GE APPLIANCES AGE21DH User Manual

Air Conditioners

Safety Instructions . . . . . . . . .2, 3

Operating Instructions

. . . . . . .4, 5

Care and Cleaning . . . . . . . . . . .6

Installation Instructions

Preparing to Install the

Air Conditioner . . . . . . . . . . . . . .7

Window Installation . . . . . . . .8–12

Troubleshooting Tips . . . . .13–15

Normal Operating Sounds . . . . .15

Consumer Support

Consumer Support . . . .Back Cover

Product Registration . . . . . . .17, 18

Warranty . . . . . . . . . . . . . . . . . . .19

3828A20514N 49-7508-1 03-05 JR

Owner’s Manual and

Installation Instructions

www.GEAppliances.com

Write the model and serial numbers here:

Model # __________________________

Serial # __________________________

Find these numbers on a label on the
side of the air conditioner.

Room

AGE14
AGE18
AGE21

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

2

IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of fire, electric shock
or personal injury.

■ Use this appliance only for its intended

purpose as described in this Owner’s
Manual.

■ This air conditioner must be properly

installed in accordance with the Installation
Instructions before it is used.

■ Never unplug your air conditioner by

pulling on the power cord. Always grip
plug firmly and pull straight out from the
receptacle.

■ Replace immediately all electric service

cords that have become frayed or otherwise
damaged. Do not use a cord that shows
cracks or abrasion damage along its length
or at either the plug or connector end.

■ Turn the mode control to OFF and unplug

your air conditioner before making any
repairs or cleaning.

NOTE: We strongly recommend that any
servicing be performed by a qualified
individual.

■ For your safety…do not store or use

combustible materials, gasoline or other
flammable vapors or liquids in the vicinity
of this or any other appliance.

■ All air conditioners contain refrigerants,

which under federal law must be removed
prior to product disposal. If you are getting
rid of an old product with refrigerants, check
with the company handling disposal about
what to do.

SAFETY PRECAUTIONS

Do not, under any circumstances, cut or remove
the third (ground) prong from the power cord. For
personal safety, this appliance must be properly
grounded.

The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding) wall
outlet to minimize the possibility of electric
shock hazard from this appliance.

Power cord includes a current interrupter
device. A test and reset button is provided on
the plug case. The device should be tested on a
periodic basis by first pressing the TEST button
and then the RESET button. If the TEST button
does not trip or if the RESET button will not
stay engaged, discontinue use of the air
conditioner and contact a qualified
service technician.

Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.

Where a 2-prong wall outlet is encountered,
it is your personal responsibility and obligation
to have it replaced with a properly grounded
3-prong wall outlet.

The air conditioner should always be
plugged into its own individual electrical
outlet which has a voltage rating that matches
the rating plate.

This provides the best performance and also
prevents overloading house wiring circuits
which could cause a fire hazard from
overheated wires.

See the Installation Instructions, Electrical
Requirements section for specific electrical
connection requirements.

HOW TO CONNECT ELECTRICITY

3

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

WARNING!

Because of potential safety hazards under certain
conditions, we strongly recommend against the
use of an extension cord.

However, if you must use an extension cord,
it is absolutely necessary that it be a UL-listed,
14 gauge, 3-wire grounding type appliance
extension cord having a grounding type plug
and outlet and that the electrical rating of the
cord be 15 amperes (minimum) and 125 volts.

CAUTION: DO NOT use an extension

cord with any of the 230/208 volt models.

USE OF EXTENSION CORDS–115-Volt models only

Because of potential safety hazards under certain
conditions, we strongly recommend against the use
of an adapter plug.

However, if you must use an adapter, where
local codes permit, a temporary connection may
be made to a properly grounded 2-prong wall
outlet by use of a UL-listed adapter available
at most local hardware stores.

The larger slot in the adapter must be aligned
with the larger slot in the wall outlet to provide
proper polarity in the connection of the
power cord.

When disconnecting the power cord from the
adapter, always hold the adapter in place with
one hand while pulling the power cord plug
with the other hand. If this is not done, the
adapter ground terminal is very likely to break
with repeated use.

