Page 1
*Preferred
600 MHz
4K ULTRA
60Hz, 4:4:4
DisplayPort 1.2 Extender
™
over one SC-Terminated Fiber-Optic Cable
EXT-DP-4K600-1SC
User Manual
Release A1
Page 2
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this product near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install or place this product near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong are provided for
your safety. If the provided plug does not t into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specied by the manufacturer.
12. To reduce the risk of electric shock and/or damage to this product, never handle or
touch this unit or power cord if your hands are wet or damp. Do not expose this
product to rain or moisture.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualied service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally,
or has been dropped.
15. Batteries that may be included with this product and/or accessories should never be
exposed to open ame or excessive heat. Always dispose of used batteries
according to the instructions.
ii
Page 3
Warranty Information
Gefen warrants the equipment it manufactures to be free from defects in material and
workmanship.
If equipment fails because of such defects and Gefen is notied within two (2) years from
the date of shipment, Gefen will, at its option, repair or replace the equipment, provided
that the equipment has not been subjected to mechanical, electrical, or other abuse or
modications. Equipment that fails under conditions other than those covered will be
repaired at the current price of parts and labor in effect at the time of repair. Such repairs
are warranted for ninety (90) days from the day of reshipment to the Buyer.
This warranty is in lieu of all other warranties expressed or implied, including without
limitation, any implied warranty or merchantability or tness for any particular purpose, all of
which are expressly disclaimed.
1. Proof of sale may be required in order to claim warranty.
2. Customers outside the US are responsible for shipping charges to and from Gefen.
3. Copper cables are limited to a 30 day warranty and cables must be in their original
condition.
The information in this manual has been carefully checked and is believed to be accurate.
However, Gefen assumes no responsibility for any inaccuracies that may be contained
in this manual. In no event will Gefen be liable for direct, indirect, special, incidental, or
consequential damages resulting from any defect or omission in this manual, even if
advised of the possibility of such damages. The technical information contained herein
regarding the features and specications is subject to change without notice.
For the latest warranty coverage information, refer to the Warranty and Return Policy under
the Support section of the Gefen Web site at www.gefen.com.
iii
Page 4
Contacting Gefen Technical Support
Technical Support
(707) 283-5900 (800) 472-5555
8:00 AM to 5:00 PM Monday - Friday, Pacic Time
Email
support@gefen.com
Web
http://www.gefen.com
Mailing Address
Gefen
Core Brands, LLC
c/o Customer Service
1800 S McDowell Blvd
Petaluma, CA 94954 USA
Product Registration
Register your product here: http://www.gefen.com/kvm/Registry/Registration.jsp
iviv
Page 5
Operating Notes
• This product operates with SC-terminated single strand OM3 or OM4 (50/125 μm)
multimode ber optic cable. Single mode ber is not supported.
4K 600 MHz DisplayPort 1.2 Extender over one SC-Terminated Fiber Optic Cable is a trademark of Core Brands,
© 2017 Core Brands, LLC. All Rights Reserved. All trademarks are the property of their respective owners.
Core Brands, LLC reserves the right to make changes in the hardware, packaging, and any accompanying documentation
LLC.
without prior written notice.
Pb
This product uses UL or CE listed power supplies.
vv
Page 6
Features and Packing List
Features*
• Supports Full-Bandwidth 4K 60 Hz 4:4:4 (600 MHz)
• Fully compliant with DisplayPort 1.2 standard
• Supports WQUXGA (4K; 3840x2400), 4K Ultra HD (3840 x 2160), and
• 4K Cinema - DCI (4096 x 2160) at 60Hz, 4:4:4
• Extension up to 200m (660 feet) over one (1) SC-terminated multi-mode
• OM3 or better (50/125um) ber-optic cable
• HDCP 2.2, HDCP 1.4, and DPCP compliant
• Supports DisplayPort Auxiliary/l²C channel
• Supports DisplayPort Multi-stream technology
• Compact enclosures are easy to install and can be hidden away.
• Sturdy metal construction of the enclosures help provide further immunity against
• Electro-Magnetic Interference (EMI) and radiated noise (RFI).
• Plug & Play – no conguration or set-up required for most applications
• EQ switches on Sender & Receiver ensure compatibility with most sources & displays
• Medical Safety (EN 60601-1) & EMC Compliant (EN 60601-1-2) when used with two
EXT-PS52AU-M-1.3-6-AL power supplies (available separately)
*Features and specications are subject to change without notice. All trademarks and registered trademarks are
properties of their respective owners. Copyright© 2017 Core Brands, LLC
Packing List
The following items are shipped with the 4K 600 MHz DisplayPort 1.2 Extender over one
SC-Terminated Fiber Optic Cable. If any of these items are not present in the box when
you rst open it, immediately contact your dealer or Gefen.
• 1 x EXT-DP-4K600-1SC-TX - Sender unit
• 1 x EXT-DP-4K600-1SC-RX - Receiver unit
• 2 x DisplayPort Male-to-Male cables, 6 feet
• 2 x USB-to-DC cables, 2.3 feet
• 2 x EXT-PS52AIP-1.3-6-AL power supplies and 2 sets of regional AC plugs (US, UK,
EU, and AU)
• 1 x Quick Start Guide
vi
Page 7
This page left intentionally blank.
Page 8
Table of Contents
1 Getting Started
Introduction............................................................................................................ 2
Sender Unit ................................................................................................... 2
Receiver Unit ................................................................................................. 4
Installation ............................................................................................................. 6
Connection Instructions ................................................................................. 6
EQ Switch Conguration ............................................................................... 6
Sample Wiring Diagram ................................................................................ 7
2 Appendix
Specications ...................................................................................................... 10
Index.....................................................................................................................11
viii
Page 9
This page left intentionally blank.
Page 10
This page left intentionally blank.
Page 11
4K 600 MHz DisplayPort 1.2 Extender
over one SC-Terminated Fiber-Optic Cable
1 Getting Started
Page 12
Link
5V DC
Introduction
Input
Link
EQ
EXT-DP-4K600-1SC-TX
Off DE
Link
5V DC
Getting Started
Sender Unit
21
Link
5V DC
®
4K 600 MHz
DisplayPort Extender
over one Fiber
Sender
53 4
EXT-DP-4K600-1SC-TX
Link
Input
page | 2
Off DE
EQ
Page 13
ID Name Description
1 Link Connect an SC-terminated multimode ber
Getting Started
2 5V DC Connect the included 5V DC power supply or
optic cable from this connector to the Fiber
connector on the Receiver unit.
USB to DC cable to this power receptacle.
Introduction
3 Link Under normal operating conditions, this
4 Input Use the included DisplayPort cable to
5 Off / DE De-emphasis switch. By default this is
LED indicator will glow bright green.
connect to a DisplayPort 1.2 source.
set to the “Off” position. See EQ Switch
Conguration (page 6) for more
information.
page | 3
Page 14
Getting Started
Link
5V DC
Output
Link
EQ
EXT-DP-4K600-1SC-RX
Off PE
Link
5V DC
Introduction
Receiver Unit
21
Link
5V DC
®
4K 600 MHz
DisplayPort Extender
over one Fiber
Receiver
74 5
EXT-DP-4K600-1SC-RX
Link
Output
page | 4
Off PE
EQ
Page 15
ID Name Description
1 Link Connect an SC-terminated multimode ber
Getting Started
2 5V DC Connect the included 5V DC power supply or
optic cable from this connector to the Fiber
connector on the Receiver unit.
USB to DC cable to this power receptacle.
Introduction
3 Link Under normal operating conditions, this
4 Input Use the included DisplayPort cable to
5 Off / PE Pre-emphasis switch. By default this is
LED indicator will glow bright green.
connect to a DisplayPort 1.2 display.
set to the “Off” position. See EQ Switch
Conguration (page 6) for more
information.
page | 5
Page 16
Installation
Link
5V DC
Link
5V DC
Connection Instructions
► Video
1. Connect the included DisplayPort cable between the DisplayPort 1.2 source and the
Getting Started
Input port on the Sender unit.
2. Connect a DisplayPort 1.2 display to the Output port on the Receiver unit, using the
included DisplayPort cable.
► Fiber
3. Connect a single SC-terminated OM3 or OM4 (50/125 μm) multimode ber optic
cable, up to 660 feet (200 meters), between the Link port on the Sender unit and the
Link port on the Receiver unit.
► Power
4. Connect the included 5V DC power supplies to the 5V DC port on both the Sender
and Receiver unit.
