GE Appliances JX2130SH Installation Manual

PART QUANTITY

Trim Frame 1

Bottom Duct 1

Top Bracket 1

Phillips Round-Head 24 Screws (22 required

for installation)

Phillips Flat-Head 5 Screws (4 required for

installation)

Anti-Tip Bracket 1

Bottom Bracket 1

Template 1

PARTS INCLUDED

Questions? Call GE Answer Center at 800.626.2000 or

Visit our Website at:

www.GEAppliances.com

READ CAREFULLY. KEEP THESE INSTRUCTIONS

Installation Built-In Trim Kits Instructions

JX2127 and JX2130

Read these instructions completely and carefully.

•

IMPORTANT – Save these

instructions for local inspector’s use.

•

IMPORTANT – Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions

for future reference.

• For easier installation and personal safety, we recommend that two people install this microwave oven.

• Unplug the microwave oven before attempting installation of this kit.

BEFORE YOU BEGIN

• Skill level – Installation of this appliance requires basic mechanical and electrical skills.

• Completion time – 1-3 hours

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not

covered under the Warranty.

• This kit is UL listed for installation alone or over any General Electric/Hotpoint/RCA single electric wall oven.

TOOLS YOU WILL NEED

#2 Phillips screwdriver

Pencil

Tape measure

Awl or punch

Drill with

⁄64″ bit or #35

FOR YOUR SAFETY:

WARNING – Before beginning the

installation, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

Scissors (optional)

CUTOUT DIMENSIONS

* Min. depth with receptacle outside cabinet 19

⁄2″

Min. depth with receptacle inside cabinet 22″

Installation Instructions

Models 27″ 30″

Height 163⁄4″ 163⁄4″

Width 251⁄2″ 251⁄2″

Depth (min.)* 191⁄2″ or 22″ 191⁄2″ or 22″

On 27″ models, allow 11⁄4″ at the top, 9⁄16″ on the sides and 1″ at the bottom for overlap of the Trim Frame over the edges of the cutout.

On 30″ models, allow 11⁄4″ at the top, 21⁄8″ on the sides and 1″ at the bottom for overlap of the Trim Frame over the edges of the cutout.

Depth

Height

1″ overlap

Width

INSTALL BOTTOM BRACKET AND BOTTOM DUCT

Fit the tab on the bottom bracket into the slot on the back of the bottom duct, and push down until the bracket is flush with the bottom of the duct. Fasten the bottom bracket to the bottom duct by using two bronze round-head screws.

Disconnect the microwave oven before proceeding with the installation.

Remove any loose items inside the microwave oven, including the turntable and turntable support. Carefully turn the microwave oven upside down.

Line up the tabs on the bottom duct with the slots on the bottom of the microwave and insert the tabs into the slots. Secure the bottom duct with four bronze round-head screws as shown.

Front

Rear

Screws

Microwave Oven Upside Down

11⁄4″ overlap

1″ Clearance beyond

Trim Frame

(on all sides)

27″ Models:

⁄16″ overlap

30″ Models: 21⁄8″ overlap

3″ min.

CAUTION

This trim kit uses air flow from the top, bottom and sides of the trim frame. Blocking the air flow can cause the microwave to function improperly and may cause damage to the microwave.

Allow a 1″ clearance beyond the edge of the Trim Frame to provide proper air flow.

+ 2 hidden pages