GE Lighting WGZ100 User Manual

210*290mm

0-10V LED Driver

ZigBee to 0-10V Interface

Driver Line (L)

Driver Neutral (N)

Wire Nut

(N)

(L)

Driver 0-10V Dimming Wires

Driver LED Output Wires

(

(+)

(-)

Fixture Mains

(

Fixture Driver Housing

(

(+)

(-)

The interface and wiring is intended to be installed and

completely enclosed within the same NEC Class

housing as the

(

(Relay Output)

(L)

(N)

(Relay Output)

(N)

(L)

Lighting Solutions

ZigBee

正面 背面

STOP

BEFORE YOU BEGIN

Read these instructions completely and carefully.

WARNING/AVERTISSEMENT

RISK OF ELECTRIC SHOCK

Turn power off before inspection, installation or removal.

Properly ground electrical enclosure.

RISK OF ELECTRIC SHOCK

Follow all NEC and local codes.
Use only UL approved wire for input/output connections.
Minimum size 14 AWG for continuous runs.

RISQUES DE DÉCHARGES ÉLECTRIQUES

Coupez l'alimentation avant d'inspecter, installer ou déplacer le luminaire.
Assurez-vous de correctement mettre à la terre le boitier d'alimentation électrique.

RISQUES D'INCENDIE

Respectez tous les codes NEC et codes locaux.
N'utilisez que des fils approuvés par UL pour les entrées / sorties de
connexion. Taille minimum 14 AWG.

Save These Instructions

Use only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.

WGZ100

or code-compliant wiring box)

24-14

for P2 terminal

Left : (N)Input、(L)Input、(L)Relay Output
Right : 0-10V GND、0-10V OUT、Dali+、Dali-

32mA

or LED Driver

Translate Wireless ZigBee messaging to control electronic ballast or LED Driver:

via code-compliant conduit)

1 driver

not provided).

0-10V driver using metal mounting screws

to LED Array)

Type 1.B action Pollution degree 2 Rated Impulse voltage 4000V

(N) Input White

(L) Input Black

(L) Relay Output Red

(-) 0-10V GND Grey

(+) 0-10V OUT Purple

Caution: The user is cautioned that changes or modifications not expressly approved by the party
responsible for compliance could
void the user's authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be
installed and operated with a minimum distance of 20cm between the radiator and any part of your body.

This device complies with Industry Canada’s license exempt RSSs. Operation is subject to the following two
conditions:
(1) This device may not cause interference
(2) This device must accept any interference, including interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est
autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled
environment. This equipment should
be installed and operated with a minimum distance of 20cm between the radiator and any part of your
body.

Pour se conformer aux exigences de conformité CNR 102 RF exposition, une distance de séparation d'au
moins 20 cm doit être maintenue
entre l'antenne de cet appareil ettoutes les personnes.

FCC sDoC statement

FCC Supplier’s Declaration of Conformity

Brand name: GE Lighting / model number: WGZ100
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may
cause undesired operation.
Suppliers Name: GE Lighting Solutions
Suppliers Address (USA): Nela Park, Cleveland, Ohio, 44112
Suppliers phone number and / or internet contact information: 1-888-MYGELED