Gemini GEM-P400 User Manual
Using Your GEM-P400 Security System
GEMINI
1 2 3 4
STATUS
ARMED
Oi230a
page 1
&20387(5,=(' 6(&85,7< 6<67(0
Tuesday, September 16, 1997 08:26
Tuesday, September 16, 1997 08:26
Oi230a
page 2
Introduction
Congratulations
manufacturer of state-of-the-art secur ity products, this system will provide you with unprecedented peace-of-mind & incorporates some of the most sophisticated features available today. Above all, it has been designed an extra step, to provide all those
operating it with very easy, intuitive use. Please carefully review the information contained in this manual, so that you and all
potential users of the system familiar ize yourselves with its operation, and can therefore take full advantage of GEMINI’s many
convenience features and amenities.
Your system
Decorator Keypads for controlling the system, and various security detection devices. These detection devices are divided
among separate areas known as “zones”, set up throughout your premises. Each zone number corresponds to a Zone light on
your Keypad’s display area.
When a zone’s num ber is ON (or lit), it indic ates that one or more detection device(s) as s igned to that area are active or open.
For example, if Zone 1 is the front door, and it is open, the 1 on the keypad display will be lit. If zone 2 is a motion detector, and
there is movement in that area, 2 will light. Depending upon the actual layout your security professional has chosen to properly
protect your premises, each zone may function a little differently: The zone protecting your front door may be programmed
as an Exit/Entry zone to allow you time to enter the premises and disarm the system , without inadvertently sounding the alarm.
Alternatively, a zone protecting a window could be designated as an “instant” zone, so that if it is entered or opened while the
system is on/armed, there will be an immediate alarm.
Your easy
entering your four digit User Code. This includes Arm ing (or ac tivating) and Disarm ing (or deactivating) the s ystem. Simply put,
ARMED means the system is ON; DISARMED means the system is OFF. If the system is O FF and you want to turn it ON, just
enter your Code. To turn the system back OFF, enter your code again.
alarm, entering your User Code will silence all Sirens.
informed visibly, using its zone and status lights and audibly, using its built-in keypad sounder. For more inf ormation, please see
Keypad Controls and Indicators on page 5.
GEMINI Keypad
on your purchase of an advanced GEMINI-P400 Security System. Meticulously developed by a leading
consists of a contr ol panel (a computer housed within a white metal panel enclos ure), one or m ore GEMINI
puts super-simple system control at your fingertips.
Most keypad commands involve
It’s easy, just always remember, in the event of an
Your keypad is your command and status center, it keeps you
3
Oi230a
page 3
Tuesday, September 16, 1997 08:26
Introduction
Table of Contents
Keypad Controls and Indicators ................................... 5
Arming your System (When Leaving) ........................... 6
Protecting Yourself While Home .................................. 7
Emergency Keys .......................................................... 8
Disarming the System .................................................. 9
Silencing an Alarm....................................................... 9
Special Functions ........................................................ 10
System Troubles .......................................................... 11
Programming User Codes ............................................ 13
Glossary ....................................................................... 14
Important - Test Your System Weekly !
1
Bell / Battery Test
Test your bell or siren by pressing
This will cause the bell or siren to sound for 2 seconds
andalso initiate a test of the battery .
2
Zone Test
Walk throughout the premises opening each protected
door or window, and activating each motion sensor.
Check the keypad to see that each respective zone
number displays in the window.
4
followed by
System Information
Central Station Phone Number: ____________________
Central Station Account Number: ____________________
For Service Call: ____________________
Entry Delay: ____________________
Exit Delay: ____________________
Alarm Time-out: ____________________
3
Central Station Communication Test
(This test should only be performed on weekends or at a
time designated by your alarm company)
1.Notify Central Station of the impending test.
.
2. Secure all zones to light Status Light on your keypad.
3. Enter your User Code followed by
4. Violate your alarm by opening a window / door etc.
5. The siren or bell should sound and the system will send
the alarm signals to the Central Station
6.Enter your User Code followed by
7. Call Central Station to insure that the alarm signals were
received properly.
to Arm the system.
to silence the alarm.
Oi230a
page 4
Tuesday, September 16, 1997 08:26
Keypad Controls and Indicators
g
g
Trouble Light
will light and the Keypad
sounder will pulse to indicate that a system trouble is present. (See System troubles, Page 11)
Status Light will light when all zones are secure
and system is ready to be Armed.
Armed Light will light when system is Armed,
and will flash when system is in Alarm
Press
followed by the corresponding
Function number to enable special functions and
options. (See Special Functions, Page 10)
To Bypass a zone, press
and the zone
number to be bypassed, and then Arm system.
Press
to reset Fire Zone, clear miss-
entered codes, reset Alarm Memory, etc.
Zone Lights (
that the correspondin
1 throu
h 4) will light to indicate
Zone is open, and will
flash to indicate a zone in alarm.
GEMINI
1 2 3 4
STATUS
ARMED
&20387(5,=(' 6(&85,7< 6<67(0
Numerical
Keys 1-9, 0.
Used to enter User
Codes, Zone
numbers,
etc.
Emergency
to signal an emergency condition.
Press:
+
+
(Programmable)
Keys Press simultaneously
for Auxiliary Emergency or
for Police Emergency.
Press
to bypass all
interior protective devices such
as motion
sensors, etc.
Press
after entering
User Code
when Arming
or Disarming
System.
Press
to remove
entry delay
from the Exit/
Entry door.
5
Oi230a
page 5
Tuesday, September 16, 1997 08:26
Loading...