Note: 120V and 230V units have different types of output
connectors on the rear panel.
Input Section:
There are two parallel input connectors (one female XLR and one
1/4” jack) per channel. Either can be used as an input or as a link to
chain amplifiers.
XLR Input Jacks (1, 5): electronically balanced inputs accept a
standard XLR male connector. Pin 1 = shield/ground, pin 2 = hot or
positive (+) and pin 3 = cold or negative (-).
1/4" Phone Input Jacks (2, 4): accept a balanced as well as an
unbalanced line level signal. The unbalanced line uses a standard
tip-sleeve connection. The tip is positive and the sleeve is negative/
ground. The balanced line uses a tip-ring-sleeve connection. Tip =
hot or positive (+), ring = cold or negative (-), and sleeve = shield/
ground.
Operation Mode Switch (3): switch is used to set the unit for Stereo
mode, Parallel Mono mode or Mono Bridge mode.
AC Power Section:
Fuse (7): replace fuse with those of proper type and rating.
Signal Ground Lift Switch (8) is used to lift the balanced input
connectors’ ground/shield from the amplifier’s ground. When the
signal ground lifted, the sound source disconnects from the
amplifier’s ground preventing ground loops which can generate hum
and noise. See the Signal Ground Lift Switch Instructions for more
detail.
AC Cord Outlet (6) (Note: 230V units only) is used to attach the
power cord to the unit.
Output Section:
Disconnect the unit from the AC power source before making any
connections. Pay close attention to polarity (shown on the back of the
unit) when connecting your speakers. Connecting your speaker
systems using the wrong polarity will not damage your speakers, but it
will impact the quality of the sound (lack of bass and incorrect stereo
image).
Speaker Outputs for 120V Unit (9, 10, 11): the speaker output jacks
are 5-way binding posts that will accept a standard banana plugs,
spade lugs or bare wire. Make sure that all the connections are
clean when using bare wire connections. If any strands of wire
from one connector touch the adjacent connector, the sound will be
distorted, and your amplifier will overheat and go into protection
mode.
Speaker Outputs for 230V Unit (9, 10, 11): Neutrik Speakon
connectors are provided to connect speakers to the amplifier quickly
and easily. They are high current rated and provide very stable and
durable contacts. A third Speakon connector in the center is
provided to be used if the amplifier is in the Mono Bridge mode. Every
Speakon connector has pin 1- as negative and pin 1+ as positive.
NOTE: Total speaker impedance must not be lower than 2
Ohm per channel for Stereo and Parallel Mono modes, or 4
Ohm for Mono Bridge mode.
The XPB amplifier is designed to handle low impedence
loads and will operate normally with most 2 ohm
speakers/parallel speaker combinations. However, for
optimal performance and reliability we recommend using
speakers with higher impedence.
Front Panel
Power Switch (20): turns the unit on and off.
Power LED (19): the power LED lights when the power is on. If the
power LED does not light, refer to the trouble shooting guide.
Mono LED (12): the mono LED will light when you have set the rear
panel Operation Mode Switch (3) for parallel mono operation.
Always make sure that this switch is in the correct position and that
all speaker connections have been made correctly for the mode of
operation you wish to use before powering up the amplifier.
Bridge LED (13): the bridge LED will light when you have set the rear
panel Operation Mode Switch (3) for mono bridge operation.
Always make sure that this switch is in the correct position and that
all speaker connections have been made correctly for the mode of
operation you wish to use before powering up the amplifier.
Signal LED (14): the signal LEDs for each channel show when a signal
is present. In Mono Bridge mode, both the channel A LED and the
channel B LED will light in unison.
Clip LED (15): the amplifier has true clip LEDs to help you properly
control the amplifier’s output and achieve undistorted sound. The clip
LEDs for each channel light when your signal level is so strong that
the distortion reaches 1% THD. The clip LED should not remain
constantly on or flash repeatedly during operation. For clean sound
reproduction, the clip should only light occasionally for an instant. If
the LED remains on or flashes repeatedly, you will hear distorted
sound that can be damaging to your speaker systems. If this occurs,
reduce the signal level by lowering the input level control for the
channel that is clipping or reduce the level at the source. If the clip
LED lights when no signal is present, it may indicate a RF signal on
the output which may cause damage to speakers (the RF signal will
not be audible). Please note that when you are using the amplifier in
the Mono Bridge mode, both clip LEDs of the bridged channels will
operate simultaneously.
Protect LED (16): when you first turn on the amplifier, the protect LEDs
light briefly during a turn-on delay which indicates that the outputs
are disconnected internally. There will be an audible click when the
outputs reconnect and the protect LEDs will turn off. Otherwise, the
protect LED indicates that there is a problem either in the amplifier’s
external connections, load or temperature conditions or its internal
functions. If one of these situations occur, the amplifier senses the
problem and automatically switches into protection mode. The LED
will light to warn you of the trouble and the amplifier will stop
working. If this occurs, switch off the amplifier and refer to the
Trouble Shooting Guide. If the protect LED remains lit when resuming
amplifier operation, do not use the amplifier and contact an
authorized service technician.
Level Controls (17, 18): establish the input levels required for each
channel. Only the Channel A Level Control (17) works in Mono
Bridge mode.
Operating Instructions
THE AMPLIFIER’S POWER MUST BE TURNED OFF WHEN
CHANGING MODES OF OPERATION.
Stereo Operation
The unit has two channels for stereo operation. Each channel
provides a separate and discrete signal at the speaker outputs
according to the signal received at the inputs. The following instructions
are for applications with 8 Ohm, 4 Ohm or 2 Ohm speakers of matched
power ratings.
1. With the power off, set the OPERATION MODE SWITCH (3) to the
STEREO position. When the power is on, the Mono and Bridge LEDs
on the front panel will not light. If these LEDs illuminate, you have the
switch in the wrong position. Correct before continuing.
2. With the power off, connect your input cables to the channel A and
B inputs using either the XLR INPUT JACKS (1, 5) or 1/4" INPUT
JACKS (2, 4) of each channel. The other channel A and channel B
inputs can be used to link to an additional amplifier.
3. Connect the loudspeakers to the channel A and channel B SPEAKER
OUTPUTS (9, 11). THE T OT AL SPEAKER LOAD MUST BE A T LEAST
2 OHMS PER CHANNEL. If you try to operate at a lower impedance,
the amplifier will go into protection mode and stop operation until you
correct the load conditions.
4. With the LEVEL CONTROLS (17, 18) of both channels set to zero
(fully counterclockwise), turn the POWER SWITCH (20) on. Apply a
signal to the input of the amplifier. The level of the input signal should
(4)
Page 5
be as high as you will ever need it to be. This way, it will be as high
above the amplifier’s noise floor as possible, ensuring an excellent
performance and signal to noise ratio. Adjust the LEVELCONTROLS for each channel to achieve the desired maximum
listening level. Note, when the clip LEDs light, there is distortion
present in the amplifier’s output section. If a clip LED remains on or
flashes repeatedly, reduce the signal level by lowering the input level
control for the channel that is clipping or reduce the level at the
source.
Parallel Mono Operation
Follow these instructions for Parallel Mono Operation using a single
input cable, and you will have the same monophonic signal on both the
channel A and the channel B outputs. Each channel’s output is
controlled independently by that channel’s level control.
1. With the power off, set the OPERATION MODE SWITCH (3) to the
PARALLEL MONO position. When the power is on, the MONO LED
(12) on the front panel will light. If the LED does not illuminate, you
have the switch in the wrong position. Correct before continuing.
2. With the power off, connect your input cables to the channel A input
only using the either the XLR INPUT JACK (5) or 1/4" INPUT JACK
(4) of channel A. The other channel A input can be used to link to an
additional amplifier.
