GE Monogram ZDBC240NBS Owner's Manual

Page 1
Owner’s Manual
Beverage Center
ZDBC240
monogram.com
Page 2
2
Consumer Information
Introduction
Your new Monogram beverage center makes an eloquent statement of style, convenience and kitchen planning flexibility. Whether you chose it for its purity of design or the assiduous attention to detail, you will find that your Monogram beverage center’s superior blend of form and function will delight you for years to come.
The information on the following pages will help you operate and maintain your beverage center properly.
If you have any other questions, visit our Website at: monogram.com
Contents
Care and Cleaning . . . . . . . . . . . . . . . . . .10, 11
Consumer Services . . . . . . . . . . . . . . . . . . . .19
Controls and Features . . . . . . . . . . . . . . . . .8, 9
Model and Serial Numbers . . . . . . . . . . . . . . .2
Problem Solver . . . . . . . . . . . . . . . . . . . . .13–15
Product Registration . . . . . . . . . . . . . . . . . . . .2
Repair Service . . . . . . . . . . . . . . . . . . . . . . .3, 19
Reversing the Door Swing . . . . . . . . . . . . . .12
Safety Instructions . . . . . . . . . . . . . . . . . . . .4–7
Warranty . . . . . . . . . . . . . . . . . . . . .Back Cover
Before using your beverage center
Read this manual carefully. It is intended to help you operate and maintain your new beverage center properly.
Keep it handy for answers to your questions.
If you don’t understand something or need more help, there is a list of toll-free consumer service numbers included in the back section of this manual.
OR Visit our Website at: monogram.com
Write down the model & serial numbers
You will find them on a label on the ceiling inside the beverage center.
Please write these numbers here:
Model Number
Serial Number Use these numbers in any correspondence
or service calls concerning your beverage center.
ATTENTION CONSUMER!
This unit is designed for storing and cooling beverages. Do not store perishable foods in this unit.
ATTENTION CONSOMMATEUR !
Cet appareil ménager est conçu pour conserver et rafraîchir des boissons. Ne mettez pas de biens perissables dans cet appareil ménager.
Page 3
3
If you received a damaged appliance
The warranty does not cover damage caused after delivery.
Immediately contact the dealer (or builder) that sold you the beverage center.
If you need service
To obtain service, see the Consumer Services page in the back of this manual.
We are proud of our service and want you to be pleased. If for some reason you are not happy with the service you receive, here are steps to follow for further help.
For customers in the USA:
FIRST, contact the people who serviced your appliance. Explain why you are not pleased. In most cases, this will solve the problem.
NEXT, if you are still not pleased, write all the details—including your phone number—to:
Manager, Customer Relations GE Appliances Appliance Park Louisville, KY 40225
For customers in Canada:
FIRST, contact the people who serviced your appliance. Explain why you are not pleased. In most cases, this will solve the problem.
NEXT, if you are still not pleased, write all the details—including your phone number to:
Manager, Consumer Relations Mabe Canada Inc. 1 Factory Lane, Suite 310 Moncton, N.B. E1C 9M3
Consumer Information
After installation is completed
• Promptly inspect your new Monogram Beverage Center. If it has been damaged, contact the Installer or Dealer immediately.
• This Beverage Center must be properly leveled to ensure correct door alignment and door closure. Contact the Installer if the unit is not level.
• The unit should be centered in the opening. The front face of the door should be 1forward of adjacent cabinetry. Contact the installer if clearance is not correct.
• Test the door swing. Carefully open and close the door. The door should not rub or catch on adjacent cabinetry. Notify the installer if the door makes contact with cabinetry.
Please Contact the Installer or Dealer if you experience any of these problems.
Your Beverage Center is shipped with a black toekick on the front of the unit. For shipping purposes, an optional stainless steel toekick is secured to the back of the unit. That toekick should have been removed and installed, or given to you. Keep the unused toekick and other unused or removed parts for possible future use.
Remove packaging
Before using, be sure all packing materials and tape have been removed.
To assure no damage is done to the finish of the product, the safest way to remove the adhesive left from packaging tape on
new appliances is an application of household liquid detergent. Apply with a soft cloth and allow to soak. Wipe dry and then apply an appliance polish to thoroughly clean and protect the surface.
Page 4
4
REFRIGERANTS
All refrigeration products contain refrigerants, which under federal law must be removed prior to product disposal.
