How it Works
Gemalto M2M
Loading...
PLS8 X
User Manual
40 pgs550.34 Kb0
Table of contents
Loading...

Gemalto M2M PLS8 X, PLS8 V User Manual

Cinterion® PLS8-X/PLS8-V
Hardware Interface Overview
Version: 03.009 DocId: PLS8-X_PLS8-V_HIO_v03.009
M2M.GEMALTO.COM
Cinterion® PLS8-X/PLS8-V Hardware Interface Overview
2
Page 2 of 40
Document Name: Version:
Date: DocId: Status
Cinterion® PLS8-X/PLS8-V Hardware Interface Overview
03.009 2015-08-04
03.009 Confidential / Preliminary
THE USE OF THE PRODUCT INCLUDING THE SOFTWARE AND DOCUMENTATION (THE "PROD­UCT") IS SUBJECT TO THE RELEASE NOTE PROVIDED TOGETHER WITH PRODUCT. IN ANY EVENT THE PROVISIONS OF THE RELEASE NOTE SHALL PREVAIL. THIS DOCUMENT CONTAINS INFORMATION ON GEMALTO M2M PRODUCTS. THE SPECIFICATIONS IN THIS DOCUMENT ARE SUBJECT TO CHANGE AT GEMALTO M2M'S DISCRETION. GEMALTO M2M GMBH GRANTS A NON­EXCLUSIVE RIGHT TO USE THE PRODUCT. THE RECIPIENT SHALL NOT TRANSFER, COPY, MODIFY, TRANSLATE, REVERSE ENGINEER, CREATE DERIVATIVE WORKS; DISASSEMBLE OR DECOMPILE THE PRODUCT OR OTHERWISE USE THE PRODUCT EXCEPT AS SPECIFICALLY AUTHORIZED. THE PRODUCT AND THIS DOCUMENT ARE PROVIDED ON AN "AS IS" BASIS ONLY AND MAY CONTAIN DEFICIENCIES OR INADEQUACIES. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, GEMALTO M2M GMBH DISCLAIMS ALL WARRANTIES AND LIABILITIES. THE RECIPIENT UNDERTAKES FOR AN UNLIMITED PERIOD OF TIME TO OBSERVE SECRECY REGARDING ANY INFORMATION AND DATA PROVIDED TO HIM IN THE CONTEXT OF THE DELIV­ERY OF THE PRODUCT. THIS GENERAL NOTE SHALL BE GOVERNED AND CONSTRUED ACCORDING TO GERMAN LAW.
Copyright
Transmittal, reproduction, dissemination and/or editing of this document as well as utilization of its con­tents and communication thereof to others without ex press autho rization are prohib ited. Offenders will be held liable for payment of damages. All rights created by patent grant or registration of a utility model or design patent are reserved.
Copyright © 2015, Gemalto M2M GmbH, a Gemalto Company
Trademark Notice
Gemalto, the Gemalto logo, are trademarks and service marks of Gemalto and are registered in certain countries. Microsoft and Win dows are e ither regis tered trademarks or trademarks of Microsoft Corpora­tion in the United States and/or other countries. All other register ed trademarks or trademarks mention ed in this document are property of their respective owners.
PLS8-X_PLS8-V_HIO_v03.009 2015-08-04
Confidential / Preliminary
Cinterion® PLS8-X/PLS8-V Hardware Interface Overview

