Gemini Sound TT-01 Owners manual
BELT-DRIVE STRAIGHT ARM TURNTABLE
PLA TTENSPIELER MITRIEMENANTRIEB UND GERADEM TONARM
GIRADISCOS DE BRAZO RECTO TRACCIÓN POR CORREA
PLA TINE VINYLE A VEC ENTRAÎNEMENTP AR COURROIE ETBRAS DROIT
OPERATIONS MANUAL
BEDIENUNGSHANDBUCH
MANUAL DEL OPERADOR
MANUEL D’INSTRUCTIONS
MULTI LANGUAGE INSTRUCTIONS
ENGLISH.....................................................................................................................................................................................................................PAGE 4
DEUTSCH....................................................................................................................................................................................................................PAGE 6
ESPAÑOL....................................................................................................................................................................................................................PAGE 8
FRANCAIS.................................................................................................................................................................................................................PAGE 10
PLEASE READ BEFORE USING APPLIANCE, IMPORTANT WARNING & SAFETYINSTRUCTIONS!
CAUTION
RISK OF ELECTRICAL SHOCK DO NOT OPEN!
CAUTION: This product satisfies FCC regulations when shielded cables and connectors are used
to connect the unit to other equipment. To prevent electromagnetic interference with electric
appliances such as radios and televisions, use shielded cables and connectors for connec
tions.
The exclamation point within an equilateral triangle is intended to alert the user to the presence
of important operating and maintenance (servicing) instructions in the literature accompanying
the appliance.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute a risk of electric shock to persons.
READ INSTRUCTIONS: All the safety and operating instructions should be read
before the product is operated.
RETAIN INSTRUCTIONS: The safety and operating instructions should be retained
for future reference.
HEED WARNINGS: All warnings on the product and in the operating instructions
should be adhered to.
FOLLOW INSTRUCTIONS: All operating and use instructions should be followed.
CLEANING: The product should be cleaned only with a polishing cloth or a soft dry
cloth. Never clean with furniture wax, benzine, insecticides or other volatile liquids
since they may corrode the cabinet.
ATTACHMENTS: Do not use attachments not recommended by the product manu
facturer as they may cause hazards.
WATER AND MOISTURE: Do not use this product near water, for example, near a
bathtub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a
swimming pool; and the like.
ACCESSORIES: Do not place this product on an unstable cart, stand, tripod, brack
et, or table. The product may fall, causing serious injury to a child or adult, and seri
ous damage to the product. Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with the product. Any mounting of the
product should follow the manufacturer’s instructions, and should use a mounting
accessory recommended by the manufacturer.
CART: A product and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the product and cart combina
tion to overturn. See Figure A.
VENTILATION: Slots and openings in the cabinet are provided for ventilation and to
ensure reliable operation of the product and to protect it from overheating, and
these openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug, or other similar surface. This
product should not be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer’s instructions have been
adhered to.
POWER SOURCES: This product should be operated only from the type of power
source indicated on the marking label. If you are not sure of the type of power sup
ply to your home, consult your product dealer or local power company.
LOCATION: The appliance should be installed in a stable location.
NON-USE PERIODS: The power cord of the appliance should be unplugged from the
outlet when left unused for a long period of time.
GROUNDING OR POLARIZATION:
• If this product is equipped with a polarized alternating current line plug (a plug
having one blade wider than the other), it will fit into the outlet only one way. This
is a safety feature. If you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the safety purpose of the polarized
plug.
• If this product is equipped with a three-wire grounding type plug, a plug having a
third (grounding) pin, it will only fit into a grounding type power outlet. This is a
safety feature. If you are unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not defeat the safety purpose of the
grounding type plug.
POWER-CORD PROTECTION: Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience receptacles, and the
point where they exit from the product.
OUTDOOR ANTENNA GROUNDING: If an outside antenna or cable system is
connected to the product, be sure the antenna or cable system is grounded so as
to provide some protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information
with regard to proper grounding of the mast and supporting structure, grounding of
the lead-in wire to an antenna discharge unit, size of grounding conductors, loca
(2)
tion of antenna-discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode. See Figure B.