If you are getting rid of an old refrigeration product, check with the company handling the disposal about what to do.
wDANGER: RISK OF CHILD ENTRAPMENT
Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigeration products are still dangerous…even if they will sit for “just a few days.” If you are getting rid of your old appliance, please follow these instructions to help prevent accidents.
Before You Throw Away Your Old Refrigeration Product:
•Take off the doors.
•Leave the shelves in place so that children may not easily climb inside.
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
BEFORE IT IS USED, THE APPLIANCE MUST BE PROPERLY INSTALLED AND LOCATED AS DESCRIBED IN THIS MANUAL.
USE OF EXTENSION CORDS
Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord.
However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed, 3-wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.
Page 5
wDANGER! RISQUES POUR LES ENFANTS
Les enfants pris au piège ou morts d’asphyxie sont toujours d’actualité. Les appareils de réfrigération abandonés sont toujours aussi dangereux, même si on n’attend que “quelque jours” pour s’en débarasser. Si vous ne gardez pas votre ancien appareil, veuillez suivre les directives ci-dessous afin de prévenir les accidents.
Avant de vous débarasser de votre vieux appareil de réfrigération :
•Démontez les portes.
•Laissez les clayettes en place afin d’empêcher les enfants de grimper à l’intérieur.
RÉFRIGÉRANTS
Tous les appareils de réfrigération contiennent des refrigerants qui, conformément aux lois fédérales, doivent être enlevés avant toute élimination de l’appareil.
Si vous vous débarrassez de vieux appareils de réfrigération, vérifiez, auprès de la société qui s’occupe de leur élimination, ce que vous devez faire.
IMPORTANTES INSTRUCTIONS DE SÉCURITÉ
LIRE ET CONSERVER CES INSTRUCTIONS
5
AVANT D’ÊTRE UTILISÉ, L’APPAREIL MÉNAGER DOIT ÊTRE BIEN INSTALLÉ ET SE TROUVER À L’ENDROIT DÉCRIT DANS CETTE MANUEL.
CORDONS PROLONGATEURS
Nous vous recommandons fortement de ne pas utíliser de cordons prolongateurs à cause des risques potentiels qu’ils présentent dans certaines conditions.
Toutefois si vous décidez d’utiliser tout de même un cordon prolongateur, il est absolument nécessaire qu’il s’agisse d’un cordon à 3 fils avec mise à la terre pour appareils électroménagers homologué UL (aux États-Unis) ou homologué CSA (au Canada), pourvu d’une fiche et d’une prise mises à la terre de 15 ampères (minimum) et de 120 volts.
Page 6
6
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.
The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance.
Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.
Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.
The appliance should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate. This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.
Never unplug an appliance by pulling on the power cord. Always grip the plug firmly and pull straight out from the outlet.
Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.
When moving the appliance, be careful not to roll over or damage the power cord.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Page 7
7
RACCORDEMENT ÉLECTRIQUE
Ne coupez ni retirez en aucun cas la troisième broche (mise à la terre) de la fiche du cordon d’alimentation. Pour votre sécurité, cet appareil doit être correctement mis à la terre.
Le cordon d’alimentation de cet appareil est muni d’une fiche à 3 broches (mise à la terre) qui se branche dans une prise mural ordinaire à 3 alvéoles (mise à la terre) pour réduire au minimum les risques du chocs électriques.
Faites examiner la prise de courant et le circuit par un électricien qualifié pour vous assurer que la prise est correctement mise à la terre.
Si la prise murale est du type standard à 2 alvéoles, il vous incombe de la faire remplacer par une prise à 3 alvéoles correctement mise à la terre.
Le appareil doit toujours être branché dans sa propre prise de courant, dont la tension nominale est identique à celle indiquée sur la plaque signalétique.
Cette précaution est recommandée pour garantir un rendement optimum et éviter une surcharge des circuits électriques de la résidence, ce qui pourrait créer un risque d’incendie par surschauffe des fils.
Ne débranchez jamais l’appareil en tirant le cordon d’alimentation. Saisissez fermement la fiche du cordon et tirez droit pour la retirer de la prise.
Réparez ou remplacez immédiatement tout cordon effiloché ou endommagé. N’utilisez pas un cordon fendillé ou présentant des signes d’usure.
