w
EXT-HDMI1.3-1F
O
an
Us
M
l
ww.gefen.co
ASKING FOR ASSISTANC
E
T
t
0
0
0
T
:
e
:
C
e
0600
1
e
g
e
are
cou
f Gef
C
©
y of
6
echnical Suppor
Telephone (818) 772-910
(800) 545-690
Fax (818) 772-912
echnical Support Hours
:00 AM to 5:00 PM Monday through Friday, Pacifi c Tim
Write To
efen, LL
o Customer Servic
2
Nordhoff St
hatsworth, CA 9131
www.gefen.com
upport@gefen.com
Notic
efen, LLC reserves the right to make changes in the hard ware, packaging and
any accompanying doc u men ta tion without prior written notice.
HDMI, the HDMI Lo
trademarks or registered trademarks of HDMI Licensing in the United States and
xtender for HDMI 1.3 Over One Fiber with IR is a trademark o
All trademarks are the propert
o, and High-Defi nition Multimedia Interfac
ther
2011 Gefen, LLC. All rights reserved.
ntries.
their respective owners.
en, LL
Rev A
CONTENT
S
oduction
t
t
n
e
y
1 Intr
2 Operation Notes
Features
4 Sender Unit Layou
Sender Unit Descriptions
Receiver Unit Layou
7 Receiver Unit Descriptions
Connecting and Operating the Extender
Wiring Diagram
DIP Switch Confi guratio
10 DIP Switches
11 Local EDID / External (Pass-Through) EDID Modes
11 Deep Color
11 Calibration Procedur
12 Specifi cations
13 Warrant
INTRODUCTIO
N
T
ongratulations on your purchase of the Extender for HDMI 1.3 Over One Fiber
with IR. Your complete satisfaction is very important to us.
efen
efen delivers innovative, progressive computer and electronics add-on solutions
that harness integration, extension, distribution and conversion technologies.
efen’s reliable, plug-and-play products supplement cross-platform computer
stems, professional audio/video environments and HDTV systems of all sizes
with hard-working solutions that are easy to implement and simple to operate.
he Gefen Extender for HDMI 1.3 Over One Fiber with IR
The Gefen Extender for HDMI 1.3 Over One Fiber with IR transmits 1080p Full
D in Deep Color and multi-channel digital audio up to 1000 feet (330 meters)
over a single-strand SC fi ber optic cable. Extraordinary distances can be
achieved using this feature-rich device.
1080p Full HD with Deep Color is instantaneously displayed at the remote
ocation. This product also eliminates EMI (electromagnetic interference), picture
ut-outs and screen distortions traditionally seen with copper-based HDMI
xtenders.
A multi-channel digital audio experience is delivered with Dolby TrueHD® and
DTS-HD® Master Audio™.
A single-strand SC fi ber cable carries the IR back channel and bidirectional
-232, facilitating convenient local control of the video source devices.
How It Works
onnect the Sender Unit to the high defi nition source using the provided HDMI
able. Connect the Receiver Unit to an HDTV display using another HDMI cable.
un a single strand of SC fi ber optic cable from Sender Unit to the Receiver Unit.
Power up both the Sender Unit and the Receiver Unit. A clean and vibrant HDMI
A/V signal will appear on the display along with clear and crisp digital audio.
end IR commands from the IR Remote Control back to A/V source equipment
via the IR back channel using the fi ber optic cable connecting the Sender Unit
to the Receiver Unit. The Sender Unit has an IR blaster port, enabling wide IR
ignal coverage in an A/V equipment room.
In addition, RS-232 commands from a home automation system or PC can be
sed to control the source device or any other RS-232 device using the ports on
the Sender Unit and the Receiver Unit.
OPERATION NOTE
S
f
f
g
:
(
E
fo
ging fi
READ THESE NOTES BEFORE INSTALLING OR
OPERATING THE EXTENDER FOR HDMI 1.3 OVER ONE FIBER WITH IR
• IR data repeater
transmitted
be transmitted from the Sending unit to the Receiving unit.
•
se one SC-terminated multi-mode fi ber optic cable to operate the HDMI 1.3
ver One Fiber with IR.
• 1080p video may be extended up to 1000 feet (300m), depending on the
type of fi ber optic cable used. The following maximum extension distances
will be possible dependin
• 100m (330 ft) on 62.5/125 μm (OM1) multi-mode SC fi ber
• 300m
•
-232 data is bi-directional for direct commands and echo function or
tatus information.
