GEAppliances 18, 24, 21 Use And Care Manual

Contents

Appliance Registration

2

Location

Automatic Icemaker

9 Moving & Vacation Tips

;;

UseandCareof

Base Grille

13 Water Supply to Icemaker 13

Top-Mount

Care and Cleaning

10-12

Problem Solver 20,21

Consumer Services

23

Normal Operating Sounds 20

No-Frost

Energy-Saving Tips

2

Safety Instructions 3

18,21

Food Storage Suggestions

6

Shelves

7

Storage Times

6

Storage Drawers 8

and24

Ice Service

8 Drawer&CoverRemoval 11, 12

Installation

14 Temperature Controls 4,5

Models

Adapter Plug

14 Warranty Back Cover

Electrical Requirements 14

Water Filter Accessory 9

Extension Cord

14 Whter Line Installation 18, 19

Grounding 14

Light Bulb Replacement

12 How to Reverse the

Model and Serial Numbers 2

Door Swing

15-17

Power Saver Switch

4

Preparation

13

Adjustable Rollers

13

GE Answer Center@

Clearances 13

800.626.2000

.. . . . ..——-

3w#F?

..

\

HELP US HELP YOU...

1

.

Read this book carefully.

It is intended to help you operate and maintain your
new refrigerator properly.

Keep it handy for answers to your questions.
If you don’t understand something or need more help,

write (include your phone number):

Consumer Affairs
Appliance Park
Louisville, KY 40225

If you received a damaged refrigerator...

Immediately contact the dealer (or builder) that sold
you the refrigerator.

Save time and money.
Before you request service...

Check the Problem Solver in the back of the book.
It lists minor opemting problems that you can
correct yourself.

Write down the model & serial numbers.

You’ll see them on a label on the left side, near the top
of the fresh food compartment.

These numbers are also on the Consumer Product
Ownership Registration Card that came with your
refrigerator.

Before sending in the registration card, please write
these numbers here:

Model Number

Serial Number

Use these model and serial numbersin any
correspondenceor service calls concerning your
refrigerator.

}

ENERGY-SA~G TIPS

●

4

‘CLocation of your refrigerator is important. Avoid

locating it next to your range, a heating vent or
where the sun will shine directly on it.

● Close the doors as soon as possible, particularly in

hot, humid weather.

● Keep Power Saver Switch in the power saver

position unless moisture forms on the outside
of the refrigerator.

cBe sure the doors are closed tightly. Before leaving

the house or retiring for the night, check to be sure
the doors haven’t been left open accidentally.

..

cKeep foods covered to reduce moisture buildup

inside the refrigerator.

IF YOU NEED SERVICE I

To obtain service, see the Consumer Services page in
the back of this book.

We’re proud of our service and want you to be
pleased. If for some reason you are not happy with the
service you receive, here are three steps to follow for
further help.

FIRST, contact the people who serviced your
appliance. Explain why you are not pleased. In most “
cases this will solve the problem.

NEXT, if you are still not pleased, write all the

I

details—including your phone number—to:

I

Manager, Consumer Relations

I

Appliance Park

I

Louisville, KY 40225

FINALLY, if your problem is still not resolved, write:

,

Major Appliance
Consumer Action Panel
20 North Wacker Drive
Chicago, IL 60606

,1

~

.

IMPORTANT SAFETY INSTRUCTIONS

e

Read all instructionsbefore using this appliance.

A

WARNING-When using this ‘
appliance, always exercise basic safe& .
precautions, including the following:

I

● Use this appliance only forits intendedpurpose

as described in this Use and Care Guide.

●

a

(,

● This refrigerator must be properly

‘Qb:Q

~

a

instded andlocated in accordance

---*

withtheInstallationInstructions

beforeit is used.See

grounding instructions

,

!

below and in the Installation section.

~Never unplug your refrigerator by

pulling onthepowercord.Always

grip plug fdy and pull straight out

from the outlet.

oRepair or replace immediately all electric

service cords that have become frayed or
otherwise damaged. Do not use a cord that

shows cracks or abrasion damage along its
Iength or at either the plug or connector end.

o

● When moving your refrigerator away from

the wall, be careful not to roll over or damage
the power cord.

s Do not allow children to climb, stand or

hang on the shelves in the refrigerator.They

could damage the refrigerator and seriously
injure themselves.

● ~ Yom old refrigerator is stillaround

the house but not in use, be sure to
remove the doors.This will reduce the

possibility of danger to children.

● After your refrigerator is in operation,

do not touch the cold surfaces in the freezer

I

compartment particularly when hands are
damp or weL Skin may adhere to these

extremely cold surfaces.

● If your refrigerator has an automatic icemaker,

avoid contact with the moving parts of the
ejector mechanism, or with the heating element

J

that releases the cubes. Do not place fingers or

. Don’t r&@ezefrozen

foodswhich have thawed

completely.TheUnited States Department of

Agriculture in Home and Garden Bulletin

No. 69 says:

“.. .YOUmay safely refreeze frozen foods that have
thawed if they stiIl contain ice crystals or if they are
will cold—below 40°F.

“.. .Thawed ground meats, poultry or fish that have
any off-odor or off-color should not be refrozen and
should not be eaten. Thawed ice cream should be
discarded. If the odor or color of any food is poor
or questionable, get rid of it. The food maybe
dangerous to eat.

“Even partial thawing and refreezing reduces the

eating quality of f~s, particularly fruits,
vegetables and prepared foods. The eating quality
of red meats is affected less than that of many other
foods. Use refrozen foods as soon as possible to
save as much of their eating quality as you can.”

cUnplug your refrigerator before

cleaning and making repairs.
NOTE: We strongly recommend that
any servicing be performed by a ,
qualified individual.

● Before replacing a burned-out bulb, unplug the

refrigerator or turn off the power at the circuit
breaker or fuse box in order to avoid contact with
a live wire filament. (A burned-out light bulb may
break when being replaced.) NOTE: Turning the
control to the OFF position does not remove
power to the light circuit.

cDo not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any
other appliance,

*

SAW THESE
INSTRUCTIONS

1

‘o

hands on the automatic ice-making mech~sm
while the reiiigerator is plugged in.

.

3

I

TEMl?ERAiURE CONTROLS

The temperature controls in your refrigerator

The freezer control

have letters and numbers. Initially set the freezer

moves a damper to

control at “C” and the fresh food control at”5 .“

change the amount

The fresh food

of cold air that

-

control maintains

moves from the

the temperatures

5 INITIAL SETTING

freezer to the fresh

9 COLDEST

throughout the

food compartment.

