Page 1
1:8 Distribution Amplifier
For
d
www.gefen.com
EXT-HDMI-148
USER’S MANUAL
®
Page 2
ASKING FOR ASSISTANCE
Technical Support:
Telephone (818) 772-9100
(800) 545-6900
Fax (818) 772-9120
Technical Support Hours:
8:00 AM to 5:00 PM Monday through Friday PST
Write To:
Gefen Inc.
C/O Customer Service
20600 Nordhoff St.
Chatsworth, CA 91311
support@gefen.com
www.gefen.com
Notice
Gefen Inc. reserves the right to make changes in the hard ware, packaging and any
accompanying doc u men ta tion without prior written notice.
1:8 Distribution Amplifi er For HDMI is a trademark of Gefen Inc.
All trademarks are the property of their respective owners.
© 2010 Gefen Inc., All Rights Reserved
Rev X1
Page 3
TABLE OF CONTENTS
1 Introduction / Operation Notes
2 Features
3 Panel Descriptions
4 Connecting and Operating the 1:8 HDMI Distribution Amplifi er For HDMI
5 EDID Management Feature
6 EDID Management Modes
7 Specifi cations
8 Warranty
Page 4
The Gefen 1:8 HDMI Distribution Amplifi er is the perfect solution for anyone who
needs to send one source of digital high defi nition video to multiple displays at the
same time. It supports all HDMI equipment, such as DVD players and satellite set
top boxes and all HDMI displays. In operation, the digital video source is connected
to the distribution amplifi er’s one input while eight HDMI outputs are available to be
used in part or in full. Once the unit is connected and powered, your source can be
distributed up to eight digital displays at the same time.
How It Works
Simply connect your HDMI video source to the 1:8 HDMI Distribution Amplifi er’s
input using the supplied HDMI cable. Then connect up to eight HDMI displays to
the unit’s eight HDMI outputs. Once connected and powered, your source can be
seen on all eight displays at the same time. When two or more 1:8’s are connected
together, you can create a larger distribution system.
INTRODUCTION
1
READ THESE NOTES BEFORE INSTALLING OR
OPERATING THE 1:8 DISTRIBUTION AMPLIFIER FOR HDMI
• This device supports advanced EDID management. Please see pages 5 & 6 for
complete details
• HDMI and HDCP Compliant
• Compatible with all HDMI and DVI* displays
*When used with a HDMI to DVI adapter
OPERATION NOTES
Page 5
FEATURES
Features
Connects up to eight HDMI/DVI displays at the same time to one video source
Allows simultaneous display
Supports resolutions up to 1080p, 2K, and 1920 x 1200
Extends the range of HDMI compliant devices by equalizing and re-clocking the
HDMI signal
HDMI/HDCP compliant
Includes:
(1) 1:8 Distribution Amplifi er For HDMI
(1) 6 Ft HDMI cable (M-M)
(1) 24V DC Power Supply
(1) Set of Rack Ears
(1) Users Manual
•
•
•
•
•
2
Page 6
PANEL DESCRIPTIONS
3
Front Panel
Back Panel
Power LED
Indicator
24V DC Power
Input
HDMI Output
8
HDMI Output
6
HDMI Output
4
HDMI Output
8
HDMI Input
HDMI Output
7
HDMI Output
5
HDMI Output
3
HDMI Output
1
Page 7
CONNECTING AND OPERATING
THE 1:8 DISTRIBUTION AMPLIFIER FOR HDMI
4
Connect the supplied cable from the HDTV HDMI source into the HDMI input port
of the 1:8 Distribution Amplifi er For HDMI.
Connect the user supplied cable(s) from your display(s) into the HDMI output
port(s) of the1:8 Distribution Amplifi er For HDMI.
Plug the 24V DC power supply into the 1:8 Distribution Amplifi er For HDMI.
1
2
3
How to Connect the 1:8 Distribution Amplifi er For HDMI
Page 8
5
EDID MANAGEMENT FEATURE
EDID. What is it and what is it used for?
Under normal circumstances, an source device (digital and analog) will require
information about a connected device/display to assess what resolutions
and features are available. The source can then cater its output to send
only resolutions and features that are compatible with the attached device/
display. This information is called EDID (Extended Display Information Data)
and a source device can only accept and read one EDID from a connected
device/display. Likewise, the source an only output one resolution for use by a
connected device/display.
Why is EDID so important with the 1:8 Distribution Amplifi er for HDMI?
The 1:8 Distribution Amplifi er for HDMI is complex piece of technology that
replicates a single source to multiple outputs. The single source device will
require one EDID to read. EDID management is carefully handled by 1:8
Distribution Amplifi er for HDMI to provide a single EDID for the source to read.
What options do I have to manage the EDID in the 1:8 Distribution Amplifi er
for HDMI?
First, it is important to note that each source device can only output one video/
audio signal type. This includes resolutions and timings. When multiple devices/
displays are used, such as with the 1:8 Distribution Amplifi er for HDMI, it is
important to use devices/displays that have similar or compatible resolutions/
features. This will ensure that the single video/audio signal produced by the
source device is accepted by all of the connected output devices/displays.
