Gefen EXT-UHD600-12 User Manual
1:2 Splitter for HDMI w/HDR
*Preferred
4K ULTRA
EXT-UHD600-12
User Manual
Release A1
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this product near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install or place this product near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong are provided for
your safety. If the provided plug does not t into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specied by the manufacturer.
12. To reduce the risk of electric shock and/or damage to this product, never handle or
touch this unit or power cord if your hands are wet or damp. Do not expose this
product to rain or moisture.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualied service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally,
or has been dropped.
15. Batteries that may be included with this product and/or accessories should never be
exposed to open ame or excessive heat. Always dispose of used batteries
according to the instructions.
ii
Warranty Information
Gefen warrants the equipment it manufactures to be free from defects in material and
workmanship.
If equipment fails because of such defects and Gefen is notied within two (2) years from
the date of shipment, Gefen will, at its option, repair or replace the equipment, provided
that the equipment has not been subjected to mechanical, electrical, or other abuse or
modications. Equipment that fails under conditions other than those covered will be
repaired at the current price of parts and labor in effect at the time of repair. Such repairs
are warranted for ninety (90) days from the day of reshipment to the Buyer.
This warranty is in lieu of all other warranties expressed or implied, including without
limitation, any implied warranty or merchantability or tness for any particular purpose, all of
which are expressly disclaimed.
1. Proof of sale may be required in order to claim warranty.
2. Customers outside the US are responsible for shipping charges to and from Gefen.
3. Copper cables are limited to a 30 day warranty and cables must be in their original
condition.
The information in this manual has been carefully checked and is believed to be accurate.
However, Gefen assumes no responsibility for any inaccuracies that may be contained
in this manual. In no event will Gefen be liable for direct, indirect, special, incidental, or
consequential damages resulting from any defect or omission in this manual, even if
advised of the possibility of such damages. The technical information contained herein
regarding the features and specications is subject to change without notice.
For the latest warranty coverage information, refer to the Warranty and Return Policy under
the Support section of the Gefen Web site at www.gefen.com.
iii
Licensing
This product uses software that is subject to open source licenses, including one or more
of the General Public License Version 2 and Version 2.1, Lesser General Public License
Version 2.1 and Version 3, BSD, and BSD-style licenses. Distribution and use of this
product is subject to the license terms and limitations of liability provided in those licenses.
Specic license terms and Copyright Notications are provided in the source code.
For three years from date of activation of this product, any party may request, and we
will supply, for software covered by an applicable license (e.g. GPL or LGPL), a complete
machine-readable copy of the corresponding open source code on a medium customarily
used for software interchange. The following software and libraries are included with this
product and subject to their respective open source licenses:
• jQuery
• Linux
iv
Contacting Gefen Technical Support
Technical Support
(707) 283-5900 (800) 472-5555
8:00 AM to 5:00 PM Monday - Friday, Pacic Time
Email
support@gefen.com
Web
http://www.gefen.com
Mailing Address
Gefen
Core Brands, LLC
c/o Customer Service
1800 S McDowell Blvd
Petaluma, CA 94954 USA
Product Registration
Register your product here: http://www.gefen.com/kvm/Registry/Registration.jsp
v
Operating Notes
• The Gefen Syner-G Software Suite is a free downloadable application from Gefen
that provides a variety of useful tools, including automatic download and installation of
rmware upgrades for this product. Always make sure that this product is running the
latest rmware.
Important
Cable quality is critical when handling 600 MHz HDMI signals. It is highly
recommend that Gefen Locking HDMI cables be used in the installation.
Gefen HDMI cables have been designed and tested to work at 600 MHz
and reliably transport the full 18 Gbps throughput of HDMI 2.0.
Ultra HD 600 MHz 1:2 Splitter for HDMI w/HDR is a trademark of Gefen, LLC.
© 2016 Core Brands, LLC. All Rights Reserved. All trademarks are the property of their respective owners.
Gefen, LLC reserves the right to make changes in the hardware, packaging, and any accompanying documentation
This product uses UL-Listed power supplies
without prior written notice.
vi
vi
Features and Packing List
2.2
60Hz, 4:4:4
600 MHz
4K ULTRA
4K
DCI, 4096 x 2160, 30Hz
Features
• Simultaneously displays an Ultra Hi-Def source on up to two Ultra HD displays
• Specically designed to support multiple layers of splitting/cascading in large video
distribution and signage applications, supporting hundreds of displays
• Supports resolutions up to 4K DCI-Cinema (4096 x 2160 at 60 Hz, 4:4:4 color space),
4K Ultra HD (3860 x 2160 at 60Hz, 4:4:4 color space), 1080p Full HD, and 1920x1200
WUXGA
• Supports HDR (High Dynamic Range) 10-bit Deep Color at 4K 4:4:4
• Supports 12-bit Deep Color at 1080p 4:4:4
• 3DTV pass-through
• Lip Sync pass-through
• EDID Management and Audio Mode selectors for rapid integration of source and
displays
• Supports LPCM 7.1, Dolby Atmos®, Dolby® TrueHD, DTS:X™, and DTS-HD Master
Audio™
• Supports the use of DVI sources and DVI displays with HDMI-to-DVI adapters (not
included)
• Advanced EDID Management via USB, using the Gefen Syner-G™ software
• In-eld rmware update via USB, using the Gefen Syner-G™ software
• Long Reach Power (LRP) provides 500 mA at 5V on pin 18 of HDMI outputs 1 and 2.