FRESH FOOD

refrigerator. Moving

Damper

“OFF” stops cooling in

I

both areas-fresh food and freezer—

Cold air

n E (coldest setting)

-c II

but does not shut off power to the refrigerator.

from freezer
com~artment

%&2$& ! !

‘ ‘=3%%

(warmest setting) A c

Power Saver Switch

The power saver switch is located on the temperature
control panel.

To reduce the amount of electricity required to
operate your refrigerator, push switch to the

POWER SAVER setting.

This turns off the heater in your refrigerator that

prevents moisture from forming on the exterior of
the refrigerator.

With the heater turned off, there is a chance that
moisture may form on the outside of your refrigerator,
especially when the weather is humid.

The humidity is most likely to be high in the summer,

in the early morning hours, and in homes which are
not air conditioned.

A

Over an extended period of time, moisture that forms
on the refrigerator surface may cause deterioration of
the paint finish. It will be important to protect the
finish by using appliance polish wax as described in
the Care and Cleanin~ section.

Move the power saver switch from the POWER

SAVER setting and electricity flows through the low

●

wattage heater which warms the inside of the divider

between the refrigerator and freezer.Under most

conditions, this prevents the forming of moisture or
water droplets.

. .

Use the milk test for the fresh food compartment.

It is not necessary to defrost the freezer or fresh food

Place a container of milk on the top shelf in the fresh “

compartments. Although your refrigerator is designed

food compartment. Check it a day later. If the milk is

and equipped to defrost itself automatically, some

too warm or too cold, adjust the temperature controls.

frost on packages is normal.

Use the ice cream test for the freezer compartment.

Place iicontainer of ice cream in the center of the
freezer compartment. Check it after a day. If it’s too
hard or too soft, adjust the temperature controls.

Always allow 24 hours for the refrigerator to reach
the temperature you set.

If you turn your household thermostat below 60° at night...

D

...you may want to move the freezer

Moving the freezer control to a colder setting should

,,,,8.,

control one step colder.Cooler have no effecton your fresh food compartment.

:

#

4

#o

..

.

temperatures in the house may cause However,if freezing occurs, move the fresh food

s
s

●

the compressor to operate less controlone step warmer.

!

-

●*

frequently,thus allowing the freezer

When you stop turning the thermostat down, turn the

compartment to warm somewhat. To

refrigerator’s controls back to their regultir settings.

protect your frozen food supply, leave the freezer
setting at this colder setting for the entire winter or for

●

as long as you keep your thermostat turned down.

5

FOOD STORAGE SUGGESTIONS

Suggested Storage Times for Meat and Poultry*

Eatingquality DAYSIN

MONTHSIN Eatingquality

DAYSIN MONTHS IN

dropsafter REFRIGERATOR

FREEZER dropsafter

REFRIGERATOR FREEZER

time shown AT35” to 40” F.

ATO“F.

time shown

AT35° to 40° F,

AT0° F.

(2° to 4°

c.)

(-18° C.)

(2° to 4°

c.)

(-18° C.)

Fresh Meats

Fresh Poultry

Roasts (Beef & Lamb) ...................... 3 to 5

6to12

Chicken & Turkey (Whole) ................ 1 to 2

12

Roasts (Pork & Veal) ........................ 3 to 5

4t08

Chicken (Pieces) .... ........... ................ 1 to 2

9

Steaks (Beef) ... ............... .................. 3 to 5

6to12 Turkey (Pieces) . .............. .................. 1 to 2

6

Chops (Lamb) . ............... ................... 3 to 5

6t09

Duck & Goose (Whole) ..................... 1 to 2

6

Chops (Pork) . ............... .................... 3 to 5

3t04

Giblets .... .................. ......................... 1 to 2

3

Ground & Stew Meats ...................... 1 to 2

3t04

Variety Meats .. ............... ................... 1 to 2

3t04

Cooked Poultry

Sausage (Pork) ............................... .. 1 to 2

lto2

Pieces (Covered with Broth) ..............1 to 2

6

Processed Meats

Pieces (Not Covered) ........................ 3 to 4

1

Cooked Poultry Dishes ..................... 3 to 4 4t06

Bacon .... ............... ............................. ... 7

1

Fried Chicken

... ................... .............. 3 to 4

4

Frankfuders . .................... ..................... 7

1/2

Ham (Whole) ... ............... ...................... 7

lto2

(Other than for meats & poultry)

FREEZER

Ham (Half) . ................ ....................... 3 to 5 lto2

Most fruits and vegetables ....................... .........................8.l2 months

Ham (Sllces) .. .............. ........................ . 3

lto2

Lean fish . ............. ........................ ........................ ...............6.8 months

Luncheon Meats . ............... ............... 3 to 5 Freezing

Fatty fish, rolls and breads,

soups, stew,casseroles .........2-3 months

Sausage (Smoked) ............................... 7 not recom-

Cakes, pies, sandwiches, leftovers (cooked),

Sausage (Dry & Semi-Dry) .............14 to 21 mended.

lCeCWTI (original caRon) ........................ ....................l month max.

Cooked Meats

*

U.S. Department of Agriadture

Cooked Meats and Meat Dishes, ....... 3 to 4 2t03

Gravy & Meat Broth .......................... 1 to 2 2t03

Meats,

fish and poultry purchased from the store vary in quality and

age; consequently, safe storage time in your refrigerator will vary.

—

Fresh Food Storage Tips

To store vegetables:

QUsethe vegetable drawers.They have been designedto

preserve the naturalmoistureand freshnessof produce.

. Covering vegetables with a moist towel helps

maintain crispness.

cAs a further aid to freshness, prepackaged vegetables

can be stored in their original wrapping.

Unfrozen meats, fish, and poultry:

● Always remove store wrappings.

. Rewrap in foil, plastic wrap or wax paper and

refrigerate immediately.

Cheese:

● Wrap well with wax paper or aluminum foil, or put

in a plastic bag.

● Carefully wrap to expel air and help prevent mold.

● Storeprepackagedcheeseinitsownwrappingifyouwish.

Tips on Freezing Foods

There are three essential requirements for efficient
home freezing.

1. Initial quality. Freeze only top-quality foods.

Freezing retains quality and flavor; it cannot
improve quality.

