GE Appliances GFE28HGH Installation Manual

GEAppliances.com

Safety Instructions ............2, 3

Operating Instructions

Features ..........................4, 5

Controls ..........................6–9

Dispenser* ......................... 10

Autofill* ............................11

Water Filter ........................12

Fresh Food Storage Options .....13,14

Climate Zone & Temperature

Controlled Drawer ...............15,16

Freezer ............................17

Automatic Ice maker ...............18

Care and Cleaning ................ 19

Replacing the Lights ................20

Installation Instructions

Preparing to Install the

Bottom Freezer

Re frigerator ....................21, 22

Installing the Refrigerator .......23–33

Installing the Water Line ........34–36

Troubleshooting Tips ......38, 39

Normal Operating Conditions .......37

Truth or Myth .................. 40, 41

Consumer Support

Warranty ..........................42

RPWFE Water Filter Cartridge Limited

Warranty .........................43

Performance Data Sheet ...........44

Consumer Support ........Back Cover

Owner’s Manual and

Installation Instructions

GE and GE Profile™ models

Models that start with PFE, GFE, DFE,

and GNE are Standard Depth Models (SD)

Models that start with GYE, PYE and PWE

are Counter Depth Models (CD)

Réfrigérateurs

Manuel d’utilisation

et instructions

d’installation

Modèles GE et GE Profile™

La section française commence à la

Les numéros de modèle commençant par PFE, GFE,

Les numéros de modèle commençant par GYE, PYE

et PWE sont des modèles de profondeur

DFE, et GNE sont des modèles

de profondeur normale (PN).

de comptoir (PC).

Refrigeradores

page 45

Manual del Propietario e

Instrucciones de Instalación

GE y GE Profile™ modelos

*Select Models Only

La sección en español empieza en la

página 90

Los modelos que comienzan con las letras

PFE, GFE, DFE, y GNE son Modelos con

Write the model and serial numbers here:

Model # ____________________ Serial # ____________________

Find these numbers on a label on the left side, near the middle of the refrigerator compartment.

Los modelos que comienzan con las

letras GYE, PYE y PWE son Modelos con

Profundidad Estándar (SD)

Profundidad de Mesada (CD)

Refrigerators

239D4106P020 49-60716-1 09-14 GE

IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING.

SAFETY

IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING

GE Appliances website

For more information on your refrigerator’s operation, visit www.GEAppliances.com

REFRIGERATOR SAFETY INFORMATION

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety

messages will follow the safety alert symbol and the word “DANGER”, “WARNING”, or “CAUTION”. These words are defined as:

Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

DANGER

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

WARNING

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

CAUTION

IMPORTANT SAFETY INSTRUCTIONS

WARNING

To reduce the risk of fire, explosion, electric shock, or injury when using your

refrigerator follow these basic safety precautions:

 This refrigerator must be properly installed and located in

accordance with the Installation Instructions before it is used.

 Unplug the refrigerator before cleaning and making repairs.  NOTE: Repairs must be performed by a qualified Service

 Replace all parts and panels before operating.  Because of potential safety hazards under certain conditions,

 To prevent suffocation and entrapment hazards to children,

 Do not store or use gasoline or other flammable vapors and

 Power to the refrigerator cannot be disconnected by any

Professional.

we strongly recommend against the use of an extension cord. However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United States) or a CSA certified (in Canada), 3-wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

Remove the fresh food and freezer doors from any refrigerator before disposing of it or discontinuing its use.

liquids in the vicinity of this or any other appliance.

setting on the control panel, refrigerator must be unplugged to remove power.

 Do not allow children to climb, stand or hang on the door handles

or the shelves in the refrigerator. They could seriously injure themselves.

 In refrigerators with automatic ice makers, avoid contact with

the moving parts of the ejector mechanism, or with the heating element that releases the cubes. Do not place fingers or hands on the automatic ice making mechanism while the refrigerator is plugged in.

 Do not clean glass shelves or covers with warm water when

they are cold. Glass shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping or dropping. Tempered glass is designed to shatter into many small pieces if it breaks.

 Keep fingers out of the “pinch point” areas; clearances between

the doors and between the doors and cabinet are necessarily small. Be careful closing doors when children are in the area.

 Do not touch the cold surfaces in the freezer compartment when

hands are damp or wet, skin may stick to these extremely cold surfaces.

 Do not refreeze frozen foods which have thawed completely.  Use a sturdy glass when dispensing ice (on models with ice

dispenser)

INSTALLATION

WARNING

Keep flammable materials and vapors, such as gasoline, away from refrigerator. Failure to do so can result in fire, explosion, or death.

Explosion Hazard.

GEAppliances.com

SAFETY (CONT.)

WARNING

Tip Over Hazard.

Built-in style models (model PYE, CYE, GYE, PWE, CWE, and ZWE) are top heavy, especially with any doors open. These models must be secured with the anti-tip floor bracket to prevent tipping forward, which could result in death or serious injury. Read and follow the entire installation instructions for installing the anti-tip floor bracket packed with your refrigerator.

CONNECTING ELECTRICITY

WARNING

Plug into a grounded 3-prong outlet Do not remove the ground prong Do not use an adapter Failure to follow these instructions can result in death, fire, or electrical shock.

Electrical Shock Hazard.

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.

Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet. Do not use an adapter.

The refrigerator should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate.

A 115 Volt AC, 60 Hz, 15- or 20-amp fused, grounded electrical supply is required. This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.

Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.

When moving the refrigerator away from the wall, be careful not to roll over or damage the power cord.

PROPER DISPOSAL OF YOUR OLD REFRIGERATOR

WARNING

Remove fresh-food and freezer doors from the refrigerator, prior to disposal. Failure to do so can result in child entrapment which can lead to death or brain damage.

IMPORTANT:

Suffocation and child entrapment hazard.

Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow the instructions below to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

 Take off the fresh food and freezer doors.  Leave the shelves in place so that children may not easily climb

inside.

Refrigerants

All refrigeration products contain refrigerants, which under federal law must be removed prior to product disposal. If you are getting rid of an old refrigeration product, check with the company handling the disposal about what to do.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

About the features. *

Space-saving ice maker*

Ice maker and bin are located on the door creating more usable storage space.

Showcase LED lighting

LED lighting is positioned throughout the interior to spotlight areas in the refrigerator. LEDs are located under the fresh food door to light the freezer when opened.