Enables select extender devices to be powered through their HDMI input port.
• Locking power connector
• Low-prole, surface-mountable enclosure
H
D
R
High Dynamic Range
CINEMA
DCI, 4096 x 2160, 30Hz
Deep Color Support
vii
Features and Packing List
Packing List
The Ultra HD 600 MHz 1:2 Splitter for HDMI w/ HDR ships with the items listed below.
The packing contents of the Sender and Receiver unit are listed below. If any of these
items are not present in the box when you rst open it, immediately contact your dealer or
Gefen.
• 1 x Ultra HD 600 MHz 1:2 Splitter for HDMI w/ HDR
• 1 x 6 ft locking HDMI cable
• 1 x 5V Power Supply w US/EU/UK/AU plugs
• 2 x Surface Mounting L-Brackets
• 4 x M3 6 mm Machine screws for mounting the L-Brackets to unit
• 2 x 6-32 5 mm Machine screws for mounting the unit to Gefen EXT-RACK-1U-GRY
(available separately)
• 4 x Self-Adhesive Rubber Feet
• 1 x Quick-Start Guide
viii
Table of Contents
1 Getting Started
Introduction............................................................................................................ 2
Front Panel .................................................................................................... 2
Rear Panel .................................................................................................... 3
Installation ............................................................................................................. 4
Connection Instructions ................................................................................. 4
Sample Application Diagram ......................................................................... 5
2 Basic Operation
EDID Management ................................................................................................ 8
EDID Modes .................................................................................................. 8
Output LED Status ................................................................................................ 9
3 Advanced Operation
Using Syner-G™ ................................................................................................. 12
Verifying the USB Driver ............................................................................. 12
Setting the EDID Mode ............................................................................... 14
Downloading an EDID ................................................................................. 15
Uploading an EDID ..................................................................................... 17
Copying an EDID ........................................................................................ 19
Viewing an EDID ......................................................................................... 21
Resetting to Factory Defaults ...................................................................... 25
Viewing Signal Status ................................................................................. 26
HDCP Settings ............................................................................................ 27
4 Appendix
Upgrading the Firmware ...................................................................................... 32
Automatic Update Procedure ...................................................................... 32
Manual Update Procedure .......................................................................... 38
Network Cable Diagram ...................................................................................... 42
Specications ...................................................................................................... 43
Index.................................................................................................................... 44
ixix
This page left intentionally blank.
1:2 Splitter for HDMI w/HDR
4K ULTRA
1 Getting Started
Introduction
Page Title
Front Panel
Getting Started
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
ID Name Description
1 Input This LED glows solid green when the unit
2 Outputs Each of these LED indicators will glow
3 EDID Press this button, using the end of a paper
1 4 5
Input
®
1 2
EDIDOutputs
Ultra HD 600 MHz 1:2 Splitter w/HDR
Ext Cust
Internal
2-Ch
Ch
2 3
is connected to an AC outlet and an HDMI
source is connected to the input port.
solid green when a display is powered and
connected to the associated output port.
See Output LED Status (page 9) for more
information.
clip or other sharp object, to select the
EDID mode. The LED indicators will
display the current EDID mode. See
EDID Management (page 8) for more
information.
USB
PowerMulti-
4 USB This mini-USB port is used for Syner-G™
support. See Using Syner-G™ (page 12)
for more information.
5 Power This LED indicator will glow bright blue
when the included 5V DC power supply is
connected from the splitter to an available
electrical outlet.
page | 2
Page Title
Ultra HD 600 MHz 1:2 Splitter w/HDR
EDIDOutputs
1 2
Input
®
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Internal
2-Ch
Ext Cust
USB
PowerMulti-
Ch
Introduction
Rear Panel
Getting Started
EXT-UHD600-12
ID Name Description
1 Input Connect a locking HDMI cable from an Ultra
2 Out 1, Out 2 Connect locking HDMI cables to connect up
3 5V DC Connect the included locking 5V DC power
1 2
Input Out 1 Out 2
LRP
HD source to this port.
to two Ultra HD displays to these ports.
supply to this power receptacle.
5V DC
3
page | 3
Installation
Connection Instructions
► Video
1. Use the included locking HDMI cable to connect an Ultra HD source to the Input port
Getting Started
on the rear panel of the splitter.
2. Connect locking HDMI cables (not included), to the Out 1 and Out 2 ports on the rear
panel of the splitter. The HDMI cables can then be connected in any of the following
ways:
• Connect the HDMI cables to Ultra HD displays.
• Connect the HDMI cables to additional EXT-UHD600 Splitters for cascading
purposes.
• Connect one of the HDMI cables to an Ultra HD display and the other cable to
another EXT-UHD600 Splitter.
Important
Cable quality is critical when handling 600 MHz HDMI signals. We highly
recommend Gefen Locking HDMI cables. They have been designed and
tested to work at 600 MHz and reliably transport the full 18 Gbps throughput
of HDMI 2.0.
► Power
3. Connect the included 5V DC locking power supply to the 5V DC power receptacle on
the rear panel of the splitter.
4. Connect the power supply to an available electrical outlet.
page | 4
Getting Started
Sample Application Diagram
Ultra HD
Source
Ultra HD 600 MHz
1:2 Splitter for HDMI
w/HDR
Ultra HD
Display
Installation
HDMI CABLE
Ultra HD
Display
EXT-UHD600-12
page | 5
This page left intentionally blank.
1:2 Splitter for HDMI w/HDR
4K ULTRA
2 Basic Operation
Loading...