GE Monogram ZICS360N RH User Manual
Installation
Instructions
If you have questions, call 800.626.2000 or visit our website at: www.monogram.com
ZIC360N RH, ZIC360N LH,
ZICS360N RH, ZICS360N LH
Built-In Bottom-Freezer
Refrigerators
Design Guide
With Installation Instructions
Monogram.
We bring good things to life.
®
Safety Information
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT - Save these instructions for
local inspector’s use. Observe all governing
codes and ordinances.
• Note to Installer - Be sure to leave these instructions with the Consumer.
• Note to Consumer - Keep these instructions with
your Owner’s Manual for future reference.
WARNING:
This appliance must be properly grounded. See
“Grounding the Refrigerator,” page 9.
AVERTISSEMENT
Cet appareil doit être correctement mis à la terre.
Consulter «␣ Mise à la terre du réfrigérateur␣ », page 9.
If you received a damaged refrigerator, you should
immediately contact your dealer or builder.
CAUTION:
Due to the weight and size of this refrigerator, and to
reduce the risk of personal injury or damage to the
product - TWO PEOPLE ARE REQUIRED FOR
PROPER INSTALLATION.
PRUDENCE
À cause du poids et de la taille de ce réfrigérateur et
pour réduire le risque de blessure et de dommages, IL
FAUT DEUX PERSONNES POUR FAIRE
L’INSTALLATION CORRECTEMENT.
Skill Level - Installation of this refrigerator requires
basic mechanical, carpentry and plumbing skills.
Proper installation is the responsibility of the installer. Product failure due to improper installation is
not covered under the GE Appliance Warranty. See
the Owner’s Manual for warranty information.
WARNING:
• These refrigerators are top-heavy and must be
secured to prevent the possibility of tipping forward. Anti-Tip protection is required. See page 11
for details.
• Use this appliance only for its intended purpose.
• Immediately repair or replace electric service cords
that become frayed or damaged.
• Unplug the refrigerator before cleaning or making
repairs.
• Repairs should be made by a qualified service
technician.
AVERTISSEMENT
• Ces réfrigérateurs sont lourds en haut et il faut les
arrimer pour éviter leur basculement. Il faut avoir
un système de protection contre le renversement.
Voir les détails page 11.
• Il ne faut utiliser cet appareil que pour l’utilisation
appropriée.
• Réparer ou remplacer immédiatement tout cordon
électrique effiloché ou endommagé.
• Il faut débrancher le réfrigérateur avant le
nettoyage ou toute intervention.
• Les réparations doivent être faites par un
technicien qualifié.
For Monogram local service in your area,
1-800-444-1845.
For Monogram service in Canada
1-888-880-3030
For Monogram Parts and Accessories, call
1-800-626-2002.
www. monogram.com
CONTENTS
Planning Guide
The Installation Space ....................................3
Dimensions and Clearances ..........................3
130° Door Swing .............................................. 4
90° Door Swing ................................................ 5
Customization Basics ..................................... 6
Panel Dimensions ............................................7
Side Panels .......................................................8
ZUG2 Grille Panel Dimensions ...................... 8
Installation Instructions
Tools, Hardware, Materials ........................... 9
Grounding the Refrigerator ............................9
Step 1, Remove Packaging .......................... 10
Step 2, Install Water Line .............................10
Step 2A, RO Water Line ................................11
Step 3, Install Side Panels ........................... 11
Step 4, Install Anti-Tip Brackets ................. 11
Step 5, Level Refrigerator ............................ 12
Step 6, Secure Refrigerator to Cabinetry .. 12
2
Step 7, Adjust Door Swing ........................... 13
Step 8, Install Grille Panel ............................13
Step 9, Install Framed Panels ......................14
Step 9A, Install Overlay Panels ...................15
Step 10, Connect Water Supply .................. 16
Step 11, Connect Power ...............................16
Step 12, Start Icemaker ................................ 16
Step 13, Install Toekick ................................. 16
Design Guide
THE INSTALLATION SPACE
The finished cutout width must be 35-1/2".
35-1/2"
Finished Width
5"
Wall View
74-1/2" From
Floor to
Bottom
of Electrical
2-5/16"
7"
84-1/2" max
83-1/2" min
Finished
Opening
10"
24" Cutout Depth
5"
3 1/2"
Electrical
Area
Water Supply
3 1/2"
Water And Electrical Locations
The opening must be prepared with the electrical and
water supply located as shown.
The cutout depth must be 24".
Designed for industry standard flush installation. The
refrigerator will project forward, slightly beyond
adjacent cabinetry, depending on your installation.
35"
Case Width
DIMENSIONS AND
CLEARANCES
* Shipping height. The
height may
*84"
be adjusted from
83-1/2" to 84-1/2" by
adjusting leveling legs
and wheels.
Product Clearances
These refrigerators are
36"
Frame to Frame
Width
equipped with a 2 position
door stop. The factory set
130° door swing can be
adjusted to 90° if clearance
to adjacent cabinets or
walls is restricted.
