1 GASKET, MUFFLER TAIL PIPE BOX 55 0C7968 4 NUT HEX JAM 3/8”-16 BRASS 56 0E0393 1 ASSEMBLY, CAP & DIPSTICK 57 0D8981 1 FILTER GASKET 58 029451A 8.75’ FOAM TAPE 1/16” X ½” 59 0D8628B 1 FOAM, FRONT AIR OUT

COMPARTMENT

Appendix 4 — Exploded Views and Parts Lists

Recreational Vehicle Generator Generator – Drawing No. 0D8353-H

Appendix 4 — Exploded Views and Parts Lists

Recreational Vehicle Generator

Generator – Drawing No. 0D8353-H

ITEM PART NO. QTY. DESCRIPTION

1 050322 1 SCREW IHHC 5/16"-24 X 9-3/4" 2 022129 22 WASHER LOCK M8-5/16" 3 049451 1 WASHER FLAT .406" I.D. X 1.62" O.D. 4 0C8096A 1 FAN, 8" CURVE BLADE, 16.5MM I.D. 5 0D8120 4 SCREW IHHC M8-1.25 X 260MM 6 066849 2 SCREW HHTT M5-0.8 X 16 7 066386 1 ASSEMBLY, BRUSH HOLDER 8 0D4217 1 CARRIER, REAR BEARING 9 073159 1 BEARING 10 0D4484H 1 ROTOR 11 0D4430H 1 STATOR 12 0D4216 1 ADAPTOR, ENGINE 13 048614 4 SCREW HHC 5/16"-24 X 3/4" 14 0D2588A 1 GASKET, FRONT DIVIDER 15 022131 4 WASHER FLAT 3/8"-M10 16 027028 4 NUT LOCK HEX 5/16"-18 NYLON INSERT 17 0D6832 1 BRACKET, ENGINE MOUNTING 18 022145 18 WASHER FLAT 5/16" 19 030231 3 SCREW HHC 5/16"-18 X 1-1/2" 20 0C3168 1 5/16" SPECIAL LOCK WASHER 21 022259 10 NUT HEX 5/16"-18 22 0C8565 2 SCREW SHC M8-1.25 X 18MM 23 0D8048 4 VIBRATION MOUNT 24 083512 6 SCREW HHTT M8-1.2 X 16MM 25 0D6831 1 BRACKET, ALTERNATOR MOUNTING 26 029451 2.14' TAPE ELEC. UL FOAM 1/8" X 1/2" 27 0D6918 1 DUCT, ALTERNATOR AIR 28 0D2558 1 GASKET, ALTERNATOR DUCT 29 087680 2 NUT WING M6-1.0 30 0D7530 1 STUD, M6-1.0 OFFSET 31 0D9723 1 ELEMENT, AIR FILTER 32 0D4511 1 PRECLEANER, AIR 33 0D8451 1 WASHER FLAT .281" I.D. X 1.50" O.D. 34 022097 1 WASHER LOCK M6-1/4" 35 0D7440 1 MUFFLER 36 090388 2 SCREW HHTT M6-1.0 X 12MM 37 0D7441 2 BOLT CARR 5/16"-18 X 2" 38 081105 2 NUT FLANG 5/16"-18 LOCK 39 089476 1 GASKET, EXHAUST 41 022531 1 SCREW HHC 5/16"-18 X 1-3/4" 42 0D8981 1 FILTER GASKET RV