2. Speed. The quicker fruits and vegetables are frozen

after picking, the better the frozen product will be.
You’ll save time, too, with less culling and sorting
to do.

3. Proper packaging. Use food wraps designed

especially for freezing.

Tofreeze meat, fish and poultry, wrap well in freezer­weight foil (or other heavy-duty wrapping material),
forming it carefully to the shape of the contents.
This expels air. Fold and crimp ends of the package to
provide a good, lasting seal. Don’t refreeze meat that
has been completely thawed; meat, whether raw or
cooked, can be frozen successfully only once.

Fine-quality ice cream, with high cream content, will
normally require slight]y lower temperatures than more
“airy” already-packaged brands with low cream content.

● It will be necessary to experiment to determine the

freezer compartment location and temperature
control setting to keep your ice cream at the right
serving temperature.

“The rear of the freezer compartment is slightly

colder than the front.

New techniques are constantly being developed.

Consult the Couny Extension Sen’ice or your local

●

Utility Company for the latest information on

freezing and storing foods.

6

Shelves in the fresh food

To replace shelves: Select desired shelf height. With

compartment are adjustable,

shelf

frontraisedslightly,engage top lugs in tracks at

enabling you to make

rear of cabinet. Then lower front of shelf until it locks

elllcient shelf arrangements

into position.

to fit your family’s food

Tempered glass shelves (on some models) are

storage needs.

adjustable in the same manner.

To remove shelves: Tilt

shelf up at front, then lift it

❑

1

Up and out of tracks on rem Engagetop lug ~.

wall of refrigerator.

❑

4P

/

.,~

Lower tolock

intoplace

Multi-Position Shelves (on some models)

To provide extra storage

‘,
flexibility, some models
have a two-position
freezer-compartment
shelf that can be placed

●

on another set of shelf

.—— —
supports.
To relocate the two-position freezer compartment

shelf, lift slightly and move it sideways to free the
ends of the shelf from the holes in the walls. Then
tilt the shelf and take it out. To reinstall the shelf,
first insert one end and then the other into the second
set of holes.

Shelves on the Doors

Shelves on both doors keep frequently-used items
readily available. On some models, one of the fresh
food compartment shelves is deep enough to provide
gallon-bottle storage.

Divider (on some models)

II II

The divider prevents tipping, spilling or sliding of small items stored on the

h ,,

II

h

door shelf.
Place index finger and middle finger on either side of the divider near the

d

‘

-o

front and simDlv move it back and forth to fit your needs. ‘+ ‘7

:

.

*

7

STORAGE DRAWERS

Fruit & Vegetable Drawers Detachable Meat Drawer (on some models)

When replacing the The slide-out meat drawer
drawers, always push them

can be removed and taken

all the way in.

to the sink or food

Storage time will depend

preparation area.

upon the type of food and its

On wire shelf models, just

condition when placed in

slide drawer out, remove

the drawers. -

drawer cover from shelf above, relocate cover in the

Excess water that may

position you desire it and slide drawer back into place.

accumulate in the bottom of

On glass shelf models, the drawer and the adjustable

the drawers should be

shelf to which it attaches can be relocated at any level.

emptied and the drawers

The meat drawer in some glass-shelf models is

wiped dry,

partially sealed at the front and rear to help maintain

NOTE: On some models storage drawers are one piece.

high humidity for storage of meats and cheese, bacon,
hors d’oeuvres, spreads and snacks.

High-Humidity Drawer (on some models)

Low-Humidity Drawer (on some models)

This refrigerateddraweris designedto keepunwmpped

This refrigerated drawer is designed to provide lower

foods fresh by retaining the natural moisture content

humidity storage for items such as:

of foods such

tlS:

● Apples

● Nectarines

● Raspberries

● Aflichokes

● Celery

● LeflUce

● Radishes

● Apricots ● Oranges ● Strawberries

● Asparagus

● cherries

● Parsley ● Rhubarb

● Grapes

● peaches

● Squash,summer

● Beets, topped ● Corn

● Peas,green ● Spinach

● MljshrOtjms

● Pears ● Tangerines

●

● Blueberries

● Currants

● Plums

● Tomatoes, ripe

.

Carrots

● Greens, leafy

As in any refrigerated storage area, it is recommended
that foods with strong odors be stored wrapped—

foods such as:

● Broccoli

● cauliflower

● Parsnips

● Brusselssprouts ● Greenonions

● Turnips

● cabbage

ICE SERVICE

Ice Trays (on some models)

To release ice cubes, turn the tray upside down, hold it over a container,

and twist both ends.
For only one or two ice cubes, leave the tray right-side up, twist both ends

slightly, and remove as many cubes as you want.
Wash ice trays in lukewarm Wateronly. Do not put them in an

automatic dishwasher.

8

.-

..

AUTOMATIC ICEMAKER

(on some models)

.

Your icemaker will

Icemaker

Feeler arm in

produce eight cubes

sition

per cycle-

approximately 100 cubes
in a 24-hour period,
depending on freezer
compartment
temperature, room
temperature, number of
door openings and other
use conditions. Ice

If your refrigerator is operated before water
connection is made to the icemaker, keep the

icemaker feeler arm in the STOP (up) position as
shown above.

When the refrigerator
has been connected to

the water supply, move

the feeler arm to the ON
(down) position.

The ice cube mold will
automatically fill with
water after cooling to
freezing temperature,
and first cubes will
normally freeze after

Feeler arm in

ition

several hours. When cubes are solidly frozen, they
will be ejected from the mold into the ice storage bin
by means of a sweeper arm.

Icemaking will continue until the feeler arm senses a
sufficient accumulation of ice cubes in the storage bin
and halts the operation temporarily. For maximum ice
storage, level the stored cubes with your hand
occasionally. Be sure nothing interferes with the
swing of the feeler arm.

The icemaker ejects cubes in groups of eight and it is
normal for several cubes to be joined together.

Once your icemaker is in operation, throw away
the first few batches of ice cubes. This will flush

away any impurities in the water line. Do the same
thing after vacations or extended periods when ice
isn’t used.

Move the icemaker feeler arm to the STOP (up)
position when:

● home water supply is to be off for several hours.

. ice

storagebinis to be removed for a period of time.

“going away on vacation.
If ice is not used often, old cubes will become cloudy

and taste stale and will shrink. Empty [he ice storage
bin periodically and wash it in lukewarm water.

If this is your first icemaker, you’11hear occasional
sounds that may be unfi~miliar.They arc normal
icemaking sounds and are not cause for concern.

Water Filter Accessory

Your ice cubes can only be as fresh-tasting as the
water that produces them. That’s why it’s a good
idea to purify your water with a water filter.

Its activated charcoal removes musty, stale odors and
unpleasant medicinal, metallic tastes. A porous fiber
cartridge catches dirt, rust particles, sand and silt
while special crystals reduce deposits of hard scale.

The water filter is an option at extra cost and is

available from your dealer. Specify WR97X02 14.
It has complete installation instructions and installs
in minutes on 1/4” OD copper water line.

Water Supply Kit

A kit containing copper tubing, shut-oft VUIVC,fittings

and instructions needed to connect the iccnmkcr to

your cold water line is available at extra cost. Sec

Preparation section.

Icemaker Accessory Kit

If your refrigerator did not come already equipped

with an automatic icemaker, an Icemaker Accessory

Kit is available at extra cost. Check the back of the
refrigerator for the specific icemaker kit needed for
your model.

9

It&3

“.

“. -.
.-. , :.

.“<

:/, ,

CARE AND CLEANING

“.:b.,

.,

Cleaning—Outside

The door handles and trim (on some models) can be Do not use scouring pads, powdered cleaners, bleach,

cleaned with a cloth dampened with a solution of mild

or cleaners containing bleach, because these products

liquid dishwashing detergent and water. Dry with a

can scratch and weaken the paint finish,

soft cloth. Don’t wax handles or trim. -

Keep the finish clean. Wipe with a clean cloth,
lightly dampened with kitchen appliance wax or mild
liquid dishwashing detergent. Dry and polish with a

clean, soft cloth.
Do not wipe the refrigerator with a soiled

dishwashing cloth or wet towel. These may leave a
residue that can damage the paint.

Protect the paint finish. The finish on the outside
of the refrigerator is a high quality, baked-on paint
finish. With proper care, it will stay new-looking and
rust-free for years. Apply a coat of kitchen/appliance
wax when the refrigerator is new, and then at least
twice a year.

Appliance Polish Wax & Cleaner is available from
Service and Parts Centers.

Cleaning—Inside

Clean the inside of the fresh food and freezer

compartments at least once a year. Unplug the

refrigerator before cleaning. If this is not practical,

wring excess moisture out of sponge or cloth when
cleaning around switches, lights or controls.

Apply an appliance wax/polish to the inside surface
between the doors.

Use warm water and baking soda solution—about
a tablespoon of baking soda to a quart of water. This
both cleans and neutralizes odors. Rinse thoroughly
with water and wipe dry.

Other parts of the refrigerator—including door
gaskets, vegetable drawers, ice trays and all plastic
parts-can be cleaned the same way. Do not use
cleansing powders or other abrasive cleaners.

Avoid cleaning cold glass shelves with hot water
because the extreme temperature difference may
cause them to break.

To help prevent odors, leave an open box of baking
soda in the rear of the refrigerator, on the top shelf.

●

Change the box every three months. An open box of
baking soda in the freezerwill absorb stale freezerodors.

Do not wash any of your refrigerator’s plastic
parts in your automatic dishwasher.

Behind Refrigerator

Care should be taken in moving your refrigerator
away from the wall. All types of floor coverings can
be damaged, particularly cushioned coverings and
those with embossed surfaces.

Pull the refrigerator straight out and return it to position

by pushing it straight in. Moving your refrigerator in a

side direction may result in damage to your floor

covering or refrigerator. Refer to the Rollers section.

Under Refrigerator

The condenser is located
behind the base grille.

K

~1

For most efficient

p=

Y

operation, you need to
keep the condenser clean.
Turn temperature control

\\F

I

to OFF. Remove the base
grille. Sweep away or
vacuum dust that is

/

Clean the condenser coils

readily accessible on

atleastonceayear.
condenser coils, then turn
the control back on.

For best results, use a brush specially designed for
this purpose. It is available at most appliance and part

.stores. This easy cleaning operation should be done at

least once a year.

●

10

Storage Drawer and Drawer Cover Removal

Drawers at the bottom of the fresh food compartment

To remove the drawers and their covers when the

will stop before coming all the way out of the

fresh food compartment door cannot be opened fully,

refrigerator, to help prevent contents from spilling

follow the procedure that applies to your model.

onto the floor. These drawers can be removed easily
by lifting the sides up slightly while pulling the
drawers past the “stop” location.

~0 Drawers (on some models)

1. Remove the drawer
farthestfromthe door.

2. Remove the other
drawer.

●

3.

4.

On models with a
bottom door shelf

that blocks the other
drawer, slide the other
drawer toward the

middle and remove it.

Remove the glass
cover.Reach in, push

&hefront of the glass
cover up and. at the
same time, pull it
forward as far as it
will come. Tilt it and
take it out.

Remove the drawer

frame. (Always

remove the glass cover
before you take out
the drawer frame.)
Lift the frame off the
supports at each side
and back, pull it
forward, tilt it and
take it out.

&Ql I

‘*1

A. ‘—=, ___

——.

‘l---

/.—

—

—

\

\_ :___ _

; =-- -

~c===

—---/

To replace:

1.Lower the frame until it rests on the supports at

each side and back.

2. Replace the drawers.

If you removed the
drawer slide, replace it
with the sloped end at
the front.

a.

b.

c.

3.

Slide one side of the
drawer onto the

drawer slide.

Move the slide and
drawer all the way
to the hinge side
until the other side
of the drawer rests
on the frame.

Slide the other drawer into place.

Replace the glass cover, pushing its rear edge
firmly into the rear frame channel and gentl~
lowering the front into place,

11

CARE AND CLEANING

(continued)

Half-Width Drawers with Plastic Cover

To remove the drawers, lift front up slightly and pull
the drawer straight out. To remove the cover, support it

with one hand, tilt it and take it out.

–\

\

12

,/

Light Bulb Replacement

A light bulb and socket are located at the top of
the fresh food compartment opposite the temperature
control panel.

Some models also have a bulb and socket in the
upper left comer of the freezer compartment behind
a flexible light shield.

To replace either bulb, unplug refrigerator from its
electrical outlet, unscrew bulb when cool, and replace

with similar size bulb.

PREPARATION

Refrigerator Location

Clearances

Do not install refrigerator where temperature will

Allow the following clearances for ease of

go below 60°F’.because it will not run often enough

installation, proper air circulation and plumbing

to maintain proper temperatures.

and electrical connections:

Do install it on a floor strong enough to support it

Sides

................................

