AC 2729/UK Rev. 00 - 06/10
UK
839
INSTALLATION AND
USE MANUAL
Made in Italy
Reg. n.532-A
UNI EN ISO 9001:2008
1.0
2.0
3.0
4.0
5.0
8.0
9.0
10.0
11.0
12.0
- PRELIMINARY ADVICE.............................................................................................
- OPERATING DESCRIPTION.....................................................................................
2.1 - Vehicle CDL locking.................................................................................................
2.2 - Vehicle CDL locking and comfort control.................................................................
2.3 - Vehicle CDL unlocking..............................................................................................
- REMOTE CONTROL BATTERIES REPLACEMENT..................................................
- CONNECTOR TABLE................................................................................................
- COMPLETE ELECTRIC DIAGRAM...........................................................................
...........................................................
...............................................................
- ...................................
System self-rearming and door locking....................................................................
Central door locking setting time..............................................................................
8.3 - Window comfort closure...........................................................................................
8.4 - Double impulse in opening.......................................................................................
8.5 - Doors push-buttons polarity selection......................................................................
- ................................................
- WARRANTY CONDITIONS......................................................................................
- WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEE) DIRECTIVE........
- TECHNICAL SPECIFICATIONS...............................................................................
USER MANUAL
INSTALLER MANUAL
6.0
7.0
- ADD NEW DEVICES.......................................
- DELETION OF PROGRAMMED DEVICES
PROGRAMMABE FUNCTIONS DESCRIPTION....................
8.1 -
8.2 -
SYSTEM PROGRAMMING........................................
PAGE 02
1.0 - PRELIMINARY ADVICE
Dear Customer,
:
the following warning signs in the present manual provide important notices to the installer and the
user for installing and using this product correctly
PAGE 02
PAGE 03
PAGE 03
PAGE 03
PAGE 03
PAGE 03
PAGE 04
PAGE 05
PAGE 06
PAGE 07
PAGE 08
PAGE 08
PAGE 08
PAGE 08
PAGE 08
PAGE 08
PAGE 08
PAGE 09
PAGE 09
PAGE 09
Indications useful for theuser.
This icon provides the user with indications for a diversificated use of the system or it
simply provides indications useful for the use.
Indications useful for the installer.
This icon indicates to the installer a diversificated operating, according to the connection
and the programming of the system or it simply provides indications useful for the
installation.
!
TABLE OF CONTENTS
UK
USEER MANUAL - PAGE 03
2.0 - OPERATING DESCRIPTION
USER MANUAL
2.1 - VEHICLE CDL LOCKING
2.2 - VEHICLE CDL LOCKING AND COMFORT CONTROL
2.3 - VEHICLE CDL UNLOCKING
Press the button on the remote control;
.
.
Press the button on the remote control;
..
To prevent problems with the remote control, it has been provided with a device that will signal the
charge condition of the batteries inside.
During normal use of the remote control, when you press a command button the green LED will light
up with a steady light.
If the batteri
.
For battery replacement follow the indications reported below
the LED will light up steady for 10” and the turn indicators will
blink twice to confirm that the vehicle has been locked .
After this lapse of time, the LED will start blinking until the system is disarmed
If the comfort feature is activated, the vehicle doors will lock and the windows will roll up.
In this case the LED will light up steady during the comfort locking and stay lit for 10” afterwards.
If the remote has two buttons, the comfort feature can be excluded by pressing first the dotted button
(lock) and then the smooth button (comfort exclusion)
the turn indicators will blink three times to confirm that the
vehicle has been unlocked
es are too weak for normal operation of the remote control, when the button is pressed the
green LED will start blinking, advising you that it is time to replace the batteries
3.0 - REMOTE CONTROL BATTERIES REPLACEMENT
.
This manual also refers to the LED and to its various optical signals.
The LED is optional and therefore not included in the kit.
Separate the
plastic shells of
the remote
control, paying
attention to not
damage the
internal circuit.
Remove the discharged
batteries and insert the new
batteries in their housing, taking
care not to invert the polarity.
Close the
plastic shells
of the remote
and verify the
remote control
works
properly.
BATTERIES
Use only batteries of Cr1616 type.
Discard used batteries properly in special dedicated containers.
PAGE 04 - USER MANUAL
4.0 - CONNECTOR TABLE
-------
Doors push-button input
Positive under key
-------
-------
Power supply ground
-------
Positive output with system armed (+A)
LED negative output
LED positive output
Power suppply positive
Antenna
-------
-------
-------
Turn signals positive/negative output
Turn signals positive/negative output
Turn signals positive/negative common
CDL
CDL
CDL
CDL
CDL
CDL
-1-
-2-
-3-
-4-
-5-
-6-
-7-
-8-
-9-
-10-
-11-
-12-
-13-
-14-
-15-
-16-
-17-
-18-
-19-
-20-
-21-
-22-
-23-
-24-
-------
GREEN-BROWN
YELLOW
-------
-------
BROWN
-------
PINK
BLACK
RED
RED
BLACK
-------
-------
-------
ORANGE
ORANGE
WHITE-RED
RED-GREY
RED-BROWN
RED-BLUE
YELLOW-BLUE
YELLOW-BROWN
YELLOW-GREY
WIRE FUNCTIONPOSITION
WIRE COLOUR
INSTALLER MANUAL
The positive under key (YELLOW wire) and the door signal (GREEN-BROWN wire)
MUST BE CONNECTED for some operating modes and configurations.