819

Appendix 4 — Exploded Views and Parts Lists

Recreational Vehicle Generator Control Panel – Drawing No. 0D8354-E

Appendix 4 — Exploded Views and Parts Lists

Recreational Vehicle Generator

Control Panel – Drawing No. 0D8354-E

ITEM PART NO. QTY. DESCRIPTION

1 0830490 1 REGULATOR VOLTAGE 2 075210A 1 TERMINAL BLOCK 3 092234 1 CONTROLLER P.C.B. 4 065795 1 BATTERY CHARGER RECTIFIER 5 023484F 1 BUSHING SNAP 1" 6 023484R 1 BUSHING SNAP 1-1/4" 7 075234 1 RESISTOR, 1 OHM 25W 8 057159 1 CIRCUIT BREAKER 2.0 AMP (60HZ) 054502 1 CIRCUIT BREAKER 3.0 AMP (50HZ) 9 087798 1 SWITCH S.P.D.T. 10 092113 1 SWITCH S.P.D.T. ON-MOM-ON 11 032300 1 HOLDER FUSE 12 0A9611 1 FUSE 7.5A 13 090145 1 CIRCUIT BREAKER, 30 X 1 (60HZ) 0E2314 1 CIRCUIT BREAKER, 15A 2 POLE (50HZ) 14 0A1658 2 LOCK WASHER SPECIAL 15 075235 2 SCREW HHC M5-0.8 X 30MM 16 047411 2 SCREW HHC M6-1.0 X 16MM 17 049226 5 WASHER LOCK M5 18 051716 1 NUT HEX M5-0.8 19 075476 2 SCREW PPHM M4-0.7 X 16MM 20 022264 2 WASHER LOCK #8-M4 21 051715 4 NUT HEX M4-0.7 22 0A2053 1 SCREW HHC M6-1.0 X 65MM 23 022473 5 WASHER FLAT 1/4" 24 022097 4 WASHER LOCK M6-1/4" 25 049813 4 NUT HEX M6-1.0 26 055440 2 SCREW HHC M5-0.8 X 25MM 27 049815 1 SCREW HHC M5-0.8 X 16MM 28 038750 2 SCREW HHC M6-1.0 X 30MM 29 051714 2 NUT, HEX M3-0.5 30 0D8794 1 PANEL CONTROL 31 025105 2 SCREW RHM #6-32 X 1/4" SIMS 32 028739 2 TIE WRAP UL 4" (NOT SHOWN) 33 0D8308 1 DECAL (NOT SHOWN) 34 0D8418 1 HARNESS (NOT SHOWN) 35 023484S 1 BUSHING, SNAP 1.09" 36 043182 2 WASHER LOCK M3 37 031879 2 WASHER FLAT M3 38 0D6575D 1 DEUTSCH, MOUNTING CLIP 39 0A9973 1 RIVET POP 0.125" LARGE FLANGE

Appendix 4 — Exploded Views and Parts Lists

Recreational Vehicle Generator GN-220 H/SH Engine – Drawing No. 0D8355-S Part 1

2020

Appendix 4 — Exploded Views and Parts Lists

Recreational Vehicle Generator

GN-220 H/SH Engine – Drawing No. 0D8355-S Part 1

ITEM PART NO. QTY. DESCRIPTION

1 0D8433 1 GUARD, FAN 2 0C1069 10 SCREW, HHTT M6-1.0 X 8mm 3 090695F 1 BLOWER HOUSING 4 081810 1 NUT, HEX M16-1.5 5 083312 1 WASHER, M16 CONICAL 6 0D8400 1 ASSEMBLY CHOKE SOLENOID BRACKET 7 0C8917A 1 FLYWHEEL, WITH RING GEAR 8 0C8798A 1 BACKPLATE, ELECTRIC START 9 045756 9 SCREW HHTT M6-1.0 X 10mm 10 082774 1 KEY, WOODRUFF 4 x 19D 11 022129 2 5/16”-M8 LOCK WASHER 12 081990 2 SCREW SHC M8-1.25 X 40mm 13 0D9004A 1 ASSY, STARTER 14 0E7585 1 SPARK PLUG, CHAMPION RC14YC 15 022097 2 LOCKWASHER, ¼”- M6 16 082981 2 TAPTITE, M6-1.0 x 30mm 17 081675 1 ASSEMBLY, IGNITION COIL 19 0D7666A 1 BREATHER TUBE 20 090051 1 GASKET, MANIFOLD/ HEAD 21 080316 2 SCREW HHFC M6-1.0 X 30mm 22 090948 1 INTAKE MANIFOLD 23 078631 1 GASKET CARBURETOR/MANIFOLD 24 0D8332 1 CARBURETOR 25 091846 1 GASKET, CARB/ ADAPTOR 26 0D7558 1 ADAPTOR, CARB 27 078643 2 BOLT, CARB MOUNT M6-1.0 x 75mm 28 0D8372 1 GASKET, CARB TO AIRBOX 29 0C2756 1 ASSEMBLY, GOVERNOR LEVER 30 0D7458 1 ROD, GOVERNOR 31 0C3979 1 SPRING, ANTI LASH 32 085953 1 WASHER, CARB WEAR 33 0D8739 1 ASSEMBLY BRACKET GOVERNOR ADJUST 34 0D8398 1 ROD, CHOKE LINKAGE 35 091638A 1 SPRING, GOVERNOR 36 083512 1 SCREW HHTT M8-1.2 x 16mm 37 082025 1 NUT, M5-0.8 LOCK 38 092984 1 TOP WRAPPER 39 094820 1 PLUG, EXPANSION 40 089739 1 LOWER WRAPPER 41 091848 1 GASKET, OIL PSI PAD 42 0D8778 1 ADAPTER, OIL FILTER 43 0D8803 2 SCREW SHC M6-1.0 X 22mm 44 0A8584 1 SWITCH, OIL- 10 PSI 45 070185B 1 FILTER, OIL 52 075281 1 SWITCH, THERMAL 284F 53 043182 2 WASHER LOCK M3 54 0C4739 2 SCREW PPHM M3-0.5 X 6mm 55 0D9689 1 ELBOW 90D STREET 1/8NPT 56 0A7095 2 RHMS #4-40 X 5/16” SEMS 57 077091 1 COTTER PIN 58 0D8397 1 ROD, CHOKE CONTROL 59 077075 1 BOOT CHOKE SOLENOID PLASTIC 60 0C2824 2 SCREW TAP-R #10-32 X 9/16” 61 0A7094 2 RHMS #4-40 X 1/4” SEMS 62 0D8590 1 ASSEMBLY, BI-METAL/HEATER 63 0D8591 1 SOLENOID, CHOKE

