1:5 Splitter For
HDMI 1.3
Model #EXT-HDMI1.3-145
USER MANUAL
www.gefen.com
ASKING FOR ASSISTANCE
Technical Support:
Telephone (818) 772-9100
(800) 545-6900
Fax (818) 772-9120
Technical Support Hours:
8:00 AM to 5:00 PM Monday through Friday.
Write To:
Gefen Inc.
c/o Customer Service
20600 Nordhoff Street
Chatsworth, CA 91311
www.gefen.com
support@gefen.com
Notice
Gefen Inc. reserves the right to make changes in the hard ware, packaging
and any accompanying doc u men ta tion without prior written notice.
1:5 Splitter For HDMI 1.3 is a trademark of Gefen Inc.
HDMI is a trademark of hdmi.org
© 2008 Gefen Inc., All Rights Reserved
TABLE OF CONTENTS
Introduction1.
Features2.
Panel Descriptions3.
Connecting and Operating the 1:5 Splitter for HDMI 1.34.
Specifi cations5.
Warranty6.
INTRODUCTION
The Gefen 1:5 Splitter for HDMI 1.3 allows set-top boxes, DVD players, Bluray players and other HDTV devices with HDMI outputs to be connected to
up to fi ve HDTV displays (or more if multiple splitters are utilized in place of
HDTV displays
How It Works
The 1:5 Splitter for HDMI 1.3 is a distribution hub that sends the same HDMI
signals to up to fi ve HDTV digital displays. You simply connect your HDMI
video source to the 1:5 HDMI 1.3 Splitters HDMI input jack, then connect
your HDMI-compatible displays to each of the HDMI outputs. Power-cycle
all equipment and you should see beautiful, sharp HDMI video on all of your
HDMI displays.
OPERATION NOTES
READ THESE NOTES BEFORE INSTALLING OR
OPERATING THE 1:5 SPLITTER FOR HDMI 1.3
Display information from the display connected to HDMI output port 1 is sent •
back to the source. Therefore, all other displays connected to the 1:5 Splitter
for HDMI 1.3 must be capable of accepting the timings and resolutions of the
display that is connected to HDMI output port 1. It is recommended that the
display with the lowest native resolution be connected to HDMI output port 1.
This is to ensure that a compatible video signal will be able to be displayed
on all connected monitors.
HDMI/HDCP compliant•
Compatible with all HDMI and DVI* displays•
*When used with a HDMI to DVI adapter
1
Features
Lip-Sync Pass Through •
225 MHz (up to 12 bit YUV 444 supported @ 1080p) •
Deep Color Supported (XV Color Supported) •
Color Space Conversion Supported •
Dolby Tru-HD & DTS Master Supported •
CEC Pass Through •
Includes:
(1) 1:5 Splitter for HDMI 1.3
(1) 6 ft HDMI cable (m-m)
(1) 24V DC Power Supply
(1) Set of Rack Ears
(1) User’s Manual
FEATURES
2
PANEL DESCRIPTIONS
&
Power LED
Reset
Act. LED
supply
Connects to
24VDC power
1-10
HDMI Output
Input
HDMI
EDID
Switch
3
CONNECTING AND OPERATING THE 1:5 SPLITTER FOR HDMI 1.3
How to Connect the 1:5 Splitter for HDMI 1.3 to your devices
Connect the supplied cable from the HDTV HDMI source into the 1:5 1.
Splitter for HDMI 1.3 input.
Connect the cables from your displays (monitor or projector) into the 2.
HDMI outs of the 1:5 Splitter for HDMI 1.3.
Plug the 24VDC power supply into the 1:5 Splitter for HDMI 1.3.3.
NOTE:
sent back to the source. Therefore, all other displays connected to the 1:5 Splitter
for HDMI 1.3 must be capable of accepting the timings and resolutions of the display
that is connected to HDMI output port 1. It is recommended that the display with the
lowest native resolution be connected to HDMI output port 1. This is to ensure that a
compatible video signal will be able to be displayed on all connected monitors. There is
a generic 1080i EDID programmed into the 1:5 Splitter for HDMI 1.3 that can be used
instread. Please see below for the activation process.
Display information from the display connected to HDMI output port 1 is
EDID SWITCH
The HDMI 1:5 has an EDID Switch which will determine if you are going to
use the EDID from the display attached to output 1 or use an onboard EDID.
If you want to use the EDID from the display attached to output 1, make
sure the switch is selected to "EXT".
If you want to use the onboard EDID, make sure the switch is selected to
"INT" which will give you a generic EDID of 1080i.
4
SPECIFICATIONS
Video Amplifi er Bandwidth.................................................................225 MHz
Input Video Signal........................................................................1.2 volts p-p
Input DDC Signal...................................................................5 volts p-p (TTL)
Single Link Range.............................................................1080p/1920 x 1200
HDMI Connector..............................................................type A 19 pin female
Power Supply .......................................................................................24V DC
Power Consumption.................................................................60 watts (max)
Dimensions...................................................................17”W x 1.75”H x 5.5”D
Rackmountable.........................................................................1U rack space
Shipping Weight......................................................................................5 lbs.
5
Loading...