These steps must be followed when setting up the
over one Fiber with IR
•
onnect the SC fi ber optic cable between the Sender unit and the Receiver
nit.
unctionality is single-directional. IR data can only be
rom the Receiving unit back to the Sending unit. IR data cannot
on the types of fi ber optic cabling that are used
1000 ft) on 50/125 μm (OM3) multi-mode SC fi ber
IMPORTANT CALIBRATION PROCEDUR
efen Extender for HDMI 1.3
r the fi rst time.
•
et DIP switch 3 on both the Sender unit and the Receiver unit to the OFF
osition.
• Apply power to the source and to both the Sender and Receiver units. The
LED indicators on both the Sender unit and Receiver unit will alternate from
ed to green during the calibration process. The calibration process can take
p to 120 seconds to complete.
•After the calibration process has fi nished, the LED indicators on both the
ender unit and the Receiver unit will be solid green. Set DIP switch 3 to
the ON position on both the Sender unit and the Receiver unit to lock the
alibration settings.
NOTE: When chan
epeated. See page 11 for details on the calibration procedure.
ber optic cables, the calibration procedure must be
FEATURE
S
)
y
o
gh
K
gh
d
)
e
)
t
t
t
)
)
HDMI 1.3 Features
• 225 MHz (up to 12 bit YUV 444 @ 1080p
• Deep Color
• Dolb
• Lip-Sync
•
Features
•
• 3DTV Pass-Throu
• Delivers highest quality signal of any HDMI extension metho
• EDID Detection/Adjustment for rapid integration of source and displays
• Extends HDMI and RS-232 up to 1000 feet (300m
•
• Immune to electromagnetic interference (EMI
•
TrueHD and DTS-HD Master Audi
EC Protocol Pass-Throu
upports video resolutions up to 1080p,1920 x 1200 and 2
ses widely available single-strand multi-mode SC fi ber optic cabl
DCP Complian
ackage Includes
1) Extender for HDMI 1.3 Over One Fiber with IR - Sender uni
1) Extender for HDMI 1.3 Over One Fiber with IR - Receiver uni
2) Mounting Plates
1) 6 ft HDMI Cable (M-M
1) 6 ft DB9 Serial Cable (M-F
2) 5V DC Locking Power Supplies
1) User Manual
4
SENDER UNIT LAYOU
T
t
4
Fron
Back
5
7
SENDER UNIT DESCRIPTION
S
r
y
S
r
t
4
t
t
r
ower Indicato
This two-color LED will turn bright red once the included 5V DC locking power
upply has been properly connected to the unit and the locking power suppl
as been connected to an available wall outlet. This LED will turn bright green
once the
alibration Indicato
This LED will alternate from red to green during the calibration procedure. The
LED will turn solid green once the calibration procedure has been completed.
R Blaster Por
onnect an IR Blaster cable (Gefen part # EXT-2IREMIT) to this port.
ocking HDMI Input Por
onnect a Hi-Def source to this HDMI port.
S-232 Input Por
onnect the controlling device to this port.
Fiber Optic Connector (SC-Type)
This connector accepts 1 strand of SC-terminated fi ber optic cable that will link
the Sender Unit and Receiver Unit together. The
ver One Fiber with IR will only accept multi-mode fi ber optic cabling.
5V DC Locking Power Connecto
onnect the included 5V DC Locking Power Supply to this receptacle.
ender unit and Receiver unit are communicating correctly.
efen Extender for HDMI 1.3
5
RECEIVER UNIT LAYOU
T
2
Front
Back
7
5
RECEIVER UNIT DESCRIPTION
S
t
t
t
w
4
r
r
y
r
t
S-232 Output Por
onnect a controlling device to this port.
ocking HDMI Output Por
onnect a HDTV display to this HDMI por
R Windo
eceives signals from the Hi-Def source IR remote control unit. The IR signals
are sent back to the source device, when using an IR Blaster.
alibration Indicato
This LED will alternate from red to green during the calibration procedure. The
LED will turn solid green once the calibration procedure has been completed.
ower Indicato
This two-color LED will turn bright red once the included 5V DC locking power
upply has been properly connected to the unit and the locking power suppl
as been connected to an available wall outlet. This LED will turn bright green
once the Sender unit and Receiver unit are communicating correctly.
5V DC Locking Power Connecto
onnect the included 5V DC Locking Power Supply to this receptacle.
R Extender Por
onnect an IR Extender cable (Gefen part # EXT-RMT-EXTIR) to this port.