Appendix 4 — Exploded Views and Parts Lists

Recreational Vehicle Generator GN-220 H/SH Engine – Drawing No. 0D8355-S Part 2

242223

Appendix 4 — Exploded Views and Parts Lists

Recreational Vehicle Generator

GN-220 H/SH Engine – Drawing No. 0D8355-S Part 2

ITEM PART NO. QTY. DESCRIPTION

N/A 0E8804 1 LONG BLOCK ASSEMBLY 1 078621 1 CONNECTING ROD ASSEMBLY 2 076389 1 PISTON PIN 3 088411 1 PISTON RING SET 4 0A8897B 1 GEAR COVER ASSEMBLY 5 077168 5 M8 x 56mm HEAD BOLT 6 088057 1 PISTON 7 076390 2 PIN RETAINER RING 8 0E8540A 1 TAPERED CRANKSHAFT ASSEMBLY 9 078658 1 GOVERNOR “R” PIN 10 0F0967 2 WASHER FLAT 1/4, .015 THK 11 089213E 1 CRANKCASE ASSEMBLY 12 0A7637 1 GOVERNOR ARM 13 0E3811 2 OIL SEAL 14 0D1303 1 GOVERNOR GEAR ASSEMBLY 15 078645 1 GOVERNOR GEAR C-RING 16 0A7811 1 GOVERNOR SPOOL 17 072683A 1 1/8” NPT PIPE PLUG 18 0A9878 1 CAMSHAFT ASSEMBLY 19 089096 1 CRANKCASE GASKET 20 088156 1 VALVE STEM SEAL 21 0A8822 1 CYLINDER HEAD GASKET 22 078691 1 OIL PRESSURE RELIEF COVER 23 0A5772 1 OIL PRESSURE SPRING 24 0A5776 1 11/32” BALL 25 074908 1 M5 FORM SCREW 26 078606 4 M6-1.0 x 12mm SCREW 27 076361 1 GOVERNOR GEAR THRUST WASHER 28 0D2414 6 SCREW, HHFC M8-1.25 X 35mm 29 099922 1 SPRING WASHER 30 0C3733 2 VALVE RETAINER 31 0C4390 2 VALVE SPRING 32 084186 2 VALVE SPRING WEAR WASHER 33 083192 1 GEROTER SET 34 0E0057 1 “O” RING 35 078699B 4 SLEEVE, SEAM DWL 36 021705B 1 CYLINDER HEAD ASSEMBLY 37 0C3590 1 EXHAUST VALVE 38 0C3591 1 INTAKE VALVE 39 0D9853A 2 PUSH ROD 40 083235 2 TAPPET 41 080336 1 OIL PICK-UP ASSEMBLY 42 0C8754 1 ROCKER COVER GASKET 43 077161 2 PIVOT BALL STUD 44 077160 2 GN- 191/220 ROCKER ARM 45 076307 2 ROCKER ARM JAM NUT 46 088403 1 PUSH ROD GUIDE PLATE 47 026073A 1 1/4” NPT PIPE PLUG 48 0D1411A 1 ROCKER COVER ASSEMBLY 49 076329 1 PLASTIC OIL FILL PLUG 50 0C3592 4 VALVE SPRING KEEPER 51 049340A 1 BARBED ELBOW 90 1/4” NPT X 3/8” 52 045761A 1 STUD M8-1.25 / 10mm X 30mm