3/4”

fully loaded.

Top

1

?/

......................................

Back 1

?/

....................................

Rollers

Some models have adjustable rollers that allow you

Turn the two front roller adjusting

to move the refrigerator away from the wall for

screws clockwise to raise the

cleaning. Rollers should be set so the refrigerator is

refrigerator, counterclockwise to

-Ull

firmly ~ositioned on the floor and the fron~is raised

Iow&irit.

just enough (about 3/4” from the floor) that the doors

close easily when opened about halfway.

Remove the base grille

by grasping the bottom
of the grille and pulling

it out.

To replace the base
grille, line up the clips

on the back of the grille
with the openings in the
baseplate and push the

\

grille forward until it
snaps into place.

--J

Water Supply to Icemaker (on some models)

If your refrigerator has an icemaker, or if you plan to
add an icemaker later, the icemaker will have to be
connected to a cold water line. A water supply kit
containing copper tubing, shut-off valve, fittings and

instructions is available at extra cost from your dealer.
There should be sufficient tubing for the icemaker
from the cold water supply to allow you to move the
refrigerator out from the wall several feet
(approximately 8 feet of 1/4” copper tubing in three

10”diameter coils).

Preparing to Move

Disconnect power cord from wall outlet, remove all
food, and clean and dry the interior.

Secure all loose items such as grille, shelves and
storage pans, by taping them securely in place to
prevent damage.

Be sure refrigerator stays in upright position during
actual moving and in van. Refrigerator must be
secured in van to prevent movement. Protect the
outside of the refrigerator with a blanket.

Preparing for Vacation

For extended vacations or absences, remove food

For shorter vacations, remove perishable foods and

and shut off power to the refrigerator. Clean the interior

leave controls at regular settings. However, if room

with baking soda solution of one tablespoon of soda to

temperature is expected to drop below 60”F., follow

one quart of water. Wipe dry. To prevent odors, leave

same instructions as for extended vacations. Move the

open box of soda in refrigerator. Leave doors open.

icemaker feeler arm to the STOP (up) position and be
sure to shut off the water supply to the refrigerator.

13

I

INSTALLATION REQUIREMENTS

IMPORTANT... Please Read Carefully

How to connect electricity

●

For personal safety, this appliance must

Have the wall outlet and circuit checked by a qualified

be mo~erlv grounded.

electrician to make sure the outlet is properly grounded.

The power cord of this ~re~erre~~et~o~
appliance is equipped
with a three-prong

r

Q

9

yR

(grounding) plug which >

.L—

6

mates with a standard

,,

‘.

three-prong (grounding)
wall outlet to minimize
the possibility of electric

Insure proper

shock hazard from

grounding exists
before use.

this appliance.

If you have only a standard two-prong wall outlet,
it is your personal responsibility and obligation to
have it replaced with a properly grounded three­prong wall outlet.

DO NOT,UNDER ANY CIRCUMSTANCES,

CUTOR REMOVETHE THIRD(GROUNDING)

4

PRONG FROM THE POWER CORD.

Use of Adapter Plug

Because of potential
safety hazards under

certain conditions,

we strongly
recommend against
use of an adapter
plug. However, if
you still elect to use
an adapter, where
local codes permit,
a TEMPORARY CONNECTION may be made to
a properly grounded two-prong wall outlet by use
of a UL-listed adapter available at most local
hardware stores.

TemporaW method

(Adapter plugs not
permitted in Canada.)

P F

r

Align

large prongs/slots.

w

~_lnsure p;oper grounding

and firm connection

II

exists before use.

The larger slot in the adapter must be aligned with the

larger slot in the wall outlet to provide proper polarity
in the connection of the power cord.

CAUTION: Attaching an adapter ground terminal to
the wall outlet cover screw does not ground the
appliance unless the cover screw is mettil, and not
insulated, and the wall outlet is grounded through the
house wiring. You should have the circuit checked by
a qualified electrician to make sure the outlet is
pr~perly grounded.

When disconnecting the power cord from the
adapter, always hold the adapter with one hand. If

this is not done, the adapter ground terminal is very
likely to break with repeated use.

Should the adapter ground terminal break, DO
NOT USE the appliance until a proper ground has
again been established.

Electrical Requirements

The refrigerator should always be plugged into its
own individual electrical outlet which has a voltage

rating that matches the rating plate.
This provides the best performance and also prevents

overloading house wiring circuits, which could cause
a fire hazard from overheating wires.

Use of Extension Cords

Because of potential safety hazards under certain
conditions, we strongly recommend against the use of
an extension cord. However, if you still elect to use an
extension cord, it is absolutely necessary that it be a
UL-listed 3-wire grounding type appliance extension
cord having a grounding type plug and outlet and that
the electrical rating of the cord be 15 amperes
(minimum) and 120 volts.

NOTE: MODELS WITH

THIS TYPE OF HANDLE

DO NOT REVERSE.

L

I

IMPORTANE Once you begin, do not move
the cabinet until the door-swing reversal is
completed.

When reversing the door swing

Read these instructions all the way
through before starting.

Handle parts carefully to avoid scratching
the paint.

Set screws down by their related parts to
avoid using them in the wrong places.

Provide a non-scratchin~ work surface for
the doors.

—

TOOLS REQUIRED

● T?O or T25 Torxdriver,

whichever your model requires

● Phillips screwdriver

● 5/16” hex socket driver

● 3/8” socket and ratchet

(a &point socket is recommended)

● Masking tape

● Putty knife or thin blade screwdriver

These instructions are for changing the

hinges fkom the right side to the lefi side.

If you ever want to change the hinges back to the
right side, follow these same instructions

(merely reverse all references to left and right).

REMOVE THE DOORS

❑GENERAL

a. Unplug the refrigerator from its

electrical outlet.

b. Empty all door shelves, including the

dairy compartment.

❑ REMOVE FREEZER DOOR

a. Tape door shut

with

masking tape.

b. With Torxdriver, remove

2 Torx screws that hold

the top hinge to cabinet.

c. Lift hinge straight up to

fkee

hinge pin from socket

in top of door.

d. Remove tape, tilt door

j

away from cabinet and lifl

it to free its bottom socket ——————
from hinge pin on center
hinge bracket.

e. Set door on non-scratching surface with

outside up.