LIGHTNING: For added protection for this product during a lightning storm, or when
it is left unattended and unused for long periods of time, unplug it from the wall out
let and disconnect the antenna or cable system. This will prevent damage to the
product due to lightning and power-line surges.
POWER LINES: An outside antenna system should not be located in the vicinity of
overhead power lines or other electric light or power circuits, or where it can fall
into such power lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such power lines or circuits
as contact with them might be fatal.
OVERLOADING: Do not overload wall outlets, extension cords, or integral conven
ience receptacles as this can result in a risk of fire or electric shock.
OBJECT AND LIQUID ENTRY: Never push objects of any kind into this product
through openings as they may touch dangerous voltage points or short-out parts
that could result in a fire or electric shock. Never spill liquid of any kind on the
product.
SERVICING: Do not attempt to service this product yourself as opening or removing
covers may expose you to dangerous voltage or other hazards. Refer all servicing
to qualified service personnel.
DAMAGE REQUIRING SERVICE: Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the following conditions:
• When the power-supply cord or plug is damaged.
• If liquid has been spilled, or objects have fallen into the product.
• If the product has been exposed to rain or water.
• If the product does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions as an
improper adjustment of other controls may result in damage and will often require
extensive work by a qualified technician to restore the product to its normal oper
ation.
• If the product has been dropped or damaged in any way.
• When the product exhibits a distinct change in performance, this indicates a need
for service.
REPLACEMENT PARTS: When replacement parts are required, be sure the service
technician has used replacement parts specified by the manufacturer or have the
same characteristics as the original part. Unauthorized substitutions may result in
fire, electric shock, or other hazards.
SAFETY CHECK: Upon completion of any service or repairs to this product, ask the
service technician to perform safety checks to determine that the product is in
proper operating condition.
WALLOR CEILING MOUNTING: The product should not be mounted to a wall or ceil
ing.
HEAT: The product should be situated away from heat sources such as radiators,
heat registers, stoves, or other products (including amplifiers) that produce heat.
TT-01mkii
(3)
INTRODUCTION:
Congratulations on purchasing a Gemini TT-01MKII belt drive manual
turntable. This state of the art turntable includes the latest features.
Prior to use, we suggest that you carefully read all the instructions.
FEATURES
• +/-10% Variable pitch slider
• Solid aluminum platter
• Straight tonearm for superior tracking
• Fully adjustable counter weight & anti-skating controls
• Dual speed RPM (33/45)
• LED Illuminated soft touch start/stop & RPM buttons
• Removable head shell
• CN-1000 cartridge & felt slipmat included
• RCA & ground cables
PRECAUTIONS:
1. Read all operating instructions before using this equipment.
2. The apparatus should not be exposed to dripping or splashing, and no
objects filled with liquids such as vases should be placed on the apparatus.
3. To reduce the risk of electrical shock, do not open the unit. THERE
ARE NO USER REPLACEABLE PARTS INSIDE. Please contact the
Gemini Service Department or your authorized dealer to speak to a qualified service technician.
4. Tone Arm bearings are factory set and sealed. Any attempt at adjustment will void the warranty.
5. Be sure that all AC power is OFF while making connections.
6. Cables should be low capacitance, shielded and of proper length.
Make sure that all plugs and jacks are tight and properly connected.
7. Always, begin with the audio level faders/volume controls set at minimum and the speaker volume control(s) set to OFF. Wait 8 to 10 seconds prior to turning up the speaker volume to prevent the transient
“POP” that could result in speaker/crossover damage.
2. Replace the platter and rotate the PLATTER (2) until the MOTOR
SPINDLE (5) is visible, then fit your fingers in hole on the top of the
PLATTER (2), feel for and grab the rubber belt and attach to the motor
spindle.
3. Replace the locking washer.
TURNTABLE INSTALLATION:
1. Put the SLIPMAT (6) on the PLATTER (2).
2. Set the TURNTABLE BASE (1) on a flat, level surface free of vibration. Use the turntable feet to stabilize the unit horizontally.
3. Try to place the unit as far away from the speakers as possible.
4. Keep the unit away from direct exposure to the sun, heat, moisture or
dirt.