Appendix 5 – Warranty

Recreational Vehicle Generator

CALIFORNIA AND FEDERAL EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The California Air Resources Board (CARB) and the United States Environmental Protection Agency (EPA), together with Generac Power Systems, Inc. (Generac), are pleased to explain the Emission Control System Warranty on your new engine.* New utility, and lawn and garden equipment engines must be designed, built and equipped to meet stringent anti-smog standards for the state of California and the federal government. Generac will warrant the emission control system on your engine for the periods of time listed below provided there has been no abuse, neglect, unapproved modification or improper maintenance of your engine.

Your emission control system may include parts such as the carburetor, ignition and exhaust systems. Generac will repair your engine at no cost to you for diagnosis, replacement parts and labor, should a warrantable condition occur.

MANUFACTURER’S EMISSION CONTROL SYSTEM WARRANTY COVERAGE:

Emissions control systems on 1997 and later model year engines are warranted for two years as hereinafter noted. If, during such warranty period, any emission-related component or system on your engine is found to be defective in materials or workmanship, repairs or replacement will be performed by a Generac Authorized Warranty Service Facility.

PURCHASER’S/OWNER’S WARRANTY RESPONSIBILITIES:

As the engine purchaser/owner, you are responsible for the completion of all required maintenance as listed in your factory supplied Owner’s Manual. For warranty purposes, Generac recommends that you retain all receipts covering maintenance on your engine. However, Generac cannot deny warranty solely because of the lack of receipts or for your failure to ensure the completion of all scheduled maintenance.

As the engine purchaser/owner, you should, however, be aware that Generac may deny any and/or all warranty coverage or responsibility if your engine, or a part/component thereof, has failed due to abuse, neglect, improper maintenance or unapproved modifications, or the use of counterfeit and/or ‘grey market’ parts not made, supplied or approved by Generac.

You are responsible for presenting your engine to a Generac Authorized Warranty Service Facility as soon as a problem occurs. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

Warranty service can be arranged by contacting either your selling dealer or a Generac Authorized Warranty Service Facility. To locate the Generac Authorized Warranty Service Facility nearest you, call our toll-free number:

1-800-333-1322

IMPORTANT NOTE: This warranty statement explains your rights and obligations under the Emission Control System Warranty (ECS Warranty), which is provided to you by Generac pursuant to California and federal law. See also the “Generac Limited Warranties for Generac Power Systems, Inc.,” which is enclosed herewith on a separate sheet, also provided to you by Generac. The ECS Warranty applies only to the emission control system of your new engine. If there is any conflict in terms between the ECS Warranty and the Generac Warranty, the ECS Warranty shall apply except in circumstances where the Generac Warranty may provide a longer warranty period. Both the ECS Warranty and the Generac Warranty describe important rights and obligations with respect to your new engine.

Warranty service can be performed only by a Generac Authorized Warranty Service Facility. When requesting warranty service, evidence must be presented showing the date of the sale to the original purchaser/owner. The purchaser/owner shall be responsible for any expenses or other charges incurred for service calls and/or transportation of the product to/from the inspection or repair facilities. The purchaser/owner also shall be responsible for any and/or all damages or losses incurred while the engine is being transported/shipped for inspection or warranty repairs.

If you have any questions regarding your warranty rights and responsibilities, you should contact Generac at the following address:

ATTENTION WARRANTY DEPARTMENT

GENERAC POWER SYSTEMS, INC.

P.O. BOX 297

WHITEWATER, WI 53190

Part 1

Appendix 5 – Warranty

Recreational Vehicle Generator

EMISSION CONTROL SYSTEM WARRANTY

Emission Control System Warranty (ECS Warranty) for 1997 and later model year engines:

(a) Applicability: This warranty shall apply to 1997 and later model year engines. The ECS Warranty Period shall begin on

the date the new engine or equipment is purchased by/delivered to its original, end-use purchaser/owner and shall continue for 24 consecutive months thereafter.

(b) General Emissions Warranty Coverage: Generac warrants to the original, end-use purchaser/owner of the new engine or

equipment, and to each subsequent purchaser/owner, that each of its engines is ...

