Genelec HT315A-400 Installation Manual

The followi ng har dware should be

included with this rack adapter kit:

• 1 pcs. Rack mount chassis unit

with cable and connectors in place

• 1 pcs. Speaker cable adapter

• 4 pcs. 4x12 mm screws.

The bolts and nuts for attaching the

rack adapter into an equipment rack are

not included in this kit.

Cables to go between the amplifier and

speaker are not included in this kit. To

complete the installation, one of the fol-

lowing cable kit is needed:

Order code Length

1039-203 2 meters

1039-204 5 meters

1039-205 10 meters

1039-206 15 meters

1039-207 20 meters

Installation

Place the speaker on a flat surface.

Remove the amplifier from the rear of

the speaker cabinet by loosening the

six M4 screws at the edge of the longer

sides. Take special care not to stress the

speaker cables that connect the amplifier

and speaker cabinet. Disconnect the

speaker cable from the J2 connector on

the remote control card (see Fig 1).

Place the amplifier and the rack adapter

side by side on a flat surface.

Connect the rack adapter cable (see Fig

1 above) to the J2 connector.

Place the amplifier on the rack adapter

chassis and fix it with six M4 screws

(see fig 2 overleaf). Ensure that the rack

adapter cables do not tighten or press

against any amplifier components.

Connect the Speakon cables to the rack

adapter (see fig. 2). Push the connector

in and turn it clockwise until the retaining

clip clicks.

The rack adapter can now be mounted

into a standard 19 inch rack. The adapter

chassis height is 12 U, but a well ven-

tilated free space of at least 1 U (4,45

cm) is required above and below to

ensure adequate cooling, making the

total space requirement of the assembly

14 U. Please notice that Speakon cable

connectors require additional 100 mm (4

inches) of space behind the amplifier.

Attach the speaker cable adapter to the

speaker box with four 4 x 12 mm screws

(see fig. 3 overleaf). Connect the speaker

cables and the Speakon cables to the

adapter.

Place the speaker into its recess. Now

the system is ready for operation.

Option 11 (HT315A-400)
HT315A Rack Adapter

Installation Manual

Kit Contents

Fig. 1. Connecting the rack adapter cable to the J2 connector on the remote control card

BASS MAIN BOARD

MAIN BOARD

1

10

J2

4

3

2

1

5

Genelec Documen t D0099R005. Copyright Genelec Oy 9. 2006. All data subject to change without prior notice

Inter national e nquiries:

Genele c, Olvitie 5

FIN-74 100, Iisal mi, Finlan d

Phone [phone]

Fax [phone]

Email genelec@g enelec.com

In the U.S. please c ontact:

Genele c, Inc., 7 Tech Ci rcle

Natick, MA 01760 , U.S.A.

Phone [phone]

Fax [phone]

Email genelec.u [e-mail]

www.genelec.com

Option 11 (HT315A-400)
HT315A Rack Adapter

Installation Manual

Dimensions

W H D

Rack mount chassis

(mm) 480 530 113*

(inches) 187/8 207/8 47/16*

Speaker cable adapter

(mm) 118 67 57

(inches) 45/8 25/8 21/

4

* Without Speakon connecting cable. Cable

connectors require additional 100 mm (4

inches) of space behind the amplifier

Fig. 2. Mounting the amplifier into
the rack adapter chassis

1 M4 screw
2 Amplifier unit
3 Rack adapter cable connector
4 Rack adapter chassis
5 Speakon 8- and 4-pole cables
(not included in the kit)

Fig. 3. Installing the speaker cable adapter

1 Speaker cable connector
2 Speaker cable adapter
3 4 x 12 mm screw
4 Speakon 8- and 4-pole cables
(not included in the kit)

In Sweden please contact

Genelec Sverige

Ellipsvägen 10B

P.O. Box 5521, S-141 05 Huddinge

Phone [phone]

Fax [phone]

Email info@genelec .com

In Chi na please contact:

Beijin g Genelec Audio Co. Ltd.

Jianwa i SOHO, Tower 12, R oom 2306

39 Eas t 3rd Ring Road

Chaoyang District

Beijin g 100022, China

Phone [phone], Fax [phone]

HT315A SPEAKER CONNECTOR

PIN NUMBER SIGNALS

1 +

T+

1 -

T-

2 +

M+

2 -

M-

3 +

B+

3 -

N/C

4 +

B-

4 -

N/C

HT315A LED CONNECTOR

PIN NUMBER SIGNALS

1 +

CLIP LED

1 -

N/C

2 +

POWER LED

2 -

LED GND

Connector wiring