Page 1
HDMI • 1000HD
USER MANUAL
www.gefen.com
Page 2
ASKING FOR ASSISTANCE
Technical Support:
Telephone (818) 772-9100
(800) 545-6900
Fax (818) 772-9120
Technical Support Hours:
8:00 AM to 5:00 PM Monday thru Friday.
Write To:
Gefen Inc.
C/O Customer Service
20600 Nordhoff St
Chatsworth, CA 91311
www.gefen.com
support@gefen.com
Gefen Inc. reserves the right to make changes in the hardware, packaging and any
accompanying documentation without prior written notice.
The HDMI 1000 is a trademark of Gefen Inc.
© 2007 Gefen Inc., All Rights Reserved
Notice
Page 3
TABLE OF CONTENTS
1
Introduction
2
Front Panel Descriptions
3
Back Panel Descriptions
4
How To Connect The HDMI 1000
5
How To Connect The HDMI 1000 (w/o DDC)
6
HDMI 1000 Wiring Diagram
7
Specications
8
Warranty
Page 4
OPERATION NOTES
READ THESE NOTES BEFORE INSTALLING
OR OPERATING THE HDMI 1000
• The ber optics cable must be treated carefully when connectors are exposed. They
are susceptible to dust which can contribute to loss of pixels.
• The HDMI 1000 works for all HDMI displays and supports resolutions up to
1920x1200 or 1080p
• The HDMI 1000 is housed in a metal box for better RF shielding.
• Fully HDMI 1.2 compliant
• Uses CAT-5 cable for HDCP/DDC and control signals.
Page 5
INTRODUCTION
Thank you for purchasing Gefen’ s ex•tend•it HDMI 1000. The HDMI 1000 allows extension of HDMI up to 1640 feet without losing any quality.
CONTENTS
The HDMI 1000 consists of:
(1) HDMI 1000S
(1) HDMI 1000R
(1) HDMI cable (6FT)
(1) 12VDC Power Supply
(1) User's Manual
1
Page 6
FRONT PANELS DESCRIPTIONS
HDMI 1000 Sender (Front View Only)
Power LED indicates the unit is powered
Status LED indicates a link
Red
between the sender and receiver
HDMI 1000 Receiver (Front View Only)
Power LED indicates the unit is powered
Green
Blue
Clock
HDCP & DDC Signals
Status LED indicates a link
between the sender and receiver
Green
Red
2
Clock
Blue
HDCP & DDC Signals
Page 7
BACK PANELS DESCRIPTIONS
HDMI 1000 Sender (Rear View Only)
HDMI Input
12 VDC Input
HDMI 1000 Receiver (Rear View Only)
HDMI Output
12 VDC Input
3
Page 8
HOW TO CONNECT THE HDMI 1000
Connect the HDMI 1000 sender unit to the HDMI source using the supplied cables.
1
Connect the HDMI 1000 receiver unit to your HDMI display.
2
Connect the four ber optics and one CAT5 cable between the sender and receiver.
3
Plug the 12VDC power supplies into the HDMI 1000 receiver.
4
You should see a beautiful picture.
5
* Cable Requirement - 50 or 62.5 micron multimode ber optics cable
4
Page 9
HOW TO CONNECT THE HDMI 1000 (w/o DDC)
The HDMI 1000HD can be hooked up without using the CAT5 if DDC is not needed. A
second power supply will be required to power the receiver unit in this setup.
For computer extensions where EDID is needed, a DVI Detective can be purchased to
store the EDID of the display.
Connect the HDMI 1000 sender unit to the HDMI source using the supplied cables.
1
Connect the HDMI 1000 receiver unit to your HDMI display.
2
Connect the four ber optics between the sender and receiver.
3
Plug the 12VDC power supplies into the HDMI 1000 sender.
4
Plug the 12VDC power supplies into the HDMI 1000 receiver.
5
If using a HDMI Detective attach it in between the computer and the sender
6
You should see a beautiful picture.
7
* Cable Requirement - 50 or 62.5 micron multimode ber optics cable
5
Page 10
HDMI 1000 WIRING DIAGRAM
6
Page 11
SPECIFICATIONS
Video Amplier Bandwidth ................................................................................ 1.65 Gbps
Input Video Signal ......................................................................................... 1.2 volts p-p
Input DDC Signal .................................................................................... 5 volts p-p (TTL)
Single Link Range ......................................................................................... 1920 x 1200
Input/Output Connector Type ................................................................................... HDMI
Link Connector ........................................................................................................ RJ-45
Fiber Requirement ....................................................... 50 or 62.5 micron multimode ber
Power Consumption ................................................................................ 15 Watts (max.)
Power Supply ........................................................................................................ 12VDC
Dimensions .................................................................................. 3.25”D x 4.25 ”W x 1”H
Shipping Weight ....................................................................................................... 5 lbs.
7
Loading...