Lorsque vous déplacez l’appareil du mur, faites attention de ne pas la faire rouler sur le cordon d’alimentation afin de ne pas l’endommager.
IMPORTANTES INSTRUCTIONS DE SÉCURITÉ
CONSERVEZ CES DIRECTIVES
Page 8

Controls and Features

Interior light and switch
The interior light makes it easy to view your beverage labels and enhances the display of your collection.
When the switch is in the OFF position, the light comes on only when the door is opened. When the switch is in the ON position, the light remains on continuously for your maximum viewing pleasure. For best viewing, do not store a bottle on the top shelf directly under the light. Remember to turn off the light when it is no longer needed.
Glass shelves
Tempered glass shelves in the beverage center unit are removable for easy cleaning or for storing larger items.
To remove a shelf, open the door completely to avoid potential damage to the gasket. Lift up on the back of the shelf slightly. Tilt the shelf to one side at an angle while pulling forward.
To replace a shelf, open the door completely to avoid potential damage to the gasket. Tilt the shelf to one side at an angle and slide toward the back wall, placing one side onto the shelf support. Place the other side onto the opposite shelf support. Ensure rear locking tabs are engaged. When installed properly, the shelf will not slide forward when gently pulled.
Temperature control
The operating temperatures of the beverage center range from the low forties to the mid fifties.
This appliance is not a refrigerator and does not maintain temperatures like a refrigerator (below 40°F).
Do not install the beverage center where the temperature will go below 55°F (13°C) or above 90°F (32°C).
As with any refrigeration-type product, there is a slight temperature variance at different locations within the cabinet.
The coolest area will be in the lower part of the cabinet.
The cooler area will be in the middle section. The upper part of the cabinet is the
warmest section. When the temperature is adjusted, allow
24 hours for the unit to stabilize.
To set the control, turn it to the midpoint setting (approximately 45ºF). Once the beverage center is loaded, allow at least 24 hours before making any adjustments to the initial setting.
NOTES:
This unit is designed for storing and
cooling beverages. It is not intended for the storage of perishable foods.
The lowest temperatures are found on the lower shelves/racks and toward the rear of the shelves/racks.
8
To remove, lift up on the back of the shelf Tilt the shelf at an angle while removing
or replacing
Place in slots when replacing the shelf
Page 9
Controls and Features
Loading tips and suggestions
The bottom two full extension drawers hold six bottles each and are loaded with necks facing the rear. Tall bottles should not be loaded on the bottom drawer because they may prevent the door from closing.
Do not allow children to climb, stand or hang on the beverage center shelves or full extension drawers. They could seriously injure themselves and possibly cause damage to the beverage center.
NOTE: This unit is for storing beverages only and not intended for the storage of perishable foods.
Bottom drawer arrangement
Removing full extension drawers
The bottom full extension drawers pull out so bottles can conveniently be added or removed.
The upper full extension slide can be removed for magnums or larger bottles.
To remove:
1. Pull the full extension drawer out to the
STOP position.
2. Push the tab on right drawer guide down
while pulling the tab on left guide up, and pull the drawer out.
To replace:
1. Push the drawer slide arm back into
the unit.
2. Pull the small slide sub-assembly
completely forward.
3. Insert the sides of the drawer back
into the guides.
4. Push until the tabs lock into place.
Tab (push tab down on right drawer guide, pull tab up on left drawer guide)
Wood drawer fronts
The full extension drawer fronts on the beverage center are unfinished cherry wood. During use, oil from hands may accumulate and stain the wood.
The drawer fronts may be stained and
sealed to match adjacent cabinetry. The tinted glass will make the stained wood appear darker. A true color match can be seen only when the door is opened.
Apply the stain and sealer according to
the manufacturer’s instructions. To avoid unpleasant odor, keep the door open to ventilate and allow the stain/sealer to dry completely before using the product.
NOTE: Natural wood may vary slightly in grain and color.
9
NOTE: Make sure the tabs on the full extension drawer guides are fully engaged before loading any bottles. Pull the drawers out all the way to the STOP position and push back in several times to make sure locking tabs are properly engaged.
To replace, push drawer slide arm back into unit
Pull small slide sub-assembly completely forward
Sub-assembly
Sub-assembly
Page 10
Glass door
Use a glass cleaner or mild soap and water and a soft cloth to clean the glass door. Do not use any abrasive powders.
