Gefen CAT5-5500, EXT-CAT5-5500 User Manual

Page 1
CAT5•5500
USER MANUAL
www.gefen.com
Page 2
ASKING FOR ASSISTANCE
Technical Support:
Telephone (818) 772-9100 (800) 545-6900
Fax (818) 772-9120
Technical Support Hours:
Write To:
Gefen Inc. c/o Customer Service 20600 Nordhoff St. Chatsworth, CA 91311
support@gefen.com www.gefen.com
Notice
Gefen Inc. reserves the right to make changes in the hard ware, packaging and any
accompanying doc u men ta tion without prior written notice.
CAT5•5500 is a trademark of Gefen Inc.
© 2007 Gefen Inc., All Rights Reserved
Page 3
TABLE OF CONTENTS
1
2
3
4
5
6
7
8
9
10
11
Introduction How It Works CAT5•5500S Front Panel Layout CAT5•5500R Front Panel Layout CAT5•5500S Back Panel Layout CAT5•5500 Back Panel Function Descriptions CAT5•5500R Back Panel Layout CAT5•5500R Back Panel Functions Descriptions CAT5 Cable Length Setup Link Cable Wiring Diagrams CAT5•5500 - Wiring Diagram
12
13
System Specifi cations Warranty
Page 4
OPERATION NOTES
READ THESE NOTES BEFORE IN STALL ING
OR OPERATING THE CAT5•5500 SYSTEM
* Industry standard Category-5 (CAT-5) cables are used to operate CAT5•5500 system.
Linking the CAT5•5500 sender and receiver units together requires one CAT-5 cable to extend the fi rst monitor. A second CAT-5 cable is required to extend the second monitor signal and a third CAT-5 cable is required to extend USB and audio.
* When monitors are used in the local and remote locations, the video monitors must be able to use the same resolution. This pertains to monitors placed remotely, and those di­vided between local and remote locations. The video monitors will not initialize correctly at start-up if they are unable to sync the same resolution of the local monitors.
* The CAT5•5500 units are housed in a metal box for better RF shielding.
Page 5
INTRODUCTION
Thank you for purchasing the new ex•tend•it CAT5•5500 series by Gefen, Inc. The ex•tend•it CAT5•5500 by Gefen allows users the benefi ts of extending USB, audio,
and video signals beyond the desktop. In a growing number of applications, broadcast stations and production facilities there is a need to control a computer remotely. The keyboard, mouse, and video monitor are relocated to the remote side. A CPU may need to be shared between several users or moved to another room because of annoying fan noise.
The CAT5•5500 series can be used to extend computers with noisy fans, printers, hard drives, scanners, cameras, keyboards, mouse, and any other USB-type peripherals. The CAT5•5500 has the potential to cover the distance of 330 feet over industry standard Category 5 (CAT-5) cables. One can connect additional CAT5•5500 series to the same computer, allowing access to the same computer from other locations up to 330 feet apart.
1
Page 6
HOW IT WORKS
CONTENTS
The CAT5•5500 system consists of: (1) CAT5•5500S sender unit
(1) CAT5•5500R receiver unit (2) 5 VDC power supplies (2) Video cables (6FT) (1) USB cable (06FT) (1) Audio cable (06FT) (1) User Manual
HOW IT WORKS
In its most basic application, the CAT5•5500S sender unit resides next to the com put er. Supplied with the system, VGA, audio, and USB cables, they con nect the computer to the CAT5•5500S sender unit.
The CAT5•5500R receiver unit is placed next to the monitors and USB peripherals at the remote location. The monitors and USB peripherals are connected to the CAT5•5500R, sim i lar to the way they are connected to the back of the com put er (PC or Macintosh).
Industry standard Category 5 (CAT-5) cables are used to link CAT5•5500S send er and CAT5•5500R re ceiv er units together. The CAT5•5500 model requires one CAT­5 cable to extend the fi rst monitor. A second CAT-5 cable is required to extend the second monitor signal and a third CAT-5 cable is required to extend USB and audio.
