Gembird SIS-PMS-LAN User Manual

РУКОВОДСТВО ПОЛЬЗОВАТЕЛЯ

КЕРІВНИЦТВО КОРИСТУВАЧА

USER MANUAL

HANDBUCH

HANDLEIDING

MANUEL DESCRIPTIF

SIS-PMS-LAN PROGRAMMABLE

SURGE

PROTECTOR WITH LAN INTERFACE

Silver Shield programmable surge protector

with LAN interface

Silver Shield programmierbare und

fernbedienbare Steckdosenleiste mit LAN-

Anschluss

Silver Shield programmeerbare stekkerdoos

met LAN interface

Silver Shield Boîtier commandé à distance et

programmable avec prise LAN

Программируемый сетевой фильтр с LAN-

интерфейсом

Програмований мережевий фільтр з LAN-

інтерфейсом

2

All brands and logos are registered trademarks of their respective owners

SIS-PMS-LAN PROGRAMMABLE

SURGE

PROTECTOR WITH LAN INTERFACE

1. Introduction

Congratulations with your purchase of this Silver shield Power

Manager. Your SIS-PMS-LAN is an advanced surge protector with power

management features. Four sockets are individually manageable via the
LAN interface.

The sockets can be switched on/off by a timer schedule, by user or
different events. It is also possible to pre-program the unit event timer
schedule (hardware schedule) and then disconnect SIS-PMS-LAN from
LAN and use it elsewhere. The device can be used as an advanced
standby-killer.

1.1. Features

• The main rocker switch enables switching all the sockets on and off

• In addition to it every manageable socket can be switched on and off

via the software control window or web browser

• The unit can be pre-programmed via hardware-based schedule. The

hardware schedule will work even when the managing computer is

switched off

• The unit will keep performing the programmed hardware time

schedule even after SIS-PMS-LAN is disconnected from the power

for some time

3

All brands and logos are registered trademarks of their respective owners

SIS-PMS-LAN PROGRAMMABLE

SURGE

PROTECTOR WITH LAN INTERFACE

• The manageable sockets can then be switched on and off by the

schedule, simple typical applications could be: “switch my

peripherals on every working day at 8:50 AM” etc

• The manageable sockets can also be programmed with Power

Manager software to react whenever a certain event occurs

(Windows or other programs start-up/shutdown), simple typical

applications could be: “switch my scanner on when I want to scan”

or “switch my printer off whenever I exit Windows”

• LAN interface: the unit can be assigned an IP address and/or a

network name as a shared LAN resource and can be afterwards

accessed and managed from anywhere within the local area network

or Internet

• Built-in web-server: SIS-PMS-LAN can be managed from any

computer running Internet Explorer or any other web browser –

therefore a global access is possible

• IP-filter and 64-bit password protected encryption of data guarantee

secure access to SIS-PMS-LAN

• Real time Voltage monitor provides information about the actual

status of each manageable socket (on or off). This information can

be further utilized in various ways (e.g. to check the proper

execution of the switching commands)

4

All brands and logos are registered trademarks of their respective owners

SIS-PMS-LAN PROGRAMMABLE

SURGE

PROTECTOR WITH LAN INTERFACE

1.2. Specifications

• Input voltage: 220 – 230 VAC, 50 – 60 Hz

• Maximum load: 10 A

• Maximum power consumed by SIS-PMS-LAN: 2.5 W

• Built in power supply and battery

• Hardware schedule features:

• Maximum number of independent hardware schedule events –

16 per socket

• Time interval between the events – from 1 minute to 180 days

• Timer accuracy: no more than 2 seconds error per day providing

power is always present. Otherwise there can be an additional
(up to 2 seconds) error per each power off. There is no
accumulation of errors at all if NTP correction option is set (see
section 5.4 below)

