®
VGA Extender LR
EXT-VGA-141LR
User’s Manual
ASKING FOR ASSISTANCE
Technical Support:
Telephone (818) 772-9100
(800) 545-6900
Fax (818) 772-9120
Technical Support Hours:
8:00 AM to 5:00 PM Monday thru Friday Pacic Time
Write To:
Gefen, LLC.
c/o Customer Service
20600 Nordhoff St
Chatsworth, CA 91311
www.gefen.com
support@gefen.com
Notice
Gefen, LLC. reserves the right to make changes in the hardware, packaging and
any accompanying documentation without prior written notice.
VGA Extender LR is a trademark of Gefen, LLC.
© 2011 Gefen, LLC. All rights reserved.
All trademarks are the property of their respective owners.
Rev A3
CONTENTS
1 Introduction
2 Operation Notes
3 Features
4 Panel Layout
5 Panel Descriptions
6 Connecting And Operating The VGA Extender LR
7 Connecting And Operating The VGA Extender LR
8 Network Cable Wiring Diagram
9 Specications
10 Warranty
INTRODUCTION
Congratulations on your purchase of the VGA Extender LR. Your complete
satisfaction is very important to us.
Gefen
Gefen delivers innovative, progressive computer and electronics add-on solutions
that harness integration, extension, distribution and conversion technologies.
Gefen’s reliable, plug-and-play products supplement cross-platform computer
systems, professional audio/video environments and HDTV systems of all sizes
with hard-working solutions that are easy to implement and simple to operate.
The Gefen VGA Extender LR
The VGA Extender allows users to extend video signals beyond the A/V rack.
The VGA Extender Series can be used to extend an analog signal to cover
distances up to 330 feet. Industry standard Category 5e (CAT-5e) cable is used
for the extension.
How It Works
The VGA Extender LR Sender unit connects to your source using the supplied
cable. The Receiver unit connects to your display – up to 330 feet away. One
CAT-5 cable connects the Sender and the Receiver to each other, extending your
video awlessly.
Note: This is a new VGA Extender that goes double the distance of the previous
version, and also has a trim pot for ne video adjustment.
1
OPERATION NOTES
READ THESE NOTES BEFORE INSTALLING OR
OPERATING THE VGA EXTENDER LR
• Display information (EDID) is not sent back to the source. Standard VESA
resolutions should be output by most computers without the need of an
EDID. If using a non-VESA standard resolution or if EDID is needed, an
EDID storage and relay device is necessary. Gefen recommends the use of
a DVI Detective (part# EXT-DVI-EDID, EXT-DVI-EDIDN, or EXT-DVI-EDIDP)
with two VGA to DVI adapters.
• Use industry standard Category-5 (CAT-5) cable to operate the VGA
Extender LR system. CAT-5e cable is preferred.
• Please connect all the cables between the computer and the VGA Extender
LR before powering up the VGA Extender LR unit.
• The VGA Extender LR units are housed in a metal box for better RF
shielding.
2
FEATURES
Features
• Extends any VGA or high denition component display up to 330 feet (100
meters)
• One CAT-5e cable for extension
• Supports resolutions up to 1080p, 2K, and 1920 x 1200
Package Includes
(1) VGA Extender S Sender Unit
(1) VGA Extender R Receive Unit
(1) 6 Foot VGA cable (M-F)
(1) 5V external power supply
(1) Quick-Start Guide
3
PANEL LAYOUT
1 2
4
3
5
6
7
4
PANEL DESCRIPTIONS
1 5V DC Power Supply Input
Connect the included 5V DC power supply to this input. Power for the receiving
unit will be provided over the CAT-5e cable that connects the sending and
receiving units together.
2 Sender RJ-45 Input
Connect a CAT-5e cable (terminated according to the TIA/EIA-568-B
specication. Please see page 7) between the sending and receiving units.
