GE Digital EP-5111, EP-5112, EP-5212, EP-5261, EP-5311 Data sheet
...
RSTI-EP Slice I/O
Module Status
LED
Channel Status
LED
GE provides several RSTi-EP specialty modules, which can be used to meet specific
Digital pulse width modulation modules can control from 0.5A to 2A
GFK-2962B
August 2016
Specialty Modules
EP-5111, EP-5112, EP-5212, EP-5261, EP-5311, EP-5422, EP-5442
needs in your system. Each module has a Module Status LED and each channel has
a LED for visual indication of connectivity.
The counter module EP-5111 can read one square-wave signal (1 channel) (for
example, from an incremental encoder) with a maximum input frequency of 100
kHz. The 32-bit counter can count up or down within a predetermined range of
values.
Specialty Module
The digital counter module EP-5112 can read two square-wave signals (2 channels)
(for example, from an incremental encoder) with a maximum input frequency of 100
kHz. Depending on the operating mode, both 32-bit counters can count up or down
independent of each other in a preset range of values. The counters can be
controlled via software by setting the appropriate control word.
The digital counter module EP-5212 can read frequency of one square-wave signal
(1 channel) from one or two external sensors with a maximum input frequency of
100 kHz. Frequencys to be counted are applied to channel CH0 and/or channel CH1,
the measurement will be started via control word 1 and 2 respectively. Measuring
cycles can be defined in μs. The longer the measuring cycle the more exactly the
measurement.
The digital pulse width modulation modules EP-5422 and EP-5442 are used for the
control of small motors with current requirements of 0.5 A up to 2 A which can also
be used for the control of valve flaps. The switching frequencies are adjustable up to
40 kHz and, in addition to this, the push/pull output levels can be used for motor
activation; for example: change of rotation direction. As with all modules of the RSTiEP system, the characteristics are outstanding – from the modular design and the
interchangeable electronics to the removable plug-in terminal strip.
The RSTi-EP station is usually installed on a horizontally positioned DIN rail.
Installation on vertically positioned DIN rails is also possible.
Modules should to be allowed to de-energize for a minimum 10 seconds after
power down, prior to starting any maintenance activity.
Refer to the RSTi-EP Slice I/O User Manual (GFK-2958) for additional information.
Refer to the RSTi-EP Power Supply Reference Guide, a software utility available on
PME V9.00, for detailed power-feed requirements.
Module Features
Spring style technology for ease of wiring
DIN rail mounted
Double-click installation for positive indication of correct installation
Compatible for 2 and 3 wire connection
32-bit counter, 24 V DC
Counting frequency 100 kHz max (A/B channel, 1/2/4- times sampling or pulse
and direction, invertible)
Gate input (hardware gate, HW gate), reset input, digital output controlled by an
internal comparator
Alarm and diagnostic function with μs time stamp
Digitally adjustable input filter to suppress interferences(17 filter frequencies
gradually adjustable between 3 Hz and 187 kHz)
SSI Encoder Interface Serial Communication module
© 2015 - 2016 General Electric Company.
*
Indicates a trademark of General Electric Company and/or its subsidiaries. All other trademarks are the property of their respective
owners.
2 RSTi-EP Slice I/O Specialty Modules
Item
EP-5111
EP-5112
EP-5212
System Data
Data
Process, parameter, and diagnostic data depend on the network adapter used.
Interface
RSTi-EP System bus
System bus transfer rate
48 Mbps
Galvanic isolation
--
500 V DC between the current paths
Inputs
Number of counter inputs
1 2 2
Incremental encoders and other input characteristics for
sensor types 1 and 3 are in accordance with EN 61131-2
Adjustable between 3 Hz
Low input voltage
< 5 V
High input voltage
> 11 V
Max. input current per
channel
Sensor supply
Yes
Sensor connection
2-wire and 3-wire
Reverse polarity protection
Yes
Module diagnostics
Yes
Individual channel
diagnostics
Counter width
32 bits
Maximum input frequency
100 kHz
Latch, gate, reset input
Yes
--
--
Pulse and direction / AB
sampling
Status, alarm, diagnostics
Status indicator
Yes
Process alarm
Yes, parametrizable
Yes, parametrizable
--
Diagnostic alarm
Yes
Yes
--
Outputs
Number 1 --
--
Output Current
0.5 A
--
--
Reverse polarity protection
Yes
--
--
Module diagnosis
Yes
--
--
Individual channel
diagnosis
GFK-2962B
Ordering Information
Module Description
EP-5111 1 Channel High Speed Counter, AB 100 kHz 1 DO 24VDC, 0.5A