• Working temperature range: from +10 to +40 °C

• Dimensions: 378 x 98 x 55 mm

• Net weight: 1.0 kg

5

All brands and logos are registered trademarks of their respective owners

SIS-PMS-LAN PROGRAMMABLE

SURGE

PROTECTOR WITH LAN INTERFACE

1.3. Hardware requirements

• Local area network with RJ45 sockets

• Any Internet-enabled computer connected to the local area network

• Computer running Windows® 2000/XP/Vista or Windows 7 is

required for using the Power Manager software (use of this software

is not compulsory)

1.4. Package contents

• SIS-PMS-LAN

• User manual and Quick installation guide

• RJ45 cross-over cable (red), RJ45 LAN cable (grey)

• CD with Power Manager software for Windows

6

All brands and logos are registered trademarks of their respective owners

SIS-PMS-LAN PROGRAMMABLE

SURGE

PROTECTOR WITH LAN INTERFACE

2. Indicators and controls of the SIS-PМS-LAN

Non manageable

Manageable socket 4

Manageable socket 3

Manageable socket 2

Manageable socket 1

Non manageable

socket

Side panel #1

Figure #1

socket

Indicator
Socket 1

Side panel #2

Main rocker

switch (Z)

Power indicator

Indicator
Socket 4

Indicator
Socket 3

Indicator
Socket 2

All brands and logos are registered trademarks of their respective owners

7

SURGE

2.1. Side panel #1

Reset

Button (A)

Master Switch

Button (B)

IP Config

Button (C)

SIS-PMS-LAN PROGRAMMABLE

PROTECTOR WITH LAN INTERFACE

Figure #2

Indicator

Schedule/LAN activity

LAN socket

8

All brands and logos are registered trademarks of their respective owners

SURGE

2.2. Side panel #2

SIS-PMS-LAN PROGRAMMABLE

PROTECTOR WITH LAN INTERFACE

Figure #3

Circuit breaker

Power cord

9

All brands and logos are registered trademarks of their respective owners

SIS-PMS-LAN PROGRAMMABLE

SURGE

PROTECTOR WITH LAN INTERFACE

2.3. Indicators

• Main rocker switch Z (see Figure #1 above) is lit – this means that

SIS-PMS-LAN is connected to the power supply and active

• Power indicator (see Figure #1 above) is lit – this means that the

non-manageable sockets (marked with the sign ) are

switched on

• The indicator Socket 1 (2,3,4) (see Figure #1 above) is lit – this

means that this particular socket is switched on

• The indicator Schedule/LAN activity (see Figure #2 above) blinks

green – this means that there is some LAN activity taking place

• The indicator Schedule/LAN activity (see Figure #2 above) blinks

red as the reset procedure is being executed

• The indicator Schedule/LAN activity (see Figure #2 above) stays

red if an active hardware schedule for any socket exists

10

All brands and logos are registered trademarks of their respective owners

SIS-PMS-LAN PROGRAMMABLE

SURGE

PROTECTOR WITH LAN INTERFACE

3. Installation

• It is strongly recommended to avoid damp or wet places for

installation.

• SIS-PMS-LAN should be connected to the European AC wall socket

of the standard DIN 49 440.

3.1. Getting started

• Connect SIS-PMS-LAN to the wall socket first and then to the LAN

socket (or your computer LAN card) with the provided patch cord or

vice-versa.

• SIS-PMS-LAN can now be switched on and off by means of the

Main rocker switch (Z).

• Two (the first and the last) sockets of SIS-PMS-LAN are marked with

the symbol . These two sockets are switched on and off by

means of the Main rocker switch (Z) and cannot be managed by the

computer – so they are called non-manageable sockets in this

manual.

• If SIS-PMS-LAN is switched on then the red indicator POWER is lit.

In this case both non-manageable sockets are now live and

connected to the power supply.

11

All brands and logos are registered trademarks of their respective owners

SIS-PMS-LAN PROGRAMMABLE

SURGE

PROTECTOR WITH LAN INTERFACE

• The sockets: Socket 1, Socket 2, Socket 3 and Socket 4 can be

managed or pre-programmed by computer via LAN. They are called

manageable sockets in this manual.