3. Connect the loudspeakers to the channel A and channel B SPEAKER
OUTPUTS (9, 11). THE T OT AL SPEAKER LOAD MUST BE A T LEAST
2 OHMS PER CHANNEL. If you try to operate at a lower impedance,
the amplifier will go into protection mode and stop operation until you
correct the load conditions.
4. With the LEVEL CONTROLS (17, 18) set to zero (fully
counterclockwise), switch the power on. Apply a signal to the input.
The level of the input signal should be as high as you will ever need
it to be. This way, it will be as high above the amplifier’s noise floor
as possible, ensuring an excellent performance and signal to noise
ratio. Adjust the LEVEL CONTROLS for each channel to achieve the
desired maximum listening level. Note, when the clip LEDs light, there
is distortion present in the amplifier’s output section. If a clip LED
remains on or flashes repeatedly, reduce the signal level by lowering
the input level control for the channel that is clipping or reduce the
level at the source.
desired maximum listening level. Note, when the clip LEDs light, there
is distortion present in the amplifier’s output section. If a clip LED
remains on or flashes repeatedly, reduce the signal level by lowering
the input level control for channel A or reduce the level at the
source. During Mono Bridge operation, the channel B level is
inactive, however, both channels LEDs will flash simultaneously and
show output conditions.
Using the Signal Ground Lift Switch
Depending on your system configuration, sometimes applying the
ground will create a quieter signal path. Sometimes lifting the ground
can eliminate ground loops and hum to create a quieter signal path.
1. With the power amp on, listen to the system in idle mode (no signal
present) with the ground applied (the SIGNAL GROUND LIFT
SWITCH (8) in the left position).
2. Then turn the power off before moving the SIGNAL GROUND
LIFT SWITCH (8). Lift the ground by moving the SIGNAL GROUND
LIFT SWITCH to the right, turn the power back on and listen to
determine which position will provide a signal devoid of background
noise and hum. Keep the SIGNAL GROUND LIFTSWITCH in the
ground position if the noise level remains the same in either position.
CAUTION: DO NOT TERMINATE THE AC GROUND ON THE POWER
AMPLIFIER IN ANY WA Y . TERMINA TION OF THE AC GROUND CAN BE
HAZARDOUS.
Mono Bridge Operation
Follow these instructions to bridge the unit’s outputs. Bridging the
amplifier converts the unit to a monophonic or single channel. The
amplifier can be used with 8 Ohm or higher loads only in Mono Bridge
mode. This mode is used to provide a higher voltage with greater
headroom to your speaker. Before setting your amplifier for Mono Bridge
operation, make sure that your speaker can handle the high power level
provided by the amplifier in Mono Bridge mode. CAUTION: VOL TAGE
OVER 100 VOLTS MA Y BE PRODUCED A T THE BRIDGE OUTPUT
TERMINALS IN THIS MODE.
1. With the power off, set the OPERATION MODE SWITCH (3) to the
BRIDGE position. When the power is on, the BRIDGE LED (13) on
the front panel will light. If the LED does not illuminate, you have the
switch in the wrong position. Correct before continuing.
2. With the power off, connect your input cables to channel A input
only using the either the XLR INPUT JACK (5) or 1/4" INPUT JACK
(4) of channel A. The other channel A input can be used to link to an
additional amplifier.
3. Connect the loudspeaker to the BRIDGE SPEAKER OUTPUT (10)
only. With a 230V unit, use the center speakon. With a 120V unit,
use the two innermost red terminals. Be sure the polarity of your
connections is correct. The total speaker load must be at least 4
Ohms or above. If you try to operate at a lower impedance, the
amplifier will go into protection mode and stop operation until you
correct the load conditions.
4. With the CHANNEL A LEVEL CONTROL (17) set to zero (fully
counterclockwise), switch the power on. Apply a signal to the input.
The level of the input signal should be as high as you will ever need
it to be. This way, it will be as high above the amplifier’s noise floor
as possible, ensuring an excellent performance and signal to noise
ratio. Adjust the LEVEL CONTROL (17) for channel A to achieve the
(5)
Page 6
SYMPTOMCAUSESOLUTION
UNIT DOES NOT PRODUCE SOUND. POWER LED
DOES NOT LIGHT.
POWER LED LIGHTS, BUT NO SOUND IS
PRODUCED BY AMPLIFIER.
SOUND IS PRESENT BUT VOLUME IS TOO LOW
EVEN THOUGH SOURCE DEVICE IS SET TO A HIGH
LEVEL.
LOUD 50/60 HZ OR 100/120 HZ HUM IS HEARD AT
ALL TIMES THROUGH THE SPEAKER SYSTEMS.
• POWER SWITCH NOT IN ON POSITION.
• POWER CABLE NOT CONNECTED TO AMPLIFIER
OR TO OUTLET.
• AC OUTLET NOT ACTIVE.
• MAIN AMPLIFIER FUSE DEFECTIVE.
• NO INPUT SOURCE SIGNAL.
• INPUT SOURCE NOT CONNECTED.
• INPUT CONNECTING CABLE DEFECTIVE.
• SPEAKER(S) NOT CONNECTED.
• SPEAKER CABLE DEFECTIVE.
• SPEAKER SYSTEM(S) INOPERATIVE.
• AMPLIFIER’S LEVEL CONTROLS ARE SET TO
ZERO.
• AMPLIFIER INPUT LEVEL CONTROLS ARE SET
TOO LOW.
• WRONG PIN CONNECTIONS IN CABLES.
• IMPROPER OR DEFECTIVE GROUND
CONNECTION AT INPUTS. IMPROPER OR
DEFECTIVE GROUND AT INPUT SOURCE DEVICE(S).
• IMPROPER OR DEFECTIVE GROUND
CONNECTION ON AC OUTLET.
• GROUND LOOP THROUGH AC LINE CONNECTION/
RACK MOUNTING.
• MOVE POWER SWITCH TO ON POSITION.
• CONNECT POWER CABLE TO AC SUPPLY.
• CHECK CONDITION OF OUTLET.
• REPLACE AMPLIFIER MAIN POWER FUSE ON REAR PANEL WITH CORRECT
TYPE AND RATING.
• CHECK FOR PROPER FUNCTION OF INPUT SOURCE DEVICE.
• CHECK INPUT CABLES AND CONNECTIONS. REPLACE QUESTIONABLE
CABLES WITH KNOWN GOOD CABLES.
• CHECK SPEAKER CABLES AND CONNECTIONS. REPLACE QUESTIONABLE
CABLES WITH KNOWN GOOD CABLES.
• CHECK OPERATING CONDITION AND STATUS OF SPEAKER SYSTEM(S). BE
SURE THE LEVEL CONTROLS ARE PROPERLY SET.
• ADJUST LEVEL CONTROLS AS PER INSTRUCTIONS.
• USE CORRECT CABLES (AS SHOWN ON BACK OF UNIT).
• CHECK FOR PROPER AC LINE GROUND ON POWER AMP AND ALL INPUT
DEVICES.
• CHECK INPUT CABLES FOR ALL SOURCE DEVICES AND SIGNAL
PROCESSING AS WELL AS INPUT CABLES TO POWER AMPLIFIER. CHECK
POSITION OF GROUND LIFT SWITCH AS PER INSTRUCTIONS FOR LIFTING
THE GROUND.