2
Page 7
CAT5•5500S FRONT PANEL DE SCRIP TIONS
RONT PANEL FUNCTION DESCRIPTIONS
F
Power On Indicator - Indicates that the unit is on and plugged in.1
1
3
Page 8
CAT5•5500R FRONT PANEL LAYOUT
2
1
Front Panel Function Descriptions
F2 - Fine focus adjustment for monitor 2
1
B2 - Adjusts the brightness for monitor 2
2
F1 - Fine focus adjustment for monitor 1
3
B1 - Adjusts the brightness for monitor 1
4
POWER ON INDICATOR - Indicates that the unit is plugged in and powered on
5
4 5
3
4
Page 9
CAT5•5500S BACK PANEL LAYOUT
10
9
8
7
12 3 4 5 6
5
Page 10
CAT5•5500S BACK PANEL FUNCTIONS
1
2
3
4
5
6
7
8
9
10
POWER - 5 VDC external power supply MONITOR 1 - HD15 output connects to the monitor 1 for local video VIDEO IN 1 - HD15 input from computer MONITOR 2 - HD15 output connects to the monitor 2 for local video VIDEO IN 2 - HD15 input from computer CAT5 2 Video 2 - RJ-45 input extends video input 2 with CAT-5 cable CAT5 2 Video 1 - RJ-45 input extends video input 2 with CAT-5 cable CAT5 1 USB/AUDIO - RJ-45 input extends USB and audio signals with CAT-5
cable
AUDIO IN - Audio Mini Jack input from computer USB IN - USB Input from computer
6
Page 11
CAT5•5500R BACK PANEL LAYOUT
8
7
6
5
4
3
2
1
7
Page 12
CAT5•5500R BACK PANEL FUNC TIONS
1
POWER - 5 VDC external power supply
2
VIDEO OUT 1 - HD15 output connecting to the video monitor 1
3
VIDEO OUT 2 - HD15 output connecting to the video monitor 2
4
AUDIO - Audio Mini Jack
5
CAT-5 Video 2 - RJ-45 input connects CAT-5 cable to receive extended video
signals
6
CAT-5 Video 1 - RJ-45 input connects CAT-5 cable to receive extended video
signals
7
CAT5 USB/Audio - RJ-45 input connects CAT-5 cable to receive extended USB
and audio signals
8
USB OUT - USB Outputs - Connects to USB devices
8
Page 13
HOW TO ADJUST THE PICTURE
Jumper settings are used to set the focus of the picture and characters to the best possible sharpness. The jump ers in the CA T5•5500R are set at the factory as shown in the diagram below. The fi rst step to adjusting the video is to have the CAT5•5500S and CAT5•5500R con nect ed together with the CAT-5 cable that is going to be used in the in stal la tion. Then set your computer to the resolution and refresh rate that you will be using most frequently be using. Then open up the CA T5•5500R by un screw ing the bottom three screws on back end of the box. Then two screws on each side of the box and the top. That is 9 screws in total that need to be removed. Lastly the 4 hex bolts around the Monitor Out port and the Video In port need to also be removed. After that look at some text on the monitor and set the jumpers to the recommended jumper setting based on the length of your CAT-5 cable. If you still see some smear ing try moving all the jumpers up or down one from the recommended setting. If you see smearing of just one color adjust an individual jumper for the color that is smearing (it can be two colors). Repeat the same steps for monitor 2
Recommended Jumper Settings
Cable length 0-132 feet
*As shown in picture
133-198 feet
199-264 feet
265-330 feet
Jumper Settings
Video 1 on the
left
4 3 2 1
Po si tion
Red
Green
Blue
Video 2 on the
right
Red
Green
Blue
9
Page 14
CAT5 LINK CABLE - WIRING DIAGRAM
8 1
1
2
RJ-45 Jack
Orange
White/Orange
White/Green
3
4
Blue
5
6
7
Green
White/Blue
White/Brown
8
Brown
1
2
3
RJ-45 Jack
4
5
10
6
7
8
8
1
Page 15
CAT5•5500 WIRING DIAGRAM
11
Page 16
SPECIFICATIONS
Video Amplifi er Bandwidth .................................................................................. 350 MHz
Actual Bandwidth ................................................................................................ 120 MHz
Input Video Signal ......................................................................................... 1.2 Volts p-p
Input Sync Signal ................................................................................... 5 Volts p-p (TTL)
Horizontal Frequency Range ........................................................................... 15-70 KHz
Vertical Frequency Range .............................................................................. 30 - 170 Hz
Video In .................................................................................................................. HD-15
Focus/Brightness Control ............................................................................. 25 to 450 FT
Video out ................................................................................................................ HD-15
Link Connector ........................................................................................................ RJ-45
USB - "A" Connector ........................................................................................... USB Out
USB - "B" Connector ............................................................................ USB Device Input
Power Consumption ................................................................................ 15 Watts (max.)
Power Supply ......................................................................................... 5 VDC (Ex ter nal)
Dimensions Send Unit .................................................................... 16”W x 1 3/4”H x 4”D
Dimensions Receive Unit .................................................................. 8”W x 1 3/4”H x 4”D
Rack Mountable ....................................................................................... 2 Rack Spaces
Shipping Weight ....................................................................................................... 9 Lbs
12
Page 17
WARRANTY
Gefen Inc. warrants the equipment it manufactures to be free from defects in material and workmanship.
If equipment fails because of such defects and Gefen Inc. is notifi ed within two (2) year from the date of shipment, Gefen Inc. will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifi cations.
Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair. Such repairs are warranted for ninety (90) days from the day of reshipment to the Buyer.
This warranty is in lieu of all other warranties expressed or implied, including without limitation, any implied warranty or merchantability or fi tness for any particular purpose, all of which are expressly disclaimed.
1. Proof of sale may be required in order to claim warranty.
2. Customers outside the US are responsible for shipping charges to and from Gefen.
3. Copper cables are limited to a 30 day warranty and cable must be free from any scratches, markings, and neatly coiled.
The information in this manual has been carefully checked and is believed to be accurate. However, Gefen Inc. assumes no responsibility for any inaccuracies that may be contained in this manual. In no event will Gefen Inc., be liable for direct, indirect, special, incidental, or consequential damages resulting from any defect or omission in this manual, even if advised of the possibility of such damages. The technical information contained herein regarding CAT5•5500 features and specifi cations is subject to change without notice.
13
Loading...