®
1:2 Splitter For
HDMI 1.3
EXT-HDMI1.3-142
User’s Manual
www.gefen.com
ASKING FOR ASSISTANCE
Technical Support:
Telephone (818) 772-9100
(800) 545-6900
Fax (818) 772-9120
Technical Support Hours:
8:00 AM to 5:00 PM Monday thru Friday PST
Write To:
Gefen LLC
c/o Customer Service
20600 Nordhoff St
Chatsworth, CA 91311
www.gefen.com
support@gefen.com
Notice
Gefen LLC reserves the right to make changes in the hard ware, packaging and
any accompanying doc u men ta tion without prior written notice.
1:2 Splitter For HDMI 1.3 is a trademark of Gefen LLC
© 2010 Gefen LLC, All Rights Reserved
All trademarks are the property of their respective owners.
Rev A1
CONTENTS
1 Introduction
2 Operation Notes
3 Features
4 Panel Descriptions
6 Connecting And Operating The 1:2 Splitter For HDMI
7 Specifi cations
8 Warranty
INTRODUCTION
Congratulations on your purchase of the 1:2 Splitter For HDMI. Your complete
satisfaction is very important to us.
Gefen
Gefen delivers innovative, progressive computer and electronics add-on solutions
that harness integration, extension, distribution and conversion technologies.
Gefen’s reliable, plug-and-play products supplement cross-platform computer
systems, professional audio/video environments and HDTV systems of all sizes
with hard-working solutions that are easy to implement and simple to operate.
The Gefen 1:2 Splitter For HDMI
The Gefen 1:2 Splitter for HDMI 1.3 allows set-top boxes, DVD players, Blu-ray
players and other HDTV devices with HDMI outputs to be connected to up to
two HDTV displays (or more if multiple splitters are utilized in place of HDTV
displays).
How It Works
The 1:2 HDMI 1.3 Splitter is a distribution hub that sends the same HDMI signals
to up to two HDTV digital displays. You simply connect your HDMI video source
to the 1:2 HDMI 1.3 Splitters HDMI input jack, then connect your HDMI-compatible displays to each of the HDMI outputs. Power-cycle all equipment and you
should see beautiful, sharp HDMI video on all of your HDMI displays.
1
OPERATION NOTES
READ THESE NOTES BEFORE INSTALLING OR
OPERATING THE 1:2 SPLITTER FOR HDMI 1.3
• By default, display information from the display connected to HDMI output
port 1 is sent back to the source. Therefore, the other display connected
to the 1:2 Splitter for HDMI 1.3 must be capable of accepting the timings
and resolutions of the display that is connected to HDMI output port 1.
It is recommended that the display with the lowest native resolution be
connected to HDMI output port 1. This is to ensure that a compatible video
signal will be able to be displayed on all connected monitors. There is a
generic EDID programmed into the 1:2 Splitter for HDMI 1.3 that can be
used instead. Please see page 6 for more details.
• HDMI/HDCP compliant
• Compatible with all HDMI and DVI displays*
*When used with a HDMI to DVI adapter
Connection Diagram for the 1:2 Splitter for HDMI 1.3
EXT-HDMI1.3-142D
2
FEATURES
Features
• Connects up to two HDMI / DVI displays from one HDMI source
• Optionally add more displays by connecting splitters
• Easily attains resolutions up to 1080p, 2k, and 1920 x 1200
• HDMI and HDCP compliant
HDMI 1.3 Features
• Lip-Sync Pass Through
• 225 MHz (up to 12 bit YUV 444 supported @ 1080p)
• Deep Color Supported (XV Color Supported)
• Color Space Conversion Supported
• Dolby Tru-HD & DTS Master Supported
• CEC Pass Through
Includes:
(1) 1:2 Splitter for HDMI 1.3
(1) 6 ft HDMI cable (m-m)
(1) 5V DC Power Supply
(1) User’s Manual
3
PANEL DESCRIPTIONS
Front Panel
1
526
1 Power LED
This LED will activate once a valid power source is applied.
2 Internal EDID LED
This LED will activate only when the pre-programmed internal EDID is being
used. Please see page 6 for more details on the internal EDID.
3 External EDID LED (default EDID routing)
This LED will activate only when the external EDID is being used. Please
see page 6 for more details on the external EDID.
4 Link LED
This LED will activate when a valid link between the source and the splitter is
detected.
7
3
Back Panel
4
8910
5 EDID Button
This button will activate the onboard EDID. Press this button (the Int. EDID
should turn on and the Ext. LED should turn off) and reset the unit using the
Reset button (below) to initialize this EDID mode. To use an external EDID,
press the EDID button again (the Int. LED should turn off and the Ext. LED
should turn on) and press the Reset button to initialize this EDID mode.
6 Reset Button
This button will reset the unit and initialize whichever EDID mode is currently
selected.
4
PANEL DESCRIPTIONS
7 HDMI Input
This is the input for the HDMI source device. When a valid source is
detected by the splitter, the Link LED will activate.
