GE Monogram ZIS480NX User Manual
ZIS480NX
*84" From
Floor to
Top Frame
48"
Frame to Frame
47"
Case Width
*83-1/2"
at
Rear
25-3/4"
27-3/4"
including
handle
23-7/8"
Behind
Frame
90° Door Swing
4" Min.
to Wall
28-5/8"
20"
130° Door Swing
15"
*Finished Width
6"
5"
Electrical
Area
84-1/2" max
83-1/2" min
Finished
Opening
75" From Floor
to Bottom
of Electrical
Area
24"
5"
5"
3-1/2"
Water Supply
3-1/2"
36" Models 12"
42" Models 18"
48" Models 20"
35-1/2" for 36" models
41-1/2" for 42" models
47-1/2" for 48" models
GE Monogram® 48" Built-In Side-by-Side Refrigerator with Automatic
Icemaker and Water Filter
Dimensions and Installation Information (in inches)
The Installation Space
Product Clearances
These refrigerators are equipped with a 2 position door stop.
The factory set 130° door swing can be adjusted to 90° if
clearance to adjacent cabinets or walls is restricted.
Allow minimum clearances for freezer door and fresh food
door for a full 130° door swing and to allow for pan removal.
4" minimum clearance is required when door swing is
adjusted to 90°. If the 90° door stop position is used, pan
access is maintained, but pan removal is restricted.
Installation Information: Before installing, consult
installation instructions packed with product, or online
at Monogram.com, for current dimensional data.
* Shipping height.
The refrigerator
can be adjusted to
fit into a cutout that
is 83-1/2" min. to
84-1/2” max. height.
Note that the top
case trim at the
front is 1/2" higher
and will overlap
upper cabinetry or
soffit. Use leveling
legs and wheels
for a maximum 1"
height adjustment.
Water and electrical locations
The opening must be prepared with the electrical and water
supply located as shown.
The cutout depth must be 24".
The refrigerator will project forward, slightly beyond
adjacent cabinetry, depending on your installation.
The cutout depth beneath a soffit:
When installed beneath a soffit, the soffit cannot exceed the
24" installation depth shown. The top case trim overlaps the
bottom of the soffit.
Additional Specifications
• A 115 volt 60Hz., 15 or 20 amp power supply is required.
An individual properly grounded branch circuit or circuit
breaker is recommended. Install a properly grounded 3prong electrical receptacle recessed into the back wall.
Electrical must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
• Water line can enter the opening through the floor or back
wall. The water line should be 1/4" O.D. copper tubing or
GE SmartConnect™ kit between the cold water line and
water connection location, long enough to extend to the
front of the refrigerator. Installation of an easily accessible
shut off valve in the water line is recommended.
For answers to your Monogram,® GE Profile™
or GE® appliance questions, visit our website
at ge.com or call GE Answer Center® service,
800.626.2000.
Specification Revised 11/08
Listed by
Underwriters
Laboratories
110168
ZIS480NX
Framed Panel
3/4" Overlay Panel
.10" Thick Spacer Panel
1/4" Thick Backer Panel
*84"
2-9/16"
24"
*3" to 4"
3/16"
1-7/8"
GE Monogram® 48" Built-In Side-by-Side Refrigerator with Automatic
Icemaker and Water Filter
Dimensions and Installation Information (in inches)
Customization Basics: Framed or Overlay Panels, Custom Handles and Accessory Kits
Trimmed Refrigerators
ZIS480NXSS, ZISW480DXSS, ZISB480DXSS
Trimmed refrigerators are designed to be customized with
decorative panels. Field-installed custom door and grille
panels are required.
Framed Panels
You may install 1/4"-thick custom panels from your cabinet
manufacturer. The decorative panels slide into the factoryinstalled trim. Or, order black, white and stainless steel
accessory panels from your Monogram dealer.
Standard supplied handles shown in 1/4" panel position.
Overlay Panels
You may also choose to install custom overlay panels from
your cabinet manufacturer. This design provides a seamless
appearance which integrates smoothly with surrounding
cabinetry.
Door Handles
The supplied handles can be adjusted to accommodate both
framed or overlay panels. Custom handles of your choice,
supplied by your cabinet maker, can also be installed. If
desired, you may order ZKHSS2 Monogram stainless steel
tubular handle kit for overlay panels.
Side Panels
Side panels must be used whenever
the sides of the refrigerator will be
exposed. The 1/4" side panels will
slip into the side case trim. Secure
the panels to the refrigerator with
stick-on hook and loop fastener
strips. Order the side panels from
the cabinet manufacturer.
• Cut a notch in the top front corner
as shown to allow clearance for
corner keys in the front side trim.
Standard supplied handles shown in 3/4" overlay panel position.
For answers to your Monogram,® GE Profile™
or GE® appliance questions, visit our website
at ge.com or call GE Answer Center® service,
800.626.2000.
*Depending on installation height.
Optional Accessory Kit
ZKHSS2: Tubular Stainless Steel handles designed to fit
3/4" overlay panels.
Accessory Panels
White or black acrylic and stainless steel accessory panels
are available from your Monogram supplier. Panels are
cut to size and ready to install. These panel kits must be
ordered separately.
White Black Stainless
Models Acrylic Acrylic Steel
ZISW480D ZPW480D ZPS480D
ZISB480D ZPB480D ZPS480D
ZIS480N ZPW480N ZPB480N ZPS480N
Listed by
Underwriters
Laboratories
Specification Revised 11/08
110168
Loading...