(1) Designed, built and equipped so as to conform with all applicable regulations adopted by the EPA and CARB pursuant

to their respective authority, and

(2) Free from defects in materials and workmanship which, at any time during the ECS Warranty Period, may cause a

warranted emissions-related part to fail to be identical in all material respects to the part as described in the engine manufacturer’s application for certification.

(1) Any warranted, emissions-related parts that are not scheduled for replacement as required maintenance in the Owner’s

Manual shall be warranted for the ECS Warranty Period. If any such part fails during the ECS Warranty Period, it shall be repaired or replaced by Generac according to Subsection (4) below. Any such part repaired or replaced under the ECS Warranty shall be warranted for the remainder of the ECS Warranty Period.

(2) Any warranted, emissions-related part that is scheduled only for regular inspection as specified in the Owner’s Manual

shall be warranted for the ECS Warranty Period. A statement in such written instructions to the effect of “repair or replace as necessary” shall not reduce the ECS Warranty Period. Any such part repaired or replaced under the ECS Warranty shall be warranted for the remainder of the ECS Warranty Period.

(3) Any warranted, emissions-related part that is scheduled for replacement as required maintenance in the Owner’s

Manual shall be warranted for the period of time prior to the first scheduled replacement point for that part. If the part fails prior to the first scheduled replacement, the part shall be repaired or replaced by Generac according to Subsection (4) below. Any such emissions-related part repaired or replaced under the ECS Warranty shall be warranted for the remainder of the ECS Warranty Period prior to the first scheduled replacement point for such emissions-related part.

(4) Repair or replacement of any warranted, emissions-related part under this ECS Warranty shall be performed at no

charge to the owner at a Generac Authorized Warranty Service Facility.

(5) When the engine is inspected by a Generac Authorized Warranty Service Facility, the owner shall not be held responsible

for diagnostic costs if the repair is deemed warrantable.

(6) Generac shall be liable for damages to other original engine components or approved modifications proximately caused

by a failure under warranty of any emission-related part covered by the ECS Warranty.

(7) Throughout the ECS Warranty Period, Generac shall maintain a supply of warranted emission-related parts sufficient

to meet the expected demand for such emission-related parts.

(8) Any Generac authorized and approved emission-related replacement part may be used in the performance of any ECS

Warranty maintenance or repairs and will be provided without charge to the purchaser/owner. Such use shall not reduce Generac’s ECS Warranty obligations.

(9) Unapproved, add-on, modified, counterfeit and/or ‘grey market’ parts may not be used to modify or repair a Generac

engine. Such use voids this ECS Warranty and shall be sufficient grounds for disallowing an ECS Warranty claim. Generac shall not be held liable hereunder for failures of any warranted parts of a Generac engine caused by the use of such an unapproved, add-on, modified, counterfeit and/or ‘grey market’ part.

EMISSION RELATED PARTS INCLUDE THE FOLLOWING:

1) Fuel Metering System:

1.1) Gasoline carburetor assembly and its internal components (if so equipped).

a) Fuel filter (if so equipped) b) Carburetor gaskets c) Fuel pump (if so equipped)

1.2) LPG carburetion assembly and its internal components (if so equipped).

a) Fuel controller (if so equipped) b) Mixer and its gaskets (if so equipped) c) Carburetor and its gaskets (if so equipped) d) Primary gas regulator (if so equipped) e) LP liquid vaporizer (if so equipped)

*Generac engine types covered by this warranty statement include the following:

1) Utility

2) Lawn and Garden Equipment

3) Recreational Vehicle (RV) Generator

4) Industrial Mobile (IM) Generator

Part 2

2) Air Induction System including: a) Intake pipe/manifold b) Air cleaner

3) Ignition System including: a) Spark plug b) Ignition module

4) Catalytic Muffler Assembly (if so equipped) including: a) Muffler gasket b) Exhaust manifold

5) Crankcase Breather Assembly including: a) Breather connection tube

Appendix 5 – Warranty

Recreational Vehicle Generator

GENERAC POWER SYSTEMS’ THREE-YEAR LIMITED WARRANTY

FOR GUARDIAN RECREATIONAL VEHICLE GENERATORS

NOTE: ALL UNITS MUST BE INSTALLED BY GENERAC POWER SYSTEMS AUTHORIZED SERVICE FACILITIES. For a period

of 3 (three) years of operation from the date of original sale, Generac Power Systems, Inc. (Generac) will, at its option, repair or replace any part which, upon examination, inspection and testing by Generac or a Generac Authorized Warranty Service Facility, is found to be defective under normal use and service, in accordance with the warranty schedule set forth below. Any equipment that the purchaser/owner claims to be defective must be returned to and examined by the nearest Generac Authorized Warranty Service Facility. All transportation costs under the warranty, including return to the factory, are to be borne and prepaid by the purchaser/owner. This warranty applies only to Generac generators sold and rated for “Recreational Vehicle” (RV) applications, as Generac has defined Recreational Vehicle generator applications. The factory recommends exercising the unit one half-hour every month.