Contents

40
Page 3 of 40
Contents
0 Document History.......................................................................................................6
1 Introduction.................................................................................................................7
1.1 Supported Products...........................................................................................7
1.2 Related Documents ...........................................................................................7
1.3 Terms and Abbreviations............ ........... .......... ........... ........... ............................7
1.4 Regulatory and Type Approval Information .....................................................10
1.4.1 Directives and Standards....................................................................10
1.4.2 SAR requirements specific to portable mobiles..................................12
1.4.3 SELV Requirements ...........................................................................13
1.4.4 Safety Precautions..............................................................................13
2 Product Concept.......................................................................................................14
2.1 Key Features at a Glance................................................................................14
2.2 PLS8-X/PLS8-V System Overview..................................................................17
3 Application Interface.................................................................................................18
3.1 Operating Modes .............................................................................................19
3.2 Power Supply...................................................................................................20
3.3 USB Interface...................................................................................................21
3.4 Serial Interface ASC0 ......................................................................................22
3.5 UICC/SIM/USIM Interface................................................................................23
3.6 Digital Audio Interface......................................................................................25
3.7 Analog-to-Digital Converter (ADC)...................................................................25
3.8 GPIO Interface.................................................................................................25
4 GNSS Receiver..........................................................................................................26
5 Antenna Interfaces....................................................................................................27
5.1 GSM/UMTS/LTE Antenna Interface.................................................................27
5.1.1 Antenna Installation ............................................................................28
5.2 GNSS Antenna Interface ................................................................................. 29
6 Mechanics..................................................................................................................31
6.1 Mechanical Dimensions of PLS8-X/PLS8-V....................................................31
7 Sample Application...................................................................................................33
8 Reference Approval..................................................................................................35
8.1 Reference Equipment for Type Approval.........................................................35
8.2 Compliance with FCC and IC Rules and Regulations ..................................... 36
9 Appendix....................................................................................................................38
9.1 List of Parts and Accessories...........................................................................38
PLS8-X_PLS8-V_HIO_v03.009 2015-08-04
Confidential / Preliminary
Cinterion® PLS8-X/PLS8-V Hardware Interface Overview

Tables

40
Page 4 of 40
Tables
Table 1: Directives ....................................................................................................... 10
Table 2: Standards of North American type approval.................................................. 10
Table 3: Requirements of quality ................................................................................. 10
Table 4: Standards of the Ministry of Information Industry of the
People’s Republic of China............................................................................ 11
Table 5: Toxic or hazardous substances or elements with defined concentration
limits............................................................................................................... 11
Table 6: Overview of operating modes ........................................................................ 19
Table 7: Signals of the SIM interface (SMT application interface)............................... 23
Table 8: Return loss in the active band........................................................................ 27
Table 9: Antenna gain limits for FCC and IC................................................................ 36
Table 10: List of parts and accessories.......................................................................... 38
Table 11: Molex sales contacts (subject to change)...................................................... 39
Table 12: Hirose sales contacts (subject to change)..................................................... 39
PLS8-X_PLS8-V_HIO_v03.009 2015-08-04
Confidential / Preliminary
Cinterion® PLS8-X/PLS8-V Hardware Interface Overview

Figures

40
Page 5 of 40
Figures
Figure 1: PLS8-X/PLS8-V system overview.................................................................. 17
Figure 2: Decoupling capacitor(s) for BATT+................................................................ 20
Figure 3: USB circuit..................................................................................................... 21
Figure 4: Serial interface ASC0..................................................................................... 22
Figure 5: First UICC/SIM/USIM interface...................................................................... 24
Figure 6: Second UICC/SIM/USIM interface................................................................. 24
Figure 7: Supply voltage for active GNSS antenna....................................................... 29
Figure 8: ESD protection for passive GNSS antenna................................................... 30
Figure 9: PLS8-X/PLS8-V – top and bottom view......................................................... 31
Figure 10: Dimensions of PLS8-X/PLS8-V (all dimensions in mm)................................. 32
Figure 11: PLS8-X/PLS8-V sample application............................................................... 34
Figure 12: Reference equipment for type approval......................................................... 35
PLS8-X_PLS8-V_HIO_v03.009 2015-08-04
Confidential / Preliminary
Cinterion® PLS8-X/PLS8-V Hardware Interface Overview

0 Document History

6
0 Document History
Page 6 of 40
Preceding document: "Cinterion® PLS8-X/PLS8-V Hardware Interface Overview" v02.510
®
New document: "Cinterion
Chapter What is new
1.4 Removed ECE-R 10 directive from Table 1.
Updated NAPRD version in Table 2.
5.2 Revised ratings for VGNSS in Figure 7.
8.2 Revised maximum antenna gain limits - added Table 9.
New document: "Cinterion
Chapter What is new
-- Initial document setup.
PLS8-X/PLS8-V Hardware Interface Overview" v03.009
®
PLS8-X/PLS8-V Hardware Interface Overview" v02.510
PLS8-X_PLS8-V_HIO_v03.009 2015-08-04
Confidential / Preliminary
Cinterion® PLS8-X/PLS8-V Hardware Interface Overview