Therefore these connections must ALWAYS be done.
!
INSTALLER MANUAL - PAGE 05
15A
+
Battery
10A
BROWN
GROUND
POSITIVE
RED
It is reccomended to use a 10A fuse
WHITE-RED
ORANGE
ORANGE
Turn signals relay common
Turn signals output
YELLOW
+30
Positive under key
Antenna, do not tamper
Doors push-button input
Positive output with
system armed (+A)
BLACK
GREEN-BROWN
PINK
5.0 - COMPLETE ELECTRIC DIAGRAM
YELLOW-BROWN
RED-BROWN
YELLOW-GREY
RED-GREY
See CDL diagrams
YELLOW-BLUE
RED-BLUE
Before carrying out all
electrical connections,
disconnect the negative
battery terminal and re-
connect again after
completion.
!
Red
KIT2322NF
KIT2323S
Black
PAGE 06 - INSTALLER MANUAL
6.0 - ADD NEW DEVICES
In order to carry out successfully the operation, it is necessary to make the required
electrical connections (door switch and positive under key).
!
The system can 50 remote controls.
For procedure activation follow the indications reported below.
With the system being disarmed, open and keep opened vehicle driver side door.!
learn up to
!
!
!
Turn the vehicle ignition key in “ON”-“OFF”-“ON”-“OFF”-“ON”-“OFF”-“ON” position.
After the fourth commutation, let the vehicle ignition key to “ON”.
The system will indicate the remote control learning procedure starting by two flashes of the LED
and the turn indicators.
!
!
!
!
!
The system is now waiting to receive the new device code.
Press the button on th remote control; the system will indicate the new device learning by a flash of
the LED
Repeat the procedure to save to memory other devices.
Turn the vehicle ignition key to “OFF” position and close the door.
The procedure completion will be indicated by one long flash of the LED and one of the turn
indicators.
The following operations must be carried out within four seconds, otherwise the
procedure will be invalidated.
Do not modify the door position otherwise previously saved to memory devices will be
deleted, like described in the next paragraph.
Storing memory is for 50 devices. When an extra one is added, it will automatically
delete the first device registered.
!
!
!
INSTALLER MANUAL - PAGE 07
7.0 - DELETION OF PROGRAMMED DEVICES
In order to carry out successfully the operation, it is necessary to make the required
electrical connections (door switch and positive under key).
!
The system includes a devices deletion procedure.
PFor procedure activation follow the indications reported below.
With the system being disarmed, open and keep opened vehicle driver side door.!
!
!
!
!
!
Turn the vehicle ignition key in “ON”-“OFF”-“ON”-“OFF”-“ON”-“OFF”-“ON” position.
After the fourth commutation, let the vehicle ignition key to “ON”.
The system will indicate the devices deletion procedure starting by two flashes of the LED and the
turn indicators.
Close the door; the LED will be illuminated constantly.
Keep the door close till the moment, after about eight seconds, the complete deletion of devices will
take place.
!
!
The procedure completion will be indicated by LED’s turning off.
Turn the vehicle ignition key to “OFF” position.
The following operations must be carried out within four seconds, otherwise the
procedure will be invalidated.
If the door is opened before 8 seconds, devices will not be deleted.
!
!
PAGE 08 - INSTALLER MANUAL
8.0 -
“SYSTEM PROGRAMMING”.
This function allows vehicle's protection in case the user disarms accidentally the system.
Thus, the system will be automatically rearmed after 30”, if no intervention on the vehicle is done (i.e.
door opening, engine start).
.
Function that allows to select the CDL closure time.
This function allows activating the comfort control (window closing) when the system is armed.
This function activates twice the opening control and it is used on vehicles with diversified opening.
This function modifies the alarm input signal (positive or negative) according to the signal deriving
from the door’s button.
8.1 - SYSTEM SELF-REARMING AND DOOR LOCKING
8.2 - CENTRAL DOOR LOCKING SETTING TIME
8.3 - COMFORT CLOSURE CONTROL
8.4 - DOUBLE IMPULSE IN OPENING
8.5 - DOORS PUSH-BUTTONS POLARITY SELECTION
PROGRAMMABLE FUNCTIONS DESCRIPTION
This chapter covers the various features of the system which can be programmed as described in
Together with the system self-rearming, the automatic door locking of the vehicle is done when
running.
Being closed all the doors of the vehicle, turn the ignition key to “ON”; after 20”, all doors will be locked.
By turning the ignition key to “OFF”, all doors of the vehicle will be automatically unlocked
9.0 - SYSTEM PROGRAMMING
FUCTION STATUS BUTTON VEHICLE KEY
System self-rearming
Setting of opening/closing time (1” or 6”)
25” comfort closure
Doors lock double impulse in opening
Selection of doors input polarity
The system has a “standard configuration” programmed during manufacturing procedure by Gemini.