5. Keep the unit well ventilated.
CARTRIDGE INSTALLATION: (SEE FIG. 1)
Because all cartridges have their own designs, please refer to your
particular cartridge’s instructions to insure proper installation. If you are
using a pre-mounted or integrated cartridge, you can jump ahead to
HEADSHELL INSTALLATION:
1. Connect the lead wires to the cartridge terminals. For your convenience, the terminals of most cartridges are color-coded. Connect each
lead wire to the terminal of the same color. Incase your cartridge is not
marked the positive leads are the ones on top negative below, left are
left, and right is right.
White (L+)........................................................................Left Channel +
Blue (L-).............................................................................Left Channel -
Red (R+).........................................................................Right Channel +
Green (R-).......................................................................Right Channel -
2. Mount the cartridge in the HEADSHELL (7) and tighten it with the
screws included with the cartridge.
8. DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
9. DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY
CONTROLS OR SWITCHES.
PARTS CHECKLIST:
Please make sure the following parts are included with your TT-01MKII:
Turntable unit..........................................................................................1
Turntable platter......................................................................................1
Slipmat....................................................................................................1
Counterweight.........................................................................................1
Headshell with cartridge.........................................................................1
ASSEMBLY & SET-UP:
SEE FIG. 3 FOR PART NUMBERS AND LOCATIONS.
VOLTAGE SELECTION:
Rotate the PLATTER (2) until the VOL TAGE SELECTOR (3) (located on
the TURNTABLE BASE (1)) is visible through one of the platter holes.
Make sure that the VOLTAGE SELECTOR (3) switch is set to the cor-
rect voltage.
WARNING: IF YOU TRYTO OPERA TE THE TURNTABLE WITH THE INCORRECT VOLTAGE
SETTING, IT CAN DAMAGE YOUR TURNTABLE.
ATTACHING THE TURNTABLE BELT:
The TURNTABLE BELT (4) comes attached to the underside of the
PLATTER (2) and the MOTOR SPINDLE (5) but can some times detach
in shipping. Rotate the PLATTER (2) and look through the platter holes
to check if belt detached. If the belt is not wrapped tightly around the
platter and the MOTOR SPINDLE (5), you need to reattach it.
1. Remove the platter and wrap the belt around the inner circle under the
platter. DO NOT STRETCH OUT THE BELT!
HEADSHELL INSTALLATION:
Insert the HEADSHELL (7) into the front of the tubular TONE ARM (9).
While holding the HEADSHELL (7) firmly in a horizontal position, turn
the LOCKING NUT (8) counter clockwise until the HEADSHELL (7) is
locked in place.
COUNTERWEIGHT INSTALLATION: (SEE FIG. 2)
1. Slide the COUNTERWEIGHT (10) onto the rear of the TONE ARM (9)
with the numbered stylus gauge facing forward.
2. Twist the COUNTERWEIGHT (10) counter clockwise lightly, to screw
it onto the rear of the TONE ARM (9).
ADJUSTING HORIZONTAL ZERO (0) BALANCE
AND STYLUS PRESSURE:
1. Without touching the stylus tip, remove the stylus protector (if your
cartridge has a detachable one).
2. Release theARM CLAMP (12) and lift the TONE ARM(9) off the ARM
REST (13).
3. Counter clockwise advancement of the COUNTERWEIGHT (10) will
cause the cartridge side of the TONE ARM (9) to be lowered; turning it
clockwise will cause the opposite. Turn the COUNTERWEIGHT
(10)clockwise or counter clockwise as needed until the TONE ARM (9)
is balanced horizontally. You can easily tell this by watching for the point
where the TONE ARM (9) “floats” freely.
4. Place TONE ARM (9) on ARM REST (13) and lock it in place with the
ARM CLAMP (12).
5. With the TONE ARM (9) locked on the ARM REST (13), hold the
COUNTERWEIGHT (10) steady with one hand while rotating the STYLUS PRESSURE RING (11) until the numeral “0” on the ring aligns with
the center line on the TONE ARM (9) rear shaft. The horizontal zero (0)
balance should be completed.
(44)
6. Re-float the TONE ARM (9) to ensure horizontal zero (0) balance. If
zero balance has not been maintained, repeat counterweight steps 3 - 5.