Drop-down tray*

Allows for extra door storage when you need it and tucks away when you don’t.

Full-width temperature controlled drawer

(on some models) Adjustable temperature control bin that can accommodate larger items.

Dairy bin*

Separate compartment for your items.

Dual ice maker/Ice bin (on some models)

An ice maker in both compartments gives you more ice whenever you need it .

*Select Models Only

QuickSpace™ shelf*

Functions as a normal full-sized shelf when needed and easily slides back to store tall items below.

Spillproof shelves

Designed to capture your spills for easier clean up.

Anti-slip Mat*

Liner that captures spills, keeps containers from shifting when the door is opened and is easily removable for cleaning.

Removable door bin

Can be removed for those with a wall limiting the door opening.

Climate zone bin

Separate bins for produce storage.

Water filter*

Filters water & Ice

About the features. * GEAppliances.com

Door ice bin*

1. Open left fresh food door.

2. Pull down latch to release bin door.

3. Using handhold lift ice bucket up and out to clear locators in bottom of bin.

4. To replace the ice bucket, set it on the guide brackets and push until the ice bucket seats properly.

5. If bucket cannot be replaced, rotate the Ice Bucket Fork 1/4 turn clockwise.

Drop down dairy bin*

1. Open right fresh food

2. Depress both buttons on lower sides and bin will drop down.

3. Reverse to reinstall.

Ice/water filter

Remove filter/bypass plug

Push the indent on the cover and open filter door. Pull out on filter/bypass plug and pull straight back to remove.

Installing the filter cartridge

Push the indent at the bottom of the cover and open. Lift door and align tabs on filter to filter/holder and push filter into place.

Ice bucket

Push in and pull open

Latch

Drop down tray (tray open)

*Select Models Only

Swing

Push \ Pull

About the controls with temperature settings.

PFE28,PYE22P Control Style A, LCD External Control

Control

Lock

Light

Temperature

Cubed

Water

Express Mode

Crushed

Settings

Precise Fill

Auto Fill

Cubed

GFE28, GFE26, DFE28, GYE22 Control Style B, External Control

Refrigerator

Hold 3 Sec for °F/°C

Recommended: 37 °F

Actual Set

Energy Smart

Recommended: 0°F

Freezer

Energy Smart Override

Hold 3 Seconds

Door Alarm

Ice Maker

GNE29, PWE23 Control Style C, Internal Control

Lock Controls

Hold 3 Seconds

Reset Filter

Hold 3 Seconds

NOTE: The refrigerator is shipped with protective film covering the temperature controls. If this film was not removed during installation, remove it now.

The temperature controls are preset in the factory at 37°F for the refrigerator compartment and 0°F for the freezer compartment. Allow 24 hours for the temperature to stabilize to the preset recommended settings.

The temperature controls can display both the SET temperature as well as the actual temperature in the refrigerator and freezer. The actual temperature may vary slightly from the SET temperature based on usage and operating environment.

About the controls with temperature settings. GEAppliances.com

Changing the Temperature for Control Style A

To Change the Refrigerator Temperature: Access By: Temperature Button Activate By: Below the word “Refrigerator”, use the arrows to

select the desired temperature. Press DONE when finished to return to HOME screen.

To Change the Freezer Temperature: Access By: Temperature Button Activate By: Below the word “Freezer”, use the arrows to

select the desired temperature. Press DONE when finished to return to HOME screen.

Temperature

Changing the Temperature for Control Style B

To change the temperature, press and release the Freezer

or Fridge pad. The display will show the set temperature. To change the temperature, press either the Freezer or Fridge pad until the desired temperature is displayed.

To turn OFF cooling system, access SETTINGS from the HOME screen. Page over and tap COOLING SYSTEM ON. Press DONE to return to HOME screen.

To turn ON cooling system, access SETTINGS from the HOME screen. Page over and tap COOLING SYSTEM OFF. Press DONE to return to HOME screen.

Turning the cooling system off stops the cooling to refrigerator, but it does not shut off the electrical power.

To turn OFF cooling system, press and hold Fridge and Ice Maker simultaneously for 3 seconds. When the cooling system is OFF the display should read OFF.

Changing Temp. for Control Style C

Temperature Display is located on inside of left-hand refrigerator door. To change the temperature, press and release the REFRIGERATOR or FREEZER pad. The ACTUAL TEMP light will come on and the display will show the actual temperature. To change the temperature, tap either the

REFRIGERATOR or FREEZER pad until the desired temperature is displayed.

To turn OFF cooling system, press and hold the REFRIGERATOR and FREEZER pads simultaneously for 3 seconds. When the cooling system is OFF the display should read OFF.

NOTE: For optimal temperature performance, we recommend to avoid placing food items directly at the air flow vents of the fresh food air tower and thus blocking the air flow.

To turn ON cooling system, press either REFRIGERATOR or FREEZER pad. The display will show the preset temperature settings of 37°F for refrigerator and 0°F for freezer. Turning the cooling system off stops the cooling to refrigerator, but it does not shut off the electrical power.

About the controls - features.

Control Style A, External Controls

Control

Lock

Light

Temperature

Cubed

Water

Express Mode

Crushed

Settings

Cubed

PFE28, PYE22P

Precise Fill

Auto Fill

Hands-free Autofill*

Hands-free Autofill uses sensors to monitor container height to automatically dispense filtered water without having to activate the paddle.

PreciseFill setting*

Precisely dispenses filtered water in accurate measurements in ounces, cups, quarts, or liters using paddle.

Refrigerator temp control

Adjust freezer compartment temperature.

Fresh food temp control

Adjust fresh food compartment temperature.

TurboFreeze™ setting

Activate TurboFreeze to quickly restore freezer temperatures after frequent door openings.

TurboCool™ setting

Activate TurboCool to quickly restore fresh food temperature after frequent door openings.

Lock controls

Press and hold 3 seconds to lock out ice and water dispenser and all feature and temperature buttons.

LED dispenser light

LED lighting that can be turned on/off to light your dispenser.

Door Alarm

Sounds to alert when the freezer or fresh food doors have been left open. Press and hold Door Alarm pad and it will toggle the sound between low, high and off.

Control Style B, External Controls

DFE28, GYE22

Photo upload*

GFE28, GFE26,

Insert USB memory stick to upload personal photos to the refrigerator LCD screen. LCD will provide on screen prompts to load and view slideshow. Make sure the photos are in the root directory in your USB.