Door gasket
The vinyl gasket may be cleaned with mild soap and water, a baking soda solution or a mild scouring powder. Rinse well.
After cleaning the door gasket, apply a thin layer of paraffin wax or petroleum jelly to the door gasket at the hinge side. This helps keep the gasket from sticking and bending out of shape.
Light bulb replacement
Unplug the beverage center before replacing the light bulb.
To remove the light shield, push in the tab on the left side of the shield and lower it. Replace with a 15 watt appliance bulb.
In the event of a power failure
If the power fails, open the door as infrequently as possible to maintain the temperature.
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

Care and Cleaning

Unplug the beverage center before cleaning.
Cabinet
The exterior surfaces can be washed with mild soap and water. Rinse thoroughly with clear water. Never use abrasive scouring powders.
10
Page 11
Care and Cleaning
Cleaning the inside
Turn the beverage center unit OFF or unplug the unit before cleaning. Use a
slightly damp cloth or sponge when cleaning around switches, lights or controls.
Use warm water and baking soda solution— about a tablespoon (15 ml) of baking soda to a quart (1 liter) of water. This both cleans and neutralizes odors. Thoroughly rinse and wipe dry.
Other parts of the beverage center unit— including the door gaskets, full extension drawers and glass shelves—can be cleaned the same way.
Avoid cleaning cold glass shelves with hot water because the extreme temperature difference may cause them to break. Handle glass shelves carefully. Rough handling of tempered glass can cause it to shatter.
Drain hole
Periodically check the drain hole and channel for any debris. If the drain is blocked, condensation will not drain properly.
To check and clean the drain hole, remove the bottom two glass shelves. Sweep a damp cloth along the channel in the back of the beverage center. Use a finger to sweep away any debris from the drain hole.
11
Unplug the beverage center before cleaning.
Drain hole
Page 12

Reversing the Door Swing

To reverse the door
Parts included:
1. Top left case hinge
2. Bottom left case hinge
3. Left and right side decorative hinge
cover
4. Decorative hinge screw hole cover
5. Torx
®
driver bit
Tools required:
1. Phillips screwdriver
2. Electric drill
To remove the door:
1. Flatten the shipping carton to use as
a pad.
2. Remove the 2 screws and the toekick.
Set aside the screws and toekick for final installation.
3. Use the supplied Torx
®
bit and electric drill to remove the 3 screws holding the top case hinge. Lift off the hinge. (Screws will be used to install the new hinge.)
4. Lift the door off the bottom case hinge.
5. Remove the bottom case hinge pin
and bracket.
Rotate the door:
The handle will be on the right side of the door; hinges will be installed on the left side of the case.
1. Remove the door stop and cam riser
on the original bottom right side of the door.
2. Remove the fill plug on the top right side
of the door.
3. Turn the door over and reinstall the
fill plug on the new left side.
To reinstall the door:
1. Install the original door stop and cam
riser onto the bottom left side of the door.
2. Install the new supplied bottom case
hinge pin and bracket onto bottom left side.
3. Place the door onto the bottom case
hinge.
4. Install the supplied left-hand top case
hinge with the 3 original screws.
5. Select the hinge cover marked with
an “L”.
6. Peel backing off the tape inside
the decorative hinge cover.
7. Press and snap
the hinge cover into place.
8. Snap the screw
hole cover into place on the opposite side.
Important: Check to be sure screws are tight and that the door is straight and does not sag. The door should swing freely.
Note: See Installation Instructions to apply hinge cover and screw hole cover.
Position nameplate:
Apply the Monogram nameplate on the door using the template included in the installation instructions.
12
Install
3 Hinge
Screws
Door Stop
and Cam Riser
Remove
Top Hinge
Hinge Pin and Bracket
Remove
Hinge
Install Covers
Page 13
13
You may hear cracking or popping sounds
when the appliance is first plugged in. This happens as the appliance cools to the correct temperature.
Expansion and contraction of cooling coils
during and after defrost can cause a cracking or popping sound.
The flow of refrigerant through the
appliance cooling coils may make a gurgling noise like boiling water.
A water dripping noise may occur as
water from the evaporator flows into the drain pan.
Closing the drawer may cause a gurgling
sound due to pressure equalization.
Normal operating sounds
Newer appliances sound different from older appliances. Modern appliances have more features and use newer technology.
HUMMM...
WHOOSH...