• The manageable sockets of SIS-PMS-LAN can be programmed to

be on or off. The current status of each manageable socket is

represented by the corresponding indicator which will be lit if socket

has power to it.

• If the Main rocker switch (Z) (see figure #1 above) is turned off then

the manageable sockets cannot be switched on by either web server,

Power manager software or the hardware schedule.

• As soon as you turn the Main rocker switch (Z) on then the web

server, Power manager software or the hardware schedule will be

able to turn the manageable sockets on and off.

• Master switch button (B) (see figure #2 above) can also switch all

the manageable sockets on and off regardless of their current status

or schedule that is being executed. To switch them on you should

keep the button pressed for 1-2 seconds. To switch them off you

should keep the button pressed for more than 3 seconds.

• To protect the connected devices from possible high current and

short circuit SIS-PMS-LAN is equipped with the automatic circuit

breaker.

• NOTE: If the total power consumption (or peak power) of the

devices, connected to SIS-PMS-LAN exceeds 2200 Watts, the

circuit breaker may power SIS-PMS-LAN off. In this case, please,

12

All brands and logos are registered trademarks of their respective owners

SIS-PMS-LAN PROGRAMMABLE

SURGE

PROTECTOR WITH LAN INTERFACE

remove the excessive load first and then press the Circuit breaker

button to restore the power supply (see figure #3 above).

To be able to use SIS-PMS-LAN you will now have to complete its
LAN configuration.

3.2. Preparing LAN configuration of SIS-PMS-LAN

Before configuring SIS-PMS-LAN hardware settings, please, let it
obtain its IP address. Follow the steps below:

• Make sure SIS-PMS-LAN is connected to the local network with the

provided RJ-45 cable (option A - recommended)

NOTE: you may prefer to connect SIS-PMS-LAN directly to the
managing computer LAN adapter (network card) using the supplied
crossover RJ-45 cable (option B)

• Turn SIS-PMS-LAN off (with the Main rocker switch Z)

• Press IP Config (C) button on the side control panel (see figure #2

above) with the tip of a pen

• While holding it pressed, turn the Main rocker switch Z on and wait

for about 3 seconds until you hear the sockets switching twice

The above-mentioned procedure forces SIS-PMS-LAN to reset itself
to the default settings (see below) ...

13

All brands and logos are registered trademarks of their respective owners

SIS-PMS-LAN PROGRAMMABLE

SURGE

PROTECTOR WITH LAN INTERFACE

• IP: 192.168.0.254

• Subnet mask: 255.255.255.0

• Gateway: 192.168.0.1

• DNS:0.0.0.0

• DHCP: enabled

• IP filtering: disabled

• Power Manager client port: 5000

.. and then search for an IP address from your eventual DHCP
server If no DHCP server is found within 30 seconds, SIS-PMS-LAN will
then automatically revert to the default settings (see above, with IP:

192.168.0.254) and additionally disable DHCP option.

3.3. Power Manager installation

It is now time to identify which IP address has been obtained by SIS­PMS-LAN. We need to carry out the following:

• Insert the Power Manager CD into a PC CD-ROM drive. This PC

can be connected either to the same LAN where the device is (if you

chose option A section 3.2) or directly to the device with the

crossover RJ-45 cable (if you chose option B section 3.2)

• If for any reason the automatic setup does not work, then open CD-

ROM drive in the My Computer window and launch SETUP.EXE

from the CD

• Follow instructions of the installation software

14

All brands and logos are registered trademarks of their respective owners

SIS-PMS-LAN PROGRAMMABLE

SURGE

PROTECTOR WITH LAN INTERFACE

NOTE: Antivirus or firewall software may block connection to SIS-

PMS-LAN. Please, configure antivirus/firewall to permit connection to
the IP address and port of your SIS-PMS-LAN

3.4. IP configuration

The utility Find SIS-PMS-LAN (see Figure #4 below) will run
automatically during the software installation but it can also be started
from Start/All Programs/Gembird/Power Manager. The IP range where
you would like to search for SIS-PMS-LAN will be set automatically
according to the IP settings of your LAN adapter but can be changed
manually in the Adapter subnet fields. Now press the Search button.