Fiber Optic Connector (SC-Type)
This connector accepts 1 strand of SC-terminated fi ber optic cable that will link
the Sender Unit and Receiver Unit together. The
ver One Fiber with IR will only accept multi-mode fi ber optic cabling.
efen Extender for HDMI 1.3
7
cable
T
y
CONNECTING AND OPERATING TH
E
GEFEN EXTENDER FOR HDMI 1.3 OVER ONE FIBER WITH IR
How to Connect the Extender for HDMI 1.3 over One Fiber with IR
onnect a Hi-Def source to the Sender Unit using the included Locking HDMI
1.
le.
onnect the HDTV display to the Receiver Unit with a user-supplied
DMI
2.
onnect an SC-terminated fi ber optic cable to the Sender Unit. Connect the
opposite end of the fi ber cable to the Receiver Unit.
.
PTIONAL: Connect an RS-232 cable from the RS-232 serial port on the
ontrolling device to the RS-232 port on the Sender Unit. Connect another
-232 serial cable from the RS-232 port on the Receiver Unit to the RS-
232 port of the RS-232 device.
4.
PORTAN
the Receiver Unit, see page 11 for information on calibrating the Sender Unit
and Receiver Unit.
After the Sender Unit and Receiver Unit have been properly calibrated, a vibrant
DTV HD picture will be seen, along with multichannel digital audio (if the displa
upports audio).
.
: Before connecting the power supplies to the Sender Unit and
Wiring Diagram for the Extender for HDMI 1.3 over One Fiber with IR
SC-SC FIBER OPTIC CABLE
(Up to 1,000 ft)
HDMI CABLE
RS-232
IR
IR Emitter
Hi-Def Source
Receiver
Sender
RS-232 Controller
IR Extender
HD Display
with RS-232 Control
EXT-HDMI1.3-1FO
IP SWITCH CONFIGURATIO
N
h
on
)
)
)
OT US
h
on
)
OT US
IP Switches
n the bottom of the Sender Unit and Receiver Unit are a bank of four (4) DIP
witches. These DIP switches provide control over EDID, Deep Color, and unit
alibration.
emove the strip of tape to expose the DIP switches. To change the DIP switch
ettings, move the appropriate DIP switch to its ON or OFF position using a small
ointed object. The DIP switches and their functions are shown below.
DIP Switc
4N
DIP Switc
4N
Functi
EDID Mode: Local (OFF) or External (ON
Deep Color Mode: 12-bit (OFF) or 8-bit (ON
Functi
NOT USED
NOT USED
Sender Unit DIP switches
alibration Mode: On (OFF) or Lock (ON
ED
Receiver Unit DIP switches
alibration Mode: On (OFF) or Lock (ON
ED
N
IP 1 - EDID Mod
e
y
g
y
y f
-
)
e
for details
•
FF - Local EDID
IP SWITCH CONFIGURATIO
When Local EDID mode is used, the EDID will be assembled b
all video and audio features of the connected device. Deep Color support
will be manually controlled: If Deep Color is supported by the display(s),
DIP 2 should be set to the ON position (see DIP 2 - Deep Color, below). B
default, the unit is shipped with DIP 1 in the OFF position.
•
N - Pass-Through EDID
Allows all video and audio features of the connected devices to be passed to
the source device without control over Deep Color.
IP 2* - Deep Color
NOTE: DIP switch 2 is onl
ion.
FF - Enables Deep Color support (12-bit color
•
Enables Deep Color support. In Pass-through EDID Mode, setting DIP2 =
FF has no effect since all EDID information is passed through.
•
N - Forces 8-bit Color
Disables Deep Color in the EDID. Deep Color management is only available
when Local EDID is being used.
unctional when DIP switch 1 is set to the OFF posi
copyin
IP 3 - Calibration Mod
•
FF - Enables Calibration Mode
Enables Calibration Mode. Make sure to set DIP switch 3 on both the
ender Unit and Receiver Unit when calibrating the Extenders. See page 11
.
•
N - Calibration Mode Lock
Locks the calibration settings. Set DIP switch 3 on both the Sender Unit and
eceiver Unit to the ON position after the calibration process has completed.
ee page 11 for details on the calibration process.
10
1
IP SWITCH CONFIGURATIO
N
t
T
ON
E
T
e
e
Calibrating the Sender Unit and Receiver Uni
IMPORTAN
ender Unit and Receiver are not powered.
1.
the OFF position (see page 9).
2.
.
the OFF position (see page 9).
4.
The LED indicators on both the Sender Unit and Receiver Unit will alternate from
ed to green during the calibration process. The calibration process can take up
to 120 seconds to complete.