WARRANTY SCHEDULE – COMMERCIAL APPLICATIONS

YEAR ONE – 100% (one hundred percent) coverage on part(s), labor, removal and reinstallation listed:

• Engine – All components

• Alternator – All components

WARRANTY SCHEDULE – CONSUMER/PERSONAL APPLICATIONS

YEARS ONE AND TWO – 100% (one hundred percent) coverage on part(s), labor, removal and reinstallation listed:

• Engine – All components

• Alternator – All components YEAR THREE – 100% (one hundred percent) only on selected part(s) and labor listed [Any labor and part(s) not listed, and removal

• Rotor, Stator, Computer Control Board (part numbers 0A6060 and 0A3369) and inverter, (if applicable with regard to the generator)

Cylinder Block, Cylinder Head, Crankshaft, Piston(s), Valve, Valve Lifter(s), Intake and Exhaust Manifolds

Generac RV generators manufactured prior to December 31, 1997, DO NOT have a transferable warranty. Generac RV generators manufactured after January 1, 1998, have a transferable warranty to the second owner ONLY for the remainder of the three-year limited warranty. Proof-of-purchase is required and must be presented to a Generac Authorized Warranty Service Facility prior to the performance of any warranty service.

All warranty expense allowances are subject to the conditions defined in Guardian’s Warranty Policies and Procedures Guide.

• Generac Guardian generators that utilize non-Generac replacement parts.

• Costs of normal maintenance, adjustments, installation and start-up.

• Repairs or diagnostics performed by individuals other than Guardian/Generac authorized dealers not authorized in writing by Generac Power Systems.

• Failures caused by any contaminated fuels, oils, coolants or lack of proper fluid amounts.

• Failures due, but not limited, to normal wear and tear, accident, misuse, abuse, negligence or improper installation. As with all mechanical devices, the Generac engines need periodic part(s) service and replacement to perform well. This warranty will not cover repair when normal use has exhausted the life of a part(s) or engine.

• Failures caused by any external cause or act of God, such as collision, theft, vandalism, riot or wars, nuclear holocaust, fire, freezing, lightning, earthquake, windstorm, hail, volcanic eruption, water or flood, tornado or hurricane.

• Damage related to rodent and/or insect infestation.

• Products that are modified or altered in a manner not authorized by Generac in writing.

• Any incidental, consequential or indirect damages caused by defects in materials or workmanship, or any delay in repair or replacement of the defective part(s).

• Failure due to misapplication.

• Telephone, cellular phone, facsimile, internet access or other communication expenses.

• Living or travel expenses of person(s) performing service, except as specifically included within the terms of a specific unit warranty period.

• Expenses related to "customer instruction" or troubleshooting where no manufacturing defect is found.

• Rental equipment used while warranty repairs are being performed.

• Overnight freight costs for replacement part(s).

• Overtime labor.

• Starting batteries, fuses, light bulbs and engine fluids.

THIS WARRANTY IS IN PLACE OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED. SPECIFICALLY, GENERAC MAKES NO OTHER WARRANTIES AS TO THE MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

GENERAC'S ONLY LIABILITY SHALL BE THE REPAIR OR REPLACEMENT OF PART(S) AS STATED ABOVE. IN NO EVENT SHALL GENERAC BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, EVEN IF SUCH DAMAGES ARE A DIRECT RESULT OF GENERAC'S NEGLIGENCE. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights. You also have other rights from state to state.

Part No. 0D8351 Revision R (02/22/06) Printed in U.S.A.

and reinstallation are the owner’s responsibility]:

THIS WARRANTY SHALL NOT APPLY TO THE FOLLOWING:

GENERAC® POWER SYSTEMS, INC.

P.O. BOX 297 • WHITEWATER, WI 53190

Revision 02.05

Generac Power Systems 004700-00 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual