Page 1
DVI ELR Lite
3GSDI
EXT-DVI-1CAT5-SR
User Manual
Release A2
Audio
Embedder
Extender over
one CAT-5
Page 2
DVI ELR Lite Extender over one CAT-5
Important Safety Instructions
GENERAL SAFETY INFORMATION
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this product near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install or place this product near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong are provided for
your safety. If the provided plug does not t into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specied by the manufacturer.
12. To reduce the risk of electric shock and/or damage to this product, never handle or
touch this unit or power cord if your hands are wet or damp. Do not expose this
product to rain or moisture.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualied service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally,
or has been dropped.
15. Batteries that may be included with this product and/or accessories should never be
exposed to open ame or excessive heat. Always dispose of used batteries
according to the instructions.
ii
Page 3
DVI ELR Lite Extender over one CAT-5
Warranty Information
Gefen warrants the equipment it manufactures to be free from defects in material and
workmanship.
If equipment fails because of such defects and Gefen is notied within two (2) years from
the date of shipment, Gefen will, at its option, repair or replace the equipment, provided
that the equipment has not been subjected to mechanical, electrical, or other abuse or
modications. Equipment that fails under conditions other than those covered will be
repaired at the current price of parts and labor in effect at the time of repair. Such repairs
are warranted for ninety (90) days from the day of reshipment to the Buyer.
This warranty is in lieu of all other warranties expressed or implied, including without
limitation, any implied warranty or merchantability or tness for any particular purpose, all of
which are expressly disclaimed.
1. Proof of sale may be required in order to claim warranty.
2. Customers outside the US are responsible for shipping charges to and from Gefen.
3. Copper cables are limited to a 30 day warranty and cables must be in their original
condition.
The information in this manual has been carefully checked and is believed to be accurate.
However, Gefen assumes no responsibility for any inaccuracies that may be contained
in this manual. In no event will Gefen be liable for direct, indirect, special, incidental, or
consequential damages resulting from any defect or omission in this manual, even if
advised of the possibility of such damages. The technical information contained herein
regarding the features and specications is subject to change without notice.
For the latest warranty coverage information, refer to the Warranty and Return Policy under
the Support section of the Gefen Web site at www.gefen.com.
PRODUCT REGISTRATION
Please register your product online by visiting the Register Product page under the
Support section of the Gefen Web site.
iii
Page 4
DVI ELR Lite Extender over one CAT-5
Contacting Gefen Technical Support
Gefen, LLC
c/o Customer Service
20600 Nordhoff St.
Chatsworth, CA 91311
Telephone: (818) 772-9100
(800) 545-6900
Fax: (818) 772-9120
Email: support@gefen.com
Visit us on the Web: www.gefen.com
Technical Support Hours: 8:00 AM to 5:00 PM Monday - Friday, Pacic Time
DVI ELR Lite Extender over one CAT-5 is a trademark of Gefen, LLC.
Gefen, LLC reserves the right to make changes in the hardware, packaging, and any
accompanying documentation without prior written notice.
© 2013 Gefen, LLC. All Rights Reserved.
All trademarks are the property of their respective owners.
Important Notice
iv
iv
Page 5
3GSDI Audio Embedder
DVI ELR Lite Extender over one CAT-5
Operating Notes
• CAT-5 cables should not exceed 200 feet (60 meters). CAT-6 cables should not
exceed 230 feet (70 meters).
• Shielded Twisted-Pair (STP) CAT-5 or CAT-6 cabling is recommended.
However, Un-shielded Twisted-Pair (UTP) CAT-5 or CAT-6 cabling is acceptable.
Shielded cable has an advantage by providing immunity to Electromagnetic
Interference (EMI), cell phones and A/C motors.
vv
Page 6
DVI ELR Lite Extender over one CAT-5
1080P
®
Features and Packing List
Features
• Extends DVI up to 230 feet (70 meters) over one CAT-6A cable
• Extends DVI up to 200 feet (60 meters) over one CAT-5e cable
• Supports resolutions up to 1080p Full HD and 1920 x 1200 (WUXGA)
• EDID management for rapid integration of source and display
• Enable/Disable switches for HDCP and HPD pass-through
• Locking power supplies
• Surface-mountable
The DVI ELR Lite Extender over one CAT-5 ships with the items listed below. If any of
these items are not present in your box when you rst open it, immediately contact your
dealer or Gefen.
• 1 x DVI ELR Lite Extender over one CAT-5 (Sender unit)
• 1 x DVI ELR Lite Extender over one CAT-5 (Receiver unit)
• 1 x 6 ft. dual-link DVI cable (M-M)
• 2 x 5V / 2.6A DC locking power supply
• 1 x Quick-Start Guide
Packing List
vi
Page 7
Page 8
3GSDI Audio EmbedderDVI ELR Lite Extender over one CAT-5
Table of Contents
01 Getting Started
Sender Unit Layout................................................................................................ 2
Front Panel .................................................................................................... 2
Back Panel .................................................................................................... 3
Bottom Panel ................................................................................................. 4
Receiver Unit Layout ............................................................................................. 5
Front Panel .................................................................................................... 5
Back Panel .................................................................................................... 6
Installation ............................................................................................................. 7
Connecting the DVI ELR Lite Extender over one CAT-5 .............................. 7
Sample Wiring Diagram ................................................................................ 7
02 Appendix
DIP Switch Conguration .................................................................................... 10
Specications .......................................................................................................11
viii
Page 9
Page 10
Page 11
DVI ELR Lite
01 Getting Started
Sender Unit Layout................................................................................................ 2
Front Panel .................................................................................................... 2
Back Panel .................................................................................................... 3
Bottom Panel ................................................................................................. 4
Receiver Unit Layout ............................................................................................. 5
Front Panel .................................................................................................... 5
Back Panel .................................................................................................... 6
Installation ............................................................................................................. 7
Connecting the DVI ELR Lite Extender over one CAT-5 .............................. 7
Sample Wiring Diagram ................................................................................ 7
Extender over
One CAT-5
Page 12
Getting Started
Sender Unit Layout
Front Panel
ID Name Description
1 5V DC Connect the included 5V DC power supply to
2 Link This LED indicator will glow bright green
2 3 4
1
this power receptacle.
when power is applied and a CAT-5 cable is
connected between the Sender and Receiver
unit.