Ice maker setting

Turn your ice makers on/off.

Cooling system On/Off

Press and hold Fridge & Ice Maker simultaneously for 3 seconds to turn the cooling system on or off.

USB Cover

Metric/English units

Press and hold Ice Maker & door alarm simultaneously for 3 seconds to switch between Metric & English units.

Additional settings:

• Photo upload and delete

• Slideshow

• Connected Home ready

• Reset water filter

• Ice maker on/off

• Door alarm

• Sound control

• Cooling system On/Off

• Metric/English units

• Auto fill video turorial

Additional Modes

• Sabbath Mode Press and hold lock & light simultaneously for 3 seconds to enter/ exit Sabbath mode. Activate Sabbath Mode to turn off interior lights, temperature control and advanced features. Compressor will run on a timed defrost when in Sabbath mode.

*Select Models Only

About the controls - features.* GEAppliances.com

Controls Style C, Internal Controls

Door Alarm

Sounds to alert when the freezer or fresh food doors have been left open.

Reset Filter*

Hold for 3 seconds after replacing filter.

Lock Controls

Press and hold 3 seconds to lock out ice and water dispenser and all feature and temperature buttons.

Refrigerator

Hold 3 Sec for °F/°C

Recommended: 37 °F

Actual Set

Energy Smart

Recommended: 0°F

Freezer

Energy Smart Override

Hold 3 Seconds

Door Alarm

Ice Maker

Lock Controls

Hold 3 Seconds

Reset Filter

Hold 3 Seconds

GNE29, PWE23

Freezer temp control

Adjust freezer compartment temperature

Refrigerator temp control

Adjust fresh food compartment temperature

Ice maker setting

Turn your ice makers on/off.

*Select Models Only

About the dispenser.*

Water & Ice Dispenser

(See About the controls with temperature settings & About the control features)

Precise

Fill

Auto ll Fi

ck o L

rol

t Con

Light

d e

Cub

ter

Dispenser tray

WARNING

Laceration Hazard

 Never put fingers or any other object into ice crusher

discharge opening. Doing so can result in contacting the ice crushing blades and lead to serious injury or amputation

 Use a sturdy glass when dispensing ice. A delicate glass may

break and result in personal injury.

If no water is dispensed when the refrigerator is first installed, there may be air in the water line system. Press the dispenser paddle for at least five minutes to remove trapped air from the water line and to fill the water system. To flush out impurities in the water line, throw away the first six full glasses of water.

To remove Dispenser Tray (Type A Only)



Pull Dispenser Tray out until it stops.



Locate tab in the center on the bottom and push up.



Pull Dispenser Tray assembly out.



Lift metal Dispenser Tray out at center notch to clean.

To remove Dispenser Tray (Type B Only)



Pull Dispenser Tray out.

To reinstall Dispenser Tray (Type A Only)



Place the Dispenser Tray cover on top of catch tray and

position under the two plastic retainers on either side.



Center Dispenser tray, and align with center guides.



Push in until it locks firmly in place.

To reinstall Dispenser Tray (Type B Only)



Center Dispenser Tray and push in until it snaps in place.

Important Facts About Your Dispenser



Do not add ice from trays or bags to the door ice maker

bucket. It may not crush or dispense.



Avoid overfilling glass with ice and use of narrow glasses.

Backed-up ice can jam the chute or cause the door in the chute to freeze shut. If ice is blocking the chute remove the ice bucket, poke it through with a wooden spoon.



Beverages and foods should not be quick-chilled in the

door ice maker bin. Cans, bottles or food packages in the storage drawer may cause the ice maker or auger to jam.

To Use the Internal Water Dispenser*

The water dispenser is located on the left wall inside the refrigerator compartment.

To dispense water:

Hold the glass against the recess. Push the water dispenser button. Hold the glass underneath the

dispenser for 2–3 seconds after releasing the dispenser button. Water may continue to dispense after the button is released.



To keep dispensed ice from missing the glass, put the glass

close to, but not touching, the dispenser opening.



Some crushed ice may be dispensed even though you

selected CUBED ICE. This happens occasionally when a few cubes accidentally get directed to the crusher.



After crushed ice is dispensed, some water may drip from the

chute.



Sometimes a small mound of snow will form on the door in the ice chute. This condition is normal and usually occurs when you have dispensed crushed ice repeatedly. The snow will eventually evaporate.

If no water is dispensed when the refrigerator is first installed, there may be air in the water line system. Press the dispenser button for at least 5 minutes to remove trapped air from the water line and to fill the water system. During this process, the dispenser noise may be loud as the air is purged from the water line system. To flush out impurities in the water line, throw away the first 6 glassfuls of water.

NOTE: To avoid water deposits, the dispenser should be cleaned periodically by wiping with a clean cloth or sponge.

*Select Models Only

About autofill.*

To Use HANDS FREE AUTO FILL:

• Center container on Recess Dispenser Tray and remove hand from container

• Press AUTO FILL

To Stop AUTO FILL

• Press CANCEL, to resume filling press AUTO FILL.

Important Facts about AUTO FILL

• For optimum results, use a uniform container between 4-8” tall and 2-6” wide.

• Container shape, fill level and functionality may vary on containers taller than 8”.

• Container volumes may vary, if error message “Container Not Found” is given, try a different container.

• AUTO FILL will time out.

• Handles and garnishes on the rim of the container my cause overfilling or variation in fill volumes.

• Splashing may occur depending on the location of the container, water flow rate, container shape, and ice cubes.

• Keep sensors clean with a clean damp cloth, and do not spray liquid or cleaners directly on sensors

• AUTO FILL works best with household water pressure of 60 to 100 psi.

GEAppliances.com

Sensors

*Select Models Only

About the GE® RPWFE water filter cartridge.

Water Filter Cartridge

The water filter cartridge is located in the fresh food interior on the left side wall, near the top.

This product uses radio frequency identification (RFID) to detect leaks and monitor filter status. The RFID technology is certified by the FCC.

FCCID: ZKJ-EBX1532P001 ICID: 10229A-EBX1532P001

“This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.”

“This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.”

When to replace the filter cartridge

The filter cartridge should be replaced every six months or earlier if 170 gallons of water has been dispensed or the flow of water to the dispenser or icemaker decreases.