❑ REMOVE FRESH FOOD DOOR.

a. Tape door shut

Plastic

I

with masking tape.

washer

*

I

b. Remove the hinge

+

I

pin with a 3/8”

Hinge

socket and ratchet.

pm

c. Remove tape

J

and tilt door away cfln~~

4

G;

from cabinet.

Remove and save

~+

bracket Q \

washer on hinge pin.

s

1

d. Iift door straight

I

up to free its bottom

socket from pin in

%

>

bottom hinge bracket.

Fresh food door

I

d

m

m

CAUTION:Do not let either door drop to the

floor. To do so could damage the door stop.

(continued next page)

15

REVERSE HARDWARE OH CABINET

~ TRAKSFER BOTTOM HINGE BRACKET

TO THE LEFT.

a.

Remove the base grille. Grasp it at the bottom
and pull it straight out.

Tl

49

\

b. Using the Torxdriver, remove the hinge and

plastic washer from the bottom right side
of the cabinet.

Bottom left

Plastic

washer

#

c. Reinstall the hinge and plastic washer to the

bottom left side ofthe cabinet.

~ TRANSFER CENTER

THE LEFT.

Do not remove this screw I I

HINGE BRACKET TO

a.

Remove the center hinge bracket by removing

the three Torx screws. NOTE:

Keep these

screws with the hinge bracket. They are

longer screws and will be used when
installing the hinge on the other side.

b.

Removethe three Torx screws tiom the center

left

side ofthe cabinet. Screw them into the
holes on the right side, which were uncovered
in Step (a) above.

Center left

I

I I Do not remove this screw

Place the center hinge bracket over the holes at
the center left side of the cabinet, insert the three
screws that were removed with the center hinge
bracket in Step (a) and tighten them.

@ TRANSFER TOP HINGE TO THE LEFT.

I

Interchange hinge and screws at top right

with screws at top left of cabinet. Do not tighten

screws on hinge side at this time.

I

❑TRAKSFER DOOR STOPS.

a. On

each door, move the metal door stop from

the right end to the left end.

b.

Move anyscrews from the left end to the

right end.

16

,

●

●

✌

0

Left side

Top view

r

7

Bottom view

Bottom wew

❑ TRANSFER FRESH FOOD DOOR HANDLE

TO THE RIGHT.

a. Remove bottom cap by pushing it toward

bottom of door and remove screw underneath.

b. I?mo~re two screws holding handle to top

.
c. Remove handle.
d. Attach handle to right side of door with two

screws at top of door.

e. Screw bottom of handle into place, and slide

bottom cap onto handle.

~er removing the

Plug button

fresh food door handle:
a. Remove screws from

right edge of door top

0

and insert them into

Screws for

handle screw holes on

handle holes

left side.

b. Remove plug button

from left edge of door

Medalhon

1

and insert it into hole
on opposite side.

c. Transfer medallion on

-

door to opposite side.

d

❑TRAHSFER FREEZER DOOR HAHDLE TO

THE RIGHT.

Y

1=

a. Remove one screw

holding handle to top of
door and two screws
I#dld handle to bottom

.

b. Remove handle.

r

c. Transfer handle screw

from right edge of door

&

top and plug button from

;A

left edge of door top to

Left side

opposite side.

Right side

d. Attach handle to right side of door with screws

removed in step (a) above.

Plastic

a. Imwer bottom socket

washer+

of fresh food door

Hinge

1+

onto pin on bottom
hinge bracket. Be sure

pin ~

e j_

I

washer is in place.

b.Tilt door toward

Center

cabinet and gently

hinge

bracket

push door under
center hinge bracket

*~

@

and align with the hole in

Fresh

the center hinge bracket.

!% v

c. Reinstall hinge pin with

a 3/8” socket fid ;atchet so it extends through
hole in center hinge bracket and into socket
on top of fresh food door.

REHANG FREEZERDOOR

a. Lower bottom socket of freezer door onto

center hinge pin. Be sure washer is in place.

b.Tdt door toward cabine~ lifting the top hinge

so the pin fits into the socket on top of the door.

c. T@ten tie top hinge screws after supporting

the door on the handle side and aligning so
the gap between the doors is even all across
the front.

17

CAUTION:

● If you use your refrigerator before connecting

the water line, make sure the icemaker feeler

arm is kept in the STOP (up) position.

● Do not install the icemaker tubing in areas

where temperatures fall below freezing.

● When using any electrical device (such as a

power drill) during installation, be sure the
device is insulated or wired in a manner to
prevent the hazard of electric shock.

● All installations must be in accordance with

local plumbing code requirements.

WHAT YOU WILL NEED

● A cold water supply is required for automatic

icemaker operation. The water pressure must
be between 20 and 120 p.s.i.

● Power drill, unless you have a self-piercingvalve.

● Copper tubing, 1/4” outer diameter to

connect the refrigerator to the water supply.
Be sure both ends of the tubing are cut square.

To determine how much copper tubing you

need: measure the distance from the water valve
on the back of the retilgerator to the water
supply pipe. Then add 8 feet. Be sure there is

sufficient extra tubing (about 8 feet coiled into
3 turns of about 10 inches diameter) to allow the
refrigerator to move out from the wall after
installation. Do not use plastic tubing or plastic
fittings because the water supply line is under
pressure at all times. Also, certain types of
plastic tubing may become brittle with age and
crack, resulting in water leakage.

●

●

●

Shutoff valve to connect to the cold water

line. The shut-off valve should have a water
inlet with a minimum inside diameter of 5/32”
at the point of connection to the COLD WA~R
LINE. Saddle-type shut-off valves are included
in many water supply kits. Before purchasing,
make sure a saddk+type valve complies with
your local plumbing codes.

Two 1/4” outer diameter compression nuts
and 2 ferrules (sleeves)-to connect the
copper tubing to the shutoff valve and the
refrigerator water valve.

Ifyour existing water line has a flared fitting at
the

end, you WI1lneed an adapter (available at

plumbmg supply stores) to connect the water
line to the refrigerator OR—you can cut off the
flared fitting with a tube cutter and then use a
compression fitting.

WARRAHTY INFORMATION
This water line installationis not

warranted by

the refrigerator or icemaker manufacturer.

Follow these instructionscarefullytn minimim

the risk of expensive water damage.

In

1 SHUT OFF THE ~lN WATER SUPPLY.

I

Turn on the nearest faucet long enough to clear
the line of water.

I

❑ INSTALL THE SHUTOFF VALVE ON THE

NEAREST FREQUENTLY USED DRINKING
WATER LINE.

