GemTek Technology A910910AB Users Manual
Gemtek Technology Co., Ltd.
WX-5520A
Dual Band WLAN Access Point
User's Manual
Oct. 15, 2002 (Draft 1.0)
WX-5520A Dual Band Access Point
CONTENTS
Introduction ............................................................................2
Hardware Installation ............................................................................. 4
WX-5520A AP Default Settings ...………………………………………..5
Web Management Settings …………………………………………6
Start - Up & Log in ……………………………………………………….6
Main Page …………………………………………………………………7
Setup …………...………………………………………………………….8
Password…………. … ..……………………………………………………9
Firmware Upgrade ………………………………………………………..10
Security …………………………………………………………………11
Access Control……….. …………………………………………………..12
Advance Setup …………………………………………………13
About ………………………………………………………………………14
Troubleshooting ……………………………………………………………15
Technical Specifications ……………………………………………………17
Federal Communication Commission Interference Statement …………19
R&TTE Compliance Statement …………………………………………….… .20
Wireless Broadband Anywhere
1
WX-5520A Dual Band Access Point
Introduction
Thank you for purchasing your WX-5520A Dual Band Wireless Access Point.
This user guide will assist you with the installation procedure.
The package you have received should contain the following items:
• WX-5520A Dual Band Wireless AP
• User Guide
• Power Supply / Cord
• Ethernet Cable
Note: if anything is missing, please contact your vendor
Wireless Broadband Anywhere
2
WX-5520A Dual Band Access Point
Safety Notification
Your Wireless AP should be placed in a safe and secure location. To ensure proper
operation, please keep the unit away from water and other damaging elements.
§ Please read the user manual thoroughly before you install the device.
§ The device should only be repaired by authorized and qualified personnel.
§ Please do not try to open or repair the device yourself.
§ Do not place the device in a damp or humid location, i.e. a bathroom.
§ The device should be placed in a sheltered and non-slip location within a temperature
range of +5 to +40 Celsius degree.
§ Please do not expose the device to direct sunlight or other heat sources. The housing
and electronic components may be damaged by direct sunlight or heat sources.
Wireless Broadband Anywhere
3
WX-5520A Dual Band Access Point
Hardware Installation
Front Panel
The front panel provides LED’s for device status. Refer to the following
table for the meaning of each feature.
LED STATUS Description
Power Off No Power
On Power on
Status Blink 1. Power up 2. firmware upgrade
Off no Ethernet link detected
Ethernet Green On 10/100Mbps Fast Ethernet link detected. No activity.
Green Blink Indicates data traffic on the 10/100 Mbps LAN
11a Blink Indicates the device is linking or active data through wireless links
11b Blink Indicates the device is linking or active data through wireless links
Rear Panel
The rear panel features 1 LAN port and Factory Reset button. Refer to the
following table for the meaning of each feature.
Power
(DC 5v)
Reset Reset the configuration to default settings.
LAN The RJ-45 Ethernet ports used to connect your PC, hub, switch or
Used to connect to the power outlet. Only use the power adapter
provided with the device. Use of an unauthorized power adapter
may cause damage to your device and violate your warranty.
There are two ways to Reset to factory defaults of the Access Point.
Briefly press the Reset Button for approximately ten seconds, or use
the setup tab of the Web-Based Management Utility.
Ethernet network.
Wireless Broadband Anywhere
4
WX-5520A Dual Band Access Point
WX-5520A AP Default Settings
The default settings are shown following.
User Name admin
Password 1234
AP Router IP Address 192.168.5.1
AP Router Subnet Mask 255.255.255.0
RF ESSID Wireless
11a RF Channel 52
11b RF Channel 6
RF Roaming Enabled
Encryption Disabled
DHCP client Disabled
Wireless Broadband Anywhere
5
WX-5520A Dual Band Access Point
Web Management Settings
TURN ON POWER SUPPLY
Quick power cycle can caused system corruption. When power on, be careful not to shut
down in about 5 seconds, because data is writing to the flash.
START -UP & LOG IN
In order to configure the WX-5520A Wireless AP, please use your web browser
(Microsoft Internet Explorer or Netscape) and manually input 192.168.5.1 into the address
box (as shown below) and press Enter key.
In order to configure the WX-5520A Wireless AP, please input the user-name into the
User Name box. Enter the password into the Password box and press the OK button. The
default User Name is admin, and the default password is 1234.
Once you have logged-in as administrator, it is a good idea to change the
administrator password to ensure a secure connection to the Wireless AP.
Wireless Broadband Anywhere
6
Loading...