Touch Screen Models: A filter status message will appear on the screen when the water filter needs to be replaced. The filter status will automatically update when the filter is replaced.

Non-touch Screen Models: A filter indicator light will illuminate on the screen when the water filter needs to be replaced.

Removing the filter cartridge

To replace the filter, first remove the old cartridge by opening the filter door and pulling on the bottom of the cartridge to allow it to swing outward. When the cartridge can no longer swing, gently pull to unseat it from the cartridge holder. DO NOT TWIST CARTRIDGE. A small amount of water may drip out.

Installing the Filter Cartridge

1. Align top of filter cartridge with cartridge holder with the word “FRONT” facing outward then push the cartridge toward the rear of the unit until it is fully seated. DO NOT TWIST THE FILTER CARTRIDGE!

2. While continuing to ensure cartridge is fully seated in the holder, gently swing the filter inward until it is in position. If filter will not swing easily, check to ensure filter is properly aligned and fully seated within the cartridge holder. Close the filter door.

Swing

Push \ Pull

3. Run two gallons of water through the cold water dispenser (about 5 minutes) to remove air from the system. A newly

installed filter cartridge will cause water to spurt from the dispenser. Use a large pitcher or sports bottle to catch the

water spray. DO NOT use hands-free auto-fill (some models) until all air is removed from the system.

4. Reset Filter Status message (non-touch screen models).

WARNING

Use of the hot water dispenser prior to purging air from the system may result in spurting of hot water and lead to hot water scalding. Follow the instructions above to purge all air from the system through the cold water dispenser prior to using the hot water dispenser.

Note: It is normal for water to appear discolored during the initial system flush. Water color will return to normal after first few minutes of dispensing.

Filter Bypass Plug

To reduce the risk of property damage due to water leakage, you MUST use the filter bypass plug when a replacement filter cartridge is not available. The dispenser and icemaker will not operate without either the filter or bypass plug installed. The bypass plug is installed in the same way as a filter cartridge.

*Select Models Only

Scalding Hazard.*

WARNING

To reduce the risk associated with choking, do not allow children under 3 years of age to have access to small parts during the installation of this product. The disposable filter cartridge should be replaced every 6 months at the rated capacity,

or sooner if a noticeable reduction in flow rate occurs. For the maximum benefit of your filtration system, GE recommends the use of GE-branded filters only. Using GE-branded filters

in GE and Hotpoint® refrigerators provides optimal performance and reliability. GE filters meet rigorous industry NSF standards for safety and quality that are important for products that are filtering your water. GE has not qualified non-GE-branded filters for use in GE and Hotpoint refrigerators and there is no assurance that non-GE-branded filters meet GE’s standards for quality, performance and reliability.

If you have questions, or to order additional filter cartridges, visit our website at www.geapplianceparts.com or call GE Parts and Accessories, 800.626.2002.

Customers in Canada should consult the yellow pages for the nearest Camco Service Center.

About the fresh food storage options.

Rearranging the Shelves

Shelves in the refrigerator compartment are adjustable.

To remove:

Remove all items from the shelf. Tilt the shelf up at the front. Lift the shelf up at the back and bring the

shelf out.

To replace:

While tilting the shelf up, insert the top hook at the back of the shelf in a slot on the track.

Lower the front of the shelf until the bottom of the shelf locks into place.

Spillproof Shelves

Spillproof shelves have special edges to help prevent spills from dripping to lower shelves.

Quick Space Shelf *

This shelf splits in half and slides under itself for storage of tall items on the shelf below.

This shelf can be removed and replaced or relocated (just like spillproof shelves).

NOTE: The location of the upper Quick Space Shelf is not adjustable.

*Select Models Only

About the fresh food storage options.

Non-Adjustable Dairy Bin*

To remove: Lift the dairy bin straight up, then pull out.

Adjustable Bins on the Door

Adjustable bins can easily be carried from refrigerator to work area.

To remove: Lift bin straight up, then pull out. To replace or relocate: Slide in the bin just

above the molded door supports, and push down. The bin will lock in place. See page 33.

Non-Dispense Models (Left Hand Door)

To replace: Engage the bin in the molded door supports and push down. The bin will lock in place. See page 33.

Drop down tray *

(tray open)

1. Open right fresh food door

2. Depress both buttons on lower sides of bin and bin will drop down.

3. Reverse to reinstall.

Non-Adjustable Bins on the Door (Dispenser Models - Left Hand Door)

To remove: Lift the bin straight up, then pull out. To replace: Engage the bin in the molded

supports on the door and push down. It will lock in place.

The ice maker door bins are not interchangeable, note the location upon removal and replace the bin in its proper location.

*Select Models Only

About the climate zone and

temperature controlled drawer. GEAppliances.com

ClimateZone

Keep fruits and vegetables organized in separate compartments for easy access.

Excess water that may accumulate in the bottom of the drawers or under the drawers should be wiped dry.

Fruits Vegetables

M E

ClimateZone

P R

O DU

Fruits Vege

CHE

ESE

C IT

R U

Note: Temperatures indicate the appropriate tem-

peratures for the food and actual temperatures may vary based on normal operation and other factors such as door openings and fresh food set point.

Temperature Controlled Drawer*

The Temperature Controlled Drawer is a full-width drawer with adjustable temperature control. This drawer can be used for large miscellaneous items.

To change setting, press select button.

Meat Beverage Deli

32° 34° 38°

CAUTION

Laceration Hazard.

Do not store glass bottles at this setting. If they are frozen, they can break and result in personal injury.

Select

*Select Models Only

About the climate zone and temperature controlled drawer.

How to Remove and Replace the Adjustable Deli/Produce Drawer

To remove:

Pull the drawer out to the stop position. Lift the front of the drawer up and out.

To replace:

Pull left and right slides until fully extended.

Place drawer back in first and rotate drawer front down to seat on slide.

Push the drawer in to closed position.

How to Remove and Replace Drawer Divider*

To remove:

Pull the drawer out to the stop position. Raise the front side of the divider

to unhook it from the rear wall of the drawer.

Divider

To replace:

Hook the back of the divider over the rear wall of the drawer.

Push the divider down.

*Select Models Only

About the freezer. GEAppliances.com

Freezer Basket and Drawer

Basket. Drawer

Ice Bucket *

Non-Adjustable Bin in the Freezer*

To remove: push in plastic tab on either left

or right side

To replace: slide bin into location until it locks into place.