If the adapter ground terminal breaks, DO NOT
USE the air conditioner until a proper ground
has been established.

Attaching the adapter ground terminal to a wall outlet
cover screw does not ground the appliance unless the
cover screw is metal, and not insulated, and the wall
outlet is grounded through the house wiring. You should
have the circuit checked by a qualified electrician to
make sure the outlet is properly grounded.

USE OF ADAPTER PLUGS–

115-Volt models only

www.GEAppliances.com

SAVE THESE INSTRUCTIONS

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

4

About the controls on the air conditioner.

Features and appearance will vary.

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

MODE CONTROLTEMP CONTROL

W

A

R

M

E

R

C

O

O

L

E

R

Temp Control

The temp control is used to maintain the
room temperature. The compressor will
cycle on and off to keep the room at the
same level of comfort. Turn the knob
clockwise to COOLER (blue) and the
indoor air will become cooler. Turn the
knob counterclockwise to WARMER (red)
and the indoor air will become warmer.

Mode Control

HIGH COOL and LOW COOL provide cooling

with different fan speeds.

HIGH HEAT and LOW HEAT provide heating
with different fan speeds.

FAN settings provide air circulation and
filtering without cooling or heating.

NOTE: If you move the mode control from a
cool setting to OFF, a fan setting, or a heat
setting wait at least 3 minutes before switching
back to a cool setting.

Cooling Descriptions

For Normal Cooling—Select HIGH COOL or
LOW COOL with the temp control at

midpoint.

For Maximum Cooling—Select HIGH COOL
with the temp control turned clockwise
as far as possible.

For Quieter & Nighttime Cooling—Select
LOW COOL with the temp control at

midpoint.

Heating Descriptions

For Normal Heating—Select HIGH HEAT or
LOW HEAT with the temp control at

midpoint.

For Maximum Heating—Select HIGH HEAT
with the temp control turned counter­clockwise as far as possible.

For Quieter & Nighttime Heating—Select
LOW HEAT with the temp control at

midpoint.

Controls

LOW
COOL

Air Direction—Side-to-Side

CIRCULAIRE (on some models)

For fixed side-to-side air direction, set the
Circulaire switch to ON until the desired air
direction is obtained, then move it to OFF.

For continuous side-to-side air circulation
(cool settings only), set the Circulaire
switch to ON.

5

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Vent Control

The vent control is located above the
control knobs.

When set at CLOSE, only the air inside the room
will be circulated and conditioned. When set
at OPEN, some inside air is exhausted outside.

To open the vent, pull the lever toward you.
To close it, push it in.

www.GEAppliances.com

Additional controls and important information.

Air Direction—Up and Down

Fingertip pressure on the bank of horizontal
louvers adjusts the air direction up or down.

Care and cleaning of the air conditioner.

6

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

Outdoor Coils

The coils on the outdoor side of the air
conditioner should be checked regularly.
If they are clogged with dirt or soot they
may be professionally cleaned.

Grille and Case

Turn the air conditioner off and remove the
plug from the wall outlet before cleaning.

To clean, use water and a mild detergent.
Do not use bleach or abrasives.

Air Filter

The air filter behind the front grille should be
checked and cleaned at least every 30 days or
more often if necessary.

To remove (on some models):

Open the inlet grille upward by pulling
out the bottom of the inlet grille.

Using the tab, pull up slightly on the
filter to release it and pull it down.

Clean the filter with warm, soapy water. Rinse
and let the filter dry before replacing it.

CAUTION: DO NOT operate the air

conditioner without a filter because dirt and lint will
clog it and reduce performance.

To remove (on some models):

Open the inlet grille downward by pulling
out the top of the inlet grille.

Using the tab, push down slightly on the
filter to release it and pull it up.

2

1

2

1

BEFORE YOU BEGIN

Read these instructions completely
and carefully.

•

IMPORTANT — Save these

instructions for local inspector’s use.

•

IMPORTANT — Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these
instructions with the Consumer.

• Note to Consumer – Keep these
instructions for future reference.

• Skill level – Installation of this appliance
requires basic mechanical skills.

• Completion time – Approximately 1 hour

• We recommend that two people install

this product.