The user has the option, through a combination of DIP switch settings within the
1:8 Distribution Amplifi er for HDMI, to choose how the unit will manage the EDID
from multiple HDMI devices/displays. Therefore the user has some control over
the resolutions/features that the source device will output. The 1:8 Distribution
Amplifi er for HDMI has a multiple EDID management modes that will control how
the EDID information from multiple devices/displays are combined, ignored, and
routed.
How do I change EDID modes in the 1:8 Distribution Amplifi er for HDMI?
There is an bank of 8 DIP switches located on the main-board inside of the 1:8
Distribution Amplifi er for HDMI. DIP switches 1, 2, 5, and 7 are used in different
combinations to manage the EDID modes.
To access these DIP switches it will be required to open the unit. To do this,
remove all screws on the underside and side of the unit. Remove all HEX screws
on the rear panel. This includes the screws above each HDMI port. Carefully
slide the unit apart and locate the DIP switch bank on the main-board.
Page 9
6
EDID MANAGEMENT MODES
EDID Modes
The diagram below illustrates the 8 DIP switch bank.
DIP SWITCH Function
1 EDID Mode
2 EDID Mode
3 N/A
4 N/A
5 EDID Mode
6 N/A
7 EDID Mode
8 N/A
Use DIP switches 1, 2, 5, and 7 to select the desired EDID management mode.
EDID Mode 0 (Switch 1=OFF Switch2=OFF Switch5=ON)
• Edid is copied from the device connected to the fi rst active hdmi output
port.
• All features newer that HDMI 1.2 are cleared.
EDID Mode 1 (Switch 1=ON Switch2=OFF Switch5=ON)
• Same as Mode 0 and adds basic audio support.
EDID Mode 2 (Switch 1=OFF Switch2=ON Switch5=ON)
• Same as Mode 0 and adds full audio support.
EDID Mode 3 (Switch 1=ON Switch2=ON Switch5=OFF)
• EDID is generated based on the common video and audio features of all
of the connected output devices.
EDID Mode 4 (Switch 1=OFF Switch2=ON Switch5=OFF)
• Same as Mode 3 and adds basic audio support.
EDID Mode 5 (Switch 1=ON Switch2=OFF Switch5=OFF)
• Same as Mode 3 and adds full audio support.
EDID Mode 6 (Switch 1=OFF Switch2=OFF Switch5=OFF) DEFAULT
• EDID is generated based on the common video features of all of
the connected devices and the combined audio features of all of the
connected output devices.
EDID Mode 7 (Switch 1=ON Switch2=ON Switch5=ON)
• EDID is passed unmodifi ed from the device connected to the fi rst
active output port.
1
2
3
4
5
6
7
8
v. 2015
Page 10
7
SPECIFICATIONS
Video Amplifi er Bandwidth ............................................................................ 165 MHz
Input Video Signal ................................................................................... 1.2 Volts p-p
Input DDC Signal .............................................................................. 5 Volts p-p (TTL)
Single Link Range ................................................................... ...1080p / 1920 x 1200
Input Connector Type .................................................................. HDMI Type A 19 Pin
Output Connector Type ................................................................HDMI Type A 19 Pin
Power Consumption .......................................................................... 60 Watts (max.)
Power Supply ................................................................................................. 24V DC
Dimensions .............................................................................. 17”W x 1.75”H x 5.5”D
Shipping Weight ................................................................................................. 6 Lbs
Page 11
8
WARRANTY
Gef
en warrants the equipment it manufactures to be free from defects in material
and workmanship.
I
f
equipment fails because of such defects and Gefen is notifi ed within two (2)
y
ears from the date of shipment, Gefen will, at its option, repair or replace the
e
quipment, provided that the equipment has not been subjected to mechanical,
e
lectrical, or other abuse or modifi cations. Equipment that fails under conditions
other than those covered will be repaired at the current price of parts and labor in
eff
ect at the time of repair. Such repairs are warranted for ninety (90) days from
the day of reshipment to the Buyer.
This warranty is in lieu of all other warranties expressed or implied, including
without limitation, any implied warranty or merchantability or fi tness for any
articular purpose, all of which are expressly disclaimed.
1. Proof of sale may be required in order to claim warranty.
2.
ustomers outside the US are responsible for shipping charges to and from
efen.
.
opper cables are limited to a 30 day warranty and cables must be in their
original condition.
The information in this manual has been carefully checked and is believed to
be accurate. However, Gefen assumes no responsibility for any inaccuracies
that may be contained in this manual. In no event will Gefen be liable for
direct, indirect, special, incidental, or consequential damages resulting from
any defect or omission in this manual, even if advised of the possibility of such
damages. The technical information contained herein regarding the features and
pecifi cations is subject to change without notice.
For the latest warranty coverage information, please visit Gefen’s Warranty web
age at http://www.gefen.com/kvm/aboutus/warranty.js
p
RODUCT REGISTRATIO
N
lease register your product online by visiting Gefen’s web site at
http://www.gefen.com/kvm/Registry/Registration.jsp
Page 12
Page 13
Rev X1
20600 Nordhoff St., Chatsworth CA 91311
1-800-545-6900 818-772-9100 fax: 818-772-9120
www.gefentv.com support@gefen.com
Loading...