• NEVER LIFT THE AC LINE GROUND ON THE POWER AMPLIFIER. IF YOU
ARE NOT TOTALLY FAMILIAR WITH GROUND LIFTING OR UNIFICATION
PROCEDURES, DO NOT ATTEMPT THEM WITHOUT FIRST CONSULTING
YOUR DEALER OR A QUALIFIED SOUND TECHNICIAN FOR MORE
INFORMATION ON GROUNDING. IMPROPERLY DONE, SUCH PROCEDURES
CAN POSE A SAFETY AND/OR FIRE HAZARD.
SOUND IS DISTORTED.
PROTECT LED REMAINS LIT OR GOES ON AND
OFF INTERMITTENTLY AFTER USING AMPLIFIER
FOR A SHORT TIME.
FUSE BLOWS INTERMITTENTLY.
PROTECT LED(S) STAY ON WITH NO SPEAKERS
CONNECTED AND WITH THE AMPLIFIER COOLED
DOWN.
POWER LED LIGHTS BUT THERE IS NO SOUND
FROM ONE OR BOTH CHANNELS.
• DISTORTION OCCURRING IN SOURCE DEVICE.
• INPUT LEVEL IS SET TOO HIGH.
• UNIT IS OPERATING AT EXCESSIVELY HIGH
TEMPERATURE.
• EXTREMELY LOW SPEAKER IMPEDANCE.
• SHORT IN SPEAKER CONNECTORS, SPEAKER
CABLE OR SPEAKER SYSTEM.
• SPEAKER LOAD IMPEDANCE IS TOO LOW.
• TYPE OR RATING OF THE FUSE IS NOT
CORRECT.
• FAILED AMPLIFIER.
• SECONDARY DC FUSES ARE BLOWN (ON EITHER
ONE OR BOTH CHANNELS INDICATING FAILED A
FAILED CHANNEL OR CHANNELS.
• CHECK CLIP INDICATORS ON INPUT SOURCE DEVICES AND RESET LEVELS
IF NECESSARY TO ELIMINATE DISTORTION.
• ADJUST LEVEL CONTROLS AS PER INSTRUCTIONS.
• CHECK THAT AMPLIFIER IS ADEQUATELY VENTILATED ON THE FRONT
AND REAR PANELS WHERE THE AIR VENTS AND FANS ARE LOCATED. IF
OVERHEATED, LET THE AMPLIFIER COOL DOWN BEFORE APPLYING AN
INPUT SIGNAL.
• CHECK THE POSITION OF OPERATION MODE SWITCH. BE SURE THAT THE
SPEAKER CONNECTIONS ARE MADE IN ACCORDANCE WITH THE SWITCH
SETTING.
• VERIFY SPEAKER SYSTEM IMPEDANCES. BE SURE THE TOTAL SPEAKER
SYSTEM IMPEDANCE IS AT LEAST 4 OHMS PER CHANNEL WHEN THE
OPERATION MODE SWITCH IS IN THE STEREO POSITION OR PARALLEL
MONO POSITION. IF THE SWITCH IS IN THE BRIDGE MODE, THE IMPEDANCE
MUST BE AT LEAST 8 OHMS. IF YOU ARE NOT SURE OF YOUR TOTAL
SPEAKER IMPEDANCE LOAD, CONTACT YOUR DEALER FOR MORE
INFORMATION.
• CHECK CONDITION OF SPEAKER CABLES.
• IF USING BARE WIRE CONNECTIONS ON THE OUTPUTS OF THE AMPLIFIER,
BE SURE THAT NO STRANDS FROM ONE CONNECTOR ARE TOUCHING
ANY OTHER CONNECTOR.
• CHECK FOR SHORTS ON THE OUTPUTS.
• CHECK YOUR SPEAKER IMPEDANCE (INFO FROM DEALER).
• CHECK THAT THE FUSE TYPE AND RATING IS CORRECT.
• CONTACT THE GEMINI SERVICE DEPARTMENT OR YOUR AUTHORIZED
DEALER TO SPEAK TO A QUALIFIED SERVICE TECHNICIAN.
• IF ONLY ONE CHANNEL FAILS, THE SECOND MAY STILL OPERATE, BUT
THE UNIT SHOULD BE SERVICED AS SOON AS POSSIBLE. CONTACT THE
GEMINI SERVICE DEPARTMENT OR YOUR AUTHORIZED DEALER TO SPEAK
TO A QUALIFIED SERVICE TECHNICIAN.
(6)
Page 7
Specifications
Output Power EIA: 1 kHz @ 1% THD
Single Channel 8Ω190340
Both Channels Driven 8Ω175300
Single Channel 4Ω325600
Both Channels Driven 4Ω275500
Single Channel 2Ω470950
Both Channels Driven 2Ω360800
Mono Bridge 8Ω5501000
Mono Bridge 4Ω7501600
Dynamic Headroom:
8Ω1.31.3
4Ω2.32.1
Frequency Response............................................................20 Hz - 20 kHz
Total Harmonic Distortion...............................less than 0.01% @ 1 kHz
Intermodulation Distortion.......................less than 0.02% (SMPTE)
Signal to Noise Ratio..........................100 dB below rated power @ 8Ω
Damping Factor (XPB-750)........................greater than 500 @ 8Ω
Damping Factor (XPB-1600)..............................greater than 800 @ 8Ω
Speaker Outputs (230V unit)...........Speakons (ch.A, ch.B and bridge)
Dimensions...................................19" x 13.75" x 3.5" (483 x 350 x 89 mm)
WeightXPB-750XPB-1600
* Specifications and design are subject to change without notice for
purpose of improvement.
XPB-750XPB-1600
XPB-750XPB-1600
XPB-750XPB-1600
0.82 VRMS1.1 VRMS
550 VA1000 VA
230V/ 50 Hz
1 Signal LED per channel
1 Clip LED per channel
1 Protect LED per channel
1 Mono LED
1 Bridge LED
27 lbs34 lbs
12.34 kg15.5 kg
(7)
Page 8
PARTS LISTS:
Vendor Part #: Description: Quantity:Vendor Part #: Description: Quantity:
1) 102056543301
2) 102119214705
3) 102260018005
4) 103012005700
5) 105011108801
6) 105032408401
7) 105034608801
8) 105343431801
9) 105443431702
10) 1070KG-010—
11) 1070YJ-98—-
12) 105242608607
13) 107022———
14) AB7N-2———
15) AC2016014R3C
16) 1070P0.86401
17) 106219207603
18) 1070SS-6——
19) 2SA1943O—0
20) 2SC5200O—0
21) 2SA1015GR—T
22) 2SC1815GR—T
23) 6003501952—
24) 70000SF14051
25) 700033050001
26) 700082050001
27) 700150050001
28) 700150100001