• Proper installation is the responsibility
of the installer.

• Product failure due to improper installation
is not covered under the Warranty.

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: www.GEAppliances.com

Installation

Air Conditioner

Instructions

Some models require a 115/120-volt a.c.,
60 Hz grounded outlet protected with a
15-amp time delay fuse or circuit breaker.

The 3-prong grounding plug minimizes the
possibility of electric shock hazard. If the wall
outlet you plan to use is only a 2-prong outlet,
it is your responsibility to have it replaced with
a properly grounded 3-prong wall outlet.

Some models require 230/208-volt a.c.,
protected with a time delay fuse or circuit
breaker. These models should be installed
on their own single branch circuit for
best performance and to prevent
overloading house or apartment wiring
circuits, which could cause a possible
fire hazard from overheating wires.

ELECTRICAL REQUIREMENTS

TOOLS YOU WILL NEED

Phillips head screwdriver

Ruler or tape measurePencil

Level

Scissors or knife

CAUTION:

Do not, under any circumstances, cut or
remove the third (ground) prong from the
power cord.

Do not change the plug on the power cord
of this air conditioner.

Aluminum house wiring may present special
problems—consult a qualified electrician.

7

Flat-blade screwdriver

Power cord includes a current interrupter
device. A test and reset button is provided on
the plug case. The device should be tested on a
periodic basis by first pressing the TEST button
and then the RESET button. If the TEST button
does not trip or if the RESET button will not stay
engaged, discontinue use of the air conditioner
and contact a qualified service technician.

Type A (14)

Support bracket (2)

Sill bracket (2)

Type B (7) Type C (5) Type D (2) Carriage Bolt (2) Lock Nut (4)

Window locking

bracket

Frame guide (2)

Top

mounting

rail

Top mounting

rail seal strip

Right

accordion

panel

Foam top

window gasket

Window

sash seal

Left

accordion

panel

PARTS INCLUDED

(Appearance may vary)

Installation Instructions

8

Installation Instructions

WINDOW REQUIREMENTS

• These instructions are for a standard
double-hung window. You will need to
modify them for other types of windows.

• The air conditioner can be installed
without the accordion panels if needed
to fit in a narrow window. See the
window opening dimensions.

• All supporting parts must be secured
to firm wood, masonry or metal.

• The electrical outlet must be within
reach of the power cord.

1

STORM WINDOW REQUIREMENTS

A storm window frame will not allow the
air conditioner to tilt toward the outside,
and will keep it from draining properly.
To adjust for this, attach a piece of wood
to the stool.

WOOD PIECES–
WIDTH: 2″
LENGTH: Long enough to fit inside the

window frame.
THICKNESS: To determine the thickness,

place a piece of wood on the stool to
make it 1/2″ higher than the top of the
storm window frame.

Attach securely with nails or screws
provided by the installer.

1/2″ higher
than frame

Storm
window
frame

Wood

Stool

2

9

18″ min.

29″ to 41″

(With accordion panels)

261⁄4″ min.

(Without accordion panels)

REMOVE THE AIR CONDITIONER
FROM THE CASE

Remove the 2 shipping screws from the
back of the case.

Remove the 2 screws on each side of the
case. Keep these for later use.

Slide the air conditioner from the case by
gripping the base pan handle and pulling
forward while bracing the case.

C

B

A

3

Shipping screws

PREPARE THE WINDOW AND
THE CASE (CONT.)

Carefully insert the plastic frame guides
into the bottom of the case on each side.

Remove the backing from the top mounting
rail seal strip and attach it to the bottom of
the top mounting rail.

Install the top mounting rail with 3 type A
screws on the inside of the case. Insert the
frames for the accordion panels into the top
mounting rail and the frame guides. Attach
the accordion panels to the side of the case
using 5 type A screws on each side.

D

C

B

4

Installation Instructions

PREPARE THE WINDOW AND
THE CASE

Cut the window sash seal to the proper
length. Peel off the backing and attach the
seal to the underside of the window sash.

A

4

Bottom of case

Frame guide

10

Top mounting rail

Frame guides

INSTALL THE CASE IN THE
WINDOW

Align the inside edge of the sill brackets
with the 11″ marks from the centerline and
attach them to the window sill using 2 type
B screws on each side.