After the calibration process has fi nished, the LED indicators on both the Sender
nit and the Receiver unit will turn solid green. Set DIP switch 3 to the
osition on both the Sender Unit and the Receiver Unit to lock the calibration
ettings.
NOT
: Before beginning the calibration process, make sure that the
ake sure DIP switch 3 on both the Sender Unit and the Receiver Unit are in
onnect one end of the fi ber cable to the Sender Unit. Connect the other
nd of the fi ber cable to the Receiver Unit.
ake sure DIP switch 3 on both the Sender Unit and the Receiver Unit are in
onnect the 5V DC Locking Power Supplies to the Sender Unit and the
eceiver Unit. Do not overtighten the locking connectors. Plug the power
rd into an available electrical outlet.
: If the fi ber optic cable is changed, repeat the calibration procedure.
roubleshooting Procedur
• If the Sender Unit and Receiver Unit did not complete the calibration
rocess, the indicator LEDs on both Sender Unit and Receiver Unit will be
ed. Check the fi ber connections carefully and cycle the power on both the
ender Unit and the Receiver Unit and repeat the calibration procedure.
• When the indicator LED at one unit is GREEN and the other is RED,
cle power on the unit with the RED indicator. It is also recommended to
cle power on both the Sender Unit and the Receiver Unit to perform a full
libration.
• If the calibration procedure continues to fail, contact Gefen Technical
upport under the Asking For Assistanc
nual.
section at the beginning of this
1
SPECIFICATION
S
K
p
)
n
9
)
)
)
z
o
e
C
)
Video Amplifi er Bandwidth ........................................................................ 225 MHz
aximum Resolutions Supported: ..................................1080p60, 1920x1200, 2
Input Video Signal .............................................................................. 1.2 Volts p-
Input DDC Signal .......................................................................... 5 Volts p-p (TTL
DMI Input/Output Connector ......................................................... Type A, 19-pi
-232 Input/Output Connector........................................................................DB
-232 Data Transmission Rate ............................................115,200 kbps (max.
LED Indicator (Power ON/OFF) ......................................2-color LED (red / green
LED Indicator (Fiber Calibration) .....................................2-color LED (red / green
IR Modulation Frequency: ...........................................................................38 KH
IR Blaster: .................................................................................3.5mm Mini-Stere
Link Connector ................................................................ SC Fiber Optic x 1 cabl
Power Supply ............................................................................................... 5V D
Power Consumption .................................................................. 10W per unit (max
Dimensions .......................................................................... 4.2”W x 1.2”H x 3.8”D
hipping Weight ............................................................................................. 5 lbs.
ompliancy: RoHS and CE Certifi ed; Complies with US/EU Standards
HDMI 1.3, HDMI 1.2, HDCP 1.1 and DVI 1.0 Compliant.
UL-Certifi ed Power Supply.
12
3
efen warrants the equipment it manufactures to be free from defects in material
f
y
N
.
and workmanship.
I
equipment fails because of such defects and Gefen is notifi ed within two (2)
ears from the date of shipment, Gefen will, at its option, repair or replace the
quipment, provided that the equipment has not been subjected to mechanical,
lectrical, or other abuse or modifi cations. Equipment that fails under conditions
other than those covered will be repaired at the current price of parts and labor in
ect at the time of repair. Such repairs are warranted for ninety (90) days from
the day of reshipment to the Buyer.
This warranty is in lieu of all other warranties expressed or implied, including
without limitation, any implied warranty or merchantability or fi tness for any
articular purpose, all of which are expressly disclaimed.
1. Proof of sale may be required in order to claim warranty.
2.
ustomers outside the US are responsible for shipping charges to and from
efen.
.
opper cables are limited to a 30 day warranty and cables must be in their
original condition.
The information in this manual has been carefully checked and is believed to
be accurate. However, Gefen assumes no responsibility for any inaccuracies
that may be contained in this manual. In no event will Gefen be liable for
direct, indirect, special, incidental, or consequential damages resulting from
any defect or omission in this manual, even if advised of the possibility of such
damages. The technical information contained herein regarding the features and
pecifi cations is subject to change without notice.
For the latest warranty coverage information, refer to the Warranty and Return
Policy under the Support section of the Gefen Web site at www.gefen.com.
RODUCT REGISTRATIO
lease register your product online by visiting the Register Product page
nder the Support section of the Gefen Web site
1
1
800
6900
20
m
Rev A
6
1-
This product uses UL listed power supplies.
-545-
Nordhoff St., Chatsworth CA 9131
818-772-9100 fax: 818-772-91
www.gefen.com support@gefen.co
Pb
Loading...