Basket Removal

To remove, Standard Depth models only:

Open freezer door to the stop position. Remove freezer door bin by pushing

plastic tab on either left or right side to release bin hinge pin.

Remove freezer basket by lifting up the rear of the basket and moving basket rearward until the front of the basket can be rotated upward and out.

Lift it out to remove.

To remove, PYE and PWE models only:

Open fresh food doors. Open freezer door to the stop position.

Remove freezer basket by lifting up the rear of the basket and rotate it upward.

Lift it out to remove.

To replace:

Reverse step 1 thru 4 to replace.

*Select Models Only

About the automatic ice maker.

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

Ice maker

Feeler Arm

Automatic Ice Maker* The ice maker will produce seven cubes

per cycle approximately 100–130 cubes in a 24-hour period, depending on freezer compartment temperature, room temperature, number of door openings and other use conditions.

The ice maker will fill with water when it cools to 15°F (–10°C). A newly installed refrigerator may take 12 to 24 hours to begin making ice cubes.

If the refrigerator is operated before the water line connection is made to the unit or if the water supply to an operating refrigerator is turned off, make sure that the ice maker is turned off. Once the water has been connected to the refrigerator, the ice maker may be turned on. See the table below for details.

WARNING

You may hear a buzzing sound each time the ice maker fills with water.

Throw away the first few batches of ice to allow the water line to clear.

Be sure nothing interferes with the sweep of the feeler arm.

When the bin fills to the level of the feeler arm, the ice maker will stop producing ice. It is normal for several cubes to be joined together.

If ice is not used frequently, old ice cubes will become cloudy, taste stale and shrink.

NOTE: In homes with lower-than-average water pressure, you may hear the ice maker cycle multiple times when making one batch of ice.

To minimize the risk of personal injury, avoid contact with the moving parts of the ejector mechanism, or with the heating element that releases the cubes. Do not place fingers or hands on the automatic ice making mechanism while the refrigerator is plugged in.

How to Turn the Ice Maker On/Off

Display Type (See Page 6) Model # How to turn the ice maker on/off

Control Style A PFE28, PYE22P Use the settings menu on the touchscreen Control Style B GFE28/26, DFE28,

GYE22

Control Style C GNE29, PWE23 Use the “ICE MAKER” button on the control

Use the “ICE MAKER” button on the control

Lift and pull

Ice Box Door

Ice Bucket and Dispenser*

• Open the ice box door on inside of the left door.

• Pull up and out on on the ice bucket in the left hand door to remove it from the compartment .

• To replace the ice bucket, set it on the guide brackets and push until the ice bucket seats properly.

• If bucket cannot be replaced, rotate the ice bucket fork 1/4 turn clockwise.

Extra Ice Storage*

There is additional ice storage in the freezer compartment drawer.

• Open the freezer drawer.

• The ice bucket is located on the left side of the upper basket.

• Pull the upper basket forward to remove the ice bucket.

Freezer Ice Bucket

*Select Models Only

Care and cleaning of the refrigerator. GEAppliances.com

Cleaning the Outside

The stainless steel panels, door handles and trim.

Do not use appliance wax, polish, bleach, or other products containing chlorine on stainless steel. Stainless steel (on some models) can be cleaned with a commercially available stainless steel cleaner. A spray-on stainless steel cleaner works best.

Cleaning the Inside

To help prevent odors, leave an open box of baking soda in the refrigerator and freezer compartments.

Unplug the refrigerator before cleaning.

If this is not practical, wring excess moisture out of sponge or cloth when cleaning around switches, lights or controls. Use an appliance wax polish on the inside surface between the doors.

8VHZDUPZDWHUDQGEDNLQJVRGDVROXWLRQ³DERXWD

tablespoon (15 ml) of baking soda to a quart (1 liter) of water. This both cleans and neutralizes odors. Rinse and wipe dry.

Silver-accented plastic parts. Wash parts with soap or other mild detergents. Wipe clean with a sponge, damp cloth or paper towel. Do not use scouring pads, powdered cleaners, bleach or cleaners containing bleach because these products can scratch and weaken the paint finish.

Should spill tray need cleaning use lime remover.

CAUTION

Do not clean glass shelves or covers

with warm water when they are cold. Glass shelves and covers may break if exposed to sudden temperature changes or impact such as bumping or dropping. Tempered glass is designed to shatter into many small pieces if it breaks.

Behind the Refrigerator

Be careful when moving the refrigerator away from the wall. All types of floor coverings can be damaged, particularly cushioned coverings and those with embossed surfaces.

Raise the leveling legs located at the bottom front of the refrigerator.

Preparing for Vacation

For long vacations or absences, remove food and unplug the refrigerator. Clean the interior with a baking soda solution of one tablespoon (15 ml) of baking soda to one quart (1 liter) of water. Leave the doors open.

LCD Models: turn refrigerator off at control (pg 7) . If the temperature can drop below freezing, have a qualified

service technician drain the water supply system to prevent serious property damage due to flooding.

Preparing to Move

Secure all loose items such as shelves and drawers by taping them securely in place to prevent damage.

When using a hand truck to move the refrigerator, do not rest the front or back of the refrigerator against the hand truck. This could damage the refrigerator.

Pull the refrigerator straight out and return it to position by pushing it straight in. Moving the refrigerator in a side direction may result in damage to the floor covering or refrigerator.

Lower the leveling legs until they touch the floor.

When pushing the refrigerator back, make sure you don’t roll over the power cord or water supply line.

1) Turn refrigerator off (pg. 7) or unplug the refrigerator.

2) Empty ice bucket

3) Turn water supply off

If you cut the water supply off, turn off the ice maker (pg. 18).

Upon returning from vacation:

1) Replace the water filter.

2) Run 2 gallons of water through the cold water dispenser (about 5 minutes) to flush the system.

Handle only from the sides of the refrigerator.

Be sure the refrigerator stays in an upright position during moving.

Replacing the lights.

Refrigerator Lights (LEDs)

There is LED lighting in fresh food compartment and on the bottom of the fresh food doors to light the freezer compartment.*

An authorized technician will need to replace the LED light.

If this assembly needs to be replaced, call GE Service at 1.800.432.2737 in the United States or 1.800.561.3344 in Canada.