29) 7001N4004051
30) 7001N4148051
31) MPMSC104100J
32) MPMSC105063J
33) RC0030A33005
34) RC0031000005
35) RC0031010005
36) RC0031020005
37) RC0031030005
38) RC0031040005
39) RC0031320005
40) RC0031520005
41) RC0031610005
42) RC0032020005
43) RC0032230005
44) RC0032240005
45) RC0032430005
46) RC0033010005
47) RC0033030005
48) RC0033040005
49) RC0033310005
50) RC0033610005
51) RC00351 10005
52) RC0038220005
53) RC0034740005
54) RC0050A10005
55) RC0053030005
56) RM003001M001
57) RM00301K2001
58) RM00301K9101
59) RM00302K2101
60) RM0030A12101
61) RM0030A15001
62) RM00310K0001
63) RM0031 10K001
64) RM00313K0001
65) RM00324K3001
66) RM00368K0001
67) RM00516K5001
68) TRMPSA42—0
69) TRMPSA92—0
70) 105006400001
71) 106203003003
72) 1070LEDS-6.5
73) 7001N5404051
74) 700KBP060002
75) 700MP3504W02
76) CCN0A101 100K
77) CCZ0A100500K
78) CCZ0A103500Z
79) CCZ0A220500K
80) CCZ0A271025K
81) CCZ0A330100K
82) CCZ0A680500K
83) COIL20105T—
84) ECL04700080M
85) ECS00100025M
XPB-750 120vXPB-1600 120v
SPACER XPM-900
CARTON XPB-750
EXT .CARTON XPB-750
SPACER 1200x570m/m
HOLDER XPB-1600
WALL XPB-1600
SLID PANEL XPB-1600
TOP COVER XPM-900
BOTTOM CABI XPB-1600
M0VEABLE BUSHING KG-010
NYLON CLAMPER YJ-98
XPB-750 BACK BOARD 120V
TUBE 22 m/m XPB-1600
AC BUSHIN 7N-2
AL-201 SJT W-A 14AWGx3C 6FT
TUBE 0.864 BLACK
HEAT SINK 192x76x60 XPB-1600
SELF RETA TINING SP ALERS SS-6
TR 2SA1943-O
TR 2SC5200-O
TR 2SA1015GR T
TR 2SC1815GR T
XPB-1600 MAIN PC BOARD T=2oz
DIODE SF14
ZENER 3.3v 500mw
ZENER 8.2V 500mw
ZENER 15V 500mw
ZENER 15V 1W
DIODE 1N4004
DIODE 1N4148
MSC .1u 100V 5% T
MSC 1u 63V SC105J1J T
RESISTORS 3.3 ohm 1/4W T
RESISTORS 10 ohm 1/4W T
RESISTORS 100 ohm 1/4W T
RESISTORS 1 K 1/4W T
RESISTORS 10 K 1/4W T
RESISTORS 100 K 1/4W T
RESISTORS 1.3 K 1/4W T
RESISTORS 1.5 K 1/4W T
RESISTORS 160 ohm 1/4W T
RESISTORS 2 K 1/4W T
RESISTORS 22 K 1/4W T
RESISTORS 220 K 1/4W T
RESISTORS 24 K 1/4W T
RESISTORS 300 ohm 1/4W T
RESISTORS 30 K 1/4W T
RESISTORS 300 K 1/4W T
RESISTORS 330 ohm 1/4W T
RESISTORS 360 ohm 1/4W T
RESISTORS 510ohm 1/4W T
RESISTORS 8.2 K 1/4W T
RESISTORS 470 K T
RESISTORS 1 ohm 1/2W T
RESISTORS 30 K 1/2W T
RESISTORS 1M 1% 1/4W T
RESISTORS 1.2K 1% 1/4W T
RESISTORS 1K91 1% 1/4W T
RESISTORS 2.21K 1% 1/4W T
RESISTORS 121 ohm 1% 1/4W T
RESISTORS 150 ohm 1% 1/4W T
RESISTORS 10K 1% 1/4W T
RESISTORS 110K 1% 1/4W T
RESISTORS 13K 1% 1/4W T
RESISTORS 24K3 1% 1/4W T
RESISTORS 68 K 1% 1/4W T
RESISTORS 16K5 1% 1/2W T
TR MPSA42
TR MPSA92
6.4m/m PIN (805551-BL2)
RECTIFER HEA T SINK XPB-1600
LED SPACER SUPPOR T LEDS-6.5
DIODE 1N5404
RECTIFIER KBP06 2A 600V
RECTIFIER MP3504W 35A 400V
CERAMIC CAP 100P 100V
CERAMIC CAP 10P 500V NPO
CERAMIC CAP 103 500V
CERAMIC CAP 22P/500V NPO
CERAMIC CAP 270P
CERAMIC CAP 33P/100V
CERAMIC CAP 68P/500V NPO
COIL 2.0x10x10.5t XPB-750
ELEC CAP 4700u80v
ELEC CAP 100u25v
SPACER XPM-900
CARTON XPB-1600
EXT.CARTON XPB-1600
SPACER 1200x570m/m PA1000
HOLDER XPB-1600
WALL XPB-1600
SLID PANEL XPB-1600
TOP COVER XPM-900
BOTTOM CABI XPB-1600
CARD BOARD 182x65x1t BLACK
M0VEABLE BUSHING KG-010
NYLON CLAMPER YJ-98
XPB-1600 BACK BOARD 12OV
TUBE 22 m/m XPB-1600
AC BUSHIN 7N-2
AL-201 SJT W-A 14AWGx3C 6FT
TO-92 HEAT SINK XPB-1600
TO-126 HEAT SINK XPB-1600
HEAT SINK 192x76x60 XPB-1600
TUBE 0.864 BLACK
SELF RETATINING SPALERS SS-6
TR 2SA1943-O
TR 2SC5200-O
TR 2SA1015GR T
TR 2SC1815GR T
XPB-1600 MAIN PC BOARD T=2oz
DIODE SF14
ZENER 3.3v 500mw
ZENER 8.2V 500mw
ZENER 15V 500mw
ZENER 15V 1W
DIODE 1N4004
DIODE 1N4148
MSC .1u 100V 5% T
MSC 1u 63V SC105J1J T
RESISTORS 3.3 ohm 1/4W T
RESISTORS 10 ohm 1/4W T
RESISTORS 100 ohm 1/4W T
RESISTORS 1 K 1/4W T
RESISTORS 10 K 1/4W T
RESISTORS 100 K 1/4W T
RESISTORS 1.3 K 1/4W T
RESISTORS 1.5 K 1/4W T
RESISTORS 160 ohm 1/4W T
RESISTORS 2 K 1/4W T
RESISTORS 22 K 1/4W T
RESISTORS 220 K 1/4W T
RESISTORS 24 K 1/4W T
RESISTORS 300 ohm 1/4W T
RESISTORS 30 K 1/4W T
RESISTORS 300 K 1/4W T
RESISTORS 330 ohm 1/4W T
RESISTORS 360 ohm 1/4W T
RESISTORS 510ohm 1/4W T
RESISTORS 8.2 K 1/4W T
RESISTORS 1.5 M 1/4W T
RESISTORS 1 ohm 1/2W T
RESISTORS 30 K 1/2W T
RESISTORS 1M 1% 1/4W T
RESISTORS 1.2K 1% 1/4W T
RESISTORS 1.3K 1% 1/4W T
RESISTORS 2.21K 1% 1/4W T
RESISTORS 121 ohm 1% 1/4W T
RESISTORS 150 ohm 1% 1/4W T
RESISTORS 162 ohm 1% 1/4W T
RESISTORS 10K 1% 1/4W T
RESISTORS 110K 1% 1/4W T
RESISTORS 24K3 1% 1/4W T
RESISTORS 40K2 1% 1/4W T
RESISTORS 68 K 1% 1/4W T
RESISTORS 23K2 1% 1/2W T
TR MPSA42
TR MPSA92