:
With the system disarmed and doors closed, turn the vehicle ignition key to “ON” position.
The status LED stay on for one second; during this time, push the button on the remote control.
Starting of programming procedure is indicated by three flashed of the LED and the turn indicators
and furthermore the LED is permanently illuminated.
To able and disable the functions, follow the below table, take into consideration that every
.
!
!
!
!
For programming modification proceed as follows
press of
the push button or rotation of the ignition key will cycle to the next feature. The LED will turn off
briefly after each press of the remote and turn off twice after each key rotation
Do not modify the functions which have been programmed during the installation
ntering the programming procedure resets the functions to the default Setting
.
E .
!
!
Once the last function has been programmed, the system indicates the end of programming
procedure by three flashed of LED and turn indicators.
Turn the vehicle ignition key to “OFF” position.
Enable
Enable 6”
AAttiva
ttiva
Enable positive
polarity
Disable
Enable 1”
DDisable
isable
Enable positive
polarity
Disabled
Disabled
Disabled
Enabled
negative
Selected 1”
!
INSTALLER MANUAL - PAGE 9
12.0 - TECHNICAL SPECIFICATIONS
Power supply 839
Current absorption @ 12Vdc with system armed and LED flashing
Working temperature range
Turn signals relay contact capacity
Maximum positive current output when armed (+A)
12/24 Vdc
15 mA
From -30°C to +70°C
8 A at 20°C
700 mA
APPROPRIATE
CONTAINER
ONLY
!
11.0 - WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT
(WEEE) DIRECTIVE
In the European Union, this lable indicates that this product must not be disposed of with household
waste. It should be deposited at an appropriate facility to enable recovery and recycling (directive
2002/95/CE, 2002/96/CE and 2003/108/CE).
For information on how to recycle this product responsibly in your Country, please visit the web-site:
Www.eur-lex.europa.eu
10.0 - WARRANTY CONDITIONS
This 24 months from the installation date
shown on this warranty coupon, taking into consideration the 1999/44/CE.
Therefore, you are kindly requested to fill entirely the guarantee certificate included in this booklet and
to NOT REMOVE the guarantee label from the device.
product is guaranteed to be free from manufacturing defects
The warranty will become void if labels are missing or torn, if the installation certificate is not fully
compiled or if the enclosed sale document is missing.
The guarantee is valid exclusively at authorized Gemini Technologies S.p.A. Service Centers.
The manufacturer declines any responsibility for eventual malfunctions of the device or any damage
to the vehicle electrical system due to improper installation, use or tampering.
Declaration of conformity to type
Dichiarazione di conformità
I hereby declare that the product
(Name of product, type or model, batch or serial number)
Is conform to all relevant essential requirements of the R&TTE-directive 1999/5/EC, issued March
9,1999. According to Annex IV of the R&TTE directive. The following standards and essential radio
test suites published in the “Official Journal” of the European Communities, have been used to
demonstrate the conformity of the product:
Qui di seguito si dichiara che il prodotto
(nome del prodotto o modello, categoria o numero di serie)
7208E - 7218E
Product in class 1 frequency identification - subclass 20
Electrical safety:
Radio and spectrum parameters:
Electromagnetic compatibility EMC:
Prodotto in frequenza identificata come classe 1 - sottoclasse 20
Sicurezza elettrica:
Radio e parametri di trasmissione:
Compatibilità elettromagnetica EMC:
The product can be used in the following European Countries:
Il prodotto può essere immesso nei seguenti Stati Europei:
Company responsible for placing on the market:
Società responsabile per l’immissione nel mercato:
Address:
Indirizzo:
Point of contact:
Persona di contatto:
Bodio Lomnago - 19/09/2003
(Signature) - (Firma)
Via Luigi Galvani 12 - 21020 BODIO LOMNAGO (VA) -
ITALY
Andrea Rossi
A, B, D, DK, F, FR, GR, IR, I, L, NL, P,
SP,S,UK
GEMINI TECHNOLOGIES S.p.A.
EN 60950-1 (2001) + A11 (2004)
EN 300220-2 V2.1.1 EN 50371 (2002)
EN 301489-3 V1.4.1 EN 301489-1 V1.6.1
EN 60950-1 (2001) + A11 (2004)
EN 300220-2 V2.1.1 EN 50371 (2002)
EN 301489-3 V1.4.1 EN 301489-1 V1.6.1
Soddisfa tutti i requisiti applicabili alla tipologia del prodotto e richiesti dalla regolamentazione delle
telecomunicazioni secondo direttiva R&TTE 1999/5/CE allegato IV tramite l’utilizzo delle norme
pubblicate nella gazzetta ufficiale della Comunità Europea:
7 Dudley Court , Jessop Close, Clacton-on-Sea, Essex, CO15 4LY
TEL: +44 (0) 1255 434353
Email: sales@avsgemini.com | Web: www.avsgemini.com
UK Distributors of the Gemini Alarm Systems
Loading...