*Select Models Only

Installation

Refrigerator

Instructions

Questions? Call 800.GE.CARES (800.432.2737) or visit our Website at: GEAppliances.com In Canada, call 1.800.561.3344 or visit our Website at: www.GEAppliances.ca

GE and GE Profile™ models

BEFORE YOU BEGIN

Read these instructions completely and carefully.

WARNING

Built-in style models (model PYE, CYE, GYE, PWE, CWE, and ZWE) open. These models must be secured with the anti-tip floor bracket to prevent tipping forward, which could result in death or serious injury. Read and follow the entire installation instructions for installing the anti-tip floor bracket packed with your refrigerator.

•

IMPORTANT ³ Observe all governing codes and

ordinances. Save these instructions for local inspector’s use.

•

Note to Installer – Be sure to leave these instructions with

the Consumer.

• Note to Consumer – Keep these instructions for future reference.

• Skill level – Installation of this appliance requires basic mechanical skills.

• Completion time –

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not covered under the Warranty.

Tip Over Hazard.

are top heavy, especially with any doors

Refrigerator Installation can vary

Water Line Installation 30 minutes

TOOLS YOU MAY NEED

Adjustable Wrench

1/4” Outer Diameter

Compression Nut

and Ferrule (sleeve)

1/8”, 3/32”, 1/4” & 5/32”

Allen Wrenches

1/8” Drill Bit and Electric or Hand Drill

Ȓµ Socket Ratchet/Driver

Phillips-Head Screwdriver

Flat-Head Screwdriver

Tape Measure

PREPARATION

MOVING THE REFRIGERATOR INDOORS

If the refrigerator will not fit through a doorway, the refrigerator door and freezer drawer can be removed.

• To remove the refrigerator door, see the Installing the Refrigerator section.

• To remove the freezer drawer, see the Removing the Freezer Drawer section.

WATER SUPPLY TO THE ICE MAKER AND DISPENSER

If the refrigerator has an ice maker, it will have to be connected to a cold water line. A GE water supply kit (containing tubing, shutoff valve, fittings and instructions) is available at extra cost from your dealer, by visiting our website at GEAppliances.com (in Canada at www. GEAppliances.ca) or from Parts and Accessories, 800.626.2002 (in Canada 1.800.661.1616).

Pencil

Pliers

Torx T20, T25

1/4” Nut Driver

5/16” Nut Driver

Level

Installation Instructions

DIMENSIONS

ø8

”

All measurements are given with leveling leg fully retracted.

Standard Depth (SD) Models OnlyCounter Depth (CD) Models Only

353ø4”

69”

311ø4”

ø8

”

353ø4”

Overall Height to Top of Hinge Cover Height to Top of Cabinet Case Depth without Doors 29 Overall Exterior Case Width Overall Exterior Depth Doors/Drawers with Handles 36¼” 31¼”

69”

361ø4”

Case Depth w/o

” SD

ø8

” CD

ø8

Doors 29

23 1ø4” SD 18 1ø4” CD

Height from

floor to hinge

cover top 69

ø8”

Additional Dimensions

SD CD

ø8

”69

69” 69”

ø8

”24

353ø4”353ø4”

ø8

”

ø8

Moving THE REFRIGERATOR

• Using the chart below determine if the width of your passageway can accommodate the depth of the refrigerator. Ensure you have clearance to prevent damage to the refrigerator before safely moving it to the final location.

• If passageways are large enough to accommodate the refrigerator without removing the handles skip to Step 6. Leave tape, film and all packaging on doors until the refrigerator is in the final location.

• NOTE: Use a padded hand truck or moving straps to move this refrigerator. Place the refrigerator on the hand truck with a side against

the truck. We strongly recommend that two people move and complete this installation.

If your model number starts with PFE (SD)

If your model number starts with CFE (SD)

36.25” 35.25” 29.375”

33.75”

30.25”

If your model number starts with GFE, DFE, GNE (SD)

If your model number starts with CYE, PYE, PWE (CD)

31.25”

30.25”

28.75”29.75”

(PWE)

25.25”

24.375”

Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

• Do not install the refrigerator where the temperature will go below 60°F (16°C) because it will not run often enough to maintain proper temperatures.

• Do not install the refrigerator where the temperature will go above 100°F (37°C) because it will not perform properly.

• Install it on a floor strong enough to support it fully loaded.

CLEARANCES

Allow the following clearances for ease of installation, proper air circulation and plumbing and electrical connections.

Sides 1/8” (3 mm) Top 1” (25 mm) Cabinet/Hinge Cover Back 2” (50 mm)

REMOVE THE FRESH FOOD

DOOR HANDLE

Handle Design varies based on models, however Installation is same.

Stainless steel and plastic handles:

Loosen the set screws with the 1/8” Allen wrench

and remove the handle. NOTE: If the handle mounting fasteners need to be tightened or removed, use a 1/4” Allen wrench.

Mounting Fasteners

REMOVING THE REFRIGERATOR DOORS

• IMPORTANT NOTE: This refrigerator is 361/4” deep (311/4” for CD models). Doors and passageways leading to the installation location must be at least 36 leave the doors and handles attached to the refrigerator while transporting it into the installation location. If

passageways are less than 36

/4”, the refrigerator doors and handles can easily be scratched and damaged. The top cap and doors can be removed to allow the refrigerator to be safely moved indoors. If passageways

are less than 31

/4”, start with Step 1.

• If it is not necessary to remove doors, skip to Step

11. Leave tape and all packaging on doors until the refrigerator is in the final location.

• NOTE: Use a padded hand truck to move this refrigerator. Place the refrigerator on the hand truck with a side against the truck. We strongly recommend that TWO PEOPLE move and complete this installation.

/4” wide in order to

Leave film on until after installation

REMO VE T H E FREEZER DOOR HANDLE

Handle Design varies based on models, however Installation is same.

Stainless steel and plastic handles:

Loosen the set screws with the 1/8” Allen wrench and

remove the handle. NOTE: If the handle mounting fasteners need to be tightened or removed, use a 1/4” Allen wrench.

Mounting Fasteners

Leave film on until after installation

Reinstall the handles using the same procedure as removing.

Installation Instructions

INSTALLING THE REFRIGERATOR (cont.)

REMOVE THE REFRIGERATOR DOORS

3 3

Securely tape the door shut with masking tape or have

a second person support the door.

Start with left-hand door first: Remove the hinge cover

on top of the left refrigerator door by removing all hex screws and pulling it up. Do the same for the right-hand door and the middle cover.