6.4m/m PIN (805551-BL2)
RECTIFER HEAT SINK XPB-1600
LED SPACER SUPPORT LEDS-6.5
DIODE 1N5404
RECTIFIER KBP06 2A 600V
RECTIFIER MP3504W 35A 400V
CERAMIC CAP 100P 100V
CERAMIC CAP 10P 500V NPO
CERAMIC CAP 103 500V
CERAMIC CAP 22P/500V NPO
CERAMIC CAP 270P
CERAMIC CAP 33P/100V
CERAMIC CAP 68P/500V NPO
COIL 2.0x10x10.5t XPB-1600
ELEC CAP 6800u100v
ELEC CAP 100u25v
ELEC CAP 220u16v
ELEC CAP 220u25v
ELEC CAP 220u16v
ELEC CAP 220u25v
ELEC CAP 1000u25v
ELEC CAP 2200u25v
FUSE CLIP CQ-203SC
FUSE 5x20 8A
IC NJM3404AD
ICTL071CP
IC TL072CP
BASE 3P 2.5m/m
BASE 7P 2.5m/m
BASE 2P JS-1001R-02
LED 5m/m GREEN
LED 5m/m RED
LED 5m/m YELLOW
CONNOC JACK 086-25-90
JACK CPJ-065 XPM-900
MEF .1u 250V 10%
NUT 3m/m W/S (0J0010-030001)
RESISTORS 2 ohm 2W M
RESISTORS 6.8 K 2W M
RESISTORS 2.7 ohm 3W M
832-1C-C-12D XPM-900
1.2 K 5W SQT TYPE
0.22 ohm 5W SOT TYPE
MS 3x8 (1JPHMC-030800)
TP4x20 (1JBH6C-042021)
SS004-P2430Em-PC10 XPM-900
SS004-P022 BY-PF8
MJE340
MJE350
TR MPSA13
TIP122
TRIAC Z0103 MA1A600V RR-15
1015#14 5/130/5 GREEN XPB-1600
1015#14 GREEN XPM-900
1015x14 5/160/5 BROWN XPB-1600
1015#14 5/170/20 GRAY XPB-1600
1015#14 GREEN XPM-900
1015#14 5/320/20 RED XPB-1600
1007#26 MIX XPB-1600
SPRING W/S.M4-L(2JS100-040050)
PTH9M04BE222TS2F333 XPM-900
PTH9M04BH471TS2F333 XPM-900
MS 3x12 BLACK
FMT+W TP 4x8 (1JBP6C-040825)
3.2x0.8x10 (2IFA032-081000)
SPRING W/S.M3-L(2JS100-030050)
XPB-1600 83x38 m/m P .BOARD 2o
NTC 20A SCK-0120 XPM-900
1015#14 250R+360/5m/m BLACK
1015#14 250R+440/5m/m WHITE
1015#14 BLACK XPM-900U
FUSE HOLD CQ-207D
FUSE 6x30 FAST/CERAMIC U/C 12A
WIN-1047R2 R/B XPM-900
WTN-1047R2 B/R XPM-900
WIN-1047R2 COVER BLACK XPM-900
WIN-1047R2 COVER RED XPM-900
MS 3x6 BLACK(1JBHMC-030604)
MS 4x6 (PLA TING)
TP 3x10 BLACK (1JBHCC-031024)
EXT TOOTH W/S. 4m/m
LABEL 8 m/m (GND)
FRONT PANEL XPB-750
KNOB 18x19 BLACK XPM-900
TP 3x6 BLACK (1JBHCC-030625)
R22-22B-11B XPM-900
16K4x1 10Ax1 41K L-15 XPM-900
2852#26 RED XPM-900
2852#26 GRAY XPM-900
SP802512H L=350m/m+XH
PLASTIC FOOT SF-006
MANUAL XPB-1600 (GEMINI)
NUT 5/16 (0A0220-310005)
PLOY BAG 8.5"x16.5"X0.05
TRANS. 120m/m XPB-750 120V
MS 3x8 (1JPHMC-030800)
MS 3x12 BLACK
MST 4x8 BLACK (1JBH1C-040824)
TP 3.5x8 (1JPH6C-3F0824)
TP 3x6 BLACK (1JBHCC-030625)
FMT+W TP 4x8 (1JBP6C-040825)
5/16x3" (1ATKMO-31C004)
GEMINI WARRANTY CARD
EXT TOOTH W/S. 3m/m
LABEL 6 m/m (VLOT)
ELEC CAP 1000u25v
ELEC CAP 2200u25v
FUSE CLIP CQ-203SC
FUSE 5x20 12A
IC NJM3404AD
ICTL071CP
IC TL072CP
BASE 3P 2.5m/m
BASE 7P 2.5m/m
BASE 2P JS-1001R-02
LED 5m/m GREEN
LED 5m/m RED
LED 5m/m YELLOW
CONNOC JACK 086-25-90 EQ-15x2
JACK CPJ-065 XPM-900
MEF .1u 250V 10%
NUT 3m/m W/S (0J0010-030001)
RESISTORS 2 ohm 2W M
RESISTORS 6.8 K 2W M
RESISTORS 2.7 ohm 3W M
832-1C-C-12D XPM-900
2.2 K 5W SQT TYPE
0.33 ohm 5W SQT TYPE
MS 3x8 (1JPHMC-030800)
TP4x20 (1JBH6C-042021)
SS004-P2430Em-PC10 XPM-900
SS004-P022 BY-PF8 V2000
MJE340
MJE350
TR MPSA13
TIP122
TRIAC Z0103 MA1A600V RR-15
1015#14 5/70/5 RED XPB-1600
1015#14 5/70/5 GRAY XPB-1600
1015#14 5/70/5 WHITE XPB-1600
1015#14 5/130/5 GREEN XPB-1600
1015#14 GREEN XPM-900
1015x14 5/160/5 BROWN XPB-1600
1015#14 5/170/20 GRAY XPB-1600
1015#14 GREEN XPM-900
1015#14 5/320/20 RED XPB-1600
1007#26 MIX XPB-1600
SPRING W/S.M4-L(2JS100-040050)
TR PC BOARD 171x42 m/m 2oz
MEF .1u 250V 10%
RESISTORS 3.3 ohm 1/4W T
0.33 ohm 5W SQT TYPE
PTH9M04BE222TS2F333 XPM-900
PTH9M04BH471TS2F333 XPM-900
MS 3x12 BLACK
FMT+W TP 4x8 (1JBP6C-040825)
3.2x0.8x10 (2IFA032-081000)
SPRING W/S.M3-L(2JS100-030050)
XPB-1600 83x38 m/m P.BOARD 2oz
NTC 20A SCK-0120 XPM-900
1015#14 250R+360/5m/m BLACK
1015#14 250R+440/5m/m WHITE
1015#14 BLACK XPM-900U
FUSE HOLD CQ-207D
FUSE 6x30 FAST/CERAMIC U/C 15A
WIN-1047R2 R/B XPM-900
WTN-1047R2 B/R XPM-900
WIN-1047R2 COVER BLACK XPM-900
WIN-1047R2 COVER RED XPM-900
MS 3x6 BLACK(1JBHMC-030604)
MS 4x6 (PLATING)
TP 3x10 BLACK (1JBHCC-031024)
FMT+W TP 4x8 (1JBP6C-040825)
EXT TOOTH W/S. 4m/m
LABEL 8 m/m (GND)
FRONT PANEL XPB-1600
KNOB 18x19 BLACK XPM-900
TP 3x6 BLACK (1JBHCC-030625)
R22-22B-11B XPM-900
16K4x1 10Ax1 41K L-15 XPM-900
2852#26 RED XPM-900
2852#26 GRAY XPM-900
SP802512H L=350m/m+XH V2000
PLASTIC FOOT SF-006 V2000
MANUAL XPB-1600 (GEMINI)
NUT 5/16 (0A0220-310005)
PLOY BAG 8.5"x16.5"X0.05
TRANS. 160m/m XPB-1600 120V
MS 3x8 (1JPHMC-030800)
MS 3x12 BLACK
MST 4x8 BLACK (1JBH1C-040824)
TP 3.5x8 (1JPH6C-3F0824)
TP 3x6 BLACK (1JBHCC-030625)
FMT+W TP 4x8 (1JBP6C-040825)
5/16x3" (1ATKMO-31C004)V3000