NOTE: only SIS-PMS-LAN within a local subnet can be found. If
your computer LAN adapter is not in the (default) subnet of SIS-PMS­LAN (as might probably be the case if you chose option B section 3.2)
you will have to change its IP address manually to be able to find SIS­PMS-LAN. For example if you wish to find SIS-PMS-LAN (with the default
IP 192.168.0.254), the IP address of your computer should be set as

192.168.0.XXX (where XXX stands for any digit, for example 1) and the
subnet mask should be 255.255.255.0.

After the searching the IP addresses of the found SIS-PMS-LAN
devices will appear in the list box. Select SIS-PMS-LAN which you want
to access, and press the Open button (see Figure #4 below).

15

All brands and logos are registered trademarks of their respective owners

SIS-PMS-LAN PROGRAMMABLE

SURGE

PROTECTOR WITH LAN INTERFACE

Figure #4

The window of your default internet browser will be then opened to
give you access to the built-in web-server. See section 4 below for the
further details.

16

All brands and logos are registered trademarks of their respective owners

SIS-PMS-LAN PROGRAMMABLE

SURGE

PROTECTOR WITH LAN INTERFACE

4. The web server

Your SIS-PMS-LAN is equipped with a web-server which allows
managing the device using any web browser such as Internet Explorer
etc.

4.1. Web-server login page

To access the web server of SIS-PMS-LAN, just open Internet
Explorer (or other browser) and input the IP address of SIS-PMS-LAN
(for example http://192.168.1.241). If you have used Find SIS-PMS-LAN
utility to locate SIS-PMS-LAN then you will be taken to this webpage
automatically. Login page will then be displayed (see Figure #5 below).

NOTE: Java script must be enabled in your Internet Explorer (or
another browser) settings. Otherwise, you get an error message:
WARNING! JAVASCRIPT IS DISABLED!

Figure #5

The default password is 1. It is recommended to change the
password on the Device settings page (see section 4.4 below) after the
first login.

17

All brands and logos are registered trademarks of their respective owners

SIS-PMS-LAN PROGRAMMABLE

SURGE

PROTECTOR WITH LAN INTERFACE

After a successful login you will face the Socket 1 Status page (see
section 4.2 below).

NOTE: There is a possibility that you might then need to open the
LAN settings page (see section 4.3 below) to complete the IP
configuration.

4.2. Socket page

There are 4 manageable sockets on SIS-PMS-LAN and so there are
4 pages corresponding to them. On each status page you can see the
status of the socket (on or off) and you have the Switch On (Switch Off)
button. Besides you can see the scheduled events for this socket.

The socket shown on the Figure #6 is currently off, it will be turned
on automatically on the 27th of June at 9:59 and on the 28th of June at
10:59 it will be switched off again. The shown two events will be executed
periodically, with a loop period of 2 days.

18

All brands and logos are registered trademarks of their respective owners

SIS-PMS-LAN PROGRAMMABLE

SURGE

PROTECTOR WITH LAN INTERFACE

Figure #6

19

All brands and logos are registered trademarks of their respective owners

SIS-PMS-LAN PROGRAMMABLE

SURGE

PROTECTOR WITH LAN INTERFACE

Below the page you can see the current time of the web-server and
eventual information about the last successful timer synchronization.
Automatic timer synchronization is used if Use NTP for timer correction
option is enabled (see section 4.4 below).

NOTE: If a certain socket has a switching fault, e.g. it should be
switched on but the whole device is switched off, or it should be off but it
does have voltage, then the warning message Wrong voltage on socket!
will be shown above the Event schedule (see Figure #6 above). This
message might also indicate that this socket is defective.

For setting up the socket schedule click Set schedule button. You
will face then the page shown below (see Figure #7).

20

All brands and logos are registered trademarks of their respective owners