GE Monogram ZISW360DM User Manual

Monogram.

™

For answers to your Monogram,® GE Profile™or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center®service, 800.626.2000.

R

Listed by
Underwriters
Laboratories

Specification Revised 2/02

ZISW360DM - GE Monogram 36" Built-In Refrigerator with Dispenser and

Water Filter

35-1/2

7"

5"

Electrical
Area

84 1/2" max

83 1/2" min

Finished
Opening

74" From Floor

to Bottom

of Electrical

24"

5"

5"

3 1/2"

Water Supply

3 1/2"

36" Models 12"

Water And Electrical Locations

The opening must be prepared with the electrical and water
supply located as shown.

The cutout depth must be 24".

Designed for industry standard flush installation. The
refrigerator will project forward, slightly beyond adjacent
cabinetry, depending on your installation.

The cutout depth beneath a soffit:

When installed beneath a soffit, the soffit cannot exceed the
24” installation depth shown. The top case trim overlaps the
bottom of the soffit.

Frameless cabinets:

The case trim overlaps cabinets at the top and sides.
Therefore, frameless cabinets may require filler strips to
prevent interference with cabinet door swing. The opening
must allow for filler strips.

Additional Specifications

• A 115 volt 60Hz., 15 or 20 amp power supply is required. An
individual properly grounded branch circuit or circuit breaker
is recommended. Install a properly grounded 3-prong electrical
receptacle recessed into the back wall. Electrical must be
located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.

• Water line can enter the opening through the floor or back
wall. The water line should be 1/4" O.D. copper tubing between
the cold water line and
water connection location, long enough to extend
to the front of the refrigerator. Installation of an easily
accessible shut off valve in the water line is recommended.

THE INSTALLATION SPACE

Product Clearances

These refrigerators are equipped with a 2 position door
stop. The factory set 130° door swing can be adjusted
to 90° if clearance to adjacent cabinets or walls
is restricted.

15"

13"

23-7/8"
Behind
Frame

20-5/8

Allow minimum clearances for freezer door and
fresh food door for a full 130° door swing and to
allow for pan removal.

4" minimum clearance is required when door
swing is adjusted to 90°. If the 90° door stop
position is used, pan access is maintained, but
pan removal is restricted.

*84" From
Floor to
Top Frame

36"

Frame to Frame

35"

Case Width

*83-1/2"

at

Rear

* Shipping height.
The refrigerator
can be adjusted to
fit into a cutout that
is 83-1/2” min. to
84-1/2” max. height
Note that the top
case trim at the
front is 1/2” higher
and will overlap
upper cabinetry or
soffit. Use leveling
legs and wheels for
height adjustment.

As an ENERGY STAR® Partner,

GE has determined that this product

meets the ENERGY STAR®

guidelines for energy efficiency.

Specification Revised 2/02

Monogram.

™

For answers to your Monogram,® GE Profile™or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center®service, 800.626.2000.

R

Listed by
Underwriters
Laboratories

ZISW360DM - GE Monogram 36" Built-In Refrigerator with Dispenser and

Water Filter

1/4" FRAMED PANEL DIMENSIONS

If you choose to install framed panels, they must be cut to
the dimensions shown. The panels will slide into the frame
on the door and grille.

Non-Dispenser Models

If the custom panel is less than 1/4" thick and it fits loosely in
the door frame it can be backed up with
a piece of filler material or foam tape to improve
the fit.

1/4"

Panel

Door

5/16"

Trim

Reveal

IMPORTANT NOTE: Maximum weight for fresh food panel is
50 pounds and 30 pounds for freezer panel.

IMPORTANT NOTE – Dispenser Models

The refrigerator is supplied with two dispenser trims, one for
framed panels and one for overlay panels.

• If the panel is less than 0.250" thick a noticeable gap may be
created around the dispenser trim. Foam tape may be applied
on the door to improve the fit.

• If the panel is more than 0.250" thick, the dispenser trim
cannot be secured to the door.

Fresh Food

Panel

Freezer

Panel

18-9/16

14-9/16

17-13/16

3-1/8

33-7/8

9

Grille Panel

68-3/8

Dispenser

Cutout

9-5/8"

Dispenser Cutout

15-3/8"

The framed panel must be 1/4"
nominal thickness to fit the
dispenser trim.

SIDE PANELS

Side panels must be used
whenever the sides of the
refrigerator will be exposed.
The 1/4" side panels will slip
into the side case trim. Order
the side panels from the
cabinet manufacturer.

* Depending on
installation height.

*84"

2-9/16"

24"

*3" to 4"

As an ENERGY STAR® Partner,

GE has determined that this product

meets the ENERGY STAR®

guidelines for energy efficiency.