
CM
LOAD CELL FOR COMPRESSION APPLICATIONS
MECHANICAL DIMENSIONS
Main features
• Range of measurement: from 100 to 50.000 Kg
• Accuracy class: 0,2%
• All stainless steel construction
• Corrosion resistant
• Internally generated calibration signal
• Grade of protection: IP67 (DIN 40050)
CM series load cells are strain gauge transducers used to
measure loads in static and dynamic applications, in
compression, with high accuracy.
They are machined from a single block of metal, so the
primary sensing element, the mountings and the case
contain no welds allowing smaller dimensions and an
enhanced grade of protection. The configuration of the point
of measurement, with 8 strain gauges, reduces errors caused
by imperfect applications of the load.
Typical applications of load cells connected in parallel are:
silos, hoppers, large weighing platforms.
The stainless steel construction is suitable for use in
aggressive environments in the chemical and petrochemical
industries.
ø A
ø B
ø C
ø D
E
H
K
L
L1
L2
ø M
ø N
R
VITI
Nm*
TECHNICAL DATA
0,2%
100...50.000 Kg
2mV/V
<± 0,2% FSO
< ± 0,2% FSO
< ± 0,06% FSO
< ± 1% FSO
80%FSO ± 1%
< ± 0,01% FSO°C
< ± 0,01% FSO°C
< ± 0,01% FSO°C
700 Ohm
700 Ohm
> 10 GOhm
10 V
15 V
-10...+50°C
-20...+60°C
-30...+80°C
130% Ln
100% Ln
150% Ln
> 300% Ln
< 0,2 mm
Cable: IP67
Connector: IP65
VPT02A10-6PT2
6x0,25 / 5 m.
Stainless steel
Accuracy
Nominal full scale load (Ln)
Nominal output at FSO
Output tolerance at Ln
Combined errors: Non linearity
Histeresis, Repeatibility
Creep (after 30 min. at Ln)
Zero load out of balance signal
Calibration signal *
Thermal drift in Sensitivity
compensated Zero
range Calibration
Nominal input resistance
Nominal output resistance
Isolation resistance
Nominal supply voltage
Maximum supply voltage
Compensated temperature range
Maximum temperature range
Storage temperature range
Permitted static load
Permitted dinamic load
Maximum applicable load
Rupture load
Maximum elastic deformation at Ln
Grade of protection (DIN40050)
Electr. connections: Connector
Screened cable
Elastic element material
* The exact value is indicated on the instrument nameplate
100
2000
87
6,5
10,5
100
6
11,7
15,7
45,7
30
13,5
20
24
30
6XM6
9
3500
7000
98,5
10,5
16,5
120
10
17,5
21,5
51,5
30
13,5
24
30
30
6XM10
60
10000
30000
102,2
13
19
126
12,5
14
54
40
17
35
50
6XM12
100
50000
125
17
25
155
16,5
16
77
61
27
45
-
100
6XM16
200
Ln (Kg)
Dimensions mm. (± 0,1) * Recommended torque with UNI 5931 screws of
resistance class 10.9 according to UNI 3740.
LOAD
INTRODUCTION
DIRECTION
BALL R
BALL R

ELECTRICAL CONNECTIONS
CONVERSION TABLE
If the transducer is supplied complete with
prewired connection cable, the colour code
is that indicated in the table.
Cells connected in parallel
In systems that use several cells, the parallel connection automatically sums the loads on each individual cell.
Using this method of measurement, the maximum load will be the sum of the loads on the individual cells and the
sensitivity will be the average value of these cells.
It is important that the user ensures that no cell is stessed beyond its maximum rating under any load condition.
Kg
1
0.102
0.454
N
9.807
1
4.448
Lb
2.205
0.225
1
* The screen is isolated from the
transducer body.
It is recommended that the ground is
connected at the instrument end.
6x0.25 Screened cable
VPT02A10-6PT2
MALE CONNECTOR
SIGNAL +
SIGNAL EXCITATION +
EXCITATION -
CALIBRATION SHUNT
CONNECTOR
OUTPUT
CABLE
OUTPUT
Red
Black
White
Green
Blue-Orange
Red
Yellow or Black
White
Green
Yellow-Green
Red
Yellow or Black
White
Green
Yellow-Green
Yellow-Green
Red
Yellow or Black
White
Green
SHUNT BOX

GEFRAN spa reserves the right to make any kind of design or functional modification at any moment without prior notice.
ORDER CODE
Ex.: CM - K10M - F - S
CM load cell, range 0 - 10.000 kg, cable connection and 2mV/V standard sensitivity.
SENSITIVITY
2mV/V version
S
ELECTRICAL CONNECTIONS
VPT02A10-6PT2 connector
C
If request, it is possible to
supply models with non-standard mechanical and/or
electrical features.
Load cell CM
0 - 500 K5C
0 - 350 K3.5C
MEASUREMENT RANGE (Kg)
0 - 100
0 - 200
K1C
K2C
0 - 700 K7C
6x0,25 5m screened cable
OPTIONAL ACCESSORIES
Female cable connector Grade of protection IP65 CON 300
6-pin connector with 8m (25ft) cable C08W
6-pin connector with 15m (50ft) cable C15W
6-pin connector with 25m (75ft) cable C25W
6-pin connector with 30m (100ft) cable C30W
Other lengths consult factory
Self alignement plate
(Max. inclination 3°)
0 - 1000 K1M
F
3mV/V version (range
500...5000Kg) only
R
ø A
ø B
ø C
D
F
E
COD
≤ 2000
100
74
24
20
11
1,25
PIA700
≤ 7000
120
100
28
25
12
1,5
PIA701
≤ 30000
126
105
37
32
22
2
PIA702
≤ 50000
155
130
47
50
39
3
PIA703
NOMINAL LOAD Kg
Dimensions mm. (± 0,1)
0 - 2000 K2M
0 - 3500 K3.5M
0 - 5000 K5M
0 - 7000 K7M
0 - 10000 K10M
0 - 20000 K20M
0 - 30000 K30M
0 - 50000 K50M
Cable colour code
Conn. wires
A
B
C
D
E
F
Red
Black
White
Green
Blue
Orange
DTS_CM_0709_ENG