GEMINI WARRANTY CARD
EXT TOOTH W/S. 3m/m
LABEL 6 m/m (VLOT)
Vendor Part #: Description: Quantity:Vendor Part #: Description: Quantity:
1) 102056543301
2) 102119214705
3) 102260018005
4) 103012005700
5) 105011108801
6) 105032408401
7) 105034608801
8) 105343431801
9) 105443431702
10) 1070KG-010—
11) 1070YJ-98—-
12) 105242608608
13) 107022———
14) 107007———
15) 6000800181—
16) AL301AL50101
17) AO016D130—-
18) 1070P0.86401
19) 106219207603
20) 1070SS-6——
21) 2SA1943O—0
22) 2SC5200O—0
23) 2SA1015GR—T
24) 2SC1815GR—T
25) 6003501952—
26) 70000SF14051
27) 700033050001
28) 700082050001
29) 700150050001
30) 700150100001
31) 7001N4004051
32) 7001N4148051
33) MPMSC104100J
34) MPMSC105063J
35) RC0030A33005
36) RC0031000005
37) RC0031010005
38) RC0031020005
39) RC0031030005
40) RC0031040005
41) RC0031320005
42) RC0031520005
43) RC0031610005
44) RC0032020005
45) RC0032230005
46) RC0032240005
47) RC0032430005
48) RC0033010005
49) RC0033030005
50) RC0033040005
51) RC0033310005
52) RC0033610005
53) RC0035110005
54) RC0038220005
55) RC0034740005
56) RC0050A10005
57) RC0053030005
58) RM003001M001
59) RM00301K2001
60) RM00301K9101
61) RM00302K2101
62) RM0030A12101
63) RM0030A15001
64) RM00310K0001
65) RM003110K001
66) RM00313K0001
67) RM00324K3001
68) RM00368K0001
69) RM00516K5001
70) TRMPSA42—0
71) TRMPSA92—0
72) 105006400001
73) 106203003003
74) 1070LEDS-6.5
75) 7001N5404051
76) 700KBP060002
77) 700MP3504W02
78) CCN0A101100K
79) CCZ0A100500K
80) CCZ0A103500Z
81) CCZ0A220500K
82) CCZ0A271025K
83) CCZ0A330100K
84) CCZ0A680500K
85) COIL20105T—
86) ECL04700080M
87) ECS00100025M
88) ECS00220016M
89) ECS00220025M
90) ECS01000025M
XPB-750 230vXPB-1600 230v
SPACER XPM-900
CARTON XPB-750
EXT.CARTON XPB-750
SPACER 1200x570m/m
HOLDER XPB-1600
WALL XPB-1600
SLID PANEL XPB-1600
TOP COVER XPM-900
BOTTOM CABI XPB-1600
M0VEABLE BUSHING KG-010
NYLON CLAMPER YJ-98
XPB-750E BACK BOARD 230V
TUBE 22 m/m XPB-1600
TUBE 7 m/m XPB-1600
SPKON PC BOARD XPB1600E/750E
AL301/AL501 H-05XX-F 1.0m/mX3G
3P AC INLET R-301SN-M XPM-900
TUBE 0.864 BLACK
HEAT SINK 192x76x60 XPB-1600
SELF RETATINING SPALERS SS-6
TR 2SA1943-O
TR 2SC5200-O
TR 2SA1015GR T
TR 2SC1815GR T
XPB-1600 MAIN PC BOARD T=2oz
DIODE SF14
ZENER 3.3v 500mw
ZENER 8.2V 500mw
ZENER 15V 500mw
ZENER 15V 1W
DIODE 1N4004
DIODE 1N4148
MSC .1u 100V 5% T
MSC 1u 63V SC105J1J T
RESISTORS 3.3 ohm 1/4W T
RESISTORS 10 ohm 1/4W T
RESISTORS 100 ohm 1/4W T
RESISTORS 1 K 1/4W T
RESISTORS 10 K 1/4W T
RESISTORS 100 K 1/4W T
RESISTORS 1.3 K 1/4W T
RESISTORS 1.5 K 1/4W T
RESISTORS 160 ohm 1/4W T
RESISTORS 2 K 1/4W T
RESISTORS 22 K 1/4W T
RESISTORS 220 K 1/4W T
RESISTORS 24 K 1/4W T
RESISTORS 300 ohm 1/4W T
RESISTORS 30 K 1/4W T
RESISTORS 300 K 1/4W T
RESISTORS 330 ohm 1/4W T
RESISTORS 360 ohm 1/4W T
RESISTORS 510ohm 1/4W T
RESISTORS 8.2 K 1/4W T
RESISTORS 470 K T
RESISTORS 1 ohm 1/2W T
RESISTORS 30 K 1/2W T
RESISTORS 1M 1% 1/4W T
RESISTORS 1.2K 1% 1/4W T
RESISTORS 1K91 1% 1/4W T
RESISTORS 2.21K 1% 1/4W T
RESISTORS 121 ohm 1% 1/4W T
RESISTORS 150 ohm 1% 1/4W T
RESISTORS 10K 1% 1/4W T
RESISTORS 110K 1% 1/4W T
RESISTORS 13K 1% 1/4W T
RESISTORS 24K3 1% 1/4W T
RESISTORS 68 K 1% 1/4W T
RESISTORS 16K5 1% 1/2W T
TR MPSA42
TR MPSA92
6.4m/m PIN (805551-BL2)
RECTIFER HEAT SINK XPB-1600
LED SPACER SUPPORT LEDS-6.5
DIODE 1N5404
RECTIFIER KBP06 2A 600V
RECTIFIER MP3504W 35A 400V
CERAMIC CAP 100P 100V
CERAMIC CAP 10P 500V NPO
CERAMIC CAP 103 500V
CERAMIC CAP 22P/500V NPO
CERAMIC CAP 270P
CERAMIC CAP 33P/100V
CERAMIC CAP 68P/500V NPO
COIL 2.0x10x10.5t XPB-750
ELEC CAP 4700u80v
ELEC CAP 100u25v
ELEC CAP 220u16v
ELEC CAP 220u25v
ELEC CAP 1000u25v
SPACER XPM-900
CARTON XPB-1600
EXT .CART ON XPB-1600
SPACER 1200x570m/m
HOLDER XPB-1600
WALL XPB-1600
SLID PANEL XPB-1600
TOP COVER XPM-900
BOTTOM CABI XPB-1600
CARD BOARD 182x65x1t BLACK
M0VEABLE BUSHING KG-010
NYLON CLAMPER YJ-98
XPB-1600E BACK BOARD 230V
TUBE 22 m/m XPB-1600
TUBE 7 m/m XPB-1600
SPKON PC BOARD XPB1600E/750E
AL301/AL501 H-05XX-F 1.0m/mX3G
3P AC INLET R-301SN-M XPM-900
TO-92 HEAT SINK XPB-1600
TO-126 HEAT SINK XPB-1600
HEA T SINK 192x76x60 XPB-1600
TUBE 0.864 BLACK
SELF RETA TINING SP ALERS SS-6
TR 2SA1943-O
TR 2SC5200-O
TR 2SA1015GR T
TR 2SC1815GR T
XPB-1600 MAIN PC BOARD T=2oz
DIODE SF14
ZENER 3.3v 500mw
ZENER 8.2V 500mw
ZENER 15V 500mw
ZENER 15V 1W
DIODE 1N4004
DIODE 1N4148
MSC .1u 100V 5% T
MSC 1u 63V SC105J1J T
RESISTORS 3.3 ohm 1/4W T