Carefully place the case on the window
stool aligning the center front on the
bottom with the centerline marked on the
window stool. Close the window making
sure the window sash is behind the top
mounting rail.

Using the larger diameter hole in the case,
attach

the brackets to the case using two

type D screws and 2 lock nuts on each side.

C

B

A

6

Installation Instructions

INSTALL THE CASE IN THE
WINDOW (CONT.)

Adjust the carriage bolts and the lock nuts
in each support so that the case is installed
with a slight tilt to the outside. Use a level;
about 1/3 bubble will be the correct case
slant to the outside. Tighten the bolts.

CAUTION: DO NOT drill a hole in the base pan.
The unit is designed to operate with
approximately 1/2 ″ of water in the base pan.

Secure the case to the window stool by
using 3 type B screws.

Pull the accordion panels to each window
sash track. Attach them on each side to the
window sash and the window stool using
4 type C screws.

F

E

D

PREPARE THE WINDOW

Loosely attach the sill brackets to the
support brackets using the 2 carriage bolts
and 2 lock nuts.

Open the window and mark the centerline
of the window stool. Measure and mark 11″
to the left and right of the centerline.

B

A

5

Sill bracket

Lock nut

Support bracket
Carriage
bolt

Centerline

11″

11″

11

6

INSTALL THE AIR CONDITIONER
IN THE CASE

Slide the air conditioner into the case.
Reinstall the 2 screws removed earlier on
each side of the case.

Before installing the front grille, pull out the
vent control lever located above the unit
control knobs, as shown.

Attach the front grille to the case by inserting
the tabs on the grille into the slots on the
front of the case. Push the grille in until it
snaps into place.

Lift the inlet grille and secure the front
frame with a type A screw through the
front grille. Lower the inlet grille back into
place.

D

C

B

A

Installation Instructions

INSTALL A SUPPORT BRACKET
AND THE FOAM TOP WINDOW
GASKET

Attach a support bracket with a Type C
screw.

Cut the foam top window gasket to the
window width.

Stuff the foam between the glass and the
window to prevent air and insects from
getting into the room.

C

B

A

7 8

Guide the lever carefully
through the grille as you
push it in.

12

Consumer SupportTroubleshooting TipsOperating Instructions

Safety Instructions

Installation Instructions

13

Problem Possible Causes What To Do

Air conditioner The air conditioner • Make sure the air conditioner plug is pushed completely
does not start is unplugged into the outlet.

The fuse is blown/circuit • Check the house fuse/circuit breaker box and replace
breaker is tripped the fuse or reset the breaker.

Power failure • If power failure occurs, turn the air conditioner OFF.

When power is restored, wait 3 minutes to restart the
air conditioner to prevent tripping of the compressor
overload.

The current interrupter • Press the RESET button located on the power cord plug.
device is tripped

• If the RESET button will not stay engaged, discontinue

use of the air conditioner and contact a qualified service
technician.

Air conditioner Ice blocks the air flow • Set the mode control at FAN or HIGH COOL with the
freezing up and stops the air conditioner temp control at a warmer setting.

from cooling the room

Air conditioner does not Airflow is restricted • Make sure there are no curtains, blinds or furniture
cool as it should blocking the front of the air conditioner.

The temp control may • Turn the temperature knob clockwise as far as possible.
not be set correctly

The air filter is dirty • Clean the filter at least every 30 days. See the Operating

Instructions section.

The room may have been hot • When the air conditioner is first turned on you need

to allow time for the room to cool down.

Cold air is escaping • Check for open furnace floor registers and

cold air returns.

• Set the air conditioner’s vent to the closed position.

Cooling coils have iced up • See “Air conditioner freezing up” below.

Air conditioner does not Airflow is restricted • Make sure there are no curtains, blinds or furniture
warm as it should blocking the front of the air conditioner.

The temp control may • Turn the knob counterclockwise as far as possible.
not be set low enough The lowest setting provides maximum warming.

The air filter is dirty • Clean the filter at least every 30 days. See the Operating

Instructions section.