CLICKS, POPS,
CRACKS and CHIRPS
WATER SOUNDS
Do you hear what I hear? These sounds are normal.
The new high efficiency compressor
may run faster and longer than your old appliance and you may hear a high­pitched hum or pulsating sound while it is operating.
Sometimes the appliance runs for an
extended period, especially when the doors are opened frequently.
You may hear a whooshing sound when
the doors close. This is due to pressure equalizing within the appliance.
You may hear the fans spinning at high
speeds. This happens when the appliance is first plugged in, when the door is opened frequently or when large amounts of beverages are added to the appliance. The fans help maintain desired temperatures.
If the door is open for over 3 minutes, you
may hear a fan come on in order to cool the appliance.
The fans change speeds in order to provide
optimal cooling and energy savings.
The Problem Solver
Page 14
14
Questions? Use this
problem solver!
PROBLEM POSSIBLE CAUSE
APPLIANCE • Appliance may be in defrost cycle when motor does not operate for DOES NOT OPERATE about 30 minutes.
• If interior light is not on, appliance may not be plugged in at wall outlet. Push the plug completely into the wall outlet.
• The fuse is blown/circuit breaker is tripped. Replace fuse or reset the breaker.
VIBRATION OR • Adjust the leveling legs as shown in the Installation Instructions. RATTLING (Slight vibration is normal.)
MOTOR OPERATES • Normal when appliance is first plugged in. Wait 24 hours for the FOR LONG PERIODS appliance to completely cool down. OR CYCLES ON AND
• Often occurs when large amounts of beverages are placed in appliance.
OFF FREQUENTLY
This is normal.
• Door left open or package holding door open.
• Hot weather or frequent door openings. This is normal.
• Temperature control set at the coldest setting. See Temperature Control. Allow 24 hours for temperature to change.
COMPARTMENT • Temperature control not set cold enough. TOO WARM See Temperature Control. Allow 24 hours for temperature to change.
• Warm weather or frequent door openings.
• Door left open for long time.
• Package may be holding door open.
APPLIANCE • Interior needs cleaning. See Care and Cleaning. HAS ODOR
• Keep open box of baking soda in appliance; replace every 3 months.
DOOR NOT • Door gasket is sticking or folding over. Apply petroleum jelly CLOSING or paraffin wax to the face of the gasket. PROPERLY
• The door is hitting an internal component inside the appliance. Adjust interior components to prevent interference.
MOISTURE FORMS • Not unusual during periods of high humidity. If bothersome, ON OUTSIDE OF wipe surface dry; otherwise, moisture will evaporate in time. APPLIANCE
• Door left open or package holding door open.
FROST OR MOISTURE • Too frequent or too long door openings. COLLECTS INSIDE
• In humid weather, air carries moisture into appliance when door is opened. Unit will dissipate moisture in time. If bothersome, wipe surface dry.
• Temperature control set at coldest setting.
INTERIOR LIGHT • No power at outlet. DOES NOT WORK
• Light bulb needs replacing. See Care and Cleaning.
The Problem Solver
Page 15
15
Questions? Use this
problem solver!
PROBLEM POSSIBLE CAUSE
HOT AIR FROM • Normal air flow cooling motor. In the refrigeration process, it is BOTTOM OF normal that heat be expelled in the area under the appliance. APPLIANCE Some floor coverings are sensitive and will discolor at these safe
and normal temperatures.
APPLIANCE • Adaptive defrost keeps compressor running during door openings. NEVER SHUTS OFF This is normal. The appliance will cycle off after the door remains BUT TEMPERATURES closed for two hours. ARE OK
• Normal operation in extreme temperatures.
The Problem Solver
Page 16
16
Wine or Beverage Storage and Handling Notes
Page 17
Wine or Beverage Storage and Handling Notes
17
Page 18
Appliance Notes
18
Page 19
19

Consumer Services

With the purchase of your new Monogram appliance, receive the assurance that if you ever need information or assistance from GE, we will be there. All you have to do is call—toll-free!
GE Answer Center
®
In the USA:
800.626.2000
Whatever your question about any Monogram major appliance, GE Answer Center
®
information service is available to help. Your call—and your question—will be answered promptly and courteously. And you can call any time. GE Answer Center®service is open 24 hours a day, Monday through Saturday.
OR Visit our Website at: monogram.com
In Canada, call 1.800.561.3344.