If the source is not connected to the Sender
unit, then this LED indicator will ash bright
green.
3 DVI In Connect the DVI source to this port using the
4 Power This LED will glow bright blue when the unit
included DVI cable.
is powered.
page | 2
Page 13
Getting Started
Sender Unit Layout
Back Panel
ID Name Description
1 Link Connect a CAT-5 cable from this jack to the
1
Link jack on the Receiver unit.
page | 3
Page 14
Getting Started
Sender Unit Layout
Bottom Panel
1
ID Name Description
1 DIP switches Used for troubleshooting purposes only.
See DIP Switch Conguration for more
information.
page | 4
Page 15
Getting Started
Receiver Unit Layout
Front Panel
ID Name Description
1 5V DC Connect the included 5V DC power supply to
2 Link This LED indicator will glow bright green
2 3 4
1
this power receptacle.
when power is applied and a CAT-5 cable is
connected between the Sender and Receiver
unit.
If the display (sink) is not connected to the
Receiver unit, then this LED indicator will
ash bright green.
3 DVI In Connect the DVI source to this port using the
4 Power This LED will glow bright blue when the unit
included DVI cable.
is powered.
page | 5
Page 16
Getting Started
Receiver Unit Layout
Back Panel
ID Name Description
1 Link Connect a CAT-5 (or better) cable from this
jack to the Link jack on the Sender unit.
1
page | 6
Page 17
Getting Started
Installation
Page Title
Connecting the DVI ELR Lite Extender over one CAT-5
1. Use the included DVI cable to connect the DVI source to the DVI In port
on the Sender unit.
2. Connect the Receiver unit to the display using another DVI cable.
3. Connect a CAT-5 (CAT-5e or better is recommended) cable, up to 200 feet (60 meters)
from the Link jack on the Sender unit to the Link jack on the Receiver unit.
If CAT-6a cable is being used, then the cable length can be up to 230 feet (70 meters).
4. Connect the included 5V DC locking power supplies to the Sender and Receiver unit.
Do not overtighten the locking power connectors.
5. Connect the AC power cord from the power supply to an available electrical outlet.
Sample Wiring Diagram
Sender
CAT5 CABLE
DVI CABLE
DVI Source
Receiver
DVI Display
EXT-DVI-1CAT5-SR
page | 7
Page 18
Page 19
DVI ELR Lite
02 Appendix
DIP Switch Conguration .................................................................................... 10
Specications .......................................................................................................11
Extender over
One CAT-5
Page 20
Appendix
DIP Switch Conguration
On the bottom panel of the DVI ELR Lite Extender over one CAT-5 Sender Unit is a bank of
4 DIP switches. Remove the piece of colored tape to reveal the DIP switch bank.
These DIP switches provide control over EDID management, Hot-Plug Detect, and HDCP.
DIP switch 4 is not used. These DIP switches are used for troubleshooting purposes, only.
Sender Unit
DIP Switch Setting Description
1 OFF Uses the local (internal) EDID instead of
ON (default) Uses the downstream EDID. Both DDC
2 OFF (default) Forces HPD high.
ON HPD is passed through.
3 OFF (default) Enables HDCP when using HDMI sources.
ON Disables HDCP. If a DVI source is being
4 NOT USED
Bank of 4 DIP
switches
the downstream EDID (from the display).
This EDID provides generic video/audio
support which is compatible with most
displays.
and HPD (Hot-Plug Detect) are passed
through, allowing the full audio/video
capabilities of the display to be used.
NOTE: The DVI ELR Lite Extender does
not support HDCP with DVI sources.
used, set this DIP switch to the ON
position.
In order to use this mode, DIP Switch #1
must be off.
page | 10
Page 21
Appendix
Specications
Supported Formats
Resolutions (max.) • 1920 x 1200 (WUXGA)
Electrical
Maximum Pixel Clock • 165 MHz
Power Indicator • 1 x LED, blue
Link Indicator • 1 x LED, green
Connectors
Input (Sender) • 1 x DVI-I, 29-pin, female (digital only)
Output (Receiver) • 1 x DVI-I, 29-pin, female (digital only)
Link (Sender / Receiver) • 1 x RJ-45
• 1080p Full HD
Control
DIP Switches (Sender unit) • 4 x DIP switches
Operational
Power Input (Sender / Receiver) • 1 x 5V DC
Power Consumption (Sender / Receiver) • 10W per unit (max.)
Operating Temperature • +32 to 113 °F (0 to +45 °C)
Operating Humidity (non-condensing) • 0 to 90% RH
Physical
Dimensions (W x H x D) • 4.3” x 1” x 4.3”
Unit Weight (each) • 0.36 lbs (0.16 kg)
for EDID management, HPD, and HDCP
(110mm x 26mm x 86mm)
page | 11
Page 22
Stretch it, Switch it, Split it, Control it.
Gefen’s got it. ®
20600 Nordhoff St., Chatsworth CA 91311
1-800-545-6900 818-772-9100 fax: 818-772-9120
www.gefen.com support@gefen.com
Pb
This product uses UL or CE listed power supplies.
Loading...