Typical ways to connectto water supply

pl- ~fl ~1~ Mu

Through floor

Under sink Through wall to

In crawl

to basement to cold utility room cold

space under

cold water pipe water pipe water pipe

house

a. Choose a location for the valve that is easily

accessible. It is best to connect into the side of
a vertical water pipe. When it is necessary to
connect into a horizontal water pipe, make the
connection to the top or side, rather than at
the bottom, to avoid drawing off any sediment
from the water pipe.

b. Drill a 1/4” hole in the water pipe, using a

sharp bit. Remove any burrs resulting from
drilling the hole in the pipe. (Do not drill a
hole if the valve is a self-piercing type.)

c. Fasten the shutoff

valve to the cold
water pipe with the
pipe clamp.

d. Tighten the clamp

screws until the
sealing washer

ical

begins to swell. Do

water

not over-tighten or
you may crush the
copper tubing.

18

~ ROUTE THE COPPER TUBING BETWEEN THE

COLD WATER LIHE AHD THE REFRIGERATOR

Route the tubing through a hole drilled in the
floor or wall (behind the retligerator or adjacent
base cabinet) as close to the wall as possible. Be
sure there is sufficient extra tubing (about 8 feet
coiled into 3 turns of about 10” diameter) to
allow the refrigerator to move out from the wall
after installation.

~ CONNECT THE COPPER TUBING TO THE

SHUTOFF VALVE.

t

Place the compression
nut and ferrule (sleeve)

ontothe end ofthe tubing
and connect it to the
shutoff valve. Make sure
the tubing is fully
inserted into the valve.

Tighten the compression ~u~le~,~1~~1

I

‘

Ferrule

nut securely.

(sleeve)

a.

b.

c.

d.

Remove the plastic flexible cap from the
water valve.

1)4” Copper

Tubing

Place the
compression nut

‘ubing\ I ‘“”b

andferrule (sleeve)

onto the end of the
tubing as shown.

e
e)

Insert the end of

the copper tubing

u,

I

into th-e-water
valveconnection

- ,&y

Compression mI*

as far as possible.
While holding

Refrigerator-connectIon

the tubing, ti~hten the fitting.
Fasten the copper tubing into the clamp

provided to hold it in a vertical position. You

‘mayneed to pry open the clamp.

❑ TURN THE WATER ON AT THE

SHUTOFF VALVE.

Tighten any connections that leak.

E TURN OH THE WATER AND FLUSH OUT

THE TUBING.

❑ PLUG THE REFRIGERATOR POWER CORD

a. Turn the main water supply on and flush out

INTO A GROUNDED ELECTRICAL OUTLET.

the tubing until the water is clear.

b. Shut the water off at the water valve after

about one quart of water has been flushed
through the tubing.

E CONNECT THE COPPER TUBING TO

THE REFRIGERATOR.

Before making the connection to the

refrigerator, be sure the refi=igerator power
cord is not plugged into the wall outleL

We recommend installing a water filter

(available at service and parts centers) if your

water supply has sand or particles that could
clog the screen of the retilgerator’s water valve.

Install it in the waterline near the refrigerator.

❑ SET THE ICEMAKER FEELER ARM TO THE

ON (DOWN) POSITION.

The icemaker will not begin to operate until it

reaches its operating temperature of 15°E or
below. It will then begin operation automatically
if the icemaker is in the ON (down) position.

NOTE: The icemaker may double-cycle when it
first starts, causing some water spillage from the
icemaker into the ice bucket. This is normal and
should not happen again. The first few batches of
cubes should be thrown away, so that remaining
impurities in the water line will be flushed out.

❑MOVE THE REFRIGERATOR BACK TO

THE WALL.

Arrange the coil of copper tubing so that it does

not vibrate against the back of the refrigerator or

against the wall.

19

7

●

QUESTIONS?

USE THIS PROBLEM SOLVER

●

PROBLEM

I

POSSIBLE CAUSE

REFRIGERATOR DOES

● May be in defrost cycle when motor does not operate for about 30 minutes.

NOT OPERATE

● Temperature control in OFF position.

I

cIf interior light is not on, refrigerator may not be plugged in at wall outlet.
“If plug is secure and the refrigerator still fails to operate, plug a lamp or a small

appliance into the same outlet to determine if there is a tripped circuit breaker or

burned out fuse.

MOTOR OPERATES . Modern refrigerators with more storage space and a larger freezer compartment
FOR LONG PERIODS require more operating time.

. Normal when refrigerator is first delivered to your home—usually requires

24 hours to completely cool down.

I

. L~argeamounts of food placed in refrigerator to be cooled or frozen.
. Hot weather—frequent door openings.

● Door left open.

. Temperature controls are set too cold. Refer to the TemperatureControls section.

● Grille and condenser need cleaning. Refer to the Care and Cletining section.

● Check Energy-Saving Tips.

MOTOR STARTS &

I

● Tempemture control starts and stops motor to nmintain even temperatures.

STOPS FREQUENTLY

.

VIBRATION OR RATTLING

● If the refrigerator vibrates, mom than likely it is not resting solidly on the floor.

The front rollers or leveling legs need xljusting, or floor is weak or uneven.

e

Refer to Rollers in the Preparation section.

● If dishes vibrate on shelves, try ]movingthem. Slight vibration is nornml.

The sound ofcubes dropping

into the bin and water running in pipes as icemaker refills.

20

●

PROBLEM

FOODS DRY OUT
FRESH FOOD OR FREEZER

COMPARTMENT
TEMPERATURE TOO WARM

FROST OR ICE CRYSTALS
ON FROZEN FOOD

AUTOMATIC ICEMAKER
DOES NOT WORK
(on some models)

CUBES TOO SMALL
SLOW ICE CUBE FREEZINC

ICE CUBES HAVE
ODOWTASTE

MOISTURE FORMS ON
OUTSIDEOF REFRIGERATOR

MOISTURE COLLECTS

INSIDE
REFRIGERATORHAS ODOR

HOT AIR FROM
BOTTOM OF
REFRIGERATOR

POSSIBLE CAUSE

. Foods not covered, wrapped or sealed properly.
. Temperature control not set cold enough. Refer to the Temperature Controls section.

● Warm weather—frequent door openings.

s Door left open for too long a time.
s Package holding door open or blocking air duct in freezer compartment.

● Door may have been left ajar or package holding door open.