REMOVE THE REFRIGERATOR DOORS (cont)

Disconnect the water line from the back of the unit by

pressing down on the dark grey collar while pulling up on the water line.

Pull water line through case conduit from the top to free the line for door removal. The water line is more than 4’ long and may need to be taped to Door for accessibility when reinstalling.

Hinge Cover

Disconnect both electrical connectors at the top cover.

Remove the 1/4” hex head screw to disconnect the ground wire from the hinge. Remove the 1/4” hex head screw to remove the strain relief from the water line.

Ground screw

Strain Relief

Y or Straight Connector

Using a 3/8” socket ratchet/driver, remove the screws securing the top hinge to the cabinet, then lift the hinge straight up to free the hinge pin from the location in the top of the door.

CAUTION

Single person lift could cause injury. Use assistance when handling, moving or lifting the refrigerator doors.

Note: when removing door, to prevent damage to door and electronics, carefully place the door in a proper location. Note: The lower door hinge pin and hinge are keyed and must be matched correctly for the door to self close properly. Please follow the directions carefully.

Lifting Hazard.

Installation Instructions

INSTALLING THE REFRIGERATOR (cont.)

REMOVE THE REFRIGERATOR DOORS (cont)

Note: for proper installation later, please follow the next step carefully.

Remove the tape and keeping the door as

straight as possible, open the door to 90º then lift straight up to remove it.

Lift up & off center hinge

Open Door to 90°

REMOVE OPPOSITE DOOR

Follow the same procedure on the opposite door. There are no wires or water lines on the opposite side

REMOVE CENTER HINGE (if necessary)

Remove the 3/8ļscrews securing the center hinge to the cabinet. Use T20 driver to remove outboard screw

REINSTALLING THE REFRIGERATOR DOORS

Reverse steps 1 through 4 to reinstall refrigerator, follow details below for critical alignments.

Reinstall center hinge first and torque the screws to 65

in-lbs. With the LH door at 90º to the front of the case, lower the refrigerator door onto the center hinge. Ensure that the door and hinge align correctly.

Rotate doors closed and make sure moveable center sealing

portion of the door aligns with the striker. If the door will not

self-close after reinstalling, remove door, turn door upside down, check alignment mark and arrow; (there is an alignment mark on the door closure mechanism. It corresponds to an alignment arrow on the plastic ring. Rotate door closure mechanism to align mark and arrow, reinstall door).

Align flats with tab.

Remove center screw

Loosen Outer screws

Underside OF Fresh Food Door

If door cannot be installed at 90° follow steps below:

Install door at 180° to case front.

2. If space limits opening door to less than 180°, then: a) Remove door, carefully turn door upside down. b) Check alignment of door closure mechanism shaft on underside of door. The flats on the shaft should correspond to alignment tab on plastic ring or mark on bottom end cap. c) If shaft is not aligned to tab/mark, using 5/32” Allen wrench, rotate door closure mechanism shaft counterclockwise for right door and clockwise for left door. Then align flat with tab/mark. d) Install the door at 90°.

Securely tape the door shut with masking tape or have a second person support the door. Reinstall the top hinge and torque the screws to 65 in-lbs.

Be sure to reinstall the ground wire and strain relief to the top

hinge.

Reinstall hinge cover. NOTE: Ensure wires are not pinched or

under screw bosses before tightening screws.

Installation Instructions

INSTALLING THE REFRIGERATOR (cont.)

REMOVE THE FREEZER DOOR

Pull the freezer door open to full extension. Remove 3 attachment screws, located at the bottom

on each side of the freezer door using 3/8” hex socket driver.

REPLACING THE FREEZER DOOR

Pull the slide Mechanism to full extension using both hands simultaneously.

Remove the basket resting on the slides.

CAUTION

Freezer door is heavy Use both hands to secure the door before lifting.

Lift the freezer door to disengage it from the slide

mechanism

Lifting Hazard

CAUTION

Freezer door is heavy Use both hands to secure the door before lifting.

Lift the freezer door and place it on the slide mechanism

Lifting Hazard

Align and insert tab on Freezer Door Bracket with slot on Freezer Slide Bracket.

The door can safely rest on the bottom. Do not rest the door on any other surfaces to avoid scratches.

Push the slide mechanism back completely until it self retracts.

Replace the attachment screws and torque the screws

to 65 in-lb For adjusting freezer door gaps, follow the instructions

on pg 27. Replace the basket

Installation Instructions

INSTALLING THE REFRIGERATOR (cont.)

Instructions for adjusting freezer door gaps:

IMPORTANT! The 6 mounting screws (3 on each side) are NOT interchangeable with the center or top hinge screws. Drawer screws have flat washer heads, and other screws have lines/ribs on washer heads.

After installation of the freezer door, check for uniform gaps (top and bottom of right and left hand side) with the template provided.

In the event of excessive gaps use the following steps to adjust the freezer door.

Step 1 - Loosen the 3 screws on each side (right and left) of the freezer door.

Step 2 - Adjust set screw clockwise if gap at the top is too big (see template). Turn the set screw using 3/32” hex

key clockwise by quarter to half a rotation Step 3 - Adjust set screw counter-clockwise if gap at the bottom is too big (see template). Turn the set screw

using 3/32” hex key counter-clockwise by quarter to half a rotation

Step 4 - Tighten the 3 screws on each side (right and left). Step 5 - Re-check the gaps using the template and repeat steps 1 to 4 if required and complete with step 5.

Fold here for using template

0.600”

Template for checking gaps. Gap should be 0.6” or below.

Gabarit pour vérifier les écarts. L’écart doit être de 0,6 po (1,5 cm) ou moins.

Plantilla para el control de espacios. El espacio debería ser de 0.6” o inferior.

Set Screw Vis d’ajustement Tornillo del Set

Plier ici pour utiliser le gabarit Dóblelo aquí para usar la plantilla

Step 2 Étape 2 Paso 2

Step 3 Étape 3 Paso 3

Step 1 Étape 1 Paso 1

Step 4 Étape 4 Paso 4

Refer to 239D4144P001, Pub No. 31-45474-2

Installation Instructions

INSTALLING THE REFRIGERATOR (cont.)

LEVEL THE FREEZER DOOR

LEVEL THE FREEZER DOOR (cont.)

Lift the door on the side requiring adjustment, rotate the cam to required position.

