Kit Contents
The following hardware should be
included with this rack adapter kit:
1 pcs. Rack mount chassis unit with
cable and connectors in place,
1 pcs. Speaker cable adapter,
4 pcs. 4x12 mm screws.
The bolts and nuts for attaching the rack
adapter into an equipment rack are not
included in this kit.
Cables to go between the amplifier and
speaker are not included in this kit. To
complete the installation, one of the
following cable kits is needed:
Order code Length
1039-203 2 meters
1039-204 5 meters
1039-205 10 meters
1039-206 15 meters
1039-207 20 meters
Instructions
Place the speaker on a flat surface.
Remove the amplifier from the rear of
the speaker cabinet by loosening the
six M4 screws at the edge of the longer
sides. Take special care not to stress the
speaker cables that connects the
amplifier and speaker cabinet. DisconÂnect the speaker cables from the
amplifier.
Place the amplifier and the rack adapter
side by side on a flat surface.
Connect the rack adapter cables (see
fig 1. above) to the amplifier board.
Rack Adapter - Option 11 (1038-421)
for 1038A
Assembly Manual
J704 Speaker Output Connector
B-
B+
CLIP LED
J4 Speaker Output Connector
T+
M+
B+
J101
1
10
1
10
HF & MF MAIN BOARD LF MAIN BOARD
2
1
Fig. 1. Connecting the rack adapter cables on the amplifier
1 Treble and Midrange output connector (J4 Speaker Output Connector, 9
wires)
2 Bass output connector (J704 Speaker Output Connector, 5 wires)
Genelec Document D0024R001C
Copyright Genelec Oy 3/2003
All data subject to change without prior notice
Genelec Oy, Olvitie 5
FIN - 74100 IISALMI, FINLAND
Phone: +358 - 17 - 83881
Telefax: +358 - 17 - 812267
Web: http://www.genelec.com
E-mail: genelec@genelec.com
Dimensions
WH D
Rack mount chassis (mm) 480 530 113 *
(inches) 187/8207/847/
16
Speaker cable adapter (mm) 118 67 57
(inches) 45/825/821/
4
* Without Speakon connecting cable.
Cable connectors require additional
100 mm (4 inches) of space behind the
amplifier
1
3
2
4
5
1
3
2
4
Fig. 3. Installing the speaker cable adapter
1 Speaker cable connector
2 Speaker cable adapter
3 4 x 12 mm screw
4 Speakon 8- and 4-pole cables
(not included in the kit)
Fig. 2. Mounting the amplifier into the
rack adapter chassis
1 M4 screw
2 Amplifier unit
3 Rack adapter cable connector
4 Rack adapter chassis
5 Speakon 8- and 4-pole cables
(not included in the kit)
Place the amplifier on the rack adapter
chassis and fix it with six M4 screws
(see fig 2.). Ensure that the rack adapter
cables do not tighten or press against
any amplifier components.
Connect the Speakon cables to the rack
adapter (see fig. 2.). Push the connector
in and turn it clockwise until the
retaining clip clicks.
The rack adapter can now be mounted
into a standard 19 inch rack. The
adapter chassis height is 12 U, but a
well ventilated free space of at least 1 U
(4,45 cm) is required above and below
to ensure adequate cooling, making the
total space requirement of the assembly
14 U. Please notice that Speakon cable
connectors require additional 100 mm
(4 inches) of space behind the
amplifier.
Attach the speaker cable adapter to the
speaker box with four 4 x 12 mm screws
(see fig. 3.). Connect the speaker cables
and the Speakon cables to the adapter.
Place the speaker into its recess. Now
the system is ready for operation.
Loading...