8 HDMI Out 1
This is the fi rst HDMI output port. Connect a valid HDMI display to this port.
When the External EDID mode is active, the EDID form the display
connected to this port will be used to send to the source.
9 HDMI Out 2
This is the second HDMI output port. Connect a valid HDMI display to this
port.
10 5V DC Power Input
This port is for the included 5V DC power supply. When a valid 5V power
supply is attached, the Power LED will activate.
5
CONNECTING AND OPERATING THE 1:2 SPLITTER FOR HDMI
How to Connect the 1:2 Splitter For HDMI 1.3
1. Connect the supplied cable from the HDMI source into the 1:2 Splitter for
HDMI 1.3 input.
2. Connect the cables from your displays (monitor or projector) into
the HDMI outs of the 1:2 Splitter for HDMI 1.3. Up to 2 displays are
supported.
3. Plug the 5V DC power supply into the 1:2 Splitter for HDMI 1.3.
NOTE:
port 1 is sent back to the source. Therefore, the other display that is connected to the
1:2 Splitter for HDMI 1.3 must be capable of accepting the timings and resolutions of the
display that is connected to HDMI output port 1. It is recommended that the display with
the lowest native resolution be connected to HDMI output port 1. This is to ensure that a
compatible video signal will be able to be displayed on all connected monitors. There is
a generic EDID programmed into the 1:2 Splitter for HDMI 1.3 that can be used instead.
Please see below for the activation process.
By Default, the display information from the display connected to HDMI output
EDID MODE
The HDMI 1:2 has an EDID button which will determine if the EDID is used
from the display attached to output 1 (Ext. mode) or if the onboard EDID
(Int. mode) will be used.
The current EDID mode can be determined by which EDID mode LED is
active on the front panel. The Ext LED will indicate that the external EDID
(from output port 1) is being used, and the Int LED will indicate that the
internal pre-programmed EDID is being used.
If you want to use the onboard EDID, press the EDID button on the rear
panel and then press the reset button to activate the new EDID mode. To
revert back to using the external EDID, press the EDID button again and
then reset the unit using the reset button to activate the new EDID mode.
Listed Resolutions in the Internal EDID:
1280x720p 50 Hz (Naitive)
1280x720p 59.94 / 60 Hz (Naitive)
1920 x 1080i 50 Hz
1920 x 1080i 59.94 / 60 Hz
720 x 480p 59.94 / 60 Hz
720 x 576p 50 Hz
1920 x 1080p 50 Hz
1920 x 1080p 59.94 / 60 Hz
1440 x 480p 59.94 / 60 Hz
1440 x 576p 50 Hz
6
SPECIFICATIONS
Video Amplifi er Bandwidth ............................................................... 225 MHz
Input Video Signal ...................................................................... 1.2 Volts p-p
Input DDC Signal ................................................................ 5 Volts p-p (TTL)
Single Link Range ........................................................... 1080p/1920 x 1200
HDMI Connector ......................................................... Type A 19 Pin Female
Power Supply ...................................................................................... 5V DC
Power Consumption .............................................................. 13 Watts (max)
Dimensions .................................................................... 9.4”W x 1”H x 4.6”D
Shipping Weight .................................................................................... 3 lbs.
7
WARRANTY
Gef
f
y
e
e
eff
p
Gef
3
s
pag
p
N
en warrants the equipment it manufactures to be free from defects in material
and workmanship.
I
equipment fails because of such defects and Gefen is notifi ed within two (2)
ears from the date of shipment, Gefen will, at its option, repair or replace the
quipment, provided that the equipment has not been subjected to mechanical,
lectrical, or other abuse or modifi cations. Equipment that fails under conditions
other than those covered will be repaired at the current price of parts and labor in
ect at the time of repair. Such repairs are warranted for ninety (90) days from
the day of reshipment to the Buyer.
This warranty is in lieu of all other warranties expressed or implied, including
without limitation, any implied warranty or merchantability or fi tness for any
articular purpose, all of which are expressly disclaimed.
1. Proof of sale may be required in order to claim warranty.
2.Customers outside the US are responsible for shipping charges to and from
en.
.Copper cables are limited to a 30 day warranty and cables must be in their
original condition.
The information in this manual has been carefully checked and is believed to
be accurate. However, Gefen assumes no responsibility for any inaccuracies
that may be contained in this manual. In no event will Gefen be liable for
direct, indirect, special, incidental, or consequential damages resulting from
any defect or omission in this manual, even if advised of the possibility of such
damages. The technical information contained herein regarding the features and
pecifi cations is subject to change without notice.
For the latest warranty coverage information, please visit Gefen’s Warranty web
e at http://www.gefen.com/kvm/aboutus/warranty.js
RODUCT REGISTRATIO
lease register your product online by visiting Gefen’s web site at
http://www.gefen.com/kvm/Registry/Registration.jsp
8
*ma-HDMI1.3-142*
Rev A1
20600 Nordhoff St., Chatsworth CA 91311
1-800-545-6900 818-772-9100 fax: 818-772-9120
www.gefen.com support@gefen.com
Pb
Loading...