RESISTORS 10 ohm 1/4W T
RESISTORS 100 ohm 1/4W T
RESISTORS 1 K 1/4W T
RESISTORS 10 K 1/4W T
RESISTORS 100 K 1/4W T
RESISTORS 1.3 K 1/4W T
RESISTORS 1.5 K 1/4W T
RESISTORS 160 ohm 1/4W T
RESISTORS 2 K 1/4W T
RESISTORS 22 K 1/4W T
RESISTORS 220 K 1/4W T
RESISTORS 24 K 1/4W T
RESISTORS 300 ohm 1/4W T
RESISTORS 30 K 1/4W T
RESISTORS 300 K 1/4W T
RESISTORS 330 ohm 1/4W T
RESISTORS 360 ohm 1/4W T
RESISTORS 510ohm 1/4W T
RESISTORS 8.2 K 1/4W T
RESISTORS 1.5 M 1/4W T
RESISTORS 1 ohm 1/2W T
RESISTORS 30 K 1/2W T
RESISTORS 1M 1% 1/4W T
RESISTORS 1.2K 1% 1/4W T
RESISTORS 1.3K 1% 1/4W T
RESISTORS 2.21K 1% 1/4W T
RESISTORS 121 ohm 1% 1/4W T
RESISTORS 150 ohm 1% 1/4W T
RESISTORS 162 ohm 1% 1/4W T
RESISTORS 10K 1% 1/4W T
RESISTORS 1 10K 1% 1/4W T
RESISTORS 24K3 1% 1/4W T
RESISTORS 40K2 1% 1/4W T
RESISTORS 68 K 1% 1/4W T
RESISTORS 23K2 1% 1/2W T
TR MPSA42
TR MPSA92
6.4m/m PIN (805551-BL2)
RECTIFER HEAT SINK XPB-1600
LED SPACER SUPPOR T LEDS-6.5
DIODE 1N5404
RECTIFIER KBP06 2A 600V
RECTIFIER MP3504W 35A 400V
CERAMIC CAP 100P 100V
CERAMIC CAP 10P 500V NPO
CERAMIC CAP 103 500V
CERAMIC CAP 22P/500V NPO
CERAMIC CAP 270P
CERAMIC CAP 33P/100V
CERAMIC CAP 68P/500V NPO
COIL 2.0x10x10.5t XPB-1600
ELEC CAP 6800u100v
ELEC CAP 100u25v
ELEC CAP 220u16v
ELEC CAP 220u25v
ELEC CAP 1000u25v
ELEC CAP 2200u25v
FUSE CLIP CQ-203SC
(10)
240
2
1
1
1
2
1
2
1
1
2
2
12
1
1
3
1
1
1
4
4
2
2
12
12
6
4
1
2
2
3
1
2
4
35
14
4
8
6
8
7
4
2
2
2
4
5
2
2
5
2
4
2
4
2
6
2
2
1
4
2
2
2
2
4
2
2
8
2
4
4
4
4
4
2
5
1
9
4
1
1
6
2
6
2
4
2
4
2
4
1
6
2
1
1
8
Page 11
Vendor Part #: Description: Quantity:
91) ECS02200025M
92) FC520CQ203SC
93) FS520ULC080F
94) ICNJM3404AD-
95) ICTL071CP—-
96) ICTL072CP—-
97) JS1001025003
98) JS1001025007
99) JS1001R25002
100) LDG050210030
101) LDR050410030
102) LDY050610030
103) MJ0860250900
104) MJCPJ-065—-
105) MPMEF104250K
106) NTM3x07x030Y
107) RC0200A20005
108) RC0206820005
109) RC0300A27005
110) RL832——12
111) RT0500122005
112) RT0500A02205
113) SR01MS3x081W
114) SR01TP4x204Y
115) SWL————1
116) SWS————1
117) TRMJE340—0
118) TRMJE350—0
119) TRMPSA13—0
120) TRTIP122—0
121) TRZ0103——0
122) W20105130055
123) W20105135205
124) W20105160051
125) W20105170208
126) W20105185205
127) W20105320202
128) W2070A2200BB
129) WS204x10x07W
130) PTH9M222—E2
131) PTH9M471—H1
132) SR01MS3x121B
133) SR03TP4x084B
134) WS132x08x10W
135) WS203x08x05W
136) 6000830380—
137) NTC0120L——
138) W2010G360051
139) W2010G440056
140) W20110120101
141) W20110120106
142) FH63032I——
143) FS630ULC060F
144) SPKONL4MDH01
145) SR01MS3x061B
146) SR01MS4x061W
147) SR01TP3x103B
148) SR03TP4x084B
149) W2010I12510A
150) W20110120101
151) WS408x04x10Y
152) LBC08——WH
153) 105142407902
154) KB1819BL0001
155) SR01TP3x063B
156) SWP————9
157) VR16A1031501
158) W5010A370032
159) W5010A460038
160) FAD012080001
161) FTSF-006——
162) IBXPB1600-GI
163) NTM8x17x080B
164) PB420215——
165) PT120———6
166) SR01MS3x081W
167) SR01MS3x121B
168) SR01MS4x082B
169) SR01TP35x84B
170) SR01TP3x063B
171) SR03TP4x084B
172) SR10MS8x751B
173) WDGEMINI——
174) WS407x03x09Y
175) LBC06——RD
ELEC CAP 2200u25v
FUSE CLIP CQ-203SC
FUSE 5x20 8A
IC NJM3404AD
ICTL071CP
IC TL072CP
BASE 3P 2.5m/m
BASE 7P 2.5m/m
BASE 2P JS-1001R-02
LED 5m/m GREEN
LED 5m/m RED
LED 5m/m YELLOW
CONNOC JACK 086-25-90
JACK CPJ-065 XPM-900
MEF .1u 250V 10%
NUT 3m/m W/S (0J0010-030001)
RESISTORS 2 ohm 2W M
RESISTORS 6.8 K 2W M
RESISTORS 2.7 ohm 3W M
832-1C-C-12D XPM-900
1.2 K 5W SQT TYPE
0.22 ohm 5W SOT TYPE
MS 3x8 (1JPHMC-030800)
TP4x20 (1JBH6C-042021)
SS004-P2430Em-PC10 XPM-900
SS004-P022 BY-PF8
MJE340
MJE350
TR MPSA13
TIP122
TRIAC Z0103 MA1A600V
1015#14 5/130/5 GREEN XPB-1600
1015#14 GREEN XPM-900
1015x14 5/160/5 BROWN XPB-1600
1015#14 5/170/20 GRAY XPB-1600
1015#14 GREEN XPM-900
1015#14 5/320/20 RED XPB-1600
1007#26 MIX XPB-1600
SPRING W/S.M4-L(2JS100-040050)
PTH9M04BE222TS2F333 XPM-900
PTH9M04BH471TS2F333 XPM-900
MS 3x12 BLACK
FMT+W TP 4x8 (1JBP6C-040825)
3.2x0.8x10 (2IFA032-081000)
SPRING W/S.M3-L(2JS100-030050)
XPB-1600 83x38 m/m P.BOARD 2oz
NTC 20A SCK-0120 XPM-900
1015#14 250R+360/5 BROWN
2015#14 250R+440/5 BLUE
1015#14 BROWN XPM-900E
1015#1410/120/10 BLUE XPB1600E
FUSE HOLD HTB-32I VDE TYPE
FUSE 6x30 FAST/GLASS U/C 6A
SPEAKER JACK XPM-900
MS 3x6 BLACK(1JBHMC-030604)
MS 4x6 (PLATING)
TP 3x10 BLACK (1JBHCC-031024)
FMT+W TP 4x8 (1JBP6C-040825)
1015#14 4.5+125/10 G&Y XPB1500
1015#14 BROWN XPM-900E
EXT TOOTH W/S. 4m/m