3 VGA Input
Connect the VGA source to this input. EDID is not transmitted from the display
through the VGA Extender LR units. If the display has a non-standard VESA
resolution, please purchase an EDID storage device (part# EXT-DVI-EDIDN) to
record and transmit the displays EDID back to the source.
4 Brightness Trim Pot Control
Adjusting this control will brighten or dim the output video. Please see page 6 for
more details.
5 Receiver RJ-45 Input
Connect a CAT-5e cable (terminated according to the TIA/EIA-568-B
specication. Please see page 7) between the sending and receiving units.
6 Power LED
This LED will become active once the included power supply is connected and a
properly connected CAT-5e cable is joining the sending and receiving units.
7 VGA Output
Connect the VGA display to this output port.
5
CONNECTING AND OPERATING THE VGA EXTENDER LR
How to Connect the VGA Extender LR
1. Connect the VGA Extender LR Sender unit to the VGA output on the back of
your computer. The six foot M-F VGA cable connects the CPU and Sender
unit together.
2. Connect the VGA Extender LR Receiver unit to your monitor with the VGA
cable that is attached to your monitor.
3. Connect the CAT-5e cable between the VGA Extender LR Sender and
Receiver’s CAT5 input.
4. Plug the 5V DC power supply into the Sender unit. The VGA Extender LR
Receiver will draw power from the Sender.
BRIGHTNESS ADJUSTMENT CONTROL
A brightness adjustment control (or “trim pot”) is found on the Receiver unit and
will help compensate for issues that can be introduced by outside interference
and cable variances. If the outgoing image is too dark or too bright, the brightness trim pot can be tuned to help brighten the image. To use the brightness
trim pot, insert a small philips screwdriver into the brightness trim pot hole. Turn
the trim pot in small increments in either a clockwise or counterclockwise direction until the desired brightness is reached. Do not force the trim pot to turn if
resistance is encountered; turn it the other way instead. Forcing the trim pot may
render the product inoperative.
CABLE SKEW / COLOR CONVERGENCE ADJUSTMENTS
In order to reduce the amount of crosstalk between twisted pairs within the CAT5
cable, the rate of twist for each pair is varied. The rate of twist affects the length
of each twisted pair and is referred to as CABLE SKEW. Slight differences in
cable skew between pairs of wire can result in undesirable color separation.
The EXT-VGA-LR allows you to manually compensate for cable skew. Underneath the Receiver unit, there are a group of DIP switches. These switches are
pre-set to optimal values at the factory but can easily be changed to correct color
smearing or separation. To use the DIP switches, peel back the small strip of
silver-grey tape. The exposed small sliding switches can be turned ON or OFF
with a small pointed instrument such as a very small screwdriver or the head of a
mechanical pencil (without lead exposed). The DIP switch banks and instructions
for their use are shown on the next page.
6
CONNECTING AND OPERATING THE VGA EXTENDER LR CONT’D
Using DIP Switches to Compensate for Video Issues
The rst step in adjusting the video quality is to display text and a graphic on your monitor
(i.e. desktop icons). Then set your computer to the resolution that you will be using most
frequently. Set the DIP (Dual Inline Package) switches to the settings that are recommended
for the different lengths of CAT5 cable (see chart below). Verify that the picture quality is
to your satisfaction. If the recommended setting does not produce a great quality picture,
try using a different DIP switch setting.
The three DIP switch banks affect the primary colors Red, Green and Blue directly and are
thus labelled accordingly. Should you nd a problem with too much or too little or a certain
color present in the output video, begin adjustments in the DIP switch bank corresponding
to the color that is present/absent too much.
The settings shown below are our recommendations for best performance.
0-25 Feet All DIP switches are set to OFF for all colors.
26-100 Feet Set DIP switch #1 ON for all colors. 2,3,4 remain OFF.
101-200 Feet Set DIP switch #2 ON for all colors. 1,3,4 remain OFF.
201-300 Feet Set DIP switch #3 ON for all colors. 1,2,4 remain OFF.
