T-311 11Mb High Gain Smart Ethernet Client User’s Guide
y
r
y
r
r
p
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, ma
cause harmful interference to radio communications. However, there is no guarantee that int erference
will not occur in a particular installation. If this equipment does cause harmful interference to radio o
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept an
interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible fo
compliance could void the user's authority to operate this equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
This transmitter must not be co-located or operating in conjunction with any other antenna o
transmitter.
Gemtek systems declares that T-311 ( FCC ID: MXF-A930923B ) is limited in CH1~CH11 for 2.4 GHz by
ecified firmware controlled in U.S.A.
s
Gemtek Systems Page 3
T-311 11Mb High Gain Smart Ethernet Client User’s Guide
1. Before You Start
1.1 Notice
Gemtek Systems, Inc. reserves the right to change specifications without prior notice. While the
information in this manual has been compiled with great care, it may not be deemed an assurance of
product characteristics. Gemtek Systems, Inc. shall be liable only to the degree specified in the terms
of sale and delivery.
The reproduction and distribution of the documentation and sof t ware su pplied wit h this pro duct and the
use of its contents is subject to written authorization from Gemtek Systems, Inc.
1.2 Trademarks
The product described in this book is a licensed product of Gemtek Systems, Inc.
Microsoft, Windows 95, Windows 98, Windows Millennium Edition, Windows NT, Windows 2000,
Windows XP, and MS-DOS are registered trademarks of the Microsoft Corporation.
All other brand and product names are trademarks or registered trademarks of their respective holders.
1.3 National Radio Regulations
Please note:
The usage of wireless network components is subject to national and or regional
regulations and laws.
Administrator must ensure that they select the correct radio settings according to
their regulatory domain. Refer to the regulatory domains chapter in the appendix
to get more information on regulatory domains. Please check the regulations
valid for your country and set the parameters concerning frequen cy, channel, and
output power to the permitted values!
Channel and output power settings may be modified by experienced service
person only!
Gemtek Systems Page 4
T-311 11Mb High Gain Smart Ethernet Client User’s Guide
The default channel numbers for this product, T-311 High Gain Smart Ethernet
Client are only available from 1~11.
Gemtek Systems Page 5
T-311 11Mb High Gain Smart Ethernet Client User’s Guide
2. Table of Contents
BEFORE YOU START....................................................................................................... 4
T-311 11Mb High Gain Smart Ethernet Client User’s Guide
3. About this Guide
3.1 Purpose
This document provides information and procedures on hardware installation, setup,
configuration, and management of the Gemtek Systems High Gain Smart Ethernet Client
T-311.
3.2 Prerequisite Skills and Knowledge
To use this document effectively, you should have a working knowledge of Local Area
Networking (LAN) concepts and wireless Internet access infrastructures. In addition, you
should be familiar with the following:
Hardware installers should have a working knowledge of basic electronics and
mechanical assembly, and should understand related local building codes.
Network administrators should have a solid understanding of software installation
procedures for network operating systems under Microsoft Windows 95, 98, Millennium
Edition, 2000, NT, and Windows XP and general networking operations and
troubleshooting knowledge.
3.3 Conventions Used in this Document
The following typographic conventions and symbols are used throughout this document:
Very important information. Failure to observe this may result in damage!
Important information that should be observed.
Gemtek Systems Page 7
T-311 11Mb High Gain Smart Ethernet Client User’s Guide
Additional information that may be helpful but which is not required.
Bold
Code
<value> Placeholder for certain values, e.g. user inputs
[value] Comment s or hints
Menu commands, buttons and input fields are displayed in bold
File names, directory names, form names, and system-generated output such as
error messages are displayed in constant-width type
3.4 Help us to Improve this Document!
If you should encounter mistakes in this document or want to provide comments to improve the
manual please send e-mail directly to: support@gemtek-systems.com
3.5 Gemtek Systems Technical Support
If you encounter problems when installing or using this product, please consult the Gemtek
Systems website at
http://www.gemtek-systems.com
for
The latest software, user documentation and product updates.
Frequently Asked Questions (FAQ).
Direct contact to the Gemtek Systems support centers.
Gemtek Systems Page 8
T-311 11Mb High Gain Smart Ethernet Client User’s Guide
4. Introduction
Thank you for choosing the Gemtek Systems T-311 11Mb High Gain Smart Ethernet Client.
This manual will assist you with the installation procedure.
4.1 Overview
T-311 allows for one Ethernet-enable device (e.g., Windows/MAC/Linux/UNIX Desktop PC or
laptop) to be instantly connected to an existing 802.11b wireless network. Taking full
advantage of the integrated Web server capability, T-311 is performed through a simple Web
browser user interface for easy configuration.
Besides laptop or desktop environment, T-311 is also the ideal solution to make other network
device such as network printer or camera becomes a wireless station.
4.2 Scope of Delivery
Please ensure that the package is complete before beginning with the installation. The
package should include the following components:
T-311 11Mbp s High Gain Smart Ethernet Client
Dual purposes cable USB/Ethernet with movable SR.
Universal Sucking Disk (USD)
CD (includes user’s manual and quick guide)
Warranty Card
Gemtek Systems Page 9
T-311 11Mb High Gain Smart Ethernet Client User’s Guide
4.3 The Usage of Antenna Housing
When lift the antenna lid, it will be locked/lodged in 45 degrees and 90 degrees (See
pictures A and B).
Please do not lifted the antenna over 90 degrees (See Picture C), otherwise it will
cause damage to antenna.
The antenna housing can rotate up to 135 degrees clockwise/counter-clockwise (See
pictures D~G). It will be locked /lodged in every increment of 45 degrees in position.
Gemtek Systems Page 10
T-311 11Mb High Gain Smart Ethernet Client User’s Guide
4.4 The Usage of Universal Sucking Disk (U.S.D)
1. To pull and rotate USD’s shaft into 90 degrees, then, press it against the surface
to make exhausted its air out. (See pictures A&B )
A
B
2.
Return shaft into original position on USD. (See picture C)
C
Gemtek Systems Page 11
T-311 11Mb High Gain Smart Ethernet Client User’s Guide
3. To Grasp and lift the salient part of the suction cap to allow ventilated. So, USD
can be easily torn off. (See pictures D&E )
D
E
4. Besides the suction cap, the USD kit also equips with magnet and a metal plate to adhere
on the surface. It simply tears off sticker on the back of metal plate and places USD unit on it.
(See picture F)
F
Gemtek Systems Page 12
Loading...
+ 24 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.