In-Home Repair Service
In the USA:
800.444.1845 In Canada:
1.800.561.3344
A GE consumer service professional will provide expert repair service, scheduled at a time that’s convenient for you. Many GE Consumer Service company-operated locations offer you service today or tomorrow, or at your convenience (7:00 a.m. to 10:00 p.m. weekdays, 8:00 a.m. to 6:00 p.m. Saturday and Sunday). Our factory-trained technicians know your appliance inside and out—so most repairs can be handled in just one visit. In Canada: Monday to Friday, 7:00 a.m. to 8:00 p.m. and Saturday, 8:00 a.m. to 5:00 p.m. EDST.
For Customers With Special Needs…
In the USA:
800.626.2000
GE offers Braille controls for a variety of GE appliances, and a brochure to assist in planning a barrier-free kitchen for persons with limited mobility.
Consumers with impaired hearing or speech who have access to a
TDD or a conventional teletypewriter may call 800.TDD.GEAC (800.833.4322) to request information or service.
Service Contracts
In the USA:
800.626.2224 In Canada:
1.800.561.3344
You can have the secure feeling that GE Consumer Service will still be there after your warranty expires. Purchase a GE contract while your warranty is still in effect and you’ll receive a substantial discount. With a multiple-year contract, you are assured of future service at today’s prices.
Parts and Accessories
In the USA:
800.626.2002 In Canada:
1.800.561.3344
Individuals qualified to service their own appliances can have parts or accessories sent directly to their home. The GE parts system provides access to over 47,000 parts…and all GE Genuine Renewal Parts are fully warranted. VISA, MasterCard and Discover cards are accepted.
User maintenance instructions contained in this manual cover procedures intended to be performed by any user. Other servicing generally should be referred to qualified service personnel. Caution must be exercised, since improper servicing may cause unsafe operation.
Page 20
YOUR MONOGRAM BEVERAGE CENTER WARRANTY Staple sales slip or cancelled check here. Proof of original purchase date is needed to obtain service under warranty.
Consumer Services
WHAT IS COVERED
From the Date of the Original Purchase
LIMITED ONE-YEAR WARRANTY
For one year from date of original purchase, we will provide, free of charge, parts and service labor in your home to repair or replace any part of the unit that fails because of a manufacturing defect.
LIMITED FIVE-YEAR WARRANTY
For five years from date of original purchase, we will provide, free of charge, parts and service labor in your home to repair or replace any part of the sealed refrigerating system (the compressor, condenser, evaporator and all connecting tubing) that fails because of a manufacturing defect.
This warranty is extended to the original purchaser and any succeeding owner for products purchased for ordinary home use in the 48 mainland states, Hawaii, Washington, D.C. or Canada. If the product is located in an area where service by a GE Authorized Servicer is not available, you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Service location for service. In Alaska the warranty is the same except that it is LIMITED because you must pay to ship the product to the service shop or for the service technician’s travel costs to your home.
All warranty service will be provided by our Factory Service Centers or by our authorized Customer Care
®
servicers during normal working hours. Should your appliance need service, during warranty period or beyond, in the USA call 800.444.1845. In
Canada: 800.561.3344. Please have your serial number and model number available when calling for service.
Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state/province to province. To know what your legal rights are in your state/province, consult your local or state/provincial consumer affairs office or your state’s Attorney General.
Warrantor in USA: General Electric Company,
Louisville, KY 40225
Warrantor in Canada: Mabe Canada Inc.,
Burlington, Ontario
WHAT IS NOT COVERED
• Service trips to your home to teach you how to use the product.
• Replacement of house fuses or resetting of circuit breakers.
• Damage to the product caused by accident, fire, floods or acts of God.
• Failure of the product if it is used for other than its intended purpose or used commercially.
• Damage caused after delivery.
• Improper installation, delivery or maintenance. If you have an installation problem, contact
your dealer or installer. You are responsible for providing adequate electrical, plumbing and other connecting facilities.
• Replacement of the light bulbs, if included.
• Loss of food due to spoilage (in the USA only).
• Incidental or consequential damage caused by possible defects with this appliance.
• Product not accessible to provide required service.
197D4614P006 49-60430-2
Printed in Slovenia
08-07 JR
EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest period allowed by law.
GE Consumer & Industrial
Appliances General Electric Company Louisville, KY 40225 ge.com
Loading...