EP-5112 2 Channel High Speed Counter, AB 100 kHz
EP-5212 2 Channel Frequency Measurement, 100 kHz
EP-5422 2 Channels PWM Output, Positive Logic, 24VDC, 2.0 A
EP-5442 2 Channels PWM Output, Positive Logic, 24VDC, 0.5 A
EP-5261
EP-5311 SSI Encoder, BCD or Gray-Code Format, 5/24 VDC
1 Channel Serial Communications, 232, 422, 485
Specifications
Type
Input filter Filter time adjustable from 0,01 to 1 ms
--
and 187 kHz (333 ms and
5 μs)
3.5 mA
Yes Yes No
Mode of operation
Pulse and direction / AB mode
with 1-, 2-, 4-times sampling
Yes -- --
mode with 1-, 2-, 4-times
Pulse rising edge
RSTi-EP Slice I/O Specialty Modules 3
EP-5111
EP-5112
EP-5212
Supply
Supply voltage
20.4V – 28.8V
Current consumption from
system current path I
Current consumption from
output current path Iin
35 mA plus output current for
the digital output
35 mA plus sensor supply
current
General Data
Operating temperature
-20°C to +60°C (-4 °F to +140 °F)
Storage temperature
-40°C to +85°C (-40 °F to +185 °F)
Air humidity
(operation/transport)
Width
11.5 mm (0.45 in)
Depth
76 mm (2.99 in)
Height
120 mm (4.72 in)
Weight
83 g (2.93 oz)
72 g (2.54 oz)
83 g (2.93 oz)
EP-5261
System data
Data
Process, parameter and diagnostic data depend on the network
Interface
RSTi-EP I/O communication bus
System bus transfer rate
48 Mbps
Serial Interface
Number
1
Type
RS-232, RS-485, RS-422, parameterizable
Transfer rate
300 – 115200 Bps, parameterizable
Supply voltage
5VDC or 24VDC
Current of power supply output
max. 500 mA
Standards RS232
DIN 66020, DIN 66259, EIA-RS232C, CCITT V.24/V.28
Standards RS485/RS422
120 Ω, parameterisable
Short-cicuit proof
Yes
Module diagnosis
Yes
Individual channel diagnosis
Yes
Supply
Supply voltage
20.4V – 28.8V
Current consumption from system current path I
,
8 mA
Current consumption from input current path Iin
16 mA + load
General Data
Weight
92 g (3.25 oz)
For additional general data, refer to the section, General Technical Data for I/O Modules.
GFK-2962B
SYS
5% to 95%, noncondensing as per IEC 61131-2
8 mA
35 mA
Adapter used (refer to the table in the section, Order and
Arrangement of the Modules)
SYS
For public disclosure
4 RSTi-EP Slice I/O Specialty Modules
EP-5311
System Data
Process, parameter and diagnostic data depend on the network
Interface
RSTi-EP I/O communication bus
System bus transfer rate
48 Mbps
Number of channels
1
Type
SSI (Differential RS-422)
SSI transfer rate
125 kHz – 2 MHz
Delay time
1 μs – 64 μs
Data width
8 – 32 Bit
Data format
Binary / Gray-Code
SSI mode
Listening / Master
Sensor supply
500 mA (24 V DC) / 400 mA (5 V DC)
Reverse polarity protection
Yes
Module diagnosis
Yes
Individual channel diagnosis
No
Cable length
max. 320 m (1049.( ft) at 125 kHz; shielded
Supply
Supply voltage
20.4V – 28.8V
Current consumption from system current path
8 mA
Current consumption from input current path Iin
25 mA + sensor supply current
General Data
Weight
87 g (3.07 oz)
For additional general data, refer to the section, General Technical Data for I/O Modules.
GFK-2962B
Data
Adapter used (refer to the table in the section, Order and Arrangement
of the Modules)
I
,
SYS
RSTi-EP Slice I/O Specialty Modules 5
EP-5422
EP-5442
System Data
Data
Process, parameter, and diagnostic data depend on the network adapter used.
Interface
RSTi-EP system bus
System bus transfer rate
48 Mbps
48 Mbps
Outputs
Number
2
2
Type
PN output stage
Response time
< 0.1 μs
< 0.1 μs
Period duration
25 μs t o 175 ms (40 kHz to 6 Hz)
per channel
0.5 A
per channel
2 A
per module
1 A
per module
4 A
Resistive load
(min. 47 Ω)
Resistive load
(min. 12 Ω)
Inductive load
(DC 13)
Inductive load
(DC 13)
Lamp load (12 W)
static, 6 Hz to 40 kHz
Lamp load (48 W)
6 Hz to 40 kHz
Actuator connection
2-wire, 3-wire, 3-wire + FE
Actuator supply
max. 2 A per plug, total max. 4 A
max. 2 A per plug, total max. 8 A
Pulse/period ratio
0–100 % PN-switching or P-switching, adjustable
Short-circuit-proof
Yes
Response time of the
protective circuit
Module diagnosis
Yes
Individual channel diagnosis
No
Reactionless
Yes
Supply
Supply voltage
20.4V – 28.8V
system current path I
SYS
output current path I
OUT
General Data
Operating temperature
-20°C to +60°C (-4 °F to +140 °F)
Storage temperature
-40°C to +85°C (-40 °F to +185 °F)
(operation/transport)
Width
11.5 mm (0.45 in)
Depth
76 mm (2.99 in)
Height
120 mm (4.72 in)
Weight
77 g (2.72 oz)
82 g (2.89 oz)
GFK-2962B
PN output stage
Max. output current
Switching frequency
Current consumption from
Current consumption from
Air humidity
static, 6 Hz to 40 kHz
static, 6 Hz to 40 kHz
< 100 μs
8 mA
40 mA + Load
5% to 95%, noncondensing as per IEC 61131-2
6 Hz to 40 kHz
6 Hz to 40 kHz
For public disclosure
Loading...