The room may have been cold •When the air conditioner is first turned on, you need to

allow time for the room to warm up.

Warm air is escaping • Check for open furnace floor registers and

cold air returns.

Troubleshooting Tips
Save time and money! Review the chart below first

and you may not need to call for service.

Before you call for service…

www.GEAppliances.com

14

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

Problem Possible Causes What To Do

Water drips outside Excessively hot and • This is normal.

humid weather

Water drips indoors The air conditioner is not • For proper water disposal, make sure the air conditioner

tilted to the outside slants slightly from the case front to the rear.

Water collects in Moisture is removed from • This is normal for a short period in areas with
base pan indoor air and drains into little humidity; normal for a longer period in very

rear of a cabinet where a fan humid areas.
blows it against the outdoor
condenser coil

Troubleshooting Tips

Before you call for service…

15

www.GEAppliances.com

Normal Operating Sounds

■ You may hear a pinging noise caused by

water being picked up and thrown against
the condenser on rainy days or when the
humidity is high. This design feature helps
remove moisture and improve efficiency.

■ You may hear the thermostat click when

the compressor cycles on and off.

■ Water will collect in the base pan during

high humidity or on rainy days. The water
may overflow and drip from the outdoor
side of the unit.

■ The fan may run even when the compressor

does not.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

16

Notes.

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

General Electric Company

Warranty Registration Department
P.O. Box 32150
Louisville, KY 40232-2150

Please place in envelope and mail to:

✁

Cut here

17

GE Service Protection Plus

™

GE, a name recognized worldwide for quality and dependability, offers you
Service Protection Plus

™

—comprehensive protection on all your appliances—

No Matter What Brand!

Benefits Include:

• Backed by GE

• All brands covered

• Unlimited service calls

• All parts and labor costs included

• No out-of-pocket expenses

• No hidden deductibles

• One 800 number to call

You will be completely satisfied with our service protection or you may request your money back
on the remaining value of your contract. No questions asked. It’s that simple.

Protect your refrigerator, dishwasher, washer and dryer, range, TV, VCR and much more—any brand!
Plus there’s no extra charge for emergency service and low monthly financing is available. Even icemaker
coverage and food spoilage protection is offered. You can rest easy, knowing that all your valuable
household products are protected against expensive repairs.

Place your confidence in GE and call us in the U.S. toll-free at 800.626.2224
for more information.

*All brands covered, up to 20 years old, in the continental U.S.

We’ll Cover Any Appliance.
Anywhere. Anytime.*

18

Consumer Product Ownership Registration

Important

Mail
Today!

GE Appliances

GE Consumer & Industrial
Louisville, Kentucky
www.GEAppliances.com

First

Name

Mr. ■■ Ms. ■■ Mrs. ■■ Miss ■■

Street

Address

City

State

Date Placed

In Use

Month

Day

Year

Zip

Code

Apt. #

Last

Name

Phone

Number

_

_

Consumer Product Ownership Registration

Dear Customer:
Thank you for purchasing our product and thank you for placing your confidence in us.
We are proud to have you as a customer!

Follow these three steps to protect your new appliance investment:

Important: If you did not get a registration card with your

product, detach and return the form below to
ensure that your product is registered, or register
online at www.GEAppliances.com.

1

23

Model Number Serial Number

✁

Cut here

Complete and mail
your Consumer
Product Ownership
Registration today.

Have the peace of
mind of knowing we
can contact you in
the unlikely event of

a

safety modification.

After mailing the
registration below,
store this document
in a safe place. It
contains information
you will need should
you require service.
Our service number is

800.GE.CARES
(800.432.2737).

Read your Owner’s
Manual carefully.
It will help you
operate your new
appliance properly.

Model Number Serial Number

E-mail Address*

* Please provide your e-mail address to receive, via e-mail, discounts, special offers and other important

communications from GE Appliances (GEA).

■■ Check here if you do not want to receive communications from GEA’s carefully selected partners.

FAILURE TO COMPLETE AND RETURN THIS CARD DOES NOT DIMINISH YOUR
WARRANTY RIGHTS.