6. Push the START/STOP (17) button. The turntable PLATTER (2) will
start to spin.
7. After adjusting the horizontal zero (0) balance, turn the balanced
COUNTERWEIGHT (10) counter clockwise until the cartridge manufacturer’s recommend stylus pressure appears on the STYLUS PRES-
SURE RING (11) where it meets the center line of the TONE ARM (9)
rear shaft.
ADJUSTING THE ANTI-SKATING CONTROL:
Set the ANTI-SKATING CONTROL (14) to the same value as the stylus
pressure.
NOTE: IF YOUR TURNTABLE CAME WITH A CN-1000 CARTRIDGE, IT HAS A RECOMMENDED TRACKING FORCE OF 3.0 GRAMS AND CAN HAVE RANGE FROM 2.5-3.5
GRAMS.
CONNECTIONS:
1. Plug the AC power plug into an appropriate outlet.
2. See Table A for proper connection of the output RCA plugs and
ground connector. Make sure that all the plugs are firmly plugged into the
appropriate jacks (phono inputs).
NOTE : TO REDUCE HUM, MAKE SURE THE GROUND LUG IS FIRMLY CONNECTED TO
THE GROUND SCREW.
TABLE A:
OUTPUT CONNECTORS MIXER OR RECIEVER
L (WHITE) PHONO L CHANNEL
R (RED) PHONO R CHANNEL
GND (SPADE LUG) GND SCREW
OPERATING INSTRUCTIONS:
BASIC OPERATION:
1. Place a record on the SLIPMAT (6) which sits on the PLATTER (2).
2. Select the desired speed by depressing the 33 or 45 SPEED SELEC-
TOR (18) button.
3. Turn the POWER (15) switch to the “ON” position, at which point the
TARGET LIGHT (16) will light up, TARGET LIGHTS are an optional
accessory available at your local retailer.
7. Carefully position the tone arm over the desired position over the
record. Lower the TONE ARM (9) slowly, while letting go of the TONE
ARM (9) over the record where you want to play.
8. When play is over, raise the TONE ARM (9), move it onto the ARM
REST (13), and secure it with the ARM CLAMP (12).
9. You now have the option of turning off the power by turning the
POWER (15) switch to the “OFF” position, or stopping the PLATTER (2)
by pushing the START/STOP (17) button.
INTERRUPTING PLAY:
1. Pushing the START/STOP (17) button will cause the record to stop
exactly when the START/STOP (17) button is pressed while playing.
2. Press the START/STOP (17) button again to start playback with a
short DELAY effect.
ADJUSTING THE PITCH CONTROL:
1. The TT-01MKII is equipped with a PITCH CONTROL (19). When the
PITCH CONTROL (19) is in the center position, the speed will be 33 or
45 depending on which SPEED SELECTOR (18) button is pushed.
2. When the PITCH CONTROL (19) is positioned off center, the pitch
can vary ±10% depending on the position of the PITCH CONTROL (19).
SPECIFICATIONS:
TURNTABLE SECTION:
Type..................................................................Belt Drive Manual Turntable
Drive Method.................................................................................Belt Drive
Motor..............................................................................................DC Motor
Speed................................................................................33 1/3 or 45 RPM
Wow and Flutter...................................................Less than 0.25% WRMS*
*THIS RATING REFERS TO THE TURNTABLE ASSEMBLY AND PLATTER ONLY AND
EXCLUDES EFFECTS OF RECORDS, CARTRIDGES OR TONEARMS.
TONEARM SECTION:
Type....................................................Statically Balanced Straight Tonearm
Headshell Weight..................................................................................5.6 g
4. Remove the stylus protector (if applicable to your cartridge).
5. Release the ARM CLAMP (12) found on the ARM REST (13).
GENERAL:
Power Supply................................................AC 115 V~60 Hz/230 V~50 Hz
Power Consumption................................................................................5 W
Dimensions.....................................................................17.75" x 5.75" x 14"
....................................................................................(450 x 136 x 352 mm)
Weight....................................................................................8 lbs. (3.75 kg)
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. THE WEIGHT AND
DIMENSIONS SHOWN ARE APPROXIMATE.
(5)
Loading...