● Too frequent or too long door openings.

. Frost within package is normal.

● Icemaker feeler arm in STOP (up) position.

“ Water supply turned off or not connected.
. Freezer compartment too warm.

● Piled up cubes in storage bin may cause iccmaker to shut off prematurely.

Remove storage bin from freezer compartment and level cubes in bin by hand.

● Water shutoff valve connecting refrigerator to home water line may be clogged.

. Door may have been left open.

● Tulmtemperature control to colder setting.

● [f the doors are not opened regularly, the ice cube freezing rate will be reduced,

c Old cubes need to be discarded.

● Ice storage bin needs to be emptied and washed.

. Unsealed packages in refrigerator and/or freezer compartments may be

transmitting odor/taste to ice cubes.

. Interior of refrigemtor needs cleaning. Refer to the Care tind Cleaning section.

● Poor-tasting incoming water. Install a water tlltcr.

“ Not unusual during periods of high humidity.
. Move the Power Saver Switch to the moisture setting.

● Too frequent or too long door openings.

s in humid weather, air carries moisture into refrigerator when doors arc opened.

● Foods with strong odors should be tightly covered.

● Check for spoiled food.

c Interior needs cleaning. Refer to the Care and Cleaning section.

● Defrost water system needs cleaning.

. Keep open box of baking soda in refrigerator; replace every three months.

● Normal air flow cooling motor. In the refrigeration process. it is normal that

heat be expelled in the area under the refrigerator. Some floor coverings will
discolor at these normal and safe operating temperatures. Your floor covering
supplier should be consulted if you object to this discoloration.

If you need more help. ..call, toll free:

GE Answer Center”

800.626.2000

consumer information service

21

NOTES

22

Wdll Be There

With the purchase of your new appliance, receive the assurance that ifyou ever need

information or assistance, we’ll be there. All you have to do is call—toll-free!

/mHomeRepairSemite

8111WE~RES(801W2-2737)

Our consumer serviceprofessional willprovide expert repair serviceon your
newappliance, scheduled at a time that’s convenient for you. ManyGE
Consumer Servicecompany-operated locations offeryou service today or
tomorrow, or at your convenience (’7:00a.m. to

7:00 p.m. weekdays,9:00 a.m.

to 2:00 p.m. Saturdays). Our factory-trained technicians knowyour appliance
inside and out—somost repairs can be handled injust one visit.

GEAnswerCente~

8011621i2000

Whatever your question about your newappliance, GE Answer Center@
information serviceisavailable to help. Your call—andyour question-will be
answered promptly and courteously. And you can call any time. GEAnswer
Center@service is open 24 hours a day, 7 daysa week.

71TI”

{

,-

●eclm Aa

“u,~,um--. ., . . . . . 0..—

—..

-,.

ForCustomemWti SpecialNeeds...

801162ki2000

Upon request, wewillprovide
Braillecontrols for a variety of
appliances, and a brochure to
assistin pianning a barrier-free
kitchen for persons with limited
mobility. TOobtain these items,
free ofcharge, call 800.626.2000.

Consumers with impaired hearing or speech who have
accessto a TDDor a conventional teletypewriter may
call800-TDD-GEAC(800-833-4322)m request
information or sewice.

ServiceCon&acts

8006252224

You can have the secure feeling that GE Consumer Service will still be there
after your product warranty expires. Purchase a GEcontract while your

warranty isstill in effectand you’llreceive a substantial discount. With
a multiple-year contract, you’re assured of future serviceat today’sprices.

Pa& andAccessories

801M2&2002

Individuals qualified to service their ownappliances can

User maintenance instructions contained in this booklet

have needed parts or accessories sent directly to their

coverprocedures intended to be performed by anyuser.

home. Our parts systemprovides accessto over 47,000

Other servicing generallyshould be referred to qualified

Genuine Renewal Parts...and all are fullywarranted.

servicepersonnel. Caution must be exercised, since

VISA,MasterCard and Discovercards are accepted.

improper servicing may cause unsafe operation.

YOUR REFRIGERATOR

Staple sales slip or cancelled check

WARRANTY

here. Proof of original purchase date

is needed to obtain service

under warranty.

i

WHAT IS COVERED

FULL ONE-YEAR WARRANTY

For one year from date of original
purchase, we will provide, free of
charge, parts and service labor in

your home to repair or replace any
part of the refrigerator that fails
because of a manufacturing defect.

FULL FIVE-YEAR WARRANTY

For five years from date of original
purchase, we will provide, free of
charge, parts and setvice labor in
your home to repair or replace any

part of the sealed refrigerating
system (the compressor,

condenser, evaporator and all
connecting tubing) that fails
because of a manufacturing defect,

This warranty is extended to
the original purchaser and any
succeeding owner for products
purchased for ordinary home use
in the 48 mainland states, Hawaii
and Washington, D.C. In Alaska the
warranty is the same except that it
is LIMITED because you must pay
to ship the product to the service
shop or for the service technician’s
travel costs to your home.

All warranty service will be
provided by our Factory Service
Centers or by our authorized
Customer Car@ servicers during
normal working hours.

Should your appliance need
service, during the warranty period
or beyond, call 800-GE-CARES
(800-432-2737).

WHAT IS NOT COVERED

● Service trips to your home to

teach you how to use the product.

Read your Use and Care material.

If you then have any questions
about operating the product please
contact your dealer or our

Consumer Affairs office at the
address below, or call, toll free:

GE Answer Cente@

800.626.2000
consumer information service

c Improper installation.

If you have an installation problem,
contact your dealer or installer.

You are responsible for providing
adequate electrical, plumbing and
other connecting facilities.

● Replacement of house fuses or

resetting of circuit breakers.

● Failure of the product if it is used

for other than its intended
purpose or used commercially.

● Damage to product caused

by accident, fire, floods or acts

of God.
QLoss of food due to spoilage.
WARRANTOR IS NOT

RESPONSIBLE FOR

CONSEQUENTIAL DAMAGES.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion

may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

To know what your legal rights are in your state, consult your local or state consumer affairs office or your state’s Attorney General.

Warrantor: General Electric Company

If further help is needed concerning this warranty, write:

Manager—Consumer Affairs, GE Appliances, Louisville, KY 40225

This book is printed on recycied paper.

Part No. 162D6735POOI
Pub. No. 39-6299

D

1)

Top-Mount No-Frost 1

*

21 and 24 Models

7-94 CG

Printed in Louisville, KY