130° Door Swing 90° Door Swing
25"
Minimum
to Wall
23-7/8"
Behind
Frame
Additional Specifications
• A 115 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch
circuit or circuit breaker is recommended. Install a
properly grounded 3-prong electrical receptacle
recessed into the back wall. Electrical must be
located on rear wall as shown.
Note: GFI (ground fault interrupter) is not
recommended.
• Water line can enter the opening through the floor
or back wall. The water line should be 1/4" O.D.
copper tubing between the cold water line and
water connection location, long enough to extend
to the front of the refrigerator. Installation of an
easily accessible shut off valve in the water line is
recommended.
ZUG2, ZUGSS2 Unified Grille Panel Kit
• If you are installing two refrigerators, side by side,
the installation space must be 71-1/2" wide.
Note: Additional cutout width may be required when side panels
are used. Add side panel thickness to the finished cutout to
calculate rough-in width.
• The water and electrical locations for each product
must be located as shown.
• A separate 115V, 60Hz., 15 or 20 amp power supply
is recommended for each product.
36-3/4"
130°
90°
4" Minimum
to Wall
Allow 25" minimum clearance for a full 130° door
swing. Allow 15" for pan removal.
4" minimum clearance is required when door swing is
adjusted to 90°. If the 90° door stop position is used,
pan access is maintained, but pan removal is restricted bottom pans.
See illustrations pages 4 and 5 to determine door
swing interaction with adjacent cabinets or
countertops.
71-1/2" Finished Width
84-1/2" max
83-1/2" min
Finished
Opening
3-1/2"
2-5/16"
10"
24" Cutout
Depth
5"
Water Supply
Electrical
7"
26"
24-3/16"
7"
10"
Water Supply
26"
Wall View
74-1/2" From
Floor to Bottom
of Electrical
5"
3-1/2"
3
Design Guide
Refrigerator
23-7/8" From
Rear of
Refrigerator
Case
Trim
1/4"
1/2"
3/4"
1"
1-1/4"
1-1/2"
1-3/4"
2"
3"
2-3/4"
2-1/2"
2-1/4"
1/4"
1/2"
3/4"
1"
3/4" Overlay
Panel
(Nominal Size)
Top View
130° DOOR SWING
(factory setting)
Scale 1:1
Door
1/4"
1/2"
3/4"
1"
1-1/4"
4
Design Guide
Refrigerator
Case Trim
23-7/8"
From Rear of
Refrigerator
1/4"
Top View
90° DOOR SWING
Door
1/4"
1/2"
3/4"
1"
1-1/4"
1-1/2"
3/4" Overlay
Panel
(Nominal Size)
1/2"
(optional setting)
Scale 1:1
3/4"
1"
1-1/4"
5
Design Guide
Standard
Door Handle
3/4" Overlay Panel
1/4" Thick Backer Panel
.10" Thick Spacer Panel
CUSTOMIZATION BASICS:
Framed Or Overlay Panels, Custom Handles and Accessory Kits
Models Available
Stainless Steel Wrapped Models:
ZICS360N RH (right-handed door)
ZICS360N LH (left-handed door)
Trimmed models:
ZIC360N RH (right-handed door)
ZIC360N LH (left-handed door)
Stainless Steel Wrapped Refrigerators
Stainless Steel wrapped refrigerators have wrapped
doors and grille panel, beveled edges, and tubular
stainless steel handles that coordinate with other
Monogram appliances. These models are shipped
ready for installation.
Trimmed Refrigerators
Trimmed refrigerators are designed to be customized
with decorative panels. Field installed custom door and
grille panels are required.
Framed panels
You may install 1/4" thick custom panels from your
cabinet manufacturer. The decorative panel slides into
the factory installed trim. Or, order black, white and
stainless steel accessory panels from your Monogram
dealer.
Overlay panels
You may also choose to install custom overlay panels
from your cabinet manufacturer. This design provides a
seamless appearance which integrates smoothly with
surrounding cabinetry.
Standard supplied handles shown in 3/4" overlay panel position.
Door and Drawer Handles
The standard supplied handles can be adjusted to
accommodate both framed or overlay panels. Custom
handles of your choice, supplied by your cabinet maker
can also be installed. If desired, you may order ZKHCSS2
Monogram stainless steel tubular handle kit.
Standard Door Handle Framed Panel
Standard supplied handles shown in 1/4" panel position.
Optional Accessory Kits
• ZKHCSS2: Monogram Tubular Stainless Steel handles
designed to fit framed or overlay panels.
• ZUG2: For side by side installation of two trimmed
bottom-freezer refrigerators. This kit provides for the
installation of a unified custom grille panel to span the
width of two units using a framed or overlay panel.
• ZUGSS2: For side by side installation of two stainless
steel wrapped bottom-freezer refrigerators. This kit
provides a unified stainless steel grille panel to span
the width of two units.
Side Panels
Side panels must be used whenever the sides of the
refrigerator will be exposed.
Accessory Panels
White, black and stainless steel accessory panels are
available from your Monogram dealer. Panels are cut to
size and ready to install.
ZPBC360–Black, ZPWC360–White,
ZPSC360–Stainless Steel Panels
6
Loading...