GE Monogram ZIS360NR User Manual

23-7/8"
Behind

Frame

90° Door Swing

4" Min.
to Wall

20-5/8"

19"

130° Door Swing

13"

*84" From
Floor to
Top Frame

36"

Frame to Frame

35"

Case Width

*83-1/2"

at

Rear

25-3/4"

27-3/4"

including

handle

*Finished Width

6"

5"

Electrical
Area

84-1/2" max

83-1/2" min

Finished
Opening

75" From Floor

to Bottom

of Electrical

Area

24"

5"

5"

3-1/2"

Water Supply

3-1/2"

36" Models 12"
42" Models 18"
48" Models 20"

ZIS360NR – GE Monogram 36" Built-In Side-by-Side Refrigerator

with Automatic Icemaker and Water Filter

The Installation Space

Door Swing Clearances

Space is the first consideration when planning the installation.

The cutout depth must be 24"

The refrigerator will project forward, slightly beyond adjacent
cabinetry, depending on your installation.

The cutout depth beneath a soffit

When installed beneath a soffit, the soffit cannot exceed the
24" installation depth shown. The top case trim overlaps the
bottom of the soffit.

Electrical

A 115V, 60Hz., 15 or 20 amp power supply is required. An
individual properly grounded branch circuit or circuit breaker
is recommended. Install a properly grounded 3-prong electrical
receptacle recessed into the back wall. Electrical must be
located on rear wall as shown.

Listed by
Under writers
Labor atories

Note: GFI (ground fault interrupter) is not recommended.

Water Line

All models are equipped with an automatic icemaker. The
water line can enter the opening through the floor or back
wall. Route 1/4" O.D. copper tubing or GE QuickConnect
kit between the cold water line and the water connection
location. The copper tubing should be long enough to extend
to the front of the refrigerator. The installation of an easily
accessible shut-off valve in the water line is required.

Specification Revised 3/08

110110

The installation must allow for clearances to adjacent walls or
cabinets. These refrigerators are equipped with a 2-position
door stop. The factory-set 130° door swing can be adjusted to
90° if clearance to adjacent cabinets or walls is restricted.

Allow minimum clearances for freezer door and fresh food
door for a full 130° door swing and to allow for pan removal.

• 4" minimum clearance is required when door swing is
adjusted to 90°. If the 90° door stop position is used, pan
access is maintained, but pan removal is restricted.

• See door swing illustrations to determine interaction with
adjacent cabinets or countertops.

Installation Information: Before installing, consult
installation instructions packed with product, or online at
Monogram.com, for current dimensional data.

As an ENERGY STAR®
partner, GE has determined
that this product meets the
ENERGY STAR
for energy efficiency.

guidelines

For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.

* Shipping height.

The refrigerator
can be adjusted to
fit into a cutout that
is 83-1/2" min. to
84-1/2" max. height
The top case trim
at the front is 1/2"
higher and will
overlap upper
cabinetry or soffit.
Use leveling legs
and wheels for a
maximum 1" height
adjustment.

ZIS360NR – GE Monogram 36" Built-In Side-by-Side Refrigerator

Framed Panel

3/4" Overlay Panel

.10" Thick Spacer Panel

1/4" Thick Backer Panel

*84"

2-9/16"

24"

*3" to 4"

3/16"

1-7/8"

with Automatic Icemaker and Water Filter

Customization Basics: Framed or Overlay Panels, Custom Handles and Accessory Kits

Trimmed Refrigerators

ZIS360NRSS, ZISW360DRSS, ZISB360DRSS

Trimmed refrigerators are designed to be customized with decorative
panels. Field-installed custom door and grille panels are required.

Framed Panels

You may install 1/4"-thick custom panels from your cabinet
manufacturer. The decorative panels slide into the factory-installed
trim. Or, order black, white and stainless steel accessory panels
from your Monogram dealer.

Standard supplied handles shown in 1/4" panel position.

Overlay Panels

You may also choose to install custom overlay panels from your
cabinet manufacturer. This design provides a seamless appearance
which integrates smoothly with surrounding cabinetry.

Door Handles

The supplied handles can be adjusted to accommodate both framed
or overlay panels. Custom handles of your choice, supplied by your
cabinet maker, can also be installed. If desired, you may order ZKHSS2
Monogram stainless steel tubular handle kit for overlay panels.

Side Panels

Side panels must be used whenever
the sides of the refrigerator will be
exposed. The 1/4" side panels will
slip into the side case trim. Secure
the panels to the refrigerator with
stick-on hook and loop fastener strips.
Order the side panels from the
cabinet manufacturer.

• Cut a notch in the top front corner

as shown to allow clearance for
corner keys in the front side trim.

*Depending on installation height.

Optional Accessory Kit

ZKHSS2: Tubular Stainless Steel handles designed to fit
3/4" overlay panels.

Accessory Panels

White or black acrylic and stainless steel accessory panels are
available from your Monogram supplier. Panels are cut to size and
ready to install. These panel kits must be ordered separately.

White Black Stainless
Models Acrylic Acrylic Steel

ZISW360D ZPW360D ZPS360D
ZISB360D ZPB360D ZPS360D

ZIS360N ZPW360N ZPB360N ZPS360N

Standard supplied handles shown in 3/4" overlay panel position.

Specification Revised 3/08

110110

As an ENERGY STAR®
Listed by
Under writers
Labor atories

partner, GE has determined

that this product meets the

ENERGY STAR

for energy efficiency.

For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.

guidelines