LABEL 8 m/m (GND)
FRONT PANEL XPB-750
KNOB 18x19 BLACK XPM-900
TP 3x6 BLACK (1JBHCC-030625)
R22-22B-11B XPM-900
16K4x1 10Ax1 41K L-15 XPM-900
2852#26 RED XPM-900
2852#26 GRAY XPM-900
SP802512H L=350m/m+XH
PLASTIC FOOT SF-006
MANUAL XPB-1600 (GEMINI)
NUT 5/16 (0A0220-310005)
PLOY BAG 8.5"x16.5"X0.05
TRANS.120m/m XPB-750E 230V
MS 3x8 (1JPHMC-030800)
MS 3x12 BLACK
MST 4x8 BLACK (1JBH1C-040824)
TP 3.5x8 (1JPH6C-3F0824)
TP 3x6 BLACK (1JBHCC-030625)
FMT+W TP 4x8 (1JBP6C-040825)
5/16x3" (1ATKMO-31C004)
GEMINI WARRANTY CARD
EXT TOOTH W/S. 3m/m
LABEL 6 m/m (VLOT)
12
12
10
20
14
Vendor Part #: Description: Quantity:
97) FS520ULC120F
1
98) ICNJM3404AD-
8
99) ICTL071CP—-
4
100) ICTL072CP—-
2
101) JS1001025003
2
102) JS1001025007
2
103) JS1001R25002
2
104) LDG050210030
2
105) LDR050410030
2
106) LDY050610030
5
107) MJ0860250900
2
108) MJCPJ-065—-
2
109) MPMEF104250K
2
110) NTM3x07x030Y
2
11 1) RC0200A20005
4
112) RC0206820005
113) RC0300A27005
1
114) RL832——12
4
115) RT0500222005
2
116) RT0500A03305
2
117) SR01MS3x081W
2
118) SR01TP4x204Y
2
119) SWL————1
8
120) SWS————1
1
121) TRMJE340—0
1
122) TRMJE350—0
1
123) TRMPSA13—0
1
124) TRTIP122—0
2
125) TRZ0103——0
2
126) W20105070052
2
127) W20105070058
1
128) W20105070059
129) W20105130055
2
130) W20105135205
1
131) W20105160051
1
132) W20105170208
2
133) W20105185205
1
134) W20105320202
1
135) W2070A2200BB
1
136) WS204x10x07W
2
137) 6001730470—
1
138) MPMEF104250K
2
139) RC0030A33005
2
140) RT0500A03305
141) PTH9M222—E2
8
142) PTH9M471—H1
8
143) SR01MS3x121B
144) SR03TP4x084B
145) WS132x08x10W
1
146) WS203x08x05W
2
147) 6000830380—
1
148) NTC0120L——
1
149) W2010G360051
1
150) W2010G440056
1
151) W20110120101
1
152) W20110120106
1
153) FH63032I——
3
154) FS630ULC100F
4
155) SPKONL4MDH01
1
156) SR01MS3x061B
157) SR01MS4x061W
8
158) SR01TP3x103B
1
159) SR03TP4x084B
1
160) W2010I12510A
161) W20110120101
1
162) WS408x04x10Y
1
163) LBC08——WH
1
164) 105142407901
2
165) KB1819BL0001
5
166) SR01TP3x063B
1
167) SWP————9
2
168) VR16A1031501
1
169) W5010A370032
1
170) W5010A460038
2
171) FAD012080001
4
172) FTSF-006——
1
173) IBXPB1500-GI
1
174) NTM8x17x080B
1
175) PB420215——
176) PT160——16
1
177) SR01MS3x081W
1
178) SR01MS3x121B
2
179) SR01MS4x082B
180) SR01TP35x84B
2
181) SR01TP3x063B
6
182) SR03TP4x084B
183) SR10MS8x751B
1
184) WDGEMINI——
1
185) WS407x03x09Y
1
186) LBC06——RD
4
FUSE 5x20 12A
IC NJM3404AD
ICTL071CP
IC TL072CP
BASE 3P 2.5m/m
BASE 7P 2.5m/m
BASE 2P JS-1001R-02
LED 5m/m GREEN
LED 5m/m RED
LED 5m/m YELLOW
CONNOC JACK 086-25-90
JACK CPJ-065 XPM-900
MEF .1u 250V 10%
NUT 3m/m W/S (0J0010-030001)
RESISTORS 2 ohm 2W M
RESISTORS 6.8 K 2W M
RESISTORS 2.7 ohm 3W M
832-1C-C-12D XPM-900
2.2 K 5W SQT TYPE
0.33 ohm 5W SQT TYPE
MS 3x8 (1JPHMC-030800)
TP4x20 (1JBH6C-042021)
SS004-P2430Em-PC10 XPM-900
SS004-P022 BY-PF8
MJE340
MJE350
TR MPSA13
TIP122
TRIAC Z0103 MA1A600V
1015#14 5/70/5 RED XPB-1600
1015#14 5/70/5 GRAY XPB-1600
1015#14 5/70/5 WHITE XPB-1600
1015#14 5/130/5 GREEN XPB-1600
1015#14 GREEN XPM-900
1015x14 5/160/5 BROWN XPB-1600
1015#14 5/170/20 GRAY XPB-1600
1015#14 GREEN XPM-900
1015#14 5/320/20 RED XPB-1600
1007#26 MIX XPB-1600
SPRING W/S.M4-L(2JS100-040050)
TR PC BOARD 171x42 m/m 2oz
MEF .1u 250V 10%
RESISTORS 3.3 ohm 1/4W T
0.33 ohm 5W SQT TYPE
PTH9M04BE222TS2F333 XPM-900
PTH9M04BH471TS2F333 XPM-900
MS 3x12 BLACK
FMT+W TP 4x8 (1JBP6C-040825)
3.2x0.8x10 (2IFA032-081000)
SPRING W/S.M3-L(2JS100-030050)
XPB-1500 83x38 m/m P.BOARD 2oz
NTC 20A SCK-0120 XPM-900
1015#14 250R+360/5 BROWN
2015#14 250R+440/5 BLUE
1015#14 BROWN XPM-900E
1015#1410/120/10 BLUE XPB1600E
FUSE HOLD HTB-32I VDE TYPE
FUSE 6x30 FAST/GLASS U/C 10A
SPEAKER JACK XPM-900
MS 3x6 BLACK(1JBHMC-030604)
MS 4x6 (PLATING)
TP 3x10 BLACK (1JBHCC-031024)
FMT+W TP 4x8 (1JBP6C-040825)
1015#14 4.5+125/10 G&Y XPB1500
1015#14 BROWN XPM-900E
EXT TOOTH W/S. 4m/m
LABEL 8 m/m (GND)
FRONT PANEL XPB-1600
KNOB 18x19 BLACK XPM-900
TP 3x6 BLACK (1JBHCC-030625)
R22-22B-11B XPM-900
16K4x1 10Ax1 41K L-15 XPM-900
2852#26 RED XPM-900
2852#26 GRAY XPM-900
SP802512H L=350m/m+XH
PLASTIC FOOT SF-006
MANUAL XPB-1600 (GEMINI)
NUT 5/16 (0A0220-310005)
PLOY BAG 8.5"x16.5"X0.05
TRANS. 160m/m XPB-1600E 230V
MS 3x8 (1JPHMC-030800)
MS 3x12 BLACK
MST 4x8 BLACK (1JBH1C-040824)
TP 3.5x8 (1JPH6C-3F0824)
TP 3x6 BLACK (1JBHCC-030625)
FMT+W TP 4x8 (1JBP6C-040825)
5/16x3" (1ATKMO-31C004)
GEMINI WARRANTY CARD
EXT TOOTH W/S. 3m/m
LABEL 6 m/m (VLOT)