For information about GEA’s privacy and data usage policy, go to www.GEAppliances.com and click
on “Privacy Policy” or call 800.626.2224.

19

Consumer SupportTroubleshooting TipsOperating Instructions

Safety Instructions

Installation Instructions

Air Conditioner Warranty.

For The Period Of: We Will Replace:

One Year Any part of the air conditioner which fails due to a defect in materials or workmanship.

From the date of the During this full one-year warranty, we will also provide, free of charge, all labor and in-home
original purchase service to replace the defective part.

Five Years Any part of the sealed refrigerating system (the compressor, condenser, evaporator and

From the date of the all connecting tubing) which fails due to a defect in materials or workmanship. During this
original purchase four-year additional warranty, we will also provide, free of charge, all labor and in-home service

to replace the defective part.

■ Service trips to your home to teach you how to

use the product.

■ Improper installation, delivery or maintenance. If you

have an installation problem, or if the air conditioner
is of improper cooling capacity for the intended use,
contact your dealer or installer. You are responsible
for providing adequate electrical connecting facilities.

■ Failure of the product resulting from modifications to

the product or due to unreasonable use including failure
to provide reasonable and necessary maintenance.

■ In commercial locations labor necessary to move the

unit to a location where it is accessible for service
by an individual technician.

■ Replacement of house fuses or resetting of circuit

breakers.

■ Failure due to corrosion on models not corrosion-

protected.

■ Damage to the product caused by improper power supply

voltage, accident, fire, floods or acts of God.

■ Incidental or consequential damage caused by possible

defects with this air conditioner.

■ Damage caused after delivery.

What Is Not Covered:

This warranty is extended to the original purchaser and any succeeding owner for products purchased for home
use within the USA. In Alaska, the warranty excludes the cost of shipping or service calls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state. To know what your
legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.

Warrantor: General Electric Company. Louisville, KY 40225

All warranty service provided by our Factory Service Centers,
or an authorized Customer Care

®

technician. To schedule service,

on-line, 24 hours a day, visit us at GEAppliances.com, or call

800.GE.CARES (800.432.2737).

Staple your receipt here.

Proof of the original purchase

date is needed to obtain service

under the warranty.

Printed in Korea

GE Appliances Website www.GEAppliances.com

Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day,
any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals,
order parts, catalogs, or even schedule service on-line. You can also “Ask Our Team of Experts™”
your questions, and so much more...

Schedule Service www.GEAppliances.com

Expert GE repair service is only one step away from your door. Get on-line and schedule your service at
your convenience 24 hours any day of the year! Or call 800.GE.CARES (800.432.2737) during normal
business hours.

Real Life Design Studio www.GEAppliances.com

GE supports the Universal Design concept—products, services and environments that can be used by
people of all ages, sizes and capabilities. We recognize the need to design for a wide range of physical and
mental abilities and impairments. For details of GE’s Universal Design applications, including kitchen
design ideas for people with disabilities, check out our Website today. For the hearing impaired, please call

800.TDD.GEAC (800.833.4322).

Extended Warranties www.GEAppliances.com

Purchase a GE extended warranty and learn about special discounts that are available while your warranty
is still in effect. You can purchase it on-line anytime, or call 800.626.2224 during normal business hours.
GE Consumer Home Services will still be there after your warranty expires.

Parts and Accessories www.GEAppliances.com

Individuals qualified to service their own appliances can have parts or accessories sent directly to their
homes (VISA, MasterCard and Discover cards are accepted). Order on-line today, 24 hours every day or
by phone at 800.626.2002 during normal business hours.

Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally
should be referred to qualified service personnel. Caution must be exercised, since improper servicing may cause
unsafe operation.

Contact Us www.GEAppliances.com

If you are not satisfied with the service you receive from GE, contact us on our Website with all the details
including your phone number, or write to: General Manager, Customer Relations

GE Appliances, Appliance Park
Louisville, KY 40225

Register Your Appliance www.GEAppliances.com

Register your new appliance on-line—at your convenience! Timely product registration will allow for
enhanced communication and prompt service under the terms of your warranty, should the need arise.
You may also mail in the pre-printed registration card included in the packing material.

Consumer Support.