Locate the height adjuster cam in the freezer

door. Slightly loosen the three door attachment screws on both sides using a 3/8” hex socket driver.

Locate and loosen the cam screw using the T-27 screw driver.

0 - Initial position 1 - Lift by 0.050”

-1 - Lower by 0.050”

-2 - Lower by 0.100

-3 - Lower by 0.150”

After adjustment tighten the 3 attachment

screws using to 65 in-lb.

REMOVE PACKAGING

A) Remove all tape, foam and protective

packing from shelves and drawers.

Installation

Instructions

Anti-Tip Floor Bracket

PYE, CYE, GYE, PWE, CWE, and ZWE Models Only

WARNING

Tip Over Hazard.

NOTE:

If you did not receive an anti-tip bracket with your purchase, call 1.800.626.8774 to receive one at no cost. (In Canada, call 1.800.561.3344.) For installation instructions of the bracket, visit: www. GEAppliances.com. (In Canada, www.GEAppliances.ca.)

MATERIALS YOU MAY NEED (not included)

TOOLS YOU WILL NEED

1/8” (3 mm) Drill Bit and

Electric or Hand Drill

Pencil

LOCATING THE ANTI-TIP FLOOR

AT-2

Tape measure

5/16” (8 mm) Nut Driver

BRACKET

Place the anti-tip floor bracket locator template

(included inside the anti-tip kit) onto the floor up against the rear wall, within W, and in line with the desired location of the RH side of the refrigerator (see Figure 1).

Figure 1 – Installation Overview

Floor – Concrete (2 Holes)

Floor – Wood (2 Holes)

2 Wall Holes

Floor Bracket to Install

RH Holes

Lag Bolts 1/4” (6 mm) x 1-1/2” (38 mm)

Drill Bit Appropriate for Anchors

For Anti-Tip Bracket Mounted on CONCRETE Floors Only

AT-1

MEASURE CABINET OPENING

Anchor Sleeves

1/2” (12 mm) OD

AVAILABLE VS. REFRIGERATOR WIDTH

Measure width of cabinet opening where refrigerator will be placed, W.

Be sure to account for any countertop overhang, baseboard thickness and any clearance desired. Width, W, should not be less than 36”. The refrigerator will be placed approximately in the middle of this opening.

Rear Wall

REFRIGERATOR

Baseboard Thickness or Countertop Overhang (Whichever Is Larger) Plus Any Desired Clearance

15 ¼”

Rear RH Corner of

Base Bracket on the Refrigerator

Place the anti-tip floor bracket onto the locator

template with its RH floor holes lined up with the floor holes indicated on the template sheet, approximately 15 ¼” from the edge of the sheet or the RH side of the refrigerator.

Hold down in position and use the anti-tip floor

bracket as a template for marking the holes based upon your configuration and type of construction as shown in Step 3. Mark the hole locations with a pencil, nail or awl.

NOTE:

• It is REQUIRED to use at least 2 screws to mount the floor bracket (one on each side of the anti-tip floor bracket). Both must be into either the wall or the floor. Figure 2 indicates all the acceptable mounting configurations for screws. Identify the screw holes on the anti-tip floor bracket for your configuration.

RH Side of Refrigerator

Cabinet Wall

Locator Template Sheet

Front

RH Side

Refer to 239D1142P001, Pub No. 31-45484-3

Installation Instructions

LOCATING THE ANTI-TIP FLOOR

AT-2

BRACKET (cont.)

Figure 2 – Acceptable

Screw Placement Locations

Recommended Installation

Minimum Acceptable #1 –

AT-3

WOOD Wall and Floor Construction:

– Wood

Wall Plate Stud

Minimum Acceptable #3 –

Concrete Floor

ANTI-TIP BRACKET INSTALLATION

• Drill the appropriate number of 1/8” (3 mm) pilot holes in the center of each floor bracket hole being used (a nail or awl may be used if a drill is not available) AND remove the locator template from the floor.

• Mount the anti-tip floor bracket by fastening the 2, or recommended 4, #10-16 hex-head screws tightly into place as illustrated in Figure 3.

Figure 3 – Attachment to Wall and Floor

Rear RH

Corner of the

Refrigerator

Must Enter Metal Stud

Recommended Installation

Minimum Acceptable #2 –

2 Screws

Wood or

Floor

– Concrete

Wood Floor

Floor

Bracket

Wall

Plate

Stud

CONCRETE Wall and Floor Construction:

• Anchors required (not provided): 4 each 1/4” (6 mm) x 1-1/2” (38 mm) lag bolts 4 each 1/2” (12 mm) O.D. sleeve anchors

• Drill the recommended size holes for the anchors into the concrete at the center of the holes marked in Step 2.

• Install the sleeve anchors into the drilled holes. Place the anti-tip floor bracket as indicated in Step 2. Remove the locator template from the floor.

• Install the lag bolts through the anti-tip floor bracket and tighten appropriately.

WOOD Wall and TILE Floor Construction:

• For this special case, locate the 2 wall holes identified in Fig. 1. Drill an angled 1/8” (3 mm) pilot hole (approx. as shown in Fig. 3) in the center of each hole.

• Mount the anti-tip floor bracket using the Minimum Acceptable Installation #1, as illustrated in Fig. 2.

AT-4

POSITIONING THE REFRIGERATOR TO ENGAGE THE ANTI-TIP FLOOR AND BASE BRACKETS

Before pushing the refrigerator into the opening,

plug the power cord into the receptacle and connect waterline (if equipped). Check for leaks.

Locate the refrigerator’s RH side and move back

approximately in line with the RH side of the cabinet opening, W. This should position the anti-tip floor bracket to engage the anti-tip base bracket on the refrigerator.

Gently roll the refrigerator back into the cabinet

opening until it comes to a complete stop. Check to see if the refrigerator front lines up with the cabinet front face. If not, carefully rock the refrigerator forward and backward until engagement occurs and you notice that the refrigerator is fully pushed up against the rear wall.

If Applicable: Adjust the rear (and front) wheel

height settings to fully engage the rear anti-tip brackets, while also aligning the refrigerator front with the cabinet front face.

NOTE:

If you pull the refrigerator out and away from the wall for any reason, make sure the anti-tip floor bracket is engaged when the refrigerator is pushed back against the rear wall.

Refer to 239D1142P001, Pub No. 31-45484-3

+ 106 hidden pages