1 Introduction

13
Page 7 of 40
1 Introduction
The document1 describes the hardware of the two Cinterion® modules variants PLS8-V and PLS8-X, designed to connect to a cellular device application and the air interface. It helps you quickly retrieve interface specifications, electrical and mechanical details and information on the requirements to be considered for integrating further components.
The product variants differ in their radio access technology support:
• PLS8-X is available for operation in LTE, UMTS and GSM radio networks - for supported frequency bands please refer to Section 2.1. Connected to this, the module has two sepa­rate firmware images on board that can be activated based on the used (U)SIM card. Employing the module’s two (U)SIM interfaces, it is thus possible to switch between firm­ware images on the fly - making PLS8-X a multi carrier/provider module.
• PLS8-V in contrast is available for operation in LTE radio networks only - for supported f re­quency bands please refer to Section 2.1. It has only a single firmware image on board that can be activated by (U)SIM card - making it a single carrier/provider module.
If not otherwise mentioned, this document applies to both product variants. Where necessary a note is made to differentiate between the variants.

1.1 Supported Products

This document applies to the following Gemalto M2M products:
•Cinterion
•Cinterion
®
PLS8-V module
®
PLS8-X module

1.2 Related Documents

[1] AT Command Set for your Gemalto M2M product [2] Release Notes for your Gemalto M2M product [3] Application Note 48: SMT Module Integration [4] Universal Serial Bus Specification Revision 2.0, April 27, 2000

1.3 Terms and Abbreviations

Abbreviation Description
ANSI American National Standards Institute ARP Antenna Reference Point CE Conformité Européene (European Conformity) CS Coding Scheme CS Circuit Switched CSD Circuit Switched Data
1.
The document is effective only if listed in the appropriate Release Notes as part of the technical documentation delivered with your Gemalto M2M product.
PLS8-X_PLS8-V_HIO_v03.009 2015-08-04
Confidential / Preliminary
Cinterion® PLS8-X/PLS8-V Hardware Interface Overview
1.3 Terms and Abbreviations
13
Abbreviation Description
DCS Digital Cellular System DL Download dnu Do not use DRX Discontinuous Reception DSB Development Support Board DTX Discontinuous Transmission EDGE Enhanced Data rates for GSM Evolution EGSM Extended GSM EMC Electromagnetic Compatibility ESD Electrostatic Discharge ETS European Telecommunication Standard ETSI European Telecommunications Standards Institute
Page 8 of 40
FCC Federal Communications Commission (U.S.) FDD Frequency Division Duplex GPRS General Packet Radio Service GSM Global Standard for Mobile Communications HiZ High Impedance HSDPA High Speed Downlink Packet Access I/O Input/Output IMEI International Mobile Equipment Identity ISO International Standards Organization ITU International Telecommunications Union kbps kbits per second LED Light Emitting Diode LGA Land Grid Array LTE Long term evolution MBB Moist ur e ba rr ier bag Mbps Mbits per second MCS Modulation and Coding Scheme MIMO Multiple Input Multiple Output MLCC Multi Layer Ceramic Capacitor MO Mobile Originated MS Mobile Station, also referred to as TE MSL Moisture Sensitivity Level MT Mobile Terminated nc Not connected
PLS8-X_PLS8-V_HIO_v03.009 2015-08-04
Confidential / Preliminary
Cinterion® PLS8-X/PLS8-V Hardware Interface Overview
1.3 Terms and Abbreviations
13
Abbreviation Description
NTC Negative Temperature Coefficient PCB Printed Circuit Board PCL Power Control Level PCS Personal Communication System, also referred to as GSM 1900 PD Pull Down resistor PDU Protocol Data Unit PS Packet Switched PSK Phase Shift Keying PU Pull Up resistor QAM Quadrature Amplitude Modulation R&TTE Radio and Telecommunication Terminal Equipment RF Radio Frequency
Page 9 of 40
rfu Reserved for future use ROPR Radio Output Power Reduction RTC Real Time Clock Rx Receive Direction SAR Specific Absorption Rate SELV Safety Extra Low Voltage SIM Subscriber Identification Module SMD Surface Mount Device SMS Short Message Service SMT Surface Mount Technology SRAM Static Random Access Memory SRB Signalling Radio Bearer TE Terminal Equipment TPC Transmit Power Control TS Technical Specification Tx Transmit Direction UL Upload UMTS Universal Mobile Telecommunications System URC Unsolicited Result Code USB Universal Serial Bus UICC USIM Integrated Circuit Card USIM UMTS Subscriber Identification Module WCDMA Wideband Code Division Multiple Access
PLS8-X_PLS8-V_HIO_v03.009 2015-08-04
Confidential / Preliminary
Cinterion® PLS8-X/PLS8-V Hardware Interface Overview

