Instruction manual
1. Scope of delivery 2. Required arrangements 4. Wall mount options
3.a
Adjust wall
plate vertically
2.b
Loosen lower
bolted assembly
3.b
Anchor holes drilling (6x)
diameter
-6 mm steel-anchor-bolt
-8 mm universal frame fixing set
2.a
Check if all the componets are there and o.k.
2.1 - Screws, safety nuts and washers (in a PE-bag)
2.2 - Adaptor plate (in air cushion)
2.3 - Wall mount bracket
2.c
Gather U-bracket from wall bracket
3. Wall bracket fastening
A concrete wall - e.g.: steel-anchor-bolt M 6 x 65 mm
- drill and blow out hole, place anchor, wall bracket and washer,
tighten hexnut
B perforated bricks - e.g.: unsiversal frame fixing set
B 8 x 80 mm
- drill, countersink and blow out hole, place anchor and bracket,
fix hexagon head wood screw
C injection-molded-anchor
- without sieve bushing for concrete wall
- with sieve bushing for perforated bricks /
- optional with threaded bolt M6 or threaded bushing M6
Advantages: fixing without pressure, enables repeated mounting,
Advantages: capable for diverse wall materials
Advantages: (please notice instructions of anchor manufacturers).
S360-444B GENELEC Wall Mount for GENELEC S360, 8260, 8x5x
WALL MOUNT BRACKET
ADAPTOR PLATE
for:
GENELEC 8260A
GENELEC 8x5x
(enables
horizontal
and
vertical
position
of the 8351)
- Not included! -
U-bracket mounting adaptor
for
GENELEC S360
S360-424B
K&M 24468-000-56
- For GENELEC 8260A, 8351A, 8250A, 8050A (with included adaptor plate)
- For GENELEC S360 (S360-424B U-bracket mounting adapter needed!)
- Check for damage prior to and after use. Damaged mounts my not be used again.
- Not suitable for outdoors or moist rooms.
- Observe the local mounting regulations (they may deviate from the examples presented here).
- Only mount on suitable walls with the corresponding assembly material (not included in the delivery).
- Examples - see Point 4.A/B/C. Observe the placement instructions provided by the anchor
- manufacturer.
- Not suitable are fragile walls. Beware of power supply lines and water conduits. In case ask an expert.
- Only use trained technicians to assemble the system.
- Ensure that the screws are tight and load-bearing, in particular as regards the setting of the
- loudspeaker angle.
- Inspect bolted assemblies periodically
- The placement of the loudspeakers requires two physically fit qualified technicians.
- Careful and attentive handling is required when adjusting the stand - due to the possibility of pinching
- or wedging your hand.
- External influences such as bumping into the loudspeakers, brushing into the loudspeakers, things
- thrown at the loudspeaker, wind etc. represent a risk and must be avoided. Measures: Compliance
- with safety distances, keeping unauthorized persons at a distance, if needed put safety cordons.
- The instructions provide directions to all of the important setup
- and handling steps.We recommend,you keep these
- instructions for future reference.
Instruction manual 5. Installation
6. Settings
7. Dimensions Safety instructions
5.b
Bolt the monitor
to adaptor plate.
Use four screws
M6 x 14 mm
with washers
For horizontally
mounting of the
GENELEC 8351
turn the adaptor
plate
5.a
Bolt the U-bracket
to the adaptor plate.
Use three safety nuts
M6 with washers.
6.a
Continuously adjustable
up to 30°, by fixing the
upper bolted assembly
7.a
hole pattern:
127 x 70 mm - M6
&
VESA 100 x 100 - M4/5
7.b
Weight: 1.8 kg
6.b
Pivoting attachment
around vertical axis
5.c
Replace swivel joint (with mounted monitor)
into wall bracket
GENELEC Oy
Olvitie 5, Fin-74100 Iisalmi, www.genelec.com
24478-018-55 Rev.02 03-80-362-00 10/18
S360-444B GENELEC Wall Mount for GENELEC S360, 8260, 8x5x
5.d
Secure swivel joint
to the wall bracket
by tightening lower
bolted assembly
Tightening
torques
10 Nm
Tightening
torques
11 Nm
Tightening
torques
9 Nm
Loading...