301 Feet and Up Set DIP switch #4 ON for all colors. 1,2,3,remain OFF.
NOTE: A DIP switch is set to the OFF position when the switch is closest to the number
printed immediately below it. The word “ON” will be printed at the top of the DIP switch
bank, usually in the lefthand upper corner.
NOTE: The default position of the DIP switches is that of the 26-100 Feet setting
above with DIP Switch #1 ON for all colors and switches 2,3,4 OFF.
Underside of Receiver Unit
DIP Switch Bank for Video Adjustments
ON DIP
1 2 3 4
RED
ON DIP
1 2 3 4
7
GREEN
ON DIP
BLUE
1 2 3 4
NETWORK CABLE WIRING DIAGRAM
Gefen has specically engineered their products to work with the TIA/EIA-568-B
specication. Please adhere to the table below when eld terminating cable for
use with Gefen products. Failure to do so may produce unexpected results and
reduced performance.
Pin Color
1 Orange / White
2 Orange
3 Green / White
4 Blue
5 Blue / White
6 Green
7 Brown / White
8 Brown
CAT-5 and CAT-5e cabling comes in stranded and solid core types. Gefen
recommends using solid core cabling. CAT-5e cable is recommended for best
results.
Each cable run must be one continuous run from one end to the other. No splices
or use of punch down blocks.
1 2 3 4 5 6 7 8
8
SPECIFICATIONS
Video Amplier Bandwidth ....................................................................... 350 MHz
Input Video Signal .............................................................................. 1.2 Volts p-p
Input Sync Signal ........................................................................ 5 Volts p-p (TTL)
Horizontal Frequency Range................................................................. 15-70 KHz
Vertical Frequency Range.................................................................... 30-170 KHz
Video In ....................................................................................................... HD-15
Focus ................................................................................................. 25 to 330 FT
Video out ..................................................................................................... HD-15
Link Connector ............................................................................................. RJ-45
Power Consumption ................................................................ 5W (per unit, max.)
Power Supply ............................................................................... 5VDC (External)
Dimensions .......................................................................... 1.9”H x 1.6”W x 3.5”D
Shipping Weight ............................................................................................ 2 Lbs
9
WARRANTY
Gefen warrants the equipment it manufactures to be free from defects in material
and workmanship.
If equipment fails because of such defects and Gefen is notied within two (2)
years from the date of shipment, Gefen will, at its option, repair or replace the
equipment, provided that the equipment has not been subjected to mechanical,
electrical, or other abuse or modications. Equipment that fails under conditions
other than those covered will be repaired at the current price of parts and labor in
effect at the time of repair. Such repairs are warranted for ninety (90) days from
the day of reshipment to the Buyer.
This warranty is in lieu of all other warranties expressed or implied, including
without limitation, any implied warranty or merchantability or tness for any
particular purpose, all of which are expressly disclaimed.
1. Proof of sale may be required in order to claim warranty.
2. Customers outside the US are responsible for shipping charges to and from
Gefen.
3. Copper cables are limited to a 30 day warranty and cables must be in their
original condition.
The information in this manual has been carefully checked and is believed to
be accurate. However, Gefen assumes no responsibility for any inaccuracies
that may be contained in this manual. In no event will Gefen be liable for
direct, indirect, special, incidental, or consequential damages resulting from
any defect or omission in this manual, even if advised of the possibility of such
damages. The technical information contained herein regarding the features and
specications is subject to change without notice.
For the latest warranty coverage information, refer to the Warranty and Return
Policy under the Support section of the Gefen Web site at www.gefen.com.
PRODUCT REGISTRATION
Please register your product online by visiting the Register Product page
under the Support section of the Gefen Web site.
10
*ma-VGA-141LR*
Rev A3
20600 Nordhoff St., Chatsworth CA 91311
1-800-545-6900 818-772-9100 fax: 818-772-9120
www.gefen.com support@gefen.com
Pb
This product uses UL listed power supplies.
Loading...