5. Connect the opposite end of the power supplies to available electrical outlets.
6. The Link indicators on both units will light once all connections are complete and the
units, the source, and the display are powered up.
EQ Switch Configuration
Sender unit - By default, this switch is in the “Off” position. Set the switch to the “DE”
(signal de-emphasis) setting, if the source output is very high.
EXT-DP-4K600-1SC-TX
Off DE
Link
Input
EQ
Receiver unit - By default, this switch is set to the “Off” position . Set to the “PE”
(signal pre-emphasis) position if the sink device requires a higher than normal input level.
EXT-DP-4K600-1SC-RX
Link
Output
Off PE
EQ
page | 6
Page 17
Getting Started
Sample Wiring Diagram
4K 600 MHz DisplayPort 1.2
Source
4K 600 MHz DisplayPort 1.2
Extender
(Sender unit)
®
DisplayPort Extender
4K 600 MHz
over one Fiber
Sender
5V DC
Link
4K 600 MHz DisplayPort 1.2
Extender
(Receiver unit)
®
DisplayPort Extender
4K 600 MHz
over one Fiber
Receiver
Off PE
EQ
EXT-DP-4K600-1SC-RX
Output
Link
DISPLAYPORT CABLE
FIBER OPTIC (SC-SC) CABLE
4K 600 MHz DisplayPort 1.2
Display
EXT-DP-4K600-1SC
page | 7
Page 18
Page 19
4K 600 MHz DisplayPort 1.2 Extender
over one SC-Terminated Fiber-Optic Cable
2 Appendix
Page 20
Specications
Supported Formats
Video • 3840 x 2160 @ 60 Hz
Appendix
Connectors & Indicators
Input (Sender) • 1 x DisplayPort, 20-pin, female
Output (Receiver) • 1 x DisplayPort, 20-pin, female
Link (Sender / Receiver) • 1 x SC-type, female
Link (Sender / Receiver) • 1 x LED, green
Power • 1 x 1.3 mm barrel jack
Operational
Video Bandwidth • 21.6 Gbps (5.4 Gbps per lane, 4 lanes)
Optical Wavelength • 850 nm
Power Input • 5V DC
Power Consumption (Sender) • 1.75 W
Power Consumption (Receiver) • 2.0 W
Optical Power Budget • 6.5 dB
Operating Temperature • +32 to +122 ºF (0 to +50 ºC)
Operating Humidity • 10% to 85% RH, non-condensing
Storage Temperature • -4 to +158 °F (-20 to +70 °C)
Storage Humidity (RH) • 10% to 85% RH, non-condensing
• WQUXGA (4K; 3840x2400 @ 60Hz)
• 4K Ultra HD (3840 x 2160 @ 60Hz)
• 4K Cinema - DCI (4096 x 2160 60Hz)
Physical
Dimensions (W x H x D)
(Sender / Receiver),
not including connectors
Unit Weight (each) • 4.8 oz. (0.135 kg)
Shipping Weight • 2.5 lbs (1.2 kg)
NOTE: Features and specications are subject to change without notice. All trademarks and registered trademarks are
properties of their respective owners. Copyright© 2017 Core Brands, LLC
• 1-3/4” x 7/8” x 3-1/8” (45 mm x 22 mm x
79 mm)
page | 10
Page 21
Index
C
Appendix
D
E
F
I
L
Conguration
EQ switch 6
Connection Instructions 6
De-emphasis
EQ switch 3
DisplayPort
port 3, 5
EQ
Off / DE 3
Off / PE 5
Features vi
Installation 6
Link
LED 3, 5
port 3, 5
T
Table of Contents viii
Technical Support iv
W
Warranty Information iii
Wiring Diagram 7
O
Off / DE
switch 3
Operating Notes v
P
Packing List vi
Power
port 3, 5
Pre-emphasis
EQ switch 5
S
Safety Instructions ii
Sender Unit 2
Specications 10
page | 11
Page 22
Stretch it. Switch it. Split it. Gefen’s got it. ®
*Preferred
20600 Nordhoff St., Chatsworth CA 91311
1800 S McDowell Blvd. Petaluma CA 94954, USA
1-800-545-6900 818-772-9100 fax: 818-772-9120
(707) 283-5900 (800) 472-5555
www.gefen.com support@gefen.com
Loading...