1.4 Regulatory and Type Approval Information

13
Page 10 of 40
1.4 Regulatory and Type Approval Information

1.4.1 Directives and Standards

PLS8-X/PLS8-V has been designed to comply with the directives and standards listed below. It is the responsibility of the application manufacturer to ensure compliance of the final product
with all provisions of the applicable directives and standards as well as with the technical spec­ifications provided in the "PLS8-X/PLS8-V Hardware Interface Description".
Table 1: Directives
1
2002/95/EC (RoHS 1) 2011/65/EC (RoHS 2)
Table 2: Standards of North American type approval
CFR Title 47 Code of Federal Regulations, Part 22, Part 24 and Part 27; US Equipmen t
OET Bulletin 65 (Edition 97-01)
UL 60 950-1 Product Safety Certification (Safety requirements)
NAPRD.03 V5.23 Overview of PCS Type certification review board Mobile Equipment Type
RSS132, RSS133, RSS139
Directive of the European Parliament and of the Council of 27 January 2003 (and revised on 8 June 2011) on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS)
Authorization FCC Evaluating Compliance with FCC Guidelines for Human Exposure to Radio-
frequency Electromagnetic Fields
Certification and IMEI control PCS Type Certification Review board (PTCRB)
Canadian Standard
Table 3: Requirements of quality
IEC 60068 Environmental testing DIN EN 60529 IP codes
1.
Manufacturers of applications which can be used in the US shall en sure that their applications have a PTCRB approval. For this purpose they can refer to the PTCRB approval of the respective module.
PLS8-X_PLS8-V_HIO_v03.009 2015-08-04
Confidential / Preliminary
Cinterion® PLS8-X/PLS8-V Hardware Interface Overview
1.4 Regulatory and Type Approval Information
13
Table 4: Standards of the Ministry of Information Industry of the People’s Republic of China
SJ/T 11363-2006 “Requirements for Concentration Limits for Certain Hazardous Substances
in Electronic Information Products” (2006-06).
SJ/T 11364-2006 “Marking for Control of Pollution Caused by Electronic
Information Products” (2006-06). According to the “Chinese Administration on th e Control of
Pollution caused by Electronic Information Products” (ACPEIP) the EPUP, i.e., Environmental Protection Use Period, of this product is 20 years as per the symbol shown here, unless otherwise marked. The EPUP is valid only as long as the product is operated within the operating limits described in the Hardware Interface Description.
Please see Table 5 for an overview of toxic or hazardous substances or ele­ments that might be contained in product parts in concentrations above the limits defined by SJ/T 11363-2006.
Page 11 of 40
Table 5: Toxic or hazardous substances or elements with defined concentration limits
PLS8-X_PLS8-V_HIO_v03.009 2015-08-04
Confidential / Preliminary
Cinterion® PLS8-X/PLS8-V Hardware Interface Overview
1.4 Regulatory and Type Approval Information
13
Page 12 of 40

1.4.2 SAR requirements specific to portable mobiles

Mobile phones, PDAs or other portable transmitters and receivers incorporating a GSM module must be in accordance with the guidelines for human exposure to radio frequency energy. This requires the Specific Absorption Rate (SAR) of portable PLS8-X/ PLS8-V based applications to be evaluated and approved for compliance with national and/or international regulations.
Since the SAR value varies significantly with the individual product design manufacturers are advised to submit their product for approval if designed for portable use. For US markets the relevant directives are mentioned below. It is the responsibility of the manufacturer of the final product to verify whether or not further standards, recommendations or directives are in force outside these areas.
Products intended for sale on US markets
ES 59005/ANSI C95.1 Considerations for evaluation of human exposure to electromagnetic
fields (EMFs) from mobile telecommunication equipment (MTE) in the frequency range 30MHz - 6GHz
IMPORTANT: Manufacturers of portable applications based on PLS8-X/PLS8-V modules are required to have their final product certified and apply for their own FCC Grant and Industry Canada Cer­tificate related to the specific portable mobile.
PLS8-X_PLS8-V_HIO_v03.009 2015-08-04
